Introduction 4Instrument Cluster 10Warning lights and chimes 10Gauges 15Entertainment Systems 18AM/FM stereo 18AM/FM stereo with CD 20AM/FM stereo cas
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
To reduce the risk of possible serious injury: Do not hang objectsoff seat back or stow objects in map pocket (if equipped) whena child is in the fron
Press to move the front portion ofthe seat cushion up or down.Press to move the rear portion ofthe seat cushion up or down.Using the power lumbar supp
• Push the indicated side of thecontrol for minimum heat.• Push again to deactivate.The heated seat module resets at every ignition run cycle. While t
Your vehicle’s Personal Safety System娂 consists of the following items:• Driver and passenger dual-stage airbag supplemental restraints• Front safety
information early in the crash event on the severity of the impact. Thisallows your Personal Safety System娂 to distinguish between differentlevels of
When the front passenger seat is occupied and the sensing system hasturned off the passenger’s frontal airbag, the “pass airbag off” indicatorwill lig
• The warning light will not illuminate immediately after ignition isturned on.• A series of five beeps will be heard. The tone pattern will repeatper
Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue thatare designed to be used as
Energy management feature• This vehicle has a safety belt system with an energy managementfeature at the front outboard seating positions to help furt
movement. For example, if the driver brakes suddenly or turns a cornersharply, or the vehicle receives an impact of approximately 5 mph(8 km/h) or mor
Check engine: The Check engineindicator light illuminates when theignition is first turned to the ONposition to check the bulb and toindicate whether
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
Front safety belt height adjustmentYour vehicle has safety belt heightadjustments for the driver and frontoutboard passenger. Adjust theheight of the
For proper care of soiled safety belts, refer to Interior in the Cleaningchapter.Safety belt warning light and indicator chimeThe safety belt warning
If... Then...The driver’s and front passenger’ssafety belts are buckled before theignition switch is turned to the ONposition or less than 1-2 minutes
Reasons given... Consider...“I was in a hurry” Prime time for an accident. BeltMinder威reminds us to take a few seconds to buckle up.“Safety belts don’
Deactivating/activating the BeltMinder姞 featureThe driver and front passenger BeltMinder威 aredeactivated/activated independently. When deactivating/ac
4. Within 10 seconds of the light turning on, at a moderate speed, bucklethen unbuckle the safety belt.• This will disable the BeltMinder威 feature for
All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bagsupplemental restraint system (
The front passenger airbag is not designed to offer protection toan occupant in the center front seating position.Modifying or adding equipment to the
How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suffic
Brake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON
The SRS consists of the following items:• Driver and passenger airbag modules (which include the inflators andairbags)• safety belt pretensioners• Fro
detect the presence of a properly seated occupant and determine if thefront passenger’s frontal airbag should be enabled (may inflate) ordisabled (wil
• If the child restraint has been installed and the indicator lamp is notlit, then turn the vehicle off, remove the child restraint from thevehicle an
After all occupants have adjusted their seats and put on safety belts, it’svery important that they continue to sit properly. A properly seatedoccupan
• Objects placed on the occupant’s lap• Cargo interference with the seat• Other passengers pushing or pulling on the seat• Rear passenger feet and kne
• If the airbag readiness lamp remains illuminated, this may or may/notbe a problem due to the front passenger sensing system.DO NOT attempt to repair
Seat-mounted side airbag system (if equipped)Do not place objects or mount equipment on or near the airbagcover on the side of the seatbacks of the fr
How does the side airbag system work?The design and development of theside airbag system includedrecommended testing proceduresthat were developed by
Several air bag system components get hot after inflation. Do nottouch them after inflation.If the side airbag hasdeployed, the airbag willnot functio
Important child restraint precautionsYou are required by law to use safety restraints for children in the U.S.and Canada. If small children (generally
Charging system: Illuminates whenthe battery is not charging properly.Engine oil pressure: Illuminateswhen the oil pressure falls below thenormal rang
