Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 15Entertainment Systems 18AM/FM stereo cassette with CD 18AM/FM stereo with in-
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
6. Pull off the bulb covers.7. Once the bulb covers areremoved, the bulbs can be removedby turning them counterclockwiseand then pulling the bulbs str
Replacing front parking lamp/turn/sidemarker signal bulbs1. Make sure that the headlamp control is in the OFF position.2. Open the hood.3. Remove the
4. Rotate the bulb socket counterclockwise and remove from lampassembly.5. Pull bulb straight out of socket and snap in the new bulb.6. Install the bu
Replacing foglamp bulbsHandle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and donot tou
Approach lamp/mirror turn signal bulb removal (if equipped)To change the bulbs:1. Make sure the headlamp switch isin the OFF position and then foldthe
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT STEERINGPush the lever down to unlock thesteering column. While the lever isin the down position, tilt thesteering column to the desiredposition.
Slide on rod feature (ifequipped)Rotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage.Note: To stow the viso
Power quarter rear windows (if equipped)• Without a moon roof• With a moon roofPress theportion of the VENT control to open the power rearquarter wind
CENTER CONSOLE (IF EQUIPPED)The center console offers several useful storage features. These include:1. Pen holder2. Tissue holder3. Large utility com
heavy acceleration and deceleration) and have your vehicle servicedimmediately by your authorized dealer.Under engine misfire conditions, excessive ex
The third auxiliary power point onthe center console is accessible fromthe rear seats.The rear auxiliary power point is located on the right rear quar
POWER WINDOWS (IF EQUIPPED)Do not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously inju
AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED)Your vehicle may be equipped withan inside rear view mirror with anauto-dimming function. Theel
Powerfold mirrors (if equipped)Rotate the 4–way adjustment switchto the center position. Press theswitch down to auto fold in anddown again to auto fo
Signal indicator mirrors (if equipped)When the turn signal is activated,the lower portion of the mirrorhousing will blink.POWER ADJUSTABLE FOOT PEDALS
Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas
Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RES contro
Reducing speed while using speed controlThere are two ways to reduce a setspeed:• Press and hold the COAST/CSTcontrol until you get to thedesired spee
STEERING WHEEL CONTROLS (IF EQUIPPED)These controls allow you to operate some radio and climate controlfeatures.Audio control featuresPressto select:•
Climate control featuresPress TMP + or - to adjusttemperature.Press+ or - to adjust fan speed.MOON ROOF (IF EQUIPPED)The moon roof control is located
Airbag readiness: If this light failsto illuminate when ignition is turnedto ON, continues to flash or remainson, have the system servicedimmediately
To open the moon roof: The moonroof is equipped with a one-touchopen feature. Press and releasethecontrol. The moon roofwill open to the “comfort” pos
Do not use the HomeLink威 Wireless Control System with any garagedoor opener that lacks safety stop and reverse features as required byU.S. federal saf
3. Simultaneously press and holdboth the HomeLink威 and hand-heldtransmitter button. Do not releasethe buttons until Step 4 hasbeen completed.Some entr
Gate Operator & Canadian ProgrammingDuring programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time for
Erasing HomeLink姞 buttonsTo erase the three programmedbuttons (individual buttons cannotbe erased):• Press and hold the two outerHomeLink威 buttons unt
Usually, when something affects the compass readings, the compass willcorrect itself after a few days of operating your vehicle in normalconditions. I
1. Start the vehicle.2. Locate the reset button on thecompass sensor mounted on thebase of mirror.3. To enter the compass calibrationmode, press and h
Info menuThis control displays the followingcontrol displays:• Odometer/Compass• Trip odometer/Odometer/Compass• Distance to Empty• Average Fuel Econo
Compass zone/calibration adjustment1. Determine your magnetic zone byreferring to the zone map.2. Turn ignition to the ON position.3. Start the engine
CALIBRATE display changes to CALIBRATION COMPLETE. It will takeup to five circles to complete calibration.11. The compass is now calibrated.Distance t
Check fuel cap (if equipped):Illuminates when the fuel cap maynot be properly installed. Continueddriving with this light on may causethe Service engi
1. Drive the vehicle at least 5 miles (8 km) with the speed controlsystem engaged to display a stabilized average.2. Record the highway fuel economy f
AutolocksThis feature automatically locks all vehicle doors when the vehicle isshifted into any gear, putting the vehicle in motion.1. To disable/enab
Language1. Select this function from theSETUP menu for the currentlanguage to be displayed.2. Pressing the RESET controlcycles the message center thro
4. OIL PRESSURE5. BRAKE FLUID LEVEL6. TIRE PRESSURE SYSTEM (if equipped)7. ADVANCETRAC威 with RSC (if equipped)8. AIR SUSPENSION SYSTEM (if equipped)9.
