Ford 2006 F-150 v.2 Manuel d'utilisateur

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 19Entertainment Systems 22AM/FM stereo 22AM/FM stereo with CD 24AM/FM stereo cas

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta key.• activate the personal alarm.If there are problems with the remote

The (lock) and (unlock) features will work again after:• a door has become ajar,• the ignition is turned to the 3 (ON) position, or• using the UNLOCKc

2. Press the SET control on thedriver’s seat.3. Within 5 five seconds, press onecontrol on the remote transmitterand then press the 1 or 2 control ont

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery. Note: Please refer to local r

To program the transmitters yourself:• Unlock all doors using the powerdoor lock/unlock control. Insert akey and turn the ignition fromthe 1 (OFF/LOCK

• any door is open.The battery saver will shut off the interior lamps 30 minutes after thelast door is closed, even if the dimmer control is on.Perime

Every two consecutive presses of the control after successfullyentering the configuration mode will change the enable/disable conditionof the feature.

Power door unlock/lock procedureYou must complete Steps 1–5 within30 seconds, or the procedure willhave to be repeated. If theprocedure needs to be re

KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to:• lock all vehicle doors.• unlock only the driver’s door.• unlock all vehicle

4. After the code is entered, the locks will cycle, confirming that the newcode has been set.Tips:• Do not set a code that uses five of the same numbe

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

Note: The SecuriLock娂 passive anti-theft system is not compatible withnon-Ford aftermarket remote start systems. Use of these systems mayresult in veh

Replacement keysIf your keys are lost or stolen and you don’t have an extra coded key,you will need to have your vehicle towed to an authorized dealer

5. Within 10 seconds of removing the second coded key, insert the newunprogrammed key (new key/valet key) into the ignition and turn theignition from

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

Push control to lower head restraint.Front seat• Lift the track release bar to movethe seat forward or rearward.Make sure that the seat isrelatched in

Using the armrest (if equipped)Push the release control to movethe armrest up or down.Using the manual lumbar supportFor more lumbar support, turn the

Sitting improperly out of position or with the seat back reclinedtoo far can take off weight from the seat cushion and affect thedecision of the passe

Memory seats/adjustable pedals (if equipped)This system allows automaticpositioning of the driver seat andadjustable pedals to twoprogrammable positio

The head restraints can be movedup and down. Lift the head restraintso that it is located directly or asclose as possible behind your head.Push contro

Returning the seat to seating positionBefore returning the seatback to its original position, make surethat cargo or any objects are not trapped under

WARNING LIGHTS AND CHIMESBase instrument clusterBase with Tachometer instrument cluster2006 F-150 (f12)Owners Guide (post-2002-fmt)USA (fus)Instrument

How does the Personal Safety System姟 work?The Personal Safety System娂 can adapt the deployment strategy of yourvehicle’s safety devices according to c

Front passenger sensing systemFor airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occu

Front outboard safety belt pretensionersThe front seat outboard safety belt pretensioners are designed to tightenthe safety belts firmly against the o

Safety restraints precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injur

Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Checkseat covers and buckle

If you carry large cargo behind the seat or items that might damage orsoil the belt, detach the belt from the seat:1. Release the mini-buckle byinsert

2. Buckle the small tongue on theend of the belt into the mini-buckleon the driver’s side. The belt is nowready for use. This mini-buckleshould stay b

3. Insert the belt tongue into the proper buckle for your seating positionuntil you hear a snap and feel it latch.4. Make sure the tongue is securely

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ

The front and rear safety restraints in the vehicle are combination lapand shoulder belts. The front passenger outboard and rear outboard seatsafety b

Family carrier instrument clusterMid instrument cluster2006 F-150 (f12)Owners Guide (post-2002-fmt)USA (fus)Instrument Cluster13

How to use the automatic locking mode1. Buckle the combination lap and shoulder belt.• Right front passenger seat• Rear seats (if equipped)2. Grasp th

How to disengage the automatic locking modeDisconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic l

Safety belt usage sensorsThe driver and front outboard passenger safety belt buckles areequipped with sensors that detect if the safety belts are fast

Safety belt extension assemblyIf the safety belt is too short when fully extended, there isa8inch(20 cm) safety belt extension assembly that can be ad

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war

If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2 minutesh

Reasons given... Consider...“Belts are uncomfortable” We design our safety belts to enhancecomfort. If you are uncomfortable -try different positions

Do not sit on top of a buckled safety belt to avoid the BeltMinder chime. Sitting on the safety belt will increase the risk ofinjury in an accident. T

• After Step 3, the restraint system warning light (airbag light) will beturned on for three seconds.4. Within 10 seconds of the light turning on, buc

