Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 14Entertainment Systems 17AM/FM stereo with CD 17AM/FM stereo with in-dash six
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
When to use the automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in t
Safety belt height adjustmentYour vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shoulder b
If... Then...The driver’s or frontpassenger’s safety belt isbuckled before the ignitionswitch is turned to the ONposition...The safety belt warning li
If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2 minutesh
Reasons given... Consider...“Belts are uncomfortable” We design our safety belts to enhancecomfort. If you are uncomfortable -try different positions
Do not sit on top of a buckled safety belt to avoid theBeltMinder威 chime. Sitting on the safety belt will increase therisk of injury in an accident. T
• Step 3 must be completed within 50 seconds after the safety beltwarning light turns off.3. For the seating position being disabled, at a moderate sp
hardware, should be inspected after a collision. Ford Motor Companyrecommends that all safety belt assemblies in use in vehicles involved ina collisio
Important supplemental restraint system precautionsAirbags DO NOT inflate slowly orgently and the risk of injury from adeploying airbag is greatest cl
Do not attempt to service, repair, or modify the airbagsupplemental restraint system (SRS) or its fuses. See yourauthorized dealer.Modifying or adding
Check engine: The Check Engineindicator light illuminates when theignition is first turned to the ONposition to check the bulb. Solidillumination afte
How does the safety belt pretensioner and airbag supplementalrestraint system work?The safety belt pretensioner andairbag SRS are designed to activate
are not properly restrained or are otherwise out of position at the timeof airbag deployment. Thus, it is extremely important that occupants beproperl
The front passenger sensing system works with sensors that are part ofthe front passenger’s seat and safety belt. The sensors are designed todetect th
• When the front passenger sensing system disables (will not inflate)the front passenger frontal airbag, the indicator lamp will illuminateand stay li
After all occupants have adjusted their seats and put on safety belts, it’svery important that they continue to sit properly. A properly seatedoccupan
• Objects placed on the occupant’s lap• Cargo interference with the seat• Other passengers pushing or pulling on the seat• Rear passenger feet and kne
• If the airbag readiness light remains illuminated, this may or may/notbe a problem due to the front passenger sensing system.DO NOT attempt to repai
Do not use accessory seat covers. The use of accessory seatcovers may prevent the deployment of the side airbags andincrease the risk of injury in an
the collision will be inflated, even if the respective seat is not occupied.The airbag was designed to inflate between the door panel and occupantto f
• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and light are repaired.If any of these things happe
Anti-lock brake system (ifequipped): If the ABS light staysilluminated or continues to flash, amalfunction has been detected, havethe system serviced
Do not attempt to service, repair, or modify the side air curtainsystem, its fuses, the A, B, or C pillar trim, or the headliner on avehicle containin
How does the side air curtain system work?The design and development of theside air curtain system includedrecommended testing proceduresthat were dev
The side air curtain system SRS is designed to activate when the vehiclesustains lateral deceleration sufficient to cause the sensors to close anelect
If any of these things happen, even intermittently, have the SRS servicedat an authorized dealer immediately. Unless serviced, the system may notfunct
neck, the child should wear the lap and shoulder belt. Moving the childcloser to the center of the vehicle may help provide a good shoulder beltfit.Do
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto
Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in acollision.SAFETY SEATS F
and anchors, refer to Attaching safety seats with tether straps in thischapter. For more information of LATCH anchors refer to Attachingsafety seats w
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
Speed control: Illuminates whenthe speed control is engaged. Turnsoff when the speed control systemis disengaged.Door ajar (if equipped):Illuminates w
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a
Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a
4. Open the tether anchor cover.5. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safetyseat may not
Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol.The anchors at the center of ther
If you install a child seat with rigid LATCH attachments, do not tightenthe tether strap enough to lift the child seat off the vehicle seat cushionwhe
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
gauges may be inaccurate. Ford Motor Company recommends the use ofa digital or dial-type tire pressure gauge rather than a stick-type tirepressure gau
To check the pressure in your tire(s):1. Make sure the tires are cool, meaning they are not hot from drivingeven a mile.Note: If you have to drive a d
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them
This begins with the letters “DOT” and indicates that the tire meets allfederal standards. The next two numbers or letters are the plant codedesignati
Never spin the tires in excess of the 35 mph (55 km/h) pointindicated on the speedometer.Highway hazardsNo matter how carefully you drive there’s alwa
• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can be corrected by rotating the tires.Note: If your tir
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
SNOW TIRES AND CHAINSSnow tires must be the same size and grade as the tires youcurrently have on your vehicle.The tires on your vehicle have all weat
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe
VEHICLE LOADINGThis section will guide you in the proper loading of your vehicle to keepyour loaded vehicle weight within its design rating capability
Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment.GAW (Gross Axle Weight) – is the total weight
located on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR.Exceeding the Safety Compliance Certif
Do not exceed the GVWR or the GAWR specified on the SafetyCompliance Certification Label.Do not use replacement tires with lower load carrying capacit
• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the l
Front Wheel Drive (FWD) vehicles:Do not tow your Front Wheel Drive vehicle with the front drive wheelson the ground as transaxle damage may occur. It
STARTINGPositions of the ignition1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and a
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
• Make sure the gearshift is in P(Park).If starting a vehicle with a manualtransmission:• Make sure the parking brake isset.• Push the clutch pedal to
Starting the engine1. Turn the key to 3 (RUN) withoutturning the key to 4 (START).2. Turn the key to 4 (START), thenrelease the key as soon as theengi
Trip odometer: Registers the miles (kilometers) of individual journeys.• Without Message CenterTap on the button to toggle thedisplay between the trip
BRAKESOccasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-o
Using ABSWhen hard braking is required, apply continuous force on the brakepedal; do not pump the brake pedal since this will reduce theeffectiveness
TRACTION ASSIST (IF EQUIPPED)The Traction Assist system helps you maintain the stability andsteerability of your vehicle, especially on slippery road
STEERINGTo prevent damage to the power steering system:• Never hold the steering wheel at its furthest turning points (until itstops) for more than a
If you cannot move the gearshift lever out of P (Park) with ignition inthe RUN position and the brake pedal depressed:1. Apply the parking brake, turn
Understanding the gearshift positions of the 5–speed automatictransaxle (if equipped)P (Park)This position locks the transaxle and prevents the front
N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D
To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)Always set the parking brake full
MANUAL TRANSMISSION OPERATION (IF EQUIPPED)Using the clutchThe manual transaxle has a starter interlock that prevents cranking theengine unless the cl
Reverse1. Make sure that your vehicle is at a complete stop before you shift intoR (Reverse). Failure to do so may damage the transmission.2. Move the
AUDIO SYSTEMSAM/FM Single CD/MP3 sound system (if equipped)Accessory delay: Your vehicle is equipped with accessory delay. Withthis feature, the windo
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
• emergency travel expense reimbursement• travel planning benefitsUsing roadside assistanceComplete the roadside assistance identification card and pl
FUEL PUMP SHUT-OFF SWITCHThis device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt.After an
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 10A Backup lamps, Electrochromaticmirror2
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description12 7.5A Delay accessories: Radio headunits, Moonroof, Lock switchilluminati
Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription6 40A**Rear window defroster, Heated mirrors7 40A** PETA Pump (PZEV engine only)8 — N
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription36 40A** ABS Pump37 — Not used38 — Not used39 — Not used40 — Not used41 — Not used42
CHANGING THE TIRESIf you get a flat tire while driving:• do not brake heavily.• gradually decrease the vehicle’s speed.• hold the steering wheel firml
If your vehicle is not equipped with an in-dash clock, press MENU untilSET HOURS or SET MINUTES appears in the display. Press/ toadjust the hours/minu
• Tow a trailer• Use snow chains on the end of the vehicle with the dissimilar sparetire• Use more than one dissimilar spare tire at a time• Use comme
• Wet weather driving capability• All-Wheel driving capability (if applicable)• Load leveling adjustment (if applicable)When driving with the full-siz
Removing the spare tire and jack1. Remove the carpeted load floorpanel located in the rear of thevehicle and remove the lug wrenchand long bolt from t
2. Remove the center ornament (ifequipped) from the wheel. Looseneach wheel lug nut one-half turncounterclockwise but do not removethem until the whee
7. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torquespecifications later in this chapterfor the proper lu
When a wheel is installed, always remove any corrosion, dirt orforeign materials present on the mounting surfaces of the wheelor the surface of the wh
Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
5. SEEK : Press to access thenext strong station or track.6. Play/Pause: Press to pause a CDthat is playing. PAUSE will appear inthe display. Press ag
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh
authorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of Canada participates in an impartialthird party
GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.