To improve the fit of both the lap and shoulder belt on children whohave outgrown child safety seats, Ford Motor Company recommends useof a belt-posit
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto
Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in acollision.SAFETY SEATS F
tether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. Formore info
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a
Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a
4. Open the tether anchor cover.5. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safetyseat may not
Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol.The anchors on both sides of thec
Low fuel (if equipped):Illuminates when the fuel level inthe fuel tank is at or near empty(refer to Fuel gauge in this chapterfor more information).O/
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙blowout⬙,with unexpected loss of
when you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive.2. Remove the cap from the valve on one t
Tire wearWhen the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Buil
designating where it was manufactured, the next two are the tire sizecode and the last four numbers represent the week and year the tire wasbuilt. For
When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of thetire to set the beads without ad
Highway hazardsNo matter how carefully you drive there’s always the possibility that youmay eventually have a flat tire on the highway. Drive slowly t
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
SNOW TIRES AND CHAINSSnow tires must be the same size and grade as the tires youcurrently have on your vehicle.The tires on your vehicle have all weat
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
Odometer: Registers the total miles (kilometers) of the vehicle.• Without Message CenterTo switch the display from Metric toEnglish, press and hold th
2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle.3. Subtract the combined weight of the driver and pas
1400 - (2 x 220) - (9 x 100) = 1400 - 440 - 900 = 60 lb. Now you havethe load capacity to transport the cement and your friend home. Inmetric units, t
If you use a rental trailer, follow the instructions that the rental agencygives to you.Do not attach safety chains to the bumper.Trailer brakesElectr
Trailer towing tips• Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turni
Replace the rear axle lubricant any time the axle has been submerged inwater. Rear axle lubricant quantities are not to be checked or changedunless a
STARTINGPositions of the ignition1. OFF/LOCK, shuts off the engineand all accessories/locks thegearshift lever and allows keyremoval.2. ACC, allows th
If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf
5. Turn the key to 3 (ON) withoutturning the key to 4 (START).Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrum
Do not use starting fluid such as ether in the air intake system. Suchfluid could cause immediate explosive damage to the engine and possiblepersonal
Use of an engine block heater is strongly recommended if you live in aregion where temperatures reach -10°F (-23°C) or below. For bestresults, plug th
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe
snowy roads is normal and indicates proper functioning of the vehicle’santi-lock brake system. If the vehicle has continuous vibration or shudderin th
illuminated with parking brake released. (If your brake warning lampilluminates, have your vehicle serviced immediately.)Parking brake with auto-relea
If the parking brake fails to releaseafter completing this procedure, usethe manual parking brake releaselever.Pull the lever to manually releasethe p
During Traction Control娂 operation you may hear an electric motor typeof sound coming from the engine compartment and the engine will not“rev-up” when
It is also important to maintain a proper power steering fluid level in thepower steering fluid reservoir:• Do not operate the vehicle with a low powe
If you exceed the load limit, the rear air suspension may not operate.The air suspension shut-off switch islocated on the left side of the trunk.If th
2. Locate the access plug on theunderside of the steering columncover.3. Remove the access plug using a flat head screwdriver. Insert thescrewdriver i
2. Insert the key and turn it to ACC. Apply the brake pedal and shiftto N (Neutral).When the key is in the ignition and in the ACC position, theautoma
• Depress the brake pedal• Move the gearshift lever into the desired gearTo put your vehicle in P (Park):• Come to a complete stop• Move the gearshift
If your vehicle is equipped with afloor-shift transmission, overdrivecan be deactivated by pressing thetransmission control switch on thegearshift han
AUDIO SYSTEMSAM/FM stereo (if equipped)1. Seek: Press/ to find thenext strong station down/up thefrequency band.2. Tune: Press/ to manuallychange radi