Warning display StatusPark assist ON/OFF (if equipped) Warning displays when R (reverse)gear is selected.Liftgate or liftglass ajar Warning returns af
CHECK PARK ASSIST (if equipped). Displayed when thetransmission is in R (Reverse) and the Reverse Sensing System isdisabled. Refer to Reverse Sensing
TIRE PRESSURE SENSOR FAULT (if equipped). Displayed when atire pressure sensor is malfunctioning, or your spare tire is in use. Formore information on
ADVTRAC OFF T/C ON with RSC (if equipped). Displayed on 4x4vehicles only when 4x4 Low Range is selected. In this mode, the stabilityenhancement portio
POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)Do not install additional floor mats on top of the factory installedfloor mats as they may interfere with th
Make sure the liftgate is closed to prevent exhaust fumes frombeing drawn into the vehicle. If you must drive with the liftgateopen, keep the vents op
Four wheel drive high (ifequipped): Illuminates whenfour-wheel drive is engaged. If thelight fails to illuminate when theignition is turned ON, or rem
KEYSOne key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency.Your keys are programmed to your v
CHILDPROOF DOOR LOCKSWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo
Unlocking the doors/liftgatePress this control to unlock thedriver’s door. The interior lamps willilluminate with the ignition is in the1 (OFF/LOCK) p
Sounding a panic alarmPress this control to activate thealarm.The personal panic alarm will cyclethe horn and parking lamps on/off.To deactivate the a
Deactivating the memory seat featureTo deactivate this feature:1. Press the SET control on the driver’s door panel.2. Within 5 five seconds, press any
Note: Replacement of the battery will not cause the remote transmitterto become deprogrammed from your vehicle. The remote transmittershould operate n
Illuminated entryThe lamps illuminate when the remote entry system is used to unlockthe door(s).The system automatically turns off after 25 seconds or
• release the liftgate glass,• enable or disable the autolock function, and• add or delete a 5–digit personal user code.Your vehicle has a factory set
Programming your own personal entry codeTo program your own code:1. Enter the factory set code (keypad will illuminate when pressed).2. Press the 1 •
3. Enter the 5–digit entry code4. Press and hold the 7 • 8. While holding the 7 • 8pressthe3• 4.5. Release the 3 • 4.6. Release the 7 • 8.The user sho
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the1 (OFF/LOCK) position.Automatic disarmingSwitching the ignition to
Replacing coded keys can be very costly and you may want to store anextra programmed key away from the vehicle in a safe place to preventan unforeseen
6. To program additional new unprogrammed key(s), repeat thisprocedure from Step 1.If successful, the new coded key(s) will start the vehicle’s engine
SEATINGFront row adjustable head restraints (if equipped)Your vehicle’s seats are equipped with two-way adjustable headrestraints. The purpose of thes
Lift handle to move seat forward orbackward.Seat reclinerAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips
Using the armrest (if equipped)Push the release control to movethe armrest up or down.Using the manual lumbar supportThe lumbar support control isloca
Adjusting the front power seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the sea
Memory seats/rearview mirrors/adjustable pedals (if equipped)This system allows automaticpositioning of the driver seat,outside rearview mirrors, anda
• There is a filter located underboth front seats.• It can be accessed from thesecond row seat. Move the frontseat all the way forward and upto ease a
To install climate controlled seat air filter:• First, position the filter in it’shousing making sure that the farforward end is all the way up inthe
Odometer: Registers the total miles (kilometers) of the vehicle.• With Mini Message Center• With Full Message CenterRefer to Message Center in theDriv
Adjusting the 2nd row outboard seat for E-Z EntryThe 2nd row outboard seats allow for easier entry and exit to and fromthe 3rd row seat.To enter the 3
3. To return the seat to a seatingposition, push down on the seatuntil the seat is latched to the floor.4. With the seat in the flat back position, li
1. Locate the handle on the side ofthe seat, lifting it to release theseatback.2. Ensure that the seat back islocked in the down position byapplying p
The rear latch hooks mustbe properly engaged withthe floor striker. Position the rearlegs of the seat over the floorstrikers and engage.2. With the se
To prevent possible damage to the seat or safety belts, ensurethat the safety belts are not buckled when moving the seat tothe load floor position.2.