Or call:For a free publication catalog, order toll free: 1-800-782-4356Monday-Friday 8:00 a.m. - 6:00 p.m. ESTHelm, Incorporated can also be reached b
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips.• Always
Seating and Safety Restraints 88Seating 88Safety restraints 93Airbags 107Child restraints 123Tires, Wheels and Loading 135Tire Information 135Vehicle
15. AM/FM: Press to selectAM/FM1/FM2 frequency band.16. ON/OFF/Volume: Press to turnON/OFF. Turn to increase/decreasevolume.If the volume is set above
• 2.3L I4 engine2006 Fusion (fsn)Owners Guide (post-2002-fmt)USA (fus)Cleaning200
• 3.0L DOHC engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTIC (NON-PAINTED) EXT
WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub
INTERIOR TRIM• Clean the interior trim areas with a damp cloth, then with a clean, drycloth; you may also use Motorcraft Dash & Vinyl Cleaner (ZC-
leather conditioners. These products may cause premature wearing ofthe clear, protective coating.Note: In some instances, color or dye transfer can oc
Motorcraft Premium Windshield Washer Concentrate (ZC-32–A)Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54)Motorcraft Spot and
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide sc
2. Block the wheels.• Manual transmission:1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral).2. Block the wheels.Note:
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.3L I4 engine1. Engine coolant reservoir2. Engine oil filler cap3. Engine oil dipstick4. Brake/Clutch
3.0L DOHC V6 Duratec engine1. Engine coolant reservoir2. Power steering fluid reservoir3. Brake fluid reservoir4. Transmission Fluid Dipstick5. Batter
Premium/Audiophile AM/FM In-dash Six CD/MP3 sound system(if equipped)Accessory delay: Your vehicle is equipped with accessory delay. Withthis feature,
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
Poor wiper quality can be improved by cleaning the wiper blades and thewindshield, refer to Windows and wiper blades in the Cleaningchapter.To prolong
• 3.0L DOHC V6 Duratec engine6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.On 2.3L I4 engine, be sure thenotch in the i
• 2.3L I4 engine• 3.0L DOHC V6 Duratec engine•If the oil level is below this mark, engine oil must be added to raisethe level within the normal operat
• 2.3L I4 engine• 3.0L DOHC V6 Duratec engine•Do not overfill the engine with oil. Oil levels above this markmay cause engine damage. If the engine is
5. Fully install the engine oil filler cap by turning the filler cap clockwiseuntil it stops.To avoid possible oil loss, DO NOT operate the vehicle wi
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If
Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyeswhen working near
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
Setting the clock: If your vehicle is equipped with an in-dash clock,refer to Clock in the Driver Controls chapter for instructions on how toset the t
• Add Motorcraft Premium Gold Engine Coolant(yellow-colored), VC-7–A (U.S., except CA, OR and NM),VC-7–B (CA, OR and NM), meeting Ford SpecificationWS
2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly tu
Fill your engine coolant reservoir as outlined in Adding engine coolantin this section.Severe climatesIf you drive in extremely cold climates (less th
• The symbol will illuminate.• Thesymbol will illuminate.If the engine reaches a preset over-temperature condition, the enginewill automatically switc
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsDo not overfill the fuel tank. The pressure in an overfilled tankmay cause leak
• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek med
• Place approved fuel container on the ground.• DO NOT fill a fuel container while it is in the vehicle (including thecargo area).• Keep the fuel pump
If you do not use the proper fuel filler cap, excessive pressure orvacuum in the fuel tank may damage the fuel system or causethe fuel cap to disengag
Do not be concerned if your engine sometimes knocks lightly. However, ifit knocks heavily under most driving conditions while you are using fuelwith t
