Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 14Entertainment Systems 17AM/FM stereo with CD 17AM/FM stereo with in-dash six
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A wa
• you shift into any gear putting the vehicle in motion, and• the brake pedal is released and the vehicle attains a speed greaterthan 5 mph (8 km/h).T
3. Enter factory-set 5–digit entry code.4. Press and hold the 7 • 8. While holding the 7 • 8 press the 3 • 4.5. Release the 3 • 4.6. Release the 7 • 8
If a problem occurs with the SecuriLock娂 system, the indicator will flashrapidly or glow steadily when the ignition is in the 3 (RUN) position. Ifthis
Programming spare keysYou can program your own coded keys to your vehicle.Tips:• A maximum of eight keys can be coded to your vehicle.• Only use Secur
9. Remove the newly programmed coded key from the ignition.If the key has been successfully programmed it will start the vehicle’sengine and the theft
• Press the driver or passengerinterior door lock control whilethe door is open, then close thedoor.• Press the 7 • 8 and 9 • 0controls on the keyless
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Always drive and ride with your seatback upright and the lapbelt snug and low across the hips.Lift handle to move seat forward orbackward.Pull lever u
Folding down the front passenger seatback (if equipped)The front passenger seatback can befolded to a horizontal position tomake room for a long load.
Press the front or rear portion to tiltthe seat.• DriverPress the control to move the seatforward, backward, up or down.• DriverPress the control to m
Check fuel cap: Illuminates whenthe fuel cap may not be properlyinstalled. Continued driving withthis light on may cause the Checkengine warning light
The indicator light on the control will illuminate when activated. For lowheat, 1 light will be lit; for high heat, both lights will be lit.The heatin
The head restraints can be movedup by pulling up on the headrestraint.Push release button to lower headrestraint.Adjusting second row bucket and bench
Adjusting second row seats (if equipped)Lift the control to adjust the seatforward or backward.Accessing the third row seatsEnsure head restraint is i
Lift the handle all the way up untilthe seat releases from the floor.Rotate the seat forward to allowaccess to the third row.To return the seatback to
Exiting the third row seatPull on the strap located on theback of the second row seat. Thiswill fold the seatback forward. Pullthe strap a second time
Ensure that the rear latch hooks areproperly engaged with the floorstriker.Note: Ensure that the seat andseatback are latched securely inposition. Kee
2. From the rear of the vehicle, fold seatback by pulling and holding thenumber 1 strap while pushing the seatback forward. Release strap onceseatback
1. Lift the seat out of the tub in the floor by squeezing and pulling up onthe handle. Once the seat is at a vertical position, push the seat over,let
The tailgate position is not a position suitable for driving. Do notdrive the vehicle with the seat in the tailgate position. The safetybelts are not
the system. Rather, it means the Personal Safety System determined theaccident conditions (crash severity, belt usage, etc.) were notappropriate to ac
Safety belt: Reminds you to fastenyour safety belt. A chime will alsosound to remind you to fasten yoursafety belt.Charging system: Illuminates whenth
Air bags can kill or injure a child in a child seat. NEVER place arear-facing child seat in front of an active air bag. If you mustuse a forward-facin
Determining if the Personal Safety System is operationalThe Personal Safety System uses a warning light in the instrumentcluster or a back-up tone to
It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in these areasare more likely to be se
2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.All restraints in the vehicle are combination lap and shoulder belts.While
This mode should be used any time a child safety seat is installed in apassenger front or outboard rear seating position (if equipped). Children12 yea
Unbuckle the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic locking mode and activate thevehicle sensitive
If... Then...The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition...The safety belt warning light andindicator chi
If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2minutes h
Reasons given... Consider...“Belts are uncomfortable” We design our safety belts to enhancecomfort. If you are uncomfortable -try different positions
Do not sit on top of a buckled safety belt to avoid the BeltMinder chime. Sitting on the safety belt will increase the risk ofinjury in an accident. T
Speed control: Illuminates whenthe speed control is engaged. Turnsoff when the speed control systemis disengaged.Low washer fluid: Illuminateswhen the
• Step 3 must be completed within 50 seconds after the safety beltwarning light turns off.3. For the seating position being disabled, buckle then unbu
hardware, should be inspected after a collision. Ford Motor Companyrecommends that all safety belt assemblies in use in vehicles involved ina collisio
Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in
• Recline the seat slightly one or two degrees from the upright position.Do not put anything on or over the air bag module. Placingobjects on or over
A difficulty with the system is indicated by one or more of the following:• The readiness light (same lightfor front and side air bag system)will eith
The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burn
• diagnostic module.• and the electrical wiring which connects the components.The diagnostic module monitors its own internal circuits and thesuppleme
When the front passenger seat isoccupied and the sensing systemhas turned off the passenger’sfrontal air bag, the ⬙passenger airbagoff⬙ or ⬙pass airba
Sitting improperly out of position or with the seat back reclinedtoo far can take off weight from the seat cushion and affect thedecision of the passe
Side air bag system (if equipped)Do not place objects or mount equipment on or near the air bagcover on the side of the seatbacks of the front seats o
Parking brake ON: Sounds when the parking brake is left ON anddriven. If the warning stays on after the park brake is off, contact yourdealer as soon
The side air bag system consists ofthe following:• An inflatable nylon bag (air bag)with a gas generator concealedbehind the outboard bolster ofthe dr
If the side air bag hasdeployed, the air bag willnot function again. The sideair bag system (including theseat) must be inspected andserviced by a qua
All occupants of the vehicle including the driver should alwayswear their safety belts even when an air bag SRS and SafetyCanopy娂 system is provided.T
The Safety Canopy娂 system, in combination with seat belts, can helpreduce the risk of severe injuries in the event of a significant side impactcollisi
If the Safety Canopy娂 system has deployed, the SafetyCanopy娂 will not function again unless replaced. TheSafety Canopy娂 system (including the A, B, C,
or younger and who weigh 40 lbs[18 kg] or less) ride in your vehicle, youmust put them in safety seats made especially for children. Many statesrequir
Booster seats position a child so that safety belts fit better. They lift thechild up so that the lap belt rests low across the hips and the kneesbend
• Those with a high back.If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo
SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully fo
Carefully follow all of the manufacturer’s instructions includedwith the safety seat you put in your vehicle. If you do not installand use the safety
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a
Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a
Front passenger seating position (delivery van only)1. Position the child safety seat onthe passenger seat cushion.2. Route the child safety seat teth
4. Rotate the tether hook, and clipthe tether strap to the seat frame.If the tether strap is clippedincorrectly (as shown) thechild safety seat may no
7. Tighten the child safety seattether strap according to themanufacturer’s instructions.Rear seating positionsFollow steps 1–7 as described above for
• 3rd row benchFor additional important safety information on the proper use of safetybelts, child seats and infant seats, please read the entire Seat
The lower anchors for child seatinstallation are located at the rearsection of the rear seat between thecushion and seat back.Follow the child seat ma
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
• With Message CenterTo reset, select the TRIP functionfrom the INFO menu. Depressingthe RESET control forapproximately one second will resetthe trip
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
Inspecting your tiresPeriodically inspect the tire treads for uneven or excessive wear andremove stones, nails, glass or other objects that may be wed
higher than the manufacturer’s recommended cold inflation pressurewhich can be found on either the tire label or certification label which islocated o
TIRE REPLACEMENT REQUIREMENTSYour vehicle is equipped with tires designed to provide a safe ride andhandling capability.Only use replacement tires and
If you use the temporary spare tire continuously or do not followthese precautions, the tire could fail, causing you to lose controlof the vehicle, po
the road tires and wheels that were originally provided by Ford. If thedissimilar spare tire or wheel is damaged, it should be replaced ratherthan rep
1. Remove the carpeted floor panellocated in the rear of the vehicle,remove the wing nut that securesthe spare tire by turning itcounterclockwise.2. L