Adjusting the second row 20% seat (if equipped)Lift the handle to move the seatforward or backward.Note: This seat can be moved forward to keep a chil
Third row adjustable head restraintsYour vehicle’s third row outboard seating positions are equipped withhead restraints which are vertically adjustab
Folding down the third row seat to the load floorTo prevent possible damage to the seat or safety belts, ensurethat the safety belts are not buckled w
Third row power folding seat (if equipped)The control buttons are located on the right-hand rear quarter trim panel(accessible from the liftgate area)
SAFETY RESTRAINTSPersonal Safety System姟The Personal Safety System娂 provides an improved overall level offrontal crash protection to front seat occupa
Battery voltage gauge: Indicatesthe battery voltage when theignition is in the ON position. If thepointer moves and stays outside thenormal operating
common, moderate-severity impacts. A higher energy level is used forthe most severe impacts. Refer to Airbag supplemental restraintssection in this ch
to the Warning lights and chimes section in the Instrument Clusterchapter. Routine maintenance of the Personal Safety System娂 is notrequired.The Restr
In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a safety belt.Each seating position in your vehicle h
• Front and rear seatsAll safety restraints in the vehicle are combination lap and shoulder beltswith the exception of a 60/40 front split bench seat
Shorten and fasten the belt whennot in use.All of the passenger combination lap and shoulder belts have two typesof locking modes described below:Vehi
How to use the automatic locking mode1. Buckle the combination lap andshoulder belt.2. Grasp the shoulder portion andpull downward until the entire be
BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe safety belt assembly “automatic locking retractor” feature orany other safety belt function is not
Front and second row safety belt height adjustmentYour vehicle has safety belt heightadjustments for the driver, rightfront passenger and second rowou
there are no nicks, tears or cuts. Replace if necessary. All safety beltassemblies, including retractors, buckles, front safety belt buckleassemblies,
If... Then...The driver’s safety belt is notbuckled approximately5 seconds after the safety beltwarning light has turned off...The BeltMinder威 feature
AUDIO SYSTEMSPremium Satellite Compatible AM/FM Stereo/Cassette/SingleCD/MP3 radio (if equipped)1. EJ (Eject): Press to stop andeject a tape.2. EJ (Ej
Reasons given... Consider...“I was in a hurry” Prime time for an accident.BeltMinder威 reminds us to take a fewseconds to buckle up.“Safety belts don’t
Deactivating/activating the BeltMinder姞 feature (if equipped)Read Steps1-4thoroughly before proceeding with thedeactivation/activation programming pro
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right
Never place your arm over the airbag module as a deployingairbag can result in serious arm fractures or other injuries.To properly position yourself a
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
impact sensors, the system wiring, the airbag system readiness light, theairbag back up power and the airbag ignitors).Determining if the system is op
All occupants of the vehicle including the driver should alwayswear their safety belts even when an airbag SRS and SafetyCanopy娂 system is provided.To
Children 12 years old and under should always be properly restrained inthe second or third row seats. The Safety Canopy娂 will not interferewith childr
Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref
4. BAL (Balance): Allows you toshift speaker sound between theright and left speakers. Press BALthen press TEXT/SEL to shift soundto the leftor right
Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.Alwa
Booster seats should be used until you can answer YES to ALL of thesequestions:• Can the child sit all the way backagainst the vehicle seat back withk
Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto
Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in acollision.SAFETY SEATS F
for children up to 60 pounds (27 kg) in a child restraint, and toprovide upper torso restraint for children up to 80 pounds (36 kg)using an upper tors
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a
Installing child safety seats in the center front seating position(if equipped)Always transport children 12 years old and under in the rearseats and a
The tether strap anchors in your vehicle are in the following positions(shown from top view):• Second row bench seat• Second row bucket seatsAttach th
• center seating position (ifequipped)3. Route the child safety seat tether strap under the head restraint(outboard seats) and over the back of the se
Seating and Safety Restraints 153Seating 153Safety restraints 169Airbags 182Child restraints 189Tires, Wheels and Loading 204Tire Information 206Tire
FF (Fast Forward): Works in tapeand CD modes.In the tape mode, tape directionautomatically reverses when the end of the tape is reached. Fast forwardi
6. Rotate the tether strap clip.7. Tighten the child safety seat tether strap according to themanufacturer’s instructions.Third row seating position1.
4. Clip the tether strap through theanchor loop as shown.If the tether strap is clippedincorrectly, the child safetyseat may not be retained properlyi
Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol:Never attach two LATCH child safe
Attach LATCH lower attachments of the child seat only to theanchors shown.If you install a child seat with rigid LATCH attachments, do not tightenthe
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary.
• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and
government test course. For example, a tire graded 150 would wear oneand one-half (1 1/2) times as well on the government course as a tiregraded 100.
• Tire Identification Number (TIN): A number on the sidewall ofeach tire providing information about the tire brand andmanufacturing plant, tire size
Every day before you drive, check yourtires. If one looks lower than the others,use a tire gauge to check pressure of alltires and adjust if required.
• Folder/Track mode: In MP3 mode, press MENU until MODE appearsin the display. Use SEL to toggle between FOLDER (only tracks withinthe selected folder
the B-Pillar or the edge of the driver’s door. The cold inflation pressureshould never be set lower than the recommended pressure on the SafetyComplia
TIRE CAREInspecting your tiresPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones, nails or glass that
AgeTires degrade over time, even when they are not being used. It isrecommended that tires generally be replaced after 6 years of normalservice. Heat
It is recommended that the two front tires or two rear tires generally bereplaced as a pair.The tire pressure monitoring sensors mounted in the wheels
speed. Drive with caution until you can safely pull off the road. Stop andinspect the tires for damage. If a tire is under-inflated or damaged,deflate
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
17. TAPE: Press to begin tape play.Press to switch tape side (1 to 2) or(2 to 1).18. CD slot: Insert the disc with the playing side down and printed s
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe
Changing tires with TPMSIt is recommended that you alwayshave your tires serviced by anauthorized dealer. Each road tireis equipped with a tire pressu
When your temporary spare tire is installedWhen one of your road tires needs to be replaced with the temporaryspare, the TPMS system will continue to
Low Tire PressureWarning LightCustomer Action RequiredSolid Warning Light 1. Check your tire pressure to ensure they areproperly inflated, refer to In
When inflating your tiresWhen putting air into your tires (such as at a gas station or in yourgarage), the Tire Pressure Monitoring System may not res
activate the TPMS warning for low tire pressure. If the low warning lightis on, visually check each tire to verify that no tire is flat. If one or mor
VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
Audiophile/Premium Satellite Compatible AM/FM Stereo In-DashSix CD/MP3 Radio (if equipped)1. SEEK: Press and releaseSEEK/ for previous/nextstrong stat
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).