• Front passenger sensing system• Passenger airbag off indicator light.The airbag supplemental restraints are an integral part of the PersonalSafety S

Luxury instrument clusterHarley-Davidson instrument clusterWarning lights and gauges can alert you to a vehicle condition that maybecome serious enoug

To properly position yourself away from the airbag:• Move your seat to the rear as far as you can while still reaching thepedals comfortably.• Recline

Children and airbagsFor additional important safetyinformation, read all information onsafety restraints in this guide.Children must always be properl

How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustainssufficient longitudinal decelera

If the airbag has deployed, the airbag will not function againand must be replaced immediately. If the airbag is notreplaced, the unrepaired area will

The front passenger sensing system will disable (will not inflate) thefront passenger’s frontal airbag if:• the front passenger seat is unoccupied, or

• When the front passenger sensing system enables the front passengerfrontal airbag (may inflate), the indicator will be unlit and stay unlit.If a per

The front passenger sensing system may detect small or medium objectsplaced on the seat cushion. For most objects that are in the frontpassenger seat,

SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme

Child booster seatsChildren outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the la

Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi

Service engine soon: The Serviceengine soon indicator lightilluminates when the ignition is firstturned to the ON position to checkthe bulb. Solid ill

Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in acollision.SAFETY SEATS F

• LATCH lower anchors are recommended for use by children up to22 kg (48 pounds) in a child restraint. Top tether anchors can be usedfor children up t

1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear

8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly move the seat forwardand back to m

2. If the center lap/shoulder safetybelt has been disconnected from theseat to carry large cargo behind theseat, reconnect it by buckling thesmall buc

5. Insert the belt tongue into theproper buckle for that seatingpositions until you hear a snap andfeel it latch. Make sure the tongue issecurely latc

9. Check from time to time to be sure that there is no slack in thelap/shoulder belt. The shoulder belt must be snug to keep the lap belttight during

The passenger seats of your vehicle are equipped with built-in tetherstrap anchors located behind the seats as described below.The tether anchors in y

Mid and Luxury instrumentclusterIf the brake system warning lightdoes not illuminate at this time,seek service immediately from yourauthorized dealer.

• You may need to pull the seatback forward to access the tetheranchors. Make sure the seatback is locked in the upright positionbefore installing the

If the safety seat is not anchored properly, the risk of a childbeing injured in a collision greatly increases.Rear seat tether strap attachmentThere

2. Route the tether strap behind thehead restraint supports to a loopbehind an adjacent seating position,and hook the strap hook onto theloop. If usin

Your vehicle is equipped with LATCH anchors for child seat installationat the following seating positions (LATCH is not available on F150Regular cab)

If you install a child seat with rigid LATCH attachments, do not tightenthe tether strap enough to lift the child seat off the vehicle seat cushionwhe

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary.

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

Glossary of tire terminology• Tire label: A label showing the OE (Original Equipment) tire sizes,recommended inflation pressure and the maximum weight

Door ajar: Illuminates when theignition is in the ON position andany door is open.Overdrive off (if equipped):Illuminates when the overdrivefunction o

Every day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires and adjust ifrequired.A

higher than the manufacturer’s recommended cold inflation pressurewhich can be found on the Safety Compliance Certification Label or TireLabel which i

6. Visually inspect the tires to make sure there are no nails or otherobjects embedded that could poke a hole in the tire and cause an airleak.7. Chec

AgeTires degrade over time, even when they are not being used. It isrecommended that tires generally be replaced after 6 years of normalservice. Heat

It is recommended that the two front tires or two rear tires generally bereplaced as a pair.Safety practicesDriving habits have a great deal to do wit

Front wheel drive (FWD) vehicles and those with an independent rearsuspension (if equipped) may require alignment of all four wheels.The tires should

Note: After having your tires rotated, inflation pressure must be checkedand adjusted to the vehicle requirements.INFORMATION CONTAINED ON THE TIRE SI

Note: You may not find this information on all tires because it is notrequired by federal law.7. H: Indicates the tire’s speed rating. The speed ratin

9. M+S or M/S: Mud and Snow, orAT: All Terrain, orAS: All Season.10. Tire Ply Composition and Material Used: Indicates the number ofplies or the numbe

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

MINI MESSAGE CENTER WARNING DISPLAYS (IF EQUIPPED)Door ajar: Displays when theignition is in the ON position andany door is open.Low fuel: Displays wh

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

SNOW TIRES AND CHAINSSnow tires must be the same size and grade as the tires youcurrently have on your vehicle.The tires on your vehicle have all weat

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).