• Allows upshifts by moving gearshift lever.• Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
Canadian customers refer to your Owner Information Guide forinformation on:• coverage period• exact fuel amounts• towing of your disabled vehicle• eme
• The hazard lights control islocated on top of the steeringcolumn.• Depress hazard lights control toactivate all hazard flasherssimultaneously.• Depr
3. If no fuel leak is apparent, reset the fuel pump shut-off switch bypushing in on the reset button.4. Turn the ignition to the ON position. Pause fo
COLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge50A — — Red Red Red60A — — Blue Yellow Yellow70A — — Tan — Brown80A
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 10A Ignition (START) - Starter relaycoil, DTRS2 7.5A Power mirrors, Door
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description13 10A Ignition (ON) - Anti-lock BrakeSystem (ABS) module, Rear AirSuspensi
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description24 10A Ignition (ON/START) - PassiveAnti-Theft System (PATS)module, Powertr
The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 30A* Ignition switch2 20A* Moon roof, S
5. Power/volume: Press to turnON/OFF; turn to increase ordecrease volume levels.6. Tone: Press TONE until thedesired level — Bass, Treble, Fadeappears
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription12 20A* Audio (Subwoofer)25A* Tray lamps (Police vehicles only)13 20A* Instrument pan
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription108 20A** Police accessory battery feed 3(Police vehicles only)109 20A** ABS module (
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription208 — Not used2091⁄2ISO relay Horn301 Full ISO relay Starter302 Full ISO relay Air co
and tread design. If this is the case, this dissimilar spare tire is still ratedfor your vehicle loads (GAWR and GVWR).The use of tire sealants may da
Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following:• Handling, stability and braki
Full-size Matching Spare Tire/Wheel InformationThis spare tire/wheel will match the road tire/wheel. When driving withthe full size matching spare tir
3. Remove the spare tire and thejack. The jack could be located:• A — behind the mini spare tire or• B — behind the full size sparetireOn vehicles equ
5. Locate pry off notch (ifequipped) and remove the centerornament from the aluminum wheelwith the tapered end of the wheelnut wrench that came with y
To lessen risk of personalinjury, do not put any partof your body under the vehiclewhile changing a tire. Do not startthe engine when your vehicle iso
Bolt size Wheel lug nut torque*lb.ft. N•m1⁄2x 20 100 135* Torque specifications are for nut and bolt threads free of dirt andrust. Use only Ford recom
Seating and Safety Restraints 97Seating 97Safety restraints 102Airbags 116Child restraints 128Tires, Wheels and Loading 140Tire information 140Vehicle
AM/FM Stereo Single CD Premium audio system (if equipped)1. CD slot: Insert a CD, label sideup. With the ignition on, the radiowill begin play when a
3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake onboth vehicles
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
5. Eject: Press to eject the CD. Ifthe disc is not removed within theallotted time, the system willautomatically reload the CD and begin play. Note: T
If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
WAXINGApplying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage.• Wash the ve
• Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage.• Do not spray a ho
WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub
Do not use chemical solvents or strong detergents when cleaningthe steering wheel or instrument panel to avoid contamination ofthe airbag system.• Be
LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• To clean, use a soft cloth with Motorcraft
Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20)Motorcraft Engine Shampoo (Canada only) (CXC-66-A)Motorcraft One Step Wash and Wax Concentr
When activated, AUTOSET will momentarily appear in the display whenany of the preset controls are pressed.Speed sensitive volume: Radio volume changes
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under theinstrument panel.2. Go to the front of the vehicle andrelease the
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.6L SOHC V8 engine1. Brake fluid reservoir2. Engine oil dipstick3. Windshield washer fluid reservoir4
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
Poor wiper quality can be improved by cleaning the wiper blades and thewindshield, refer to Windows and wiper blades in the Cleaningchapter.To prolong
• If the oil level is within thisrange, the oil level is acceptable.DO NOT ADD OIL.• If the oil level is below thismark, engine oil must be addedto ra