possible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel economy. We do not recommendtaking fuel econ
Track/Folder Mode: Available only on MP3 discs in CD mode.Press/ to toggle between Track and Folder mode.In Track Mode, pressSEEK to scroll through al
3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading.4. Subtract your initial odometer reading fro
• Resting your foot on the brake pedal while driving may reduce fueleconomy.• Combine errands and minimize stop-and-go driving.Maintenance• Keep tires
EMISSION CONTROL SYSTEMYour vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to co
Please consult your Warranty Guide for complete emission warrantyinformation.On board diagnostics (OBD-II)Your vehicle is equipped with a computer tha
• Next, at least 20 minutes driving in stop-and-go, city-type traffic withat least four idle periods.Allow the vehicle to sit for at least eight hours
1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gauge indicator will benear the center
operated for an extended period at high speeds, in city trafficduring hot weather or pulling a trailer, the vehicle should beturned off for about 30 m
High fluid levelFluid levels above the safe rangemay result in transaxle failure. Anoverfill condition of transmissionfluid may cause shift and/orenga
Checking automatic transmission fluid at normal operatingtemperature (140°F-158°F [60°C-70°C])Automatic transmission fluid expands when warmed. To obt
Low fluid levelDo not drive the vehicle if the fluidlevel does not show at all on thedipstick.Driving the vehicle with less thanthe recommended fluid
press and hold a preset button until sound returns. You can store up to18 stations, six in AM, six in FM1 and six in FM2.13. TEXT/SCAN: Press and hold
Checking and adding manual transmission fluid (if equipped)1. Park the vehicle on a levelsurface.2. Engage the parking brake fully –put in first gear.
Changing the air filter element• 2.3L I4 engine• 3.0L DOHC V6 Duratec engine1. Release the clamps that secure the air filter housing cover.2. Carefull
• 3.0L DOHC V6 Duratec engine3. Remove the air filter element from the air filter housing.4. Wipe the air filter housing and cover clean to remove any
Replace the PCV valve with one that meets Ford material anddesign specifications for your vehicle, such as a Motorcraft orequivalent replacement part.
Fluid Ford PartNameApplication CapacityPower steeringfluidMotorcraftMERCON威 ATFAll Between MINand MAX onreservoirEngine coolant2MotorcraftPremium Gold
4Indicates only approximate dry-fill capacity. Some applications may varybased on cooler size and if equipped with an in-tank cooler. The amountof tra
Item Ford partnameFord partnumberFordspecificationLock cylinders MotorcraftPenetrating andLock LubricantXL-1 nonePower steeringfluidMotorcraftMERCON威
VEHICLE DIMENSIONSVehicle dimensions Inches (mm)(1) Overall length 191.4 (4832)(2) Overall width 72.2 (1835)(3) Overall height 55.8 (1417)(4) Wheelbas
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel.Please
18. LOAD: Press to load a CD.Press LOAD and a memory presetto load to a specific slot. Press andhold to autoload up to six CDs.19. CD eject:Press to e
TRANSMISSION/TRANSAXLE CODE DESIGNATIONSYou can find atransmission/transaxle code on theSafety Compliance CertificationLabel. The following table tell
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford
Interior styleElectrochromatic compass/temperature interior mirrorsFloor matsScuff platesLifestyleBike racksCargo organization and managementPeace of
• To avoid interference with other vehicle functions, such as anti-lockbraking systems, amateur radio users who install radios and antennasonto their
AAccessory delay ...53Air cleaner filter ...240–242Air conditioning ...29, 31Airbag supplemental r
Climate control (see Airconditioning or Heating) ...29, 31Clock ...51Clock adjust6-CD in dash ...
FFail safe cooling ...222Fluid capacities ...243Foglamps ...36Fuel ...
LLampsautolamp system ...35bulb replacementspecifications chart ...40daytime running light ...36fog lam
Safety belts (seeSafety restraints) ...93, 97–101Safety defects, reporting ...197Safety restraints ...93, 97–101belt minder ...
Vehicle Identification Number(VIN) ...249Vehicle loading ...150Ventilating your vehicle
CD units are designed to play commercially pressed 4.75 in (12 cm)audio compact discs only. Due to technical incompatibility, certainrecordable and re
260
261
262
263
264
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
6. Fan speed adjustment: Controls the volume of air circulated in thevehicle.Manual heating and air conditioning system operating tips• To reduce fog
Do not place objects on top of the instrument panel as theseobjects may become projectiles in a collision or sudden stop.AUTOMATIC TEMPERATURE CONTROL
Maintenance and Specifications 206Engine compartment 208Engine oil 211Battery 216Engine Coolant 218Fuel information 224Air filter(s) 241Part numbers 2
4. Recirculation control: Press to activate/deactivate airrecirculation in cabin. Recirculated air may reduce the amount of time tocool down the inter
Automatic Temperature Control (ATC) system with heated seats(if equipped)Temperature conversion: To switch between Fahrenheit and Celsius:If your vehi
passenger heated seat. Note: The passenger heated seat will turn offautomatically after 15 minutes of use.5.: Distributes air through the windshield d
Automatic Temperature Control (ATC) system operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector i
• To aid in side window defogging/demisting in cold weather:1. Select.2. Select A/C.3. Adjust the temperature control to maintain comfort.4. Set the f
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola
5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamp switch to. The headlampswill turn off.Fogl
High beamsPush the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate.Flash to passPull toward you slightly to acti
Vertical aim adjustment1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away.• (1) 8 fe
TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSDome lamps and map lampsThe ma
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an
Replacing headlamp bulbsHighbeam bulb (lower) replacement1. Make sure headlamp switch is in the OFF position, then open thehood.2. Reach over the fron
7. For ease of bulb socket installation into the lamp assembly, hold thebulb socket at 15 degrees clockwise from a vertical position. Using the 2lead
4. Remove screw from oval splashshield access panel from theexterior wheel well area. Lift up andrearward to release a hidden fingerattachment at the
Handle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and donot touch the glass. The oil f
3. Remove screw from oval splashshield access panel from theexterior wheel well area. Lift up andrearward to release a hidden fingerattachment at the
Replacing front side marker bulbs1. Make sure the headlamp controlis in the OFF position.2. Pry the lamp away from thevehicle at the rear of lamp at t
1. Remove the bulb by turning itcounterclockwise and pulling itstraight out.2. Pull the bulb from the socket andpush in the new bulb.3. Install the bu
Replacing foglamp bulbs (if equipped)1. Make sure the foglamp switch isin the OFF position.2. From underneath the vehicle,partially remove the tire sp
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
TILT/TELESCOPE STEERING WHEELTo adjust the steering wheel:1. Pull the lever down to unlock thesteering column.2. While the lever is in the downpositio
Storage compartmentPress the latch to open the storagecompartment.The storage compartment may beused to secure sunglasses or asimilar object.CLOCK (IF
INSTRUMENT PANEL STORAGE COMPARTMENTThe storage compartment may beused to secure sunglasses or similarsized objects. Press the control toopen the stor
POWER WINDOWSDo not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injurethemselves.W
Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controlsexcept for the driver’s press
Heated mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not remove ice
3. Press the SET + control andrelease it.4. Take your foot off the acceleratorpedal.5. The indicatorlight on theinstrument cluster will turn on.Note:•
Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET + controluntil you get to the desiredspeed,
Turning off speed controlThere are two ways to turn off the speed control:• Press the speed control OFFcontrol.• Turn OFF the ignition.Note: When you
In any mode:• Press VOL + or - to adjust thevolume.Climate control featuresPress TEMP + or - to adjusttemperature.Press FAN + or - to adjust fanspeed.