Maximum Loaded Trailer Weight – is the highest possible weight of afully loaded trailer the vehicle can tow. It assumes a vehicle with onlymandatory o

5. Determine the combined weight of luggage and cargo being loaded onthe vehicle. That weight may not safely exceed the available cargo andluggage loa

Special loading instructions for owners of pickup trucks andutility-type vehiclesFor important information regarding safe operation of this typeof veh

Regular Cab 4x2 (126” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)4.2L (withmanualtransmission)3.31 7200 (3266)

GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera

Regular Cab 4x4 (126” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)4.6L 3.55 11500 (5216) 6300 (2857)4.6L 3.73 12

SuperCab 4x2 (132.5” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)4.6L (with 17”tires)3.55 11500 (5216) 6300 (285

SuperCab 4x2 (144.5” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)5.4L (with 18”or 20” tires)3.55 13500 (6123) 81

SuperCab 4x4 (132.5” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)5.4L (with 17”tires)3.55 13000 (5897) 7400 (335

Super Cab 4x4 (144.5” wheelbase) Harley-Davidson Version(not available for F-150 Lobo)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-

Crew Cab 4x4 (138.5” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)4.6L (with 17”tires)3.73 12200 (5534) 6500 (294

Crew Cab 4x4 (150.5” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)4.6L (with 17”tires)3.73 12200 (5534) 6400 (290

Load equalizing hitchWhen hooking up a trailer using a load equalizing hitch, always use thefollowing procedure:1. Park the unloaded vehicle on a leve

Using a step bumper (if equipped)The rear bumper is equipped with an integral hitch and only requires aball with a one inch (25.4 mm) shank diameter.

• After you have traveled 50 miles (80 km), thoroughly check yourhitch, electrical connections and trailer wheel lug nuts.• To aid in engine/transmiss

Seating and Safety Restraints 113Seating 113Safety restraints 119Airbags 138Child restraints 147Tires, Wheels and Loading 165Tire Information 167Tire

Odometer: Registers the total miles (kilometers) of the vehicle.• With Mini Message Center• With Full Message CenterRefer to Message Center in theDriv

• The vehicle must be towed in the forward position to ensure nodamage is done to the internal transfer case components.The transfer case N (Neutral)

STARTINGPositions of the ignition1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval.Note: The ignition

Do not start your vehicle in a closed garage or in other enclosedareas. Exhaust fumes can be toxic. Always open the garage doorbefore you start the en

• Make sure the parking brake isset.If starting a vehicle with a manual transmission:• Make sure the parking brake isset.• Push the clutch pedal to th

Starting the engine1. Turn the key to 3 (ON) withoutturning the key to 4 (START). Ifthere is difficulty in turning the key,rotate the steering wheel u

If the engine fails to start using the preceding instructions(flexible fuel vehicles only)1. Press and hold down the accelerator 1/3 to 1/2 way to flo

Base instrument cluster withand without tachometerMid and Luxury instrumentclusterFour-wheel anti-lock brake system (ABS)Your vehicle is equipped with

Base instrument cluster withand without tachometerMid and Luxury instrumentclusterParking brakeTo set the parking brake (1), pressthe parking brake pe

TRACTION CONTROL姟 (IF EQUIPPED)Your vehicle may be equipped with a Traction Control娂 system. Thissystem helps you maintain the stability and steerabil

STEERINGTo help prevent damage to the power steering system:• Never hold the steering wheel at its furthest turning points (until itstops) for more th

Engine oil pressure gauge:Indicates engine oil pressure. Theneedle should stay in the normaloperating range (between “L” and“H”). If the needle falls

PREPARING TO DRIVEUtility vehicles have a significantly higher rollover rate thanother types of vehicles.In a rollover crash, an unbelted person is si

2. Locate the round access plug onthe underside of the steeringcolumn cover.3. Remove the access plug using a flat head screwdriver, then push theover

2. Open the center console bin.Using a screwdriver, carefully pry offthe console finish panel surroundingthe shifter mechanism by inserting ascrewdriv

If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly.See your authorized deal

To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)Always set the parking brake full

• Floor-shift transmissionThe transmission control indicator(TCIL) will illuminate on theinstrument cluster.Drive (not shown)Drive is activated when t

• Allows upshifts by moving gearshift lever.• Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds

During each shift, the clutch pedal must be fully depressed to the floor.Failure to fully depress the clutch pedal to the floor may cause increasedshi

Maximum downshift speeds14 - 3 45 mph (72 km/h) 17 mph (27 km/h)3 - 2 35 mph (56 km/h) 13 mph (21 km/h)2 - 1 20 mph (32 km/h) 7 mph (11 km/h)1Downshif