To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level indicator and/or the engine oil filler cap removed.Engine oil and filt
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If
Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyeswhen working near
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
16. SCAN: Press SCAN to hear abrief sampling of radio stations orCD tracks. Press again to stop.Premium/Audiophile Satellite Compatible AM/FM Stereo S
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur
remove the coolant pressure relief cap on the radiator of a vehicle withan overflow system, follow these steps to add engine coolant.To reduce the ris
Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium
• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i
1. Pull off the road as soon as safely possible and turn off the engine.2. Arrange for the vehicle to be taken to an authorized dealer.3. If this is n
Automotive fuels can cause serious injury or death if misused ormishandled.Fuel ethanol and gasoline may contain benzene, which is acancer-causing age
“Fuel Ethanol ”. To identify if your vehicle is an FFV, check your VINor the label on the inside of your fuel filler door. When checking theVIN look f
RefuelingFuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others:• Read and follow all the instr
If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any
3. BASS: Press BASS; thenpressSEL-TEXT todecrease/increase the level of bassoutput.TREB (Treble): Press TREB; thenpressSEL-TEXT todecrease/increase th
Cleaner airFord endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality, per the recommendations in the Choosing the RightF
Unleaded Gasoline enginesIf you are experiencing starting, rough idle or hesitation driveabilityproblems during a cold start, try a different brand of
ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform
Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers).2. Each time you fill the tan
• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between the top gears occurs. Unnecessaryshifting of this type co
The EPA window sticker should be your guide for the fuel economycomparisons with other vehicles.It is important to note the box in the lower left corn
Exhaust leaks may result in entry of harmful and potentiallylethal fumes into the passenger compartment.Do not make any unauthorized changes to your v
If the indicator remains on, have your vehicle serviced at the firstavailable opportunity. Although some malfunctions detected by theOBD-II may not ha
POWER STEERING FLUIDCheck the power steering fluid.Refer to scheduled maintenanceinformation for the service intervalschedules. If adding fluid isnece
add fluid. If the fluid levels are outside of the normal operating range,the performance of your brake system could be compromised, seekservice from y
stations are independently operated and individually elect to use RDStechnology to transmit station ID and program type as desired.FIND Program type:
Correct fluid levelThe transmission fluid should be checked at normal operatingtemperature 150°F-170°F (66°C-77°C) on a level surface. The normalopera
If an overfill occurs, excess fluidshould be removed by an authorizeddealer.An overfill condition oftransmission fluid may causeshift and/or engagemen
Note: Be sure the hinge features of the air filter cover to the air filterhousing are fully engaged when reassembling the air filter assembly.Note: Fa
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationBrake fluidFill to line onreservoirMo
Item Capacity Ford part nameFord part number /Ford specificationHinges, latches, strikerplates, fuel filler doorhinge and seat tracks— Multi-Purpose G
Item Capacity Ford part nameFord part number /Ford specificationFuel tank19.0 gallons(71.9L)——1Use only brake fluids certified to meet Ford specificat
ENGINE DATAEngine 4.6L V8 engine 4.6L FFV V8 engineCubic inches 281 281Required fuel 87 octane 87 octane or Ethanol(E 85)Firing order 1-3-7-2-6-5-4-8
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
Dolby: Works in tape mode to reduces tape noise and hiss. Press MENUuntil DOLBY XX appears in the display. PressSEL-TEXT totoggle ON/OFF.The Dolby威 no
Peace of mindMobile-ease娂 hands-free communication systemRemote startVehicle security systemsWheel locksNot all accessories are available for all mode
AABS (see Brakes) ...169Air cleaner filter ...251–252Air conditioning ...35Air suspension ...
wiper blades ...216Climate control (see Airconditioning or Heating) ...35Clock adjust6-CD in dash ...
FFail safe cooling ...234Flexible Fuel Vehicle (FFV) ...235Floor mats ...79Fluid capacities ...
autolock ...82keypad ...89programming entry code ...90Keys ...
Relays ...184, 192Remote entry system ...85, 89illuminated entry ...88locking/unlocking doors
recreational towing...164trailer towing...161wrecker...204Traction control...