10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), and driver only (150 lb. [68 kg]). Consult your authorizeddealer (or
6. If your vehicle will be towing a trailer, load from your trailer will betransferred to your vehicle. Consult this manual to determine how thisreduc
Special loading instructions for owners of pickup trucks andutility-type vehiclesFor important information regarding safe operation of this typeof veh
Trailer towing (standard equipment):Your vehicle is equipped with a integrated trailer hitch and a Class I(4-pin) trailer electrical connector. The 4-
EngineRear axleratioMaximum GCWR -lb. (kg)Trailer weight range(0 - maximum)lb. (kg)4x45.4L withstandardtrailer towpackageAll 11900 (5397) 0–6000 (0–27
Mode MaximumGross TrailerWeight-kg(lb.)MaximumTongue Weight-kg(lb.)Weight carrying 2721 (6000) 272 (600)Weight distributing 4060 (8950) 406 (895)These
5. Turn the air suspension (if equipped) control to ON.Note: Adjusting an equalizing hitch so the rear bumper of the vehicle ishigher than it was unlo
• To eliminate excessive shifting, use a lower gear. This will also assistin transmission cooling. (For additional information, refer toUnderstanding
3. AUX: Press to toggle between thecurrent playing media and DVD (ifequipped).4. MUTE: Press to MUTE playingmedia; press again to return toplaying med
• Vehicles with trailers should not be parked on a grade. If you mustpark on a grade, place wheel chocks under the trailer’s wheels.Launching or retri
Vehicles equipped with Control Trac four-wheel drive system:Vehicles equipped with the Control Trac four-wheel drive system cannotbe towed with any wh
STARTINGPositions of the ignition1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval.2. ACCESSORY, allow
If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf
5. Turn the key to 3 (ON) withoutturning the key to 4 (START).Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrum
Guarding against exhaust fumesCarbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects.If you smell exhaust fumes i
BRAKESYour service brakes are self-adjusting. Refer to the scheduledmaintenance information for scheduled maintenance.Occasional brake noise is normal
Using ABS• In an emergency or when maximum efficiency from the four-wheelABS is required, apply continuous force on the brake. The four wheelABS will
Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th
ADVANCETRAC姞 WITH ROLL STABILITY CONTROL姟 (RSC)STABILITY ENHANCEMENT SYSTEM (IF EQUIPPED)AdvanceTrac威 with RSC is an integrated system with four major
Traffic (if equipped): Allows you to hear traffic broadcasts. With thefeature ON, press SEEK or SCAN to find a station broadcasting a trafficreport (i
• Maneuvering quickly to avoid an accident, pedestrian or obstacle• Hitting a patch of ice• Changing lanes on a snow-rutted road• Entering a snow-free
RSC stability enhancement and traction enhancement feature. If thevehicle is stuck in snow or mud or when driving in deep sand, switchingoff the Advan
STEERINGYour vehicle is equipped with power steering. Power steering uses energyfrom the engine to decrease the driver’s effort in steering the vehicl
If a load is added to, or removed from the vehicle, the load levelingfeature of the air suspension system will adjust the suspension to keepthe vehicl
LIMITED-SLIP AXLE (IF EQUIPPED)This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under
Use extra caution while becoming familiar with your vehicle. Know thecapabilities and limitations of both you as a driver and your vehicle.AUTOMATIC T
Do not drive your vehicle until you verify that the brakelampsare working.Always set the parking brake fully and make sure the gearshift islatched in
Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position andremove the key wheneve
To return to D (Drive) with Overdrive mode, press the transmissioncontrol switch (TCS). The TCIL will no longer be illuminated.Each time the vehicle i
REVERSE SENSING SYSTEM (IF EQUIPPED)The RSS sounds a tone to warn the driver of obstacles near the rearbumper when R (Reverse) is selected. The RSS wi
10. REPEAT: Press to repeat thecurrent CD/MP3 track.11. SHUFFLE: Press play theCD/MP3 tracks on the current discin random order.12. FOLDER: Press to a
The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to th
If equipped with the Control Trac 4x4 System, and 4L (4x4 LOW)is selected while the vehicle is moving, the system will notengage. This is normal and s
• 4H (4X4 HIGH) provides mechanically locked four-wheel drive powerto front and rear wheels. The “4X4 HIGH” light will illuminate in theinstrument clu
Shifting from 2H to A4WD or 4HMove the control to the A4WD or4H position at any forward speed upto 55 mph (88 km/h). The “4X4”light in the instrument
Shifting from 4L to 4H, A4WD or 2H1. Bring the vehicle to a stop andkeep the brake pedal depressed.2. Place the gearshift in N (Neutral).3. Move the c
steering and braking control of your vehicle, you must have all fourwheels on the ground and they must be rolling, not sliding or spinning.Basic opera