To help prevent the vehicle from moving when you change a tire,be sure to place the transaxle in P (Park), set the parking brakeand block (in both dir
4. Put the jack in the jack notchnext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is completely off theground.5. Remove
Stowing the tire and jack1. Fully collapse the jack and place the foam cover on the base of thejack2. Fold the lug wrench socket and snap it into the
AM/FM STEREO/ SINGLE CD SOUND SYSTEM (IF EQUIPPED)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various
WHEEL LUG NUT TORQUE SPECIFICATIONSRetighten the lug nuts to the specified torque at 500 miles (800 km)after any wheel disturbance (tire rotation, cha
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE CAREImproper or inadequate vehicle maintenance can also cause tires to wearabnormally. Here are some of the important maintenance items:Tire wear
Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t
The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear.Tire rotationRotating your tire
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can
Balance: Press to adjust the audio between the left and right speakers.Use/ / SEEK .Fade: Press to adjust the audio between the front and rear speaker
tires and chains. If you need to use snow tires and chains, it isrecommended that steel wheels are used of the same size andspecifications as those or
Vehicle Curb Weight – is the weight of your new vehicle when youpicked it up from your dealer plus any aftermarket equipment.Payload – is the combined
Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue loador king pin w
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).
mandatory options, no cargo (internal or external), a tongue load of10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), a
average 220 pounds each and the golf bags weigh approximately30 pounds each. Is there enough load capacity to carry you, 4 ofyour friends and all the
Preparing to towUse the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. See your dealer or a reliable trai
Driving while you towWhen towing a trailer:• Turn off the speed control. The speed control may shut offautomatically when you are towing on long, stee
RECREATIONAL TOWINGFollow these guidelines for your specific powertrain combination to towyour vehicle for personal travel (such as behind a recreatio
12. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, press andhold a preset button until sound returns.13. Scan: Press
STARTINGPositions of the ignition1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and a
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
• Make sure the gearshift lever is inP (Park).3. Turn the key to 3 (ON) withoutturning the key to 4 (START).Make sure the corresponding lights illumin
Starting the engine1. Turn the key to 3 (ON) withoutturning the key to 4 (START).2. Turn the key to 4 (START), thenrelease the key as soon as theengin
BRAKESOccasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-o
Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th
TRACTION CONTROL姟 (IF EQUIPPED)Your vehicle may be equipped with a Traction Control娂 system. Thissystem helps you maintain the stability and steerabil
STEERINGTo prevent damage to the power steering system, never hold the steeringwheel at its furthest turning points (until it stops) for more than a f
2. Remove the console panel byopening the armrest, grasping thepanel firmly, then pulling up. Thiswill allow access to the gearshiftassembly.3. Locate
Understanding the gearshift positions of theelectronically-controlled Continuously Variable Transaxle (CVT)The CVT is a fully automatic transaxle that
Seating and Safety Restraints 106Seating 106Safety restraints 118Air bags 131Child restraints 144Tires, Wheels and Loading 158Tire Information 159Tire
PREMIUM/AUDIOPHILE IN-DASH SIX CD/MP3 SOUND SYSTEM(IF EQUIPPED)1./ Tune/Disc selector:Press to manually go up or downthe radio frequency or to select
To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)Always set the parking brake full
This system is not designed to prevent contact with small ormoving objects. The system is designed to provide a warning toassist the driver in detecti
indicator light on the control will illuminate when the system is turnedoff. If the indicator light illuminates when the RSS is not turned off, itmay
Basic operating principles• Drive slower in strong crosswinds which can affect the normal steeringcharacteristics of your vehicle.• Be extremely caref
If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly.See your dealer or a qua
Do not use L (Low) gear when driving through sand.Under severe operating conditions, the A/C may cycle on and off toprotect overheating of the engine.
Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should
Avoid sudden applications of power and quick changes of direction onsnow and ice. Apply the accelerator slowly and steadily when startingfrom a full s
stall. Driving through deep water where the transmission venttube is submerged may allow water into the transmission andcause internal transmission da
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Bass: Press to adjust the bass setting. Use / / SEEK .Treble: Press to adjust the treble setting. Use/ / SEEK .Balance: Press to adjust the audio betw
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
This switch is located under theright-hand side of the glovecompartment.To reset the switch:1. Turn the ignition OFF.2. Check the fuel system for leak
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge5A Tan Tan ———7.5A Brown Brow
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionF1 20A High beamsF2 15A Interior lamps (Courtesy anddemand lamps), Delayeda
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionF16 10A Rear defroster indicator, HeatedmirrorsF17 30A Rear defrosterF18 10
Always disconnect the battery before servicing high currentfuses.Always replace the cover to the power distribution box beforereconnecting the battery
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription9 — Not used10 40A* Anti-lock Brake System (ABS)(Motor)11 30A* Starter12 30A* Powertr
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription33 30A* Driver seat motors, Memorymodule34 30A* Ignition switch (to SJB)35 — Not used
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription58 High currentrelayWipers59 — Not used60 1A Diode PCM61 1A Diode PCM* Cartridge Fuse
Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,
Compression: Available only in CD mode, brings soft and loud CDpassages together for a more consistent listening level.Repeat: Available only in CD mo
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, flatbed transport vehicle or a car hauling trailer) yourvehic
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai
Board membershipThe Board consists of:• Three consumer representatives• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa
14. Seek: Press to access theprevious strong station or track.15. AM/FM: Press to select AM/FMfrequency band.16. ON/OFF/Volume: Press to turnON/OFF. T
Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a
If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips.• Always
• 3.0L Duratec engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTIC (NON-PAINTED)
Do not use sharp objects, such as a razor blade, to clean theinside of the rear window or to remove decals, as it may causedamage to the rear window d
Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing.Do not use chemical solvents or
FORD, LINCOLN AND MERCURY CAR CARE PRODUCTSYour Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect i
RADIO RECEPTION FACTORSThere are three factors that can effect radio reception:• Distance/strength: The further you travel from an FM station, theweak
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column.2. Go to th
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.0L DOHC V6 DURATEC ENGINE1. Engine coolant reservoir2. Power steering fluid reservoir3. Brake fluid
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.•
• If required, add engine oil to theengine. Refer to Adding engineoil in this chapter.• Do not overfill the enginewith oil. Oil levels above thismark
Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oil.Only use oils “Certified For Gasoline Engines” by t
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
DVD player controls1. MAIN control• NEXT — Press to access the next track on the CD, the next chapteron the DVD, or to go up in cursor mode.• PREV — P
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur
To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. Thecooling system is under press
7. Pull off metal pin and removecoolant bleed plug from thethermostat housing.8. Add coolant/water mixturethrough the thermostat housingopening until
9. Install the thermostat housingbleed plug. Install metal pin bypushing into the slot.After any coolant has been added, check the coolant concentrati
Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsDo not overfill the fuel tank. The pressure in an overfilled tankmay cause leak
• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek med
1. Turn the engine off.2. Carefully turn the filler cap counterclockwise 1/4 of a turn until itstops.3. Pull to remove the cap from the fuel filler pi
Repairs to correct the effects of using a fuel for which your vehicle wasnot designed may not be covered by your warranty.Octane recommendationsYour v
6. AUX controlPress to switch DVD player from play mode to auxiliary mode.7. Auxiliary jacksInput jacks for standard video game players.8. STOP/EJECT
If you have run out of fuel:• You may need to cycle the ignition from OFF to ON several times afterrefueling, to allow the fuel system to pump the fue
For consistent results when filling the fuel tank:• Turn the engine/ignition switch to the off position prior to refueling,an error in the reading wil
Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin
• Adding certain accessories to your vehicle (for example bugdeflectors, rollbars/light bars, running boards, ski/luggage racks) mayreduce fuel econom
emission control, such non-Ford parts should be equivalent to genuineFord Motor Company parts in performance and durability.Do not park, idle, or driv
driving cycles without these or any other temporary malfunctionspresent, the Check engine/Service engine soon light should turn off. (Adriving cycle c
1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center o
TRANSAXLE FLUIDChecking automatic transaxle fluidDo not use supplemental transaxle fluid additives, treatments orcleaning agents. The use of these mat
Replace the PCV valve with one that meets Ford material anddesign specifications for your vehicle, such as a Motorcraft orequivalent replacement part.
Fluid Ford PartNameApplication CapacityPower steeringfluidMotorcraftMERCON威 ATF3.0L engine Between MAXand MIN onreservoirAutomatictransaxle fluidMotor
• Press the REV control to movethe cursor left one position• Press the FWD control to movethe cursor right one positionNext/Previous controlThe NEXT (
LUBRICANT SPECIFICATIONSItemsFord PartName orequivalentFord PartNumberFordSpecificationBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeF
ItemsFord PartName orequivalentFord PartNumberFordSpecificationPower TransferUnitMotorcraft SAE75W-90 FuelEfficient HighPerformanceRear AxleLubricantX
ENGINE DATAEngine 3.0L-DOHC V6 engineDisplacement 183 cubic inchesRequired fuel 87 octaneFiring order 1–4–2–5–3–6Spark plug gap 1.32–1.42mm (0.052–0.0
52341REVIEW COPY2005 Freestyle (219), Owners Guide (post-2002-fmt) (own2002),Market: USA_English (fus)Maintenance and Specifications273
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
1. World manufacturer identifier2. Brake type and gross vehicleweight rating (GVWR)3. Vehicle line, series, body type4. Engine type5. Check digit6. Mo
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford
Electrochromic mirror w/compass and homelinkElectrochromic mirror w/compass and temperature displayElectrochromic mirror w/compass, temperature displa
the front or rear axle (GVWR or GAWR as indicated on the SafetyCompliance Certification label). Consult your dealer for specific weightinformation.• T
AAccessory delay ...66Air bag supplemental restraintsystem ...131–132, 139, 141and child safety seats ...
CD play modePress NEXT during CD play toadvance to the next track. If youpress NEXT while the last track isplaying, the system will wrap aroundto the
plastic parts ...236washing ...234waxing ...234wheels ...
Exhaust fumes ...193FFluid capacities ...268Foglamps ...52Four-Wheel Dr
Keyspositions of the ignition ...190LLampsautolamp system ...51bulb replacementspecifications chart ...56dayt
Roadside assistance ...209Roof rack ...90SSafety Belt Maintenance ...130Safety belts (seeSafet
Turn signal ...55VVehicle dimensions ...272Vehicle Identification Number(VIN) ...
285
286
288
Remote control1. REWIND controlPress to reverse the direction of the DVD movie.2. FAST FORWARD controlPress to advance the direction of the DVD movie.
Maintenance and Specifications 240Engine compartment 242Engine oil 243Battery 247Fuel information 256Part numbers 267Refill capacities 268Lubricant sp
8. VOLUME controlPress (+) to increase or (-) to decrease the volume level over vehiclespeakers.Dual play modePress the radio preset controls 2and 4 a
Battery replacementBatteries are provided with theremote control unit. Since allbatteries have a limited shelf life,replace them when the remotecontro
To install the batteries, lightly pressdown on top of the left earpiece, asshown to the right, and slide thecover off.When replacing the batteries, us
Liquid Crystal Display (LCD) flip-down screenThe LCD screen rotates down and can be adjusted to your desiredviewing angle. When not in use, rotate the
• When the temperature of the DVD player becomes too hot, the hightemperature sensor circuit stops machine operation. DVD/CD HOT willbe displayed on t
Removing a CD/DVD (while playing)1. Press the STOP/EJECT control to stop playback if a disc is playing.2. Press the STOP/EJECT control again to eject
2. DVD/CD chapter/track number.3. MEDIA COUNTER — displays current viewing time of desired media.(MINUTES : SECONDS).4. Audio track number.5. Audio tr
Whenever a warning notice is received, the radio volume will belowered to a volume that will allow the tones to be heard. Theradio volume will return
Humidity and moisture condensationMoisture in the air will condense in the DVD player under extremelyhumid conditions or when moving from a cold to a
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED)1.Defrost: Distributes outside air through the windshield defrosterand demister vents. Can be used
9. : Distributes air through the instrument panel vents.10. Manual override controls: Allows you to manually select whereairflow is directed. To retur
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS (IF EQUIPPED)1.Defrost: Distributes outside air through the windshield defrosterand demister
8. Airflow direction control: Press to toggle through the airdistribution modes listed below. The selected mode will be shown in thedisplay.: Distribu
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH REARPASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED)1.Defrost: Distributes outside air through the win
7. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. Engagesautomatically in
DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS AND REAR PASSENGER COMPARTMENTCLIMATE CONTROL (IF EQUIPPED)1.Defrost: Distributes outside air
down the interior of the vehicle and may also help reduce undesiredodors from reaching the interior of the vehicle. Recirculation can beengaged manual
temperature also when DUAL is disengaged. Recommended temperaturerange is 72° to 75° Fahrenheit.18. AUTO: Press to engage automatic temperature contro
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
Do not place objects on top of the instrument panel as theseobjects may become projectiles in a collision or sudden stop.AUXILIARY CLIMATE CONTROL (IF
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola
5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamp switch to OFF. The headlampswill turn off.
High beamsPull the lever towards you, to thesecond detent, to activate. Pull thelever towards you again todeactivate.Flash to passPull toward you, to
AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident the alignment of yo
5. Locate the vertical adjuster oneach headlamp. Using a Phillips #2screwdriver, turn the adjuster eitherclockwise (to adjust down) orcounterclockwise
The map lamps are located on theoverhead console. Press the controlson either side of each map lamp toturn on the lamps.Your vehicle may also have rea
Function Number of bulbsTradenumberHigh-mount brake lamp 5 W5WFoglamp (if equipped) 2 H11 LLMap lamp 2 12V6WDome/reading lamps 6 578All replacement bu
Replacing front parking lamp/turn signal bulbs1. Make sure headlamp switch is in the OFF position, then open thehood.2. Reach behind the headlamp asse
Replacing stop/tail/turn/backup bulbsThe stop, tail, turn and backup lamp bulbs are located in the tail lampassembly. Follow the same steps to replace
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
Replacing license plate lamp bulbs1. Make sure the headlamp switch isin the OFF position.2. Remove the two screws from thelicense plate lamp assembly.
MULTI-FUNCTION LEVERWindshield wiper: For intermittentoperation, move control up oneposition.Adjust the rotary control to thedesired speed setting.Mis
Rear window wiper/washer controlsFor rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select:2 — One second
TILT STEERING WHEELTo adjust the steering wheel:1. Pull down and hold the steeringwheel release control.2. Move the steering wheel up ordown until you
Conversation mirror (if equipped)The conversation mirror allows the driver to view the rear seating area.This does not replace the rear view mirror.Pu
POWER WINDOWSDo not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injurethemselves.W
If the switch is pressed and held to the normal open or ONE TOUCHDOWN position during a ONE TOUCH UP event, the window will stop. If,after 1/2 second
MIRRORSPower side view mirrorsTo adjust your mirrors:1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise
POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is
3. Press the SET + control andrelease it.4. Take your foot off the acceleratorpedal.5. The indicatorlight on theinstrument cluster will turn on.Note:•
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental restraint
Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET + controluntil you get to the desiredspeed,
Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal or pressCNCL (Cancel). This will noterase your veh
In any mode:• Press VOL up or down to adjustthe volume.• Press MUTE to mute the volume.MOON ROOF (IF EQUIPPED)You can move the glass panel of the moon
with a single built-in device. This feature will learn the radio frequencycodes of most transmitters to operate garage doors, entry gate operators,sec
3. Simultaneously press and holdboth the HomeLink威 and hand-heldtransmitter button. Do not releasethe buttons until step 4 has beencompleted.Some entr
Gate Operator & Canadian ProgrammingDuring programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time for
Erasing HomeLink姞 buttonsTo erase the three programmedbuttons (individual buttons cannotbe erased):• Press and hold the two outerHomeLink威 buttons unt
Info menuThis control displays the followingcontrol displays:• Odometer• Distance to Empty• Average Fuel Economy• Trip Odometer• Fuel Used• Trip Elaps
miles traveled (kilometers traveled by liters used), your figure may bedifferent than displayed for the following reasons:• Your vehicle was not perfe
Usually, when something affects the compass readings, the compass willcorrect itself after a few days of operating your vehicle in normalconditions. I
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
5. Press and hold the RESET untilthe message center display changesto show the current zone setting.6. Release the RESET control, thenslowly press RES
Language1. Select this function from theSETUP menu for the currentlanguage to be displayed.2. Pressing the RESET controlcycles the message center thro
5. CHARGING SYSTEM6. BRAKE SYSTEM7. PARK BRAKE STATUS8. OIL PRESSURE9. WASHER FLUID LEVEL10. BRAKE FLUID LEVEL11. COOLANT LEVEL12. TRANSMISSION STATUS
Warnings StatusPark brake engaged RELEASE PARK BRAKE will bedisplayedCheck engine temp Warning returns after 10 minutesReduced engine powerETC-Engine
CHECK ENGINE TEMPERATURE. Displayed when the enginecoolant is overheating. Stop the vehicle as soon as safely possible, turnoff the engine and let it
LIFTGATE AJAR (if equipped). Displayed when the liftgate is notcompletely closed.TRUNK AJAR (if equipped). Displayed when the trunk is notcompletely c
2. Press and release the RESETcontrol to display “HOLD RESETTO CONFIRM”.3. Press and hold the RESETcontrol to display OIL LIFE SET TO100%. Your oil li
• Fuel cap sensor• Seat belt sensor• Park brake• Oil pressure sensorContact your dealer as soon as possible if these messages occur on aregular basis.
CELL PHONE USEThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri
CARGO AREA FEATURESCargo net (if equipped)The cargo pouch net secureslightweight objects in the cargoarea. Attach the net to the anchorsprovided. Do n
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
LUGGAGE RACKMaximum load is 125 lbs (57 kg) on the roof rack structure, or 100 lbs(45 kg) on the roof panel, evenly distributed. If it is not possible
KEYSOne key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency.Your keys are programmed to your v
1. Place the key in the ignition and turn the ignition to the 3 (RUN)position.2. Press the power door unlock control on the door panel three times.3.
(1) This device may not cause harmful interference, and (2) This devicemust accept any interference received, including interference that maycause und
The inside lights will not turn off if:• they have been turned on using the dimmer control or• any door is open.The battery saver feature will turn of
2. Press the SET control on thedriver’s door panel.3. Within 5 five seconds, press the 1or 2 control on the driver’s doorpanel to which you would like
5. Snap the two halves back together.Note: Replacement of the battery will not cause the remote transmitterto become deprogrammed from your vehicle. T
9. The doors will lock, then unlock, to confirm that the programmingmode has been exited.Illuminated entryThe interior lamps illuminate when the remot
KEYLESS ENTRY SYSTEMYou can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• activate or deactivate theautolock feature.
Tips:• Do not set a code that uses five of the same number.• Do not use five numbers in sequential order.• The factory set code will work even if you
Commentaires sur ces manuels