267
268
269
13. SCAN: Press SCAN to hear abrief sampling of radio stations,selections or CD tracks. Press againto stop.14. SHUF (Shuffle): Press to playthe tracks
270
271
272
Audiophile AM/FM Satellite Compatible Stereo In-dash Six CDsound system (if equipped)1. CD slot: To insert a CD, pressLOAD. When the system is ready,i
4. MUTE: Press to mute the playingmedia. Press again to return to theplaying media or turn the volumecontrol to adjust the volume.5. Eject: Press to e
Maintenance and Specifications 220Engine compartment 222Engine oil 224Battery 227Engine coolant 229Fuel information 235Air filter(s) 251Part numbers 2
9. MENU: Press MENU repeatedlyto access RDS on/off.UseSEL-TEXT to toggleRDS on/off. Press MENU again to access Program type mode or ShowType mode. (ME
Speed sensitive volume: Radio volume changes automatically andslightly with vehicle speed to compensate for road and wind noise.Recommended level is 1
16. SHUF (Shuffle) /SCAN: Press SCAN to hear a brief sampling ofradio stations or CD tracks on the current CD. Press again to stop.SHUF (Shuffle): Pre
CD/CD player care:Do:• Handle discs by their edges only. Never touch the playing surface.• Inspect discs before playing. Clean only with an approved C
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature sele
To aid in side window defogging/demisting in cold weather:1. Select NORM A/C.2. Adjust the temperature control to maintain comfort.3. Set the fan spee
3. Fan speed: Turn to manuallyincrease or decrease fan speed.4. Defrost:Distributes outside air through the windshield defrostervents and the side win
• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield.To aid in side window defogging/demisting in cold weather:1. Se
HEADLAMP CONTROLTurns the lamps off.Turns on the parkinglamps, instrument panel lamps,license plate lamps and tail lamps.Turns the headlamps on.Autola
Flash to passPull toward you slightly to activateand release to deactivate.Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a redu
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident the alignment of yo
With overhead consoleWith overhead console and moonroofTo turn on the map lamps, press themap lamp control.Rear courtesy/reading lampsRotate the lens
Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an
Overhead console lampsTo remove and replace the lamps in the overhead console:1. Make sure the headlamp switch isin the OFF position and remove theove
6. Without turning, remove the oldbulb from the lamp assembly bygently pulling it straight back out ofthe lamp assembly.To install the new bulb:Handle
3. Remove the screw from the outside of the lamp.4. Remove the nut from inside the lamp and pull the lamp assemblyforward.5. Disconnect the electrical
4. Pull the bulb from the socket andpush in the new bulb.5. Install the bulb socket into thelamp assembly by rotating itclockwise.6. Install the lamp
Replacing high-mount brakelamp bulbs1. Remove two screws from thelamp assembly.2. Carefully lift the lamp assemblyup for access to the bulbs.3. Carefu
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT STEERING WHEELTo adjust the steering wheel:1. Pull and hold the steering wheelrelease control toward you.2. Move the steering wheel up ordown unt
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
CENTER CONSOLE (IF EQUIPPED)Your vehicle may be equipped with a variety of console features. Theseinclude:• Utility compartment• Power point (inside s
3. Press and hold the MODE controluntil VAR appears in the display,then release. The display shouldshow the current zone number.4. Press the MODE cont
3. From a blank display press andrelease the MODE button once. Thedirectional heading will bedisplayed.Note: If the compass isde-calibrated, CAL will
4. Determine which magnetic zoneyou are in by referring to the zonemap.5. Repeatedly press and release theRESET button to scroll through thezones 1–15
4. Press the RESET button tode-calibrate the compass. Thedisplay will read CIRCLE SLOWLYTO CALIBRATE for a few secondsand then display a direction wit
ProgrammingDo not program the HomeLink威 with the vehicle parked in thegarage.Note: Some vehicles may require the ignition switch to be turned to these
3. Simultaneously press and holdboth the HomeLink威 and hand-heldtransmitter button. The messageCHANNEL “X” (1,2 or 3) TRAININGwill appear on the displ
If the indicator light(s) underneath the house icon blink rapidly for twoseconds and then turn to a continuous light, proceed with steps 6through 8 to
Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and release the appropriate HomeLink威 button.Activation will now occur for the
1. Press and hold the desiredHomeLink威 button. DO NOTrelease the button. The display willread CHANNEL “X” (1,2 or 3)TRANSMIT2. The display will change
SPECIAL NOTICESNew Vehicle Limited WarrantyFor a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited
Cigar/Cigarette lighter (if equipped)Do not plug optional electrical accessories into the cigarette lightersocket.Do not hold the lighter in with your
Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controlsexcept for the driver’s press
Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re
Do not use the speed control in heavy traffic or on roads thatare winding, slippery or unpaved.Setting speed controlThe controls for using your speedc
Resuming a set speedPress the RESUME control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RESUME control w
• Depress the brake pedal until thedesired vehicle speed is reached,press the SET + control.Turning off speed controlThere are two ways to turn off th
In any mode:• Press VOL + or - to adjust thevolume.Climate control features• Press TEMP + or - to adjusttemperature.MOON ROOF (IF EQUIPPED)Do not let
To vent the moon roof:• Press and hold the controlforward to raise the moon roof tothe vent position (when the glasspanel is closed).To open the moon
ProgrammingDo not program HomeLink威 with the vehicle parked in the garage.Note: Some vehicles may require the ignition switch to be turned to thesecon
• If the indicator light stays on constantly, programming is completeand your device should activate when the HomeLink威 button is pressedand released.