Do not rock the vehicle if the engine is not at normal operatingtemperature or damage to the transmission may occur.Do not rock the vehicle for more t
• If the vehicle goes from one type of surface to another (i.e., fromconcrete to gravel) there will be a change in the way the vehicleresponds to a ma
If your vehicle is equipped with AdvanceTrac威 with RSC, press theAdvanceTrac威 with RSC button (refer to AdvanceTrac威 with RollStability Control (RSC)
Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should
20. Load: Press to load a CD. Pressand hold to load up to six discs.21. CD: Press to enter CD mode.CD units are designed to play commercially pressed
Driving on snow and iceFour–wheel drive vehicles have advantages over two–wheel drivevehicles in snow and ice but can skid like any other vehicle.Shou
DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
Canadian customers refer to your Owner Information Guide forinformation on:• coverage period• exact fuel amounts• towing of your disabled vehicle• eme
HAZARD FLASHERUse only in an emergency to warn traffic of vehicle breakdown,approaching danger, etc. The hazard flashers can be operated when theignit
The fuel pump shut-off switch has ared reset button on top of it and islocated beneath the air suspensionswitch (if equipped).Use the following proced
FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth
Passenger compartment fuse panel / power distribution boxThe fuse panel is located under the right-hand side of the instrumentpanel.To remove the trim
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 7.5A* Run/Accessory - Front wipermotor, In
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description5 7.5A* Powertrain Control Module (PCM)(KA power), Speed controldeactivatio
Rear seat radio controls (if equipped)If your vehicle is equipped with afront row console, then it is alsoequipped with rear seat radiocontrols.If you
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description12 15A* Fuel pump relay, Fuel pumpshut-off switch, Fuel pump drivermodule,
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description20 30A* BSM (door locks, liftgate glassrelease relay), Liftgate glassreleas
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description29 30A* Trailer tow electric brakecontroller, Trailer tow 7–wireconnector (
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description41 20A* Cigarette lighter, OBD IIdiagnostic connector42 10A* Trailer tow le
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description115 30A** Transfer case shift motor, 4x4relays116 40A** Front blower motor
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionR203 PCM relay Fuse 32, Fuse 34, PCM solenoidsand sensorsR301 Trailer towba
If your vehicle is equipped with a Tire Pressure MonitoringSystem, refer to Tire Pressure Monitoring System (TPMS) inthe Tires, Wheels and Loading cha
Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following:• Handling, stability and braki
Spare tire informationNote: If your vehicle is equipped with the tire pressure monitoringsystem (TPMS), the system indicator light will illuminate whe
Removing the spare tire1. Fold the rear seat down. Refer toRear seats in the Seating andsafety restraints chapter.2. Remove the jack handle andwinch e
To activate Dual Play mode (rearseat passengers listen to a differentplaying media than the front seatpassengers):• Press the speaker/headphonecontrol
1. Park on a level surface, activatehazard flashers and set the parkingbrake.2. Place gearshift lever in P (Park),turn engine OFF and block thediagona
6. Lift the vehicle so the tire is no further than 1 inch (2.5 cm) off theground when installing the spare tire.When one of the rear wheels is off the
7. Remove the lug nuts with the lug wrench.8. Replace the flat tire with the spare tire, making sure the valve stem isfacing outward. Reinstall the lu
5. Disassemble the tools and snap them back into the tool tray. Close theaccess hole with the rubber plug. Reinstall the tray into the vehicle andsecu
Preparing your vehicleWhen the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, th
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
4. Make the final connection of the negative (-) cable to the jumpstarting stud located in the rear of the engine compartment, near thebattery. Do not
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
Maintenance and Specifications 316Engine compartment 318Engine oil 321Battery 324Engine Coolant 326Fuel information 332Air filter(s) 346Part numbers 3
Turning the rear speakers on and offPress the headphone/speakercontrol to turn the rear speakers on(Single Play mode) or off (Dual Playmode).Using hea
If the vehicle is towed by other means or incorrectly, vehicledamage may occur.With a disabled vehicle (without access to wheel dollies, car haulingtr
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh
authorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of Canada participates in an impartialthird party
GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.
Or call:For a free publication catalog, order toll free: 1-800-782-4356Monday-Friday 8:00 a.m. - 6:00 p.m. ESTHelm, Incorporated can also be reached b
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
WAXINGApplying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage.• Wash the ve
Memory preset controlPush the MEMORY/MEM controlsuccessively to allow rear seatpassengers to scroll through the6 memory presets in AM, FM1 orFM2.Push
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub
INTERIORFor fabric, carpets, cloth seats and safety belts:• Remove dust and loose dirt with a vacuum cleaner.• Remove light stains and soil with Motor
LEATHER SEATS FOR THE KING RANCH EXPEDITION ONLY(IF EQUIPPED)Your vehicle is equipped with seating covered in premium, top-grainleather which is extre
ConditioningBottles of King Ranch Leather Conditioner are available at the KingRanch Saddle Shop. Visit the Web site at www.krsaddleshop.com,ortelepho
Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A)Motorcraft Detail Wash (ZC-3–A)Motorcraft Dusting Cloth (ZC-24)Motorcraft Engine Sham
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide sc
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel.2. Go to the front of the vehicle a
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT5.4L 3V– V8 engines1. Battery2. Automatic transmission fluid dipstick3. Air filter assembly4. Engine o
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
GENERAL AUDIO INFORMATIONRadio frequencies: AM and FM frequencies are established by theFederal Communications Commission (FCC) and the Canadian Radio
CHANGING THE WIPER BLADESIt is recommended that wiper blades are renewed before winter.To replace the wiper blades:1. Fold back the wiper arm andposit
ENGINE OILChecking the engine oilRefer to the scheduled maintenance information for the appropriateintervals for checking the engine oil.1. Make sure
• If required, add engine oil to theengine. Refer to Adding engineoil in this chapter.• Do not overfill the enginewith oil. Oil levels above thismark
Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oil.Only use oils “Certified For Gasoline Engines” by t
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How
Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lightedsubstances to come near th
battery. When the battery is disconnected or a new battery is installed,the engine must relearn its idle and fuel trim strategy for optimumdriveabilit
FILL RANGE” in the coolant reservoir. If the level falls below, addcoolant per the instructions in the Adding engine coolant section.Your vehicle was
Note: Automotive fluids are not interchangeable; do not use enginecoolant, antifreeze or windshield washer fluid outside of its specifiedfunction and
• Do not add extra inhibitors or additives to the coolant. Thesecan be harmful and compromise the corrosion protection of the enginecoolant.For vehicl
• Expose discs to direct sunlight or heat sources for extended periodsof time.• Clean using a circular motion.CD units are designed to play commercial
Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage.Recycle
• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damag
When fail-safe mode is activatedYou have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be ab
If you do not use the proper fuel filler cap, excessive pressure orvacuum in the fuel tank may damage the fuel system or causethe fuel cap to disengag
splashed on the skin, promptly wash skin thoroughly with soap andwater. Consult a physician immediately if you experience an adversereaction.When refu
Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1/4 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref
If you do not use the proper fuel filler cap, excessive pressure orvacuum in the fuel tank may damage the fuel system or causethe fuel cap to disengag
Do not be concerned if your engine sometimes knocks lightly. However, ifit knocks heavily under most driving conditions while you are using fuelwith t
possible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel economy. We do not recommendtaking fuel econ
3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading.4. Subtract your initial odometer reading fro
DVD player controls1. MAIN control• NEXT — Press to access the next track on the CD, the next chapteron the DVD, or to go up in cursor mode.• PREV — P
• Resting your foot on the brake pedal while driving may reduce fueleconomy.• Combine errands and minimize stop-and-go driving.Maintenance• Keep tires
It is important to note the box in the lower left corner of the windowsticker. These numbers represent the range of fuel economy expected onthe vehicl
sells, leases, trades vehicles, or supervises a fleet of vehicles are notpermitted to intentionally remove an emission control device or preventit fro
condition. To ready the on-board diagnostics system for I/M testing, aminimum of 30 minutes of city and highway driving is necessary asdescribed below
BRAKE FLUIDThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“
7. Remove the dipstick and inspect the fluid level. The fluid should be inthe designated area for normal operating temperature or ambienttemperature.L
If necessary, add fluid in 1/2 pint (250 mL) increments through the fillertube until the level is correct.If an overfill occurs, excess fluidshould be
2. Pull air filter tray assembly outtoward front of vehicle and lift airfilter element up and out of housing.The air filter box needs to be free of an
MOTORCRAFT PART NUMBERSComponent 5.4L 3V V8 engineAir filter element FA-1754Battery BXT-65-650Fuel filter FG-986BOil filter FL-820-SPCV valve1Spark pl
REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to line onreservoi
7. Auxiliary jacksInput jacks for standard video/audio media device.8. STOP/EJECT controlPress once to stop DVD play. Press again to eject the DVD.9.