To help avoid personal injury, always use caution when inreverse and when using the RSS.This system is not designed to prevent contact with small ormo

AUDIO SYSTEMSAM/FM Stereo System (if equipped)1./ Tune: Press to manuallygo up or down the radio frequency.Also use in menu mode to selectvarious sett

The RSS automatically turns onwhen the gearshift lever is placed inR (Reverse) and the ignition is ON.An RSS control allows the driver toturn the RSS

• 4X4 LOW – Momentarilyilluminates when the engine isstarted. Illuminates when 4L isselected.Using a manual 4WD system (if equipped)2H (2WD High) – Po

3. Place the transmission in N (Neutral).4. Move the transfer case lever through N (Neutral) directly to thedesired position.• If the transfer case wi

4L (4WD Low) - Uses extra gearing to provide maximum power to allfour wheels at reduced speeds. Intended only for off-road applicationssuch as deep sa

AWD (Auto) - Power delivered to all four wheels, as required, forincreased traction. This is appropriate for all on-road driving conditions,such as dr

steering and braking control of your vehicle, you must have all fourwheels on the ground and they must be rolling, not sliding or spinning.Basic opera

Do not rock the vehicle if the engine is not at normal operatingtemperature or damage to the transmission may occur.Do not rock the vehicle for more t

the driveline. Therefore, the vehicle is free to roll even if the automatictransmission is in P (Park) or the manual transmission is in gear. Do notle

Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required f

Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should

Setting the clock: Press until HR or Mn is displayed.Press/ / SEEK to adjust the hours/minutes.3. Seek: Press to access thenext/previous strong statio

Driving on snow and ice4WD vehicles have advantages over 2WD vehicles in snow and ice butcan skid like any other vehicle.Should you start to slide whi

DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th

• The Total Accessory Reserve Capacity (TARC) is shown on the lowerright side of the vehicle’s Safety Certification Label. This is the weightof perman

Snowplowing with your air bag equipped vehicleYour vehicle is equipped with a driver and passenger air bagSupplemental Restraint System (SRS) The SRS

Engine temperature while plowingWhen driving with a plow, your engine may run at a higher temperaturethan normal because the attached snowplow blade w

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

Canadian customers refer to your Owner Information Guide forinformation on:• coverage period• exact fuel amounts• towing of your disabled vehicle• eme

HAZARD FLASHERThe hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is

This switch is located in the frontpassenger’s footwell, behind the kickpanel access cover, to the left of thefuse box. The access cover needs tobe re

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

AM/FM Stereo Single CD/Satellite Compatible Sound System(if equipped)AM/FM Stereo Single CD with MP3/Satellite Compatible SoundSystem (late availabili

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 10A* Run/Accessory - Wipers,Instrument clu

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description8 10A* Heated mirrors, Switch indicator9 20A* Fuel pump relay, Fuel injecto

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description24 15A* Battery saver power for demandlamps25 10A* LH low beam headlamp26 2

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description41 20A* Cigar lighter, Diagnostic connectorpower42 10A* Trailer tow left tu

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionR202 Half ISO relay Fog lampsR203 Half ISO relay PCM* Mini fuses ** Cartrid

Fuse/RelayLocationFuse AmpRatingDescriptionR02 Full ISORelay4x4 CWR031⁄2ISORelayDaytime Running Lamps (DRL) high beamdisableR201 Relay DRLR202 Relay A

When driving with one of the dissimilar spare tires listed above, do not:• Exceed 50 mph (80 km/h)• Load the vehicle beyond maximum vehicle load ratin

• Winter weather driving capability• Wet weather driving capability• All-Wheel driving capability (if applicable)• Load leveling adjustment (if applic

2. Fully insert the jack handlethrough the bumper hole and intothe guide tube through the accesshole in the rear bumper.3. Turn the handle countercloc

3. Block the diagonally oppositewheel.4. Obtain the spare tire and jackfrom their storage locations.5. Use the tip of the lug wrench toremove any whee

1. / Tune: In radio mode,press to manually go up ()ordown () the radio frequency.In menu mode, use to select varioussettings.In Satellite Radio mode (

• RearTo lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engine when yourve

• Seven lug nut wheel12. Stow the flat tire. Refer to Stowing the flat/spare tire.13. Stow the jack and lug wrench. Make sure the jack is fastened so

6. If removed, install the spare tire lock (if equipped) into the bumperdrive tube with the spare tire lock key (if equipped) and jack handle.WHEEL LU

Preparing your vehicleWhen the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, th

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling

BASS: Press MENU until BASS appears in the display. Use / /SEEK to adjust the bass levels.BAL (Balance): Press MENU until BAL appears in the display.U

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh

authorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of Canada participates in an impartialthird party

GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.

For a free publication catalog, order toll free: 1-800-782-4356Monday-Friday 8:00 a.m. - 6:00 p.m. ESTHelm, Incorporated can also be reached by their

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

WAXINGApplying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage.• Wash the ve

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

• 4.6L engine• 5.4L engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTIC (NON-PAIN

5. Seek: In radio mode, press/ to access theprevious/next strong station.In CD mode, press/ toaccess the previous/next CD track.In Satellite Radio mod

• For plastic headlamp lenses, use Motorcraft Ultra Clear Spray GlassCleaner (ZC-23).WINDOWS AND WIPER BLADESThe windshield, rear and side windows and

INSTRUMENT PANEL AND CONSOLE(HARLEY-DAVIDSON F150 ONLY)Your Harley-Davidson F150 instrument panel and console is uniquelypainted with both high and lo

INTERIOR TRIM• Clean the interior trim areas with a damp cloth, then with a clean, drycloth; you may also use Motorcraft Dash & Vinyl Cleaner (ZC-

Leather seats for the King Ranch SuperCrew only (if equipped)Your vehicle is equipped with seating covered in premium, top-grainleather which is extre

ConditioningBottles of King Ranch Leather Conditioner are available at the KingRanch Saddle Shop. Visit the Web site at www.krsaddleshop.com,ortelepho

Motorcraft Detail Wash (ZC-3–A)Motorcraft Dusting Cloth (ZC-24)Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20)Motorcraft Engine Shampoo (C

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide sc

• Manual transmission:1. Set the parking brake, depress the clutch and place the gearshift inN (Neutral).2. Block the wheels.To reduce the risk of veh

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.2L V6 engine1. Battery2. Clutch fluid reservoir (manual transmission)3. Power steering fluid reservo

4.6L V81. Battery2. Transmission fluid dipstick (automatic transmission)3. Engine oil filler cap4. Power steering fluid reservoir5. Engine oil dipstic

FOLDER: press to access theprevious folder on MP3 discs, iffolders are available.10. Fast forward: Press tomanually advance in a CD track.11. Rewind:

5.4L V81. Battery2. Transmission fluid dipstick (automatic transmission)3. Air filter assembly4. Power steering fluid reservoir5. Engine oil dipstick6

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

Poor wiper quality can be improved by cleaning the wiper blades and thewindshield, refer to Windows and wiper blades in the Cleaningchapter.To prolong

• 4.2L V6 engine• 4.6L/5.4L V8 engine5. Locate and carefully remove the engine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the

• If the oil level is between the lower and upper holes or betweenthe MIN and MAX marks (depending on application), the oillevel is acceptable. DO NOT

4. Install the indicator and ensure it is fully seated.5. Fully install the engine oil filler cap by turning the filler cap clockwise1/4 of a turn unt

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If

Battery posts, terminals and related accessories contain lead andlead compounds. Wash hands after handling.Because your vehicle’s engine is also elect

ENGINE COOLANTChecking engine coolantThe concentration and level of engine coolant should be checked at theintervals listed in scheduled maintenance i

• Refer to scheduled maintenance information for service intervalschedules.• Be sure to read and understand Precautions when servicing yourvehicle in

In Satellite radio mode (if equipped), press and release to enter TEXTMODE and display the current song title. While in TEXT MODE, pressagain to scrol

• A large amount of water without engine coolant may be added, in caseof emergency, to reach a vehicle service location. In this instance, thecooling

Whenever coolant has been added, the coolant level in the coolantreservoir should be checked the next few times you drive the vehicle. Ifnecessary, ad

If you drive in extremely hot climates:• It is still necessary to maintain the coolant concentrationabove 40%.• NEVER decrease the coolant concentrati

When this occurs the vehicle will still operate. However:• The engine power will be limited.• The air conditioning system will be disabled.Continued o

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsDo not overfill the fuel tank. The pressure in an overfilled tankmay cause leak

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek med

Flexible fuel components and standard unleaded gasoline fuelcomponents are not interchangeable. If your vehicle is notserviced in accordance with flex

Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1/4 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref

If you do not use the proper fuel filler cap, excessive vacuum inthe fuel tank may damage the fuel system or cause the fuel capto disengage in a colli

Octane recommendationsDo not be concerned if your enginesometimes knocks lightly. However,if it knocks heavily under mostdriving conditions while you

Maintenance and Specifications 276Engine compartment 278Engine oil 282Battery 286Engine Coolant 288Fuel information 294Air filter(s) 312Part numbers 3

AM/FM Single CD/Cassette/Satellite Compatible Sound System(if equipped)1./ Tune: In radio mode,press to manually go up ( )ordown () the radio frequenc

FFV engine (if equipped)Your FFV will operate well on ordinary “Regular” unleaded gasoline, butonly the highest quality fuel ethanol will provide the

The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fu

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fuelecon

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled mainten

applicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproperly:• Use o

Please consult your Warranty Guide for complete emission warrantyinformation.On board diagnostics (OBD-II)Your vehicle is equipped with a computer tha

• Next, at least 20 minutes driving in stop-and-go, city-type traffic withat least four idle periods.Allow the vehicle to sit for at least eight hours

CLUTCH FLUID (IF EQUIPPED)Check the fluid level. Refer to scheduled maintenance information forthe service interval schedules.During normal operation,

TRANSMISSION FLUIDChecking automatic transmission fluid (if equipped)Refer to your scheduled maintenance information for scheduledintervals for fluid

You can check the fluid without driving if the ambient temperature isabove 50°F (10°C). However, if fluid is added at this time, an overfillcondition

2. Seek: In radio mode, press/ to access theprevious/next strong station.In CD mode, press/ toaccess the previous/next CD track.In Satellite Radio mod

If an overfill occurs, excess fluidshould be removed by an authorizeddealer.An overfill condition oftransmission fluid may causeshift and/or engagemen

3. Fluid level should be at bottom ofthe opening.4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening.

3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening.Use only fluid that meets Ford specifications

Changing the air filter element• 4.2L/4.6L engines1. Loosen the clamp that securesthe air filter element in place.2. Carefully separate the two halves

• 5.4L Engine1. Release two retainer clamps.2. Pull air filter tray assembly outtoward front of vehicle and lift airfilter element up and out of housi

MOTORCRAFT PART NUMBERSComponent 4.2L V6 engine 4.6L V8 engine 5.4L V8engineAir filter element FA-1632 FA-1632 FA-1754Battery BTX-65-650 orBTX-593BTX-

REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluidand clutchfluidMotorcraftHighPerformanceDOT 3MotorVehicleBrake FluidAll Fill to lin

Fluid Ford PartNameApplication CapacityPowersteeringfluidMotorcraftMERCON威ATFAll Fill to between MINand MAX lines onreservoirTransfercase fluidMotorcr

in an automatic transmission that requires use of the MERCON威 typefluid. However, these dual usage fluids may be used in transmissions thatrequire the

LUBRICANT SPECIFICATIONSItemFord partname orequivalentFord partnumberFordspecificationFront axle(4X4)Motorcraft SAE80W-90Premium RearAxle LubricantXY-

BASS: Press MENU until BASS appears in the display. Use / /SEEK to adjust the bass levels.BAL (Balance): Press MENU until BAL appears in the display.U

ItemFord partname orequivalentFord partnumberFordspecificationHinges, latches,striker plates,fuel filler doorhinge and doorcheck armMotorcraftSilicone

2Ensure the correct automatic transmission fluid is used. Transmissionfluid requirements are indicated on the dipstick or on the dipstickhandle. Check

VEHICLE DIMENSIONSRegular CabVehicledimensionsStyleside 6.5’box - inches(mm)Flareside 6.5’box - inches(mm)Styleside 8.0’box - inches(mm)(1) Overalllen

SuperCabVehicledimensionsStyleside 5.5’box - inches(mm)Styleside /Flareside 6.5’box - inches(mm)Styleside 8.0’box - inches(mm)(1) Overalllength217.8 (

Super CrewVehicle dimensions Styleside 5.5’ box -inches (mm)Styleside 6.5’ box -inches (mm)(1) Overall length 223.8 (5685) 235.8 (5990)(2) Overall wid

Super CrewVehicle dimensions Styleside 5.5’ box -inches (mm)Styleside 6.5’ box -inches (mm)(4) Wheelbase 138.5 (3518) 150.5 (3823 )(5) Track - Front 6

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for your vehiclethrough your local Ford or Ford of

LifestyleBedliners and bedmatsCargo organization and managementRear seat entertainment systemsTowing mirrorsTrailer hitches, wiring harnesses and acce

7. Text: This control currently notsupported.8. Shuffle: Press to play CD tracksin random order on the selected CD.9. Compress (Compression): InCD mod

AAccessory delay ...73Air cleaner filter ...312–313, 315Air conditioning ...49, 52Airbag supplementalrestr

Climate control(see Air conditioningor Heating) ...46, 49, 52Clock adjust6-CD in dash ...37AM/FM Stereo .

checking and adding ...282dipstick ...282filter, specifications ...285, 315recommendations ...