• how far (if at all) the driver was depressing the accelerator and/or thebrake pedal;• how fast the vehicle was traveling; and• where the driver was
• Continue to press and hold the HomeLink威 button (note Step 3 in the“Programming” section) while you press and release — every twoseconds (“cycle”) y
2. The indicator light will begin to flash after 20 seconds. Withoutreleasing the HomeLink威 button, follow Step 2 in the “Programming”section.For ques
Selectable featuresSelectPress this control to select functions shown in the INFO menu andSETUP menu.ResetPress this control to reset functions shown
Distance to empty (DTE)Selecting this function from theINFO menu estimates approximatelyhow far you can drive with the fuelremaining in your tank unde
Instantaneous fuel economySelect this function from the INFOmenu to display your instantaneousfuel economy. This will display yourfuel economy as a Ba
System checkSelecting this function from theSETUP menu causes the messagecenter to cycle through each of thesystems being monitored. For eachof the mo
Text Size1. Select this function from theSETUP menu.2. Press the SELECT control tochange text size.Units (English/Metric)1. Select this function from
2. Press the SELECT control tochange oil value.System warningsSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operatin
Warning display StatusOverdrive ON/OFF Warning returns after the ignition keyis turned from OFF to ON.Trunk ajarCheck compass moduleLow washer fluidCh
LOW WASHER FLUID. Indicates the washer fluid reservoir is less thanone quarter full. Check the washer fluid level. Refer to Windshieldwasher fluid in
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
Position the driver floor mat so thatthe eyelet is over the pointed end ofthe retention post and rotateforward to lock in. Make sure thatthe mat does
KEYSThe vehicle is equipped with a master (black) key and valet (gray) keylock system (if equipped with valet feature).• The master key will access th
The vehicle may still be locked with the key in the ignition, andperforming one of the following actions:• Pressing the manual lock button on the door
Deactivating/activating the autolock or auto-unlock featureAutomatic door locks can also be turned on/off through the followingprocedure:You must comp
CHILDPROOF DOOR LOCKSWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo
Keep vehicle doors andluggage compartmentlocked and keep keys and remotetransmitters out of a child’s reach.Unsupervised children could lockthemselves
Unlocking the doors1. Press and release to unlock the driver’s door. Note: The interiorlamps will illuminate.2. Pressand release again within five sec
Replacing the batteryThe remote entry transmitter uses one coin type three-volt lithiumbattery CR2032 or equivalent.To replace the battery:1. Twist a
If a remote transmitter has been lost and you would like to remove itfrom the vehicle’s memory, or you would like to purchase additionalremote transmi
The dome lamp control must not be set to the off position for theilluminated entry system to operate.The inside lights will not turn off if:• they hav
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
Programming a personal entry codeYou can program up to three personal codes to unlock your vehicle.These codes do not replace the permanent code that
• Do not use five numbers in sequential order.• The factory set code will work even if you have set your own personalcode.Erasing personal codeTo eras
started unless a coded key programmed to your vehicle is used. Theuse of the wrong type of coded key may lead to a “no-start” condition.This device co
Immobiliser System PATS XCVR certification numbersSaudi Arabia (10/1900)South Korea R-LPD1-04-0145Tunisia 269/MAT/2004United Arabian Emirates 5/10-2/3
If a problem occurs with the SecuriLock娂 system, the indicator will flashrapidly or glow steadily when the ignition is in the 3 (ON) position. Ifthis
If two previously programmed coded keys are not available, you mustbring your vehicle to your authorized dealer to have the spare codedkey(s) programm
Arming the systemWhen armed, the perimeter alarm will notify you of an unauthorizedentry. When unauthorized entry occurs, the system will flash the pa
SEATINGAdjustable head restraintsHead restraints help to limit head motion in the event of a rear collision.To properly adjust your head restraints, l
Lift handle to move seat forward orbackward.Pull lever up to adjust seatback.Before returning theseatback to its originalposition, make sure that carg
To adjust the front seatback usingthe manual recliner:• Lift and hold the handle locatedon the side of the seat.• Lean against the seatback toadjust i
Commentaires sur ces manuels