Fluid Ford PartNameApplication CapacityEngine coolant3MotorcraftPremium GoldEngine Coolant(yellow-colored)5.4L BaseRadiator withoutaux rear heat19.4 q
Some transmission fluids may be labeled as dual usage, such asMERCON威 and MERCON威 V. These dual usage fluids are not to be usedin an automatic transmi
LUBRICANT SPECIFICATIONSItemFord partnameFord partnumberFordspecificationBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluidPM-1 or PM
ItemFord partnameFord partnumberFordspecificationEngine oil Motorcraft SAE5W-20 PremiumSynthetic BlendMotor OilMotorcraft SAE5W-20 SuperPremium MotorO
ItemFord partnameFord partnumberFordspecificationWindshieldwasher fluidMotorcraftPremiumWindshieldWasherConcentrateZC-32–A WSB-M8B16–A21Ensure the cor
VEHICLE DIMENSIONSVehicle dimensions 4x2 – inches (mm) 4x4 – inches (mm)(1) Overall length 205.8 (5228) 205.8 (5228)(2) Vehicle width(Body)78.7 (2000)
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel.Please
TRANSMISSION/TRANSAXLE CODE DESIGNATIONSYou can find atransmission/transaxle code on theSafety Compliance CertificationLabel. The following table tell
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
• Press the FWD control to movethe cursor right one positionNext/Previous controlThe NEXT (up) and PREV (down)controls allow you to access thenext or
LifestyleCargo organization and managementSmoker’s packageRear seat entertainment systemsTrailer hitches, wiring harnesses and accessoriesPeace of min
AABS (see Brakes) ...246Accessory delay ...111Air cleaner filter ...346, 348Air conditioning ...
waxing ...309wheels ...309wiper blades ...311Climate con
recommendations ...323refill capacities ...349specifications ...352, 354Exhaust fumes ...
positioning ...285storage ...285Jump-starting your vehicle ...293KKeyless entry syste
Power distribution box(see Fuses) ...277Power door locks ...140Power mirrors ...
TTire Pressure MonitoringSystem (TPMS)Driving ...267Roadside Emergencies ...285Tires, Wheels and Loading ...
367
368
FWD or REV control for slow motion playback. Three different speedsare available depending on how long the control is held. Press thecontrol once for
Remote control1. REWIND controlPress to reverse the direction of the DVD movie.2. FAST FORWARD controlPress to advance the direction of the DVD movie.
7. MNU/MODE controlIn DVD playback mode, press to access the disc menu.In stop mode, press to change to a different playing media (e.g. AM, FM,CD...)8
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
Wireless headphonesYour system is equipped with 2 setsof wireless headphones. (Two AAAbatteries are needed to operate theheadphones.) Batteries are in
When not using the headphones,shut them off to preserve batterypower. The headphones willautomatically turn off after fiveminutes if they have not rec
Playback and format• The DVD player of your Rear Seat Entertainment DVD System canonly be used in the “playback” mode. (The DVD player does not offera
• To disable the DVD player, simultaneously press the 3 and 5 memorypresets on the radio face. To enable the DVD player again, press the 3and 5 preset
Playing an auxiliary device1. Connect the video line from your video device to the YELLOWauxiliary input jack.2. Connect the left and right audio line
9. DISPLAY SETTING (4x3, Zoom, 16x9)10. STATUS ICON (FWD, x4, x8, x32, REV, x4, x8, x32, etc.)Safety informationRead all of the safety and operating i
Federal Communication Commission (FCC) ComplianceChanges or modifications not approved by Ford Motor Company couldvoid user’s authority to operate the
Cleaning the liquid crystal display (LCD) flip-down screenClean the display screen by applying a small amount of water or anyammonia-based household g
Ford Motor Company shall not be liable for any damages of anytype arising from failure to follow these guidelines.Do not attempt to service, repair or
• To use the system as effectively and safely as possible, obtainup-to-date navigation CD’s whenever they become available.• Set the volume level so t
Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti
3. Navigation (NAV): Press theNAV control to access the navigationsystem menu.4. Cursor control: Use this controlwhen viewing a menu in thenavigation
10. AM/FM: Press to listen to theAM or FM frequency band (AM,FM1, FM2). Pressing AM/FM inNavigation mode will return you tothe audio screen.11. On/vol
Quick start – how to get goingTo play a radio station:1. Ensure that the ignition and the Vehicle Navigation Radio (VNR)system are ON.2. Press the AM/
Note: To use the navigation system and listen to an audio CD, thenavigation CD must be loaded into the VNR and the audio CD must beloaded into the CD
To adjust the navigation voice output level, adjust the volume controlonly when the navigation system is speaking. Otherwise, it will adjust theradio
AM/FM select in radio modeThis control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset
Adjusting the levels1. Press the MENU control.2. Select the AUDIO OPTIONS softkey.3. Select BASS, TREB, BAL orFADE.The bass adjust allows you toincrea
You can then select from thefollowing signal modes:• NEWS — ”voice-only” type ofsound with a limited audio band• JAZZ CLUB — jazz club withclearly ref
Seek in CD or CD DJ mode• Pressto seek to the previous track of the current disc. If aselection has been playing for three seconds or more and youpres
Starting autoset memory preset1. Select a frequency band using the AM/FM select controls.2. Press the AUTO control.3. When the first six strong statio
Please read the section Supplemental restraint system (SRS)in the Seating and Safety Restraints chapter. Failure to followthe specific warnings and in
Scan functionPress the soft key next to SCAN fora brief sampling of all listenablestations on the selected frequency.Press again to disable scan andre
CompressionThe compression feature will boostquieter music and lower loudermusic to minimize the need forvolume adjustments.When in CD or CD DJ mode,
CD DJYour vehicle is equipped with a CD DJ (CD changer). It is located in thecenter console.Radio power must be turned on to play the CDs in the CD DJ
Press to eject the magazine.1. Pull the lever to remove a CDtray from the magazine.2. Insert one disc into each CD trayof the magazine (up to 6 discs)
4. Insert the CD magazine into theCD DJ.5. Slide the door to the left to close.Use only compact discs containingthis mark.The magazine does not need t
CD DJ information screenThe CD DJ screen will displayvarious information such as:• Track selected• Elapsed time• Selected disc• Volume level• On-scree
Scan featureWhen in CD DJ mode, press SCANfor a brief sampling of all tracks onthe current CD. Press again todisengage the feature and listen tothe se
When RSC is active, pressing presets 2 and 4 simultaneously on the radiowill enable Dual Play mode (or the RSC can enable Dual Play mode bypressing th
Navigation screen displayWhen in navigation mode, there willbe various indicators on the screen tohelp you in operating your system.1. Direction to de
The GPS signal strength may vary. The directional heading indicator atthe bottom of the screen might change color to indicate this signalstrength. The
Notice to owners of pickup trucks and utility type vehiclesUtility vehicles have a significantly higher rollover rate thanother types of vehicles.Befo
From this menu, you may selectfrom the following options:• Address/Intersection – Use toselect a destination based on aknown street address orintersec
• By Category – Lists POIs bycategories, such as airports, gasstations, etc. Use the cursorcontrol to select and confirmchoice.• By Name – A keyboard
Deleting a previous destination• Use the cursor control to selectthe destination to be deleted.• Press DELETE.A confirmation screen will appearbefore
1. Shortest time route — Creates a driving route which minimizesdriving time taking into consideration things such as speed limits,number of turns, et
You are able to choose from three viewing options in this display:• PLAN — Press this soft key to scroll through your entire route. Thisoption is only
True viewAs you approach an intersection, theGuide display screen willautomatically change to a close-upview (True view) of the junction.The close-up
Adding, deleting or editing the address bookNote: These features are not available when the vehicle is in motion.1. Ensure that you are in navigationm
Current locationTo access your current location,press this control when innavigation mode. Your currentlocation and the name/distance tothe next/last
Route interruptionsIn the course of your destination, you may decide to temporarily leaveyour planned route for gas, food, etc. If you turn off the ig
Navigation optionsOnce in the navigation preferencemenu, you may select from thefollowing options:• VOICE — Select to turn the voiceoutput on or off a
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
1. Access the CLOCK screen.2. Press the TIME control to selectthe hours or minutes to set.3. Use the cursor control to increaseor decrease the hours o
Do not clean any part of the system with benzene, paint thinner or anyother solvent.Do not spill liquids of any kind onto the unit.The navigation syst
Latest map CDsThe traffic network is constantly changing due to new roads, trafficrestrictions, etc. Therefore, it is not always possible to exactly m
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM(IF EQUIPPED)1. A/C: Uses outside air to cool thevehicle. Press to turn on/off in allmodes exceptor .2
5. DUAL (Single/dual electrictemperature control): Allows thedriver to have full control of thecabin temperature settings (single zone) or allows the
16. Temperature conversion:Press to toggle between Fahrenheitand Celsius temperature on theDATC display only. The set point temperatures in Celsius wi
Will work in all modes except defrost. In automatic operation, therecirculated air operates automatically as necessary to achieve theselected temperat
9. OFF: Outside air is shut out andthe fan will not operate.10. Manual override controls: Allows you to manually select whereairflow is directed. To r
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
16. EXT control: Press to displaythe outside air temperature. Pressagain to return to interiortemperature. Note: Exteriorreadings are most accurate wh
AUXILIARY A/C-HEATER CONTROLS (IF EQUIPPED)Your vehicle may be equipped with auxiliary climate controls. Theseallow the front or rear seat passengers
Rear auxiliary controls (if equipped):Once the front auxiliary control is set to REAR, the rear seat passengersmay use the rear auxiliary controls in
HEADLAMP CONTROLRotate the headlamp control to thefirst positionto turn on theparking lamps. Rotate to the secondpositionto turn on theheadlamps.Autol
High beamsPush the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate.Flash to passPull toward you slightly to acti
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parklamp operatio
5. Locate the vertical adjuster oneach headlamp, then use a 10 mmsocket/wrench to turn the adjustereither counterclockwise (to adjustdown) or clockwis
Front row map/dome lamp (if equipped)The dome lamp lights when:• any door is opened,• the instrument panel dimmerswitch is rotated up until thecourtes
BULB REPLACEMENTHeadlamp CondensationThe headlamps are vented to equalize pressure. When moist air entersthe headlamp(s) through the vents, there is a
Function Number ofbulbsTrade number* To obtain replacement approach lamp assembly bulbs, see yourauthorized dealer and reference Ford part no. 2L1Z–13
Commentaires sur ces manuels