Infant seats(see Safety seats) ...151Inspection/maintenance (I/M)testing ...305Instrument panel

PParking brake ...207Parts (see Motorcraft parts) ...315Passenger OccupantClassification Sensor ...121Power di

four-wheel drivevehicles ...233–234utility-type vehicles ...8Specification chart,lubricants ...

336

17. ON/OFF/Volume: Press to turnON/OFF. Turn to increase/decreasevolume.If the volume is set above a certainlevel and the ignition is turned off,the v

Premium/Audiophile In-Dash Six CD/MP3/Satellite CompatibleSound System (if equipped)Premium/Audiophile In-Dash Six CD/MP3/Satellite CompatibleSound Sy

1. / Tune/Disc selector: Inradio mode, press to manually go up() or down ( ) the radiofrequency.In menu mode, use to select various settings.In CD mod

TREB (Treble): Press MENU until TREBLE appears in the display.Use/ / SEEK to adjust the treble levels.BASS: Press MENU until BASS appears in the displ

To activate, press and hold MENU until RDS (ON/OFF) appears in thedisplay. Use/ / SEEK to toggle RDS ON/OFF. When RDS ison, press MENU repeatedly to s

5. Seek: In radio mode, press/ to access the previous/nextstrong station.In CD mode, press/ toaccess the previous/next CD track.In Satellite Radio mod

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

11. Rewind: Press to manuallyreverse in a CD track.12. Memory presets: To set astation: Select frequency bandAM/FM1/FM2; tune to a station,press and h

Satellite radio is available only in the continental United States witha valid SIRIUS subscription.14. AM/FM: Press to selectAM/FM1/FM2 frequency band

• Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thunderstorms can interfere with your reception.• Station

label may peel and cause the CD to become jammed. It isrecommended that homemade CDs be identified with permanentfelt tip marker rather than adhesive

• Hardware and limited subscription term, which begins on the date ofsale or lease of the vehicle.• Online media player access: providing access to al

Radio Display Condition Action RequiredNO TEXT Artist information notavailable.Artist information notavailable at this time onthis channel. The system

HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe

3. Set the fan speed to the highest setting.4. Direct the outer instrument panel vents towards the side windows.To increase airflow to the outer instr

3.RRear defroster (if equipped): Press to defrost the rearwindow. Refer to Rear window defroster (if equipped) later in thischapter for more informati

Panel ( ) and panel/floor ( ) modes:• Move the temperature control to the coolest setting.• Select A/C and recirculated air (). Use recirculated air w

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

Temperature conversion: To switch between Fahrenheit and Celsius: Ifyour vehicle is equipped with a full message center, refer to Setup menuin the Mes

4. Recirculation control: Press to activate/deactivate airrecirculation in cabin. Recirculated air may reduce the amount of time tocool down the inter

Automatic Temperature Control (ATC) system with heated seats(if equipped)Temperature conversion: To switch between Fahrenheit and Celsius:If your vehi

MAX A/C: For maximum cooling performance, press , A/C, ,and set the temperature to 60°F and the highest blower setting.1.Defrost: Distributes outside

12. A/C control: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. Engagesautomat

Do not place objects on top of the instrument panel as theseobjects may become projectiles in a collision or sudden stop.REAR WINDOW DEFROSTER (IF EQU

HEADLAMP CONTROLRotate the headlamp controlclockwise to the first positiontoturn on the parking lamps. Rotateclockwise to the secondpositionto also tu

At this point, the headlamps and park lamps will turn off.Foglamp control (if equipped)The headlamp control also operatesthe foglamps. The foglamps ca

Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Lamp (DRL) systemdoes not activate the tail lamps an

3. Turn on the low beam headlamps to illuminate the wall or screen andopen the hood. Cover one of the headlamps so no light hits the wall.4. On the wa

SPECIAL NOTICESNew Vehicle Limited WarrantyFor a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited

INTERIOR LAMPSMap lampsTo turn on the map lamps, press thecontrol next to each lamp.Rear map lamp (if equipped)The rear map lamp lights arelocated on

Dome/courtesy lamps (if equipped)The dome lamp lights when:• any door is opened.• the instrument panel dimmerswitch is rotated up until thecourtesy la

Function Number ofbulbsTrade numberHeadlamps 2 H13 / 9008Front park/turn lamps 2 3157A (amber)Front sidemarker 2 194Foglamps 2 9140Backup lamp (except

5. Remove the bulb by turning itcounterclockwise, then pull itstraight out.Handle a halogen headlamp bulb carefully and keep out ofchildren’s reach. G

4. Slide the headlamp assemblyforward disconnecting the snapattachment at the fender.5. Remove bulb socket from thelamp assembly by turning itcounterc

Replacing high-mount brake and cargo lamp bulbsMake sure the headlamp control isin the OFF position.1. Remove the two screws and movethe lamp assembly

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

While holding the steering column,pull the lever up to its originalposition to lock the steering column.Never adjust the steeringcolumn when the vehic

OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehicle’s overhead console will vary according toyour option package. The overhead console can co

• When on the overhead rail, adjacent bins must be pinned together.Bins adjacent to the End Cap must be pinned to the End Cap. Binswithout pin attachm

Event Data RecordingOther modules in your vehicle — event data recorders — are capable ofcollecting and storing data during a crash or near crash even

While pushing upwards with palms, grip the side latches with fingers andsqueeze.With pressure applied with palms and side latches squeezed down, pulld

The auxiliary power point is locatedon the instrument panel.Do not use the power point foroperating the cigarette lighterelement (if equipped).To prev

When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not inthe proximity of the win

• Press and hold the bottom part ofthe rocker switch to open windowall the way to the full openposition.• Press and hold the top part of therocker swi

EXTERIOR MIRRORSPower side view mirrorsTo adjust your mirrors:1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterc

Heated outside mirrors (if equipped)Heated mirrors remove ice, mist andfog. To activate the heated mirrors,press the rear defrost buttonRlocated on th

Never adjust the accelerator and brake pedal with feet on thepedals while the vehicle is moving.SPEED CONTROL (IF EQUIPPED)With speed control set, you

Resuming a set speedPress the RES/RESUME control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RES/RESUMEco

• Depress the brake pedal until thedesired vehicle speed is reached,press the SET control.Turning off speed controlThere are two ways to turn off the

In Satellite Radio mode (if equipped):• Press and release SEEK to advance through preset channels or pressand hold SEEK to increment to the next subsc

Using your vehicle as an ambulanceDo not use this vehicle as an ambulance.Your vehicle is not equipped with the Ford Ambulance PreparationPackage.Noti

To open the moon roof: The moonroof is equipped with a one-touchopen feature. Press and releasethecontrol. The moon roofwill open to the “comfort” pos

When programming your HomeLink威 Wireless Control System toa garage door or gate, be sure that people and objects are out ofthe way to prevent potentia

3. Simultaneously press and holdboth the HomeLink威 and hand-heldtransmitter button. Do not releasethe buttons until Step 4 hasbeen completed.Some entr

Gate Operator & Canadian ProgrammingDuring programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time for

Erasing HomeLink姞 buttonsTo erase the three programmedbuttons (individual buttons cannotbe erased):• Press and hold the two outerHomeLink威 buttons unt

Usually, when something affects the compass readings, the compass willcorrect itself after a few days of operating your vehicle in normalconditions. I

1. Start the vehicle.2. To enter the compass calibrationmode, press and hold the button forgreater than eight seconds. Thedisplay will then show CAL i

Info menuThis control displays the followingcontrol displays:• Odometer/Compass• Trip odometer/Odometer/Compass• Distance to Empty• Average Fuel Econo

Compass zone/calibration adjustment1. Determine your magnetic zone byreferring to the zone map.2. Turn ignition to the ON position.3. Start the engine

10. The compass is now calibrated.Distance to empty (DTE)Selecting this function from theINFO menu estimates approximatelyhow far you can drive with t

Cell phone useThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri

2. Record the highway fuel economy for future reference.It is important to press the RESET control after setting the speedcontrol to get accurate high

The sequence of the system check report and how it appears in themessage center is as follows:1. FUEL LEVEL2. ENGINE TEMP3. OIL PRESSURE4. BRAKE FLUID

Language1. Select this function from theSETUP menu for the currentlanguage to be displayed.2. Pressing the RESET controlcycles the message center thro

Warning display StatusDoor ajar Warning can be resetLow fuel level Warning returns after 10 minutesCheck charging systemLow brake fluid levelLow oil p

LOW BRAKE FLUID LEVEL. Indicates the brake fluid level is low andthe brake system should be inspected immediately. Refer to Brake fluidreservoir in th

Position the floor mat so that theeyelet is over the pointed end of theretention post. Make sure that themat does not interfere with theoperation of t

To install, follow the removal procedures in reverse order.BED EXTENDER (IF EQUIPPED)Your vehicle may be equipped with a bed extender designed to exte

To remove the bed extender:1. Extend the bed extender.2. Pull the round knobs on each sideof the extender to unlock it.Make sure the locking clip scre

KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w

CHILDPROOF DOOR LOCKS (IF EQUIPPED)• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the ou