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental restraint
To open the moon roof:The moon roof is equipped with anautomatic, one-touch, expressopening, closing and venting feature.Press and release the rear po
MESSAGE CENTER (IF EQUIPPED)With the ignition in the RUNposition, the message center,located on your instrument cluster,displays important vehicleinfo
Distance to empty (DTE)Selecting this function from theINFO menu estimates approximatelyhow far you can drive with the fuelremaining in your tank unde
Average SpeedSelect this function from the INFO menu to display AVERAGE SPEEDand press the RESET control. Your average speed from that point will bedi
4. Determine your magnetic zone byreferring to the zone map.5. Press and hold the RESET untilthe message center display changesto show the current zon
Trip elapsed drive timeSelect this function from the INFOmenu to display a timer.To operate the Trip Elapsed DriveTime perform the following:1. Press
Units (English/Metric)1. Select this function from theSETUP menu for the current unitsto be displayed.2. Press the RESET control tochange from English
This acts as a reminder that these warning conditions still exist withinthe vehicle.Warnings StatusDriver door ajar Warning cannot be reset (PLEASECLO
CHECK BRAKE SYSTEM. Displayed when the brake system needsservicing. If the warning stays on or continues to come on, contact yourauthorized dealer as
KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the lo
authority. Other parties may seek to access the informationindependently of Ford Motor Company and Ford of Canada.Cell phone useThe use of Mobile Comm
Note: Your vehicle’s IKTs wereissued with an adhesive securitylabel on them that providesimportant vehicle key cutinformation. It is recommended thaty
Likewise, when rotating the IKT tothe 1 (LOCK) position in theignition lock cylinder, the bottomedge of the IKT adjacent to thecontrol can be utilized
• Remote entry transmitter portion of your Integrated KeyheadTransmitter, or• Driver power door lock control (Note: The driver’s door must beopen, the
CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the
To open the luggage compartmentdoor (lid) from within the luggagecompartment, pull the illuminated“T” shaped handle and push up onthe trunk lid. The h
Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment.The typ
Unlocking the doors/two stage unlock1. Press and release to unlock the driver’s door. Note: The interiorlamps will illuminate.2. Pressand release agai
Replacing the batteryThe Integrated Keyhead Transmitter uses one coin type three-voltlithium battery CR2032 or equivalent.To replace the battery:1. Tw
Illuminated entryThe interior lamps and puddle lamps (if equipped) illuminate when theIntegrated Keyhead Transmitter is used to unlock the door(s).The
1. Place the key in the ignition andturn the ignition to the 3 (RUN)position.2. Press the power door unlockcontrol on the door panel threetimes.3. Tur
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
Autolock featureThe autolock feature will lock all the doors when:• all the doors are closed,• the ignition is in the 3 (RUN) position,• you shift int
or the procedure will have to be repeated. If the procedure needs to berepeated, wait a minimum of 30 seconds before beginning again.1. Place the key
1. Place the key in the ignition andturn the ignition to the 3 (RUN)position.2. Press the power door unlockcontrol on the door panel threetimes.3. Tur
objects from touching the coded IKT while starting the engine. Theseobjects will not cause damage to the coded IKT, but may cause amomentary issue if
keyless entry transmitter. A maximum of eight coded keys can beprogrammed to your vehicle; only four of these eight keys can be IKTswith remote entry
3. Turn the ignition to the 1 (LOCK) position and remove the first codedkey from the ignition.4. Within ten seconds of turning the ignition to the 1 (
The system is ready to arm whenever the key is in the 1(LOCK)position, or is removed from the ignition. Either of the following actionswill prearm the
Triggering the anti-theft systemThe armed system will be triggered if:• Any door, the hood or the trunk is opened without using the door keyor the rem
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Using the manual lumbar support (if equipped)The lumbar control is located on theside of the seat cushion.Turn to adjust lumbar support.Adjusting the
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
Pull lever up to adjust seatback.Pump the handle upwards to raisethe cushion and pump downward tolower the cushion to the desiredlocation.Adjusting th
Sitting improperly out of position or with the seat back reclinedtoo far can take off weight from the seat cushion and affect thedecision of the front
Heated seats (if equipped)The heated seat control is located on the climate control system. Referto the Climate controls chapter.REAR SEATSSplit-foldi
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback.After returning the sea
• Driver’s seat position sensor.• Front passenger sensing system• “Passenger airbag off” or “pass airbag off” indicator lamp• Front crash severity sen
allows your Personal Safety System娂 to distinguish between differentlevels of crash severity and modify the deployment strategy of thedual-stage airba
Front safety belt usage sensorsThe front safety belt usage sensors detect whether or not the driver andfront outboard passenger safety belts are faste
If any of these things happen, even intermittently, have the PersonalSafety System娂 serviced at an authorized dealer immediately. Unlessserviced, the
Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.Combination lap and shoulder bel
Failure to inspect and replace if necessary the Belt andRetractor assembly after an accident could increase the risk ofinjury in a collision.All safet
Commentaires sur ces manuels