Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 14Entertainment Systems 16AM/FM stereo with single CD 16AM/FM stereo with in-da
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly move the seat forwardand back to m
1. Position the child safety seat on the seat cushion.2. Route the child safety seat tether strap over the back of the seat.On hatchbacks, the removab
5. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safetyseat may not be retained properlyin the even
unless a child seat at an outboard rear seat is attached to one of theselower anchors. Install a child seat onto the lower anchors at the centerrear s
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
• Extra load: A class of P-metric or Metric tires designed to carry aheavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires].Increasing the
Inspecting your tiresPeriodically inspect the tire treads for uneven or excessive wear andremove stones, nails, glass or other objects that may be wed
higher than the manufacturer’s recommended cold inflation pressurewhich can be found on either the tire label or certification label which islocated o
TIRE REPLACEMENT REQUIREMENTSYour vehicle is equipped with tires designed to provide a safe ride andhandling capability.Only use replacement tires and
Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interiorfloor coverings or other
Temporary spare tire informationThe temporary spare tire for your vehicle is labeled as such. It is smallerthan a regular tire and is designed for eme
Dissimilar spare tire/wheel information (if equipped)Failure to follow these guidelines could result in an increasedrisk of loss of vehicle control, i
Tire change procedure1. Park on a level surface, activatehazard flashers and set the parkingbrake.When one of the front wheels is off the ground, the
4. On 3–door models, unsnap andremove the access door (ifequipped) to access the properjacking points.5. Loosen each wheel lug nutone-half turn counte
6. The vehicle jacking points aredepicted on the yellow warning labelon the jack shown here. Dependingon which tire is to be changed,locate the jack a
Bolt size Wheel lug nut torque*lb.ft. N•mM12 x 1.5 92 125* Torque specifications are for nut and bolt threads free of dirt andrust. Use only Ford reco
2. 215: Indicates the nominal width of the tire in millimeters fromsidewall edge to sidewall edge. In general, the larger the number, thewider the tir
Letter rating Speed rating - mph (km/h)Note: For tires with a maximum speed capability over 149 mph (240km/h), tire manufacturers sometimes use the le
• Temperature: The temperature grades are A (the highest), B and C,representing the tire’s resistance to the generation of heat and itsability to diss
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
Safety belt: Reminds you to fastenyour safety belt. A chime will alsosound to remind you to fasten yoursafety belt.Charging system: Illuminates whenth
TIRE CAREImproper or inadequate vehicle maintenance can also cause tires to wearabnormally. Here are some of the important maintenance items:Tire wear
Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t
Wheel misalignment in the front or the rear can cause uneven and rapidtreadwear of your tires and should be corrected by a qualified technicianat a Fo
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can
SNOW TIRES AND CHAINSSnow tires must be the same size and grade as the tires youcurrently have on your vehicle.The tires on your vehicle have all weat
VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic
Note: For trailer towing information refer to Trailer towing found inthis chapter or the RV and Trailer Towing Guide provided by yourdealership.GVW (G
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle.3. Subtract the combined weight of the driver and pas
1400 – (2 x 220) – (9 x 100) = 1400 – 440 – 900 = 60 lbs. Metricconversion; 636 kg – (2 x 100) – (9 x 45) = 636 – 200 – 405 = 31 kg.Now you have the l
Low fuel: Illuminates when the fuellevel in the fuel tank is at or nearempty (refer to Fuel gauge in thischapter).Speed control (if equipped):Illumina
Towing trailers beyond the maximum recommended gross trailerweight exceeds the limit of the vehicle and could result inengine damage, transaxle damage
Driving while you towWhen towing a trailer:• Turn off the speed control. The speed control may shut offautomatically when you are towing on long, stee
RECREATIONAL TOWINGFollow these guidelines for your specific powertrain combination to towyour vehicle with all four wheels on the ground (such as beh
STARTINGPositions of the ignition1. LOCK, locks the steering wheel,automatic transaxle gearshift leverand allows key removal.2. OFF, shuts the engine
If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf
If starting a vehicle with a manualtransaxle:1. Make sure the parking brake isset.2. Push the clutch pedal to the floor.• Turn the key to 3 (ON) witho
Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced.• If the driver’s safety
BRAKESOccasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-o
Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake
During Traction Control娂 operation,the traction control active light willilluminate, you may hear an electricmotor type of sound coming fromthe engine
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
If the steering wanders or pulls, check for:• an improperly inflated tire• uneven tire wear• loose or worn suspension components• loose or worn steeri
Do not drive your vehicle until you verify that the brakelampsare working.Always set the parking brake fully and make sure the gearshift islatched in
To put your vehicle in gear:• Start the engine• Depress the brake pedal• Move the gearshift lever into the desired gearTo put your vehicle in P (Park)
2 (Second)This position allows for second gear only.• Provides engine braking.• Use to start-up on slippery roads.• To return to D (Overdrive), move t
To start the vehicle:1. Make sure the parking brake is fully set.2. Press the clutch pedal to the floor, then put the gearshift lever in theneutral po
Parking your vehicle1. Apply the brake and shift into the neutral position.2. Fully apply the parking brake, then shift into 1 (First).3. Turn the ign
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
USING ROADSIDE ASSISTANCEComplete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, th
FUEL PUMP SHUT-OFF SWITCHThis device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt.After an
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
Odometer: Registers the total miles(kilometers) of the vehicle.Trip odometer: Registers the miles(kilometers) of individual journeys.To reset, depress
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionR17 — Starter relayR18 – Rear wiper intermit
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description33 20A Horn34 20A Stand-alone decklid relay (sedanonly), Power sunroof35 7.
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description59 7.5A Light switch (headlamps)60 7.5A Air bag module61 7.5A PATS modules,
To remove a fuse, use the fuse puller tool provided on the powerdistribution box cover.The high-current fuses are coded as follows:Fuse/RelayLocationF
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription11 30A Anti-lock Brake System (ABS)(pumps)12 15A Fuel pump13 — Not used14 — Not used1
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescriptionR10 — Cooling fan relayR11 — A/C clutch solenoid relayR12 — DRL relayR13 — Fog lamps
3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake onboth vehicles
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
• 2.0L/2.3L engines5. Ensure that the cables are clear of fan blades, belts, moving parts ofboth engines, or any fuel delivery system parts.Jump start
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
AM/FM STEREO WITH SINGLE CD — PREMIUM (IF EQUIPPED)AM/FM STEREO WITH SINGLE CD/MP3 — PREMIUM(IF EQUIPPED)REVIEW COPY2005 Focus (foc), Owners Guide (po
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli
Ford Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf you own a Lincoln vehicle and are away f
In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or
• available free to owners and lessees of qualifying Ford Motor Companyvehicles.The Dispute Settlement Board may not be available in all states. FordM
• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Board membership are recruited and trained byan independent consulting fi
before the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral presentationmay be
The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have
GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.
1. / Tune selector: Press tomanually increase/decrease theradio frequency.2. Phone/mute: Press to mute theplaying media. Press again to returnto the p
Or call:For a free publication catalog, order toll free: 1-800-782-4356Monday-Friday 8:00 a.m. - 6:00 p.m. ESTHelm, Incorporated can also be reached b
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips.• Always
• 2.0L and 2.3L I4 EnginesPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your
INSTRUMENT PANEL AND CLUSTER LENSClean the instrument panel with a damp cloth, then dry with a dry cloth.• Avoid cleaners or polish that increase the
LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• To clean, use a soft cloth with Motorcraft
Motorcraft Deluxe Leather and Vinyl Cleaner (not available in Canada)(ZC-11–A)Motorcraft Bug and Tar Remover (ZC-42)Motorcraft Extra Strength Upholste
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
Working with the engine on• Automatic transmission:1. Set the parking brake and shift to P (Park).2. Block the wheels.• Manual transmission:1. Set the
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.0L/2.3L I4 Engines1. Power steering fluid reservoir2. Engine oil filler cap3. Brake/Clutch fluid res
Speed sensitive volume: Radio volume automatically adjusts accordingto vehicle speed to compensate for road and wind noise. Press the Tuneselector (/
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
• 2.0L/2.3L engines6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.• If the oil level is between the MIN and MAX marks th
To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level indicator and/or the engine oil filler cap removed.Engine oil and filt
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If
Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyeswhen working near
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
• Add Motorcraft Premium Gold Engine Coolant(yellow-colored), VC-7–A (U.S., except CA and OR), VC-7–B(CA and OR only), meeting Ford SpecificationWSS-M
2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly tu
Fill your engine coolant reservoir as outlined in Adding engine coolantin this section.Severe climatesIf you drive in extremely cold climates (less th
10. Fast forward: Press and holdto manually advance the CD.11. Rewind: Press and hold tomanually reverse the CD.12. Memory presets: To set astation: S
How fail-safe cooling worksIf the engine begins to overheat:• The engine coolant temperaturegauge will move to the red (hot)area.• The “Check Engine”
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsDo not overfill the fuel tank. The pressure in an overfilled tankmay cause leak
• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek med
Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1/4 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref
Repairs to correct the effects of using a fuel for which your vehicle wasnot designed may not be covered by your warranty.Octane recommendationsYour v
If you have run out of fuel:• You may need to cycle the ignition from OFF to ON several times afterrefueling, to allow the fuel system to pump the fue
For consistent results when filling the fuel tank:• Turn the engine/ignition switch to the off position prior to refueling,an error in the reading wil
Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin
• Adding certain accessories to your vehicle (for example bugdeflectors, rollbars/light bars, running boards, ski/luggage racks) mayreduce fuel econom
If other than Ford, Motorcraft or Ford-authorized parts are used formaintenance replacements or for service of components affectingemission control, s
Seating and Safety Restraints 63Seating 63Safety restraints 68Air bags 83Child restraints 92Tires, Wheels and Loading 104Tire Information 105Tire Infl
AM/FM STEREO WITH IN–DASH 6CD —PREMIUM /AUDIOPHILE(IF EQUIPPED)1./ Tune Selector: Press tomanually increase/decrease theradio frequency when in tuner
3. The fuel cap may not have been securely tightened.These temporary malfunctions can be corrected by filling the fuel tankwith good quality fuel and/
CHECKING AND ADDING POWER STEERING FLUIDCheck the fluid. Refer to theScheduled Maintenance Guide forservice maintenance schedules.1. Start the engine
CLUTCH FLUID (IF EQUIPPED)The clutch master cylinder andbrake master cylinder are part ofthe same system; both are refillablethrough the brake master
5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. Ifnecessary, refer to Identifying components in the engine compartmentin this
Use of a non-approved automatic transmission fluid may causeinternal transaxle component damage.If necessary, add fluid in 250 mL (1/2 pint) increment
MOTORCRAFT PART NUMBERSComponent 2.0L I4 engine 2.3L I4 engineAir filter element N/A (Lifetime)1N/A (Lifetime)1Fuel filter FG-1081 FG-1081Oil filter F
REFILL CAPACITIESFluid Ford Part Name Application CapacityBrake fluidand clutchfluidMotorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to
2Ensure the correct automatic transmission fluid is used. Transmissionfluid requirements are indicated on the dipstick or on the dipstick handleor as
LUBRICANT SPECIFICATIONSItemFord PartName orEquivalentFord PartNumberFordSpecificationBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFl
ItemFord PartName orEquivalentFord PartNumberFordSpecificationEngine coolant MotorcraftPremium GoldEngine Coolant(yellow-colored)VC-7-A (U.S.,except C
To activate RDS, press and hold MENU until RDS ON or RDS OFFappears in the display. Press MENU again to continue to FIND andSHOW functions. Press the
VEHICLE DIMENSIONSVehicledimensionsSedan - inches(mm)3dr/5dr -inches (mm)Wagon -inches (mm)(1) Overalllength175.2 (4450) 168.5 (4279) 178.5 (4533)(2)
• 3dr/5drREVIEW COPY2005 Focus (foc), Owners Guide (post-2002-fmt) (own2002),Market: USA_English (fus)Maintenance and Specifications211
• WagonIDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be a
Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford
Leather wrapped steering wheelsScuff platesSpeed controlLifestyleBike racksCargo organization and managementPeace of mindFirst aid and highway safety
AAir bag supplemental restraintsystem ...83, 90and child safety seats ...85description ...
Clutchfluid ...201–202operation while driving ...143recommended shift speeds ...144Consoleoverhead ...
choosing the right fuel ...193comparisons with EPA fueleconomy estimates ...198detergent in fuel ...194filling
Lubricant specifications ...208–209Lug nuts ...114MManual transaxlelubricant specifications ...209Manual trans
4. Aux: Press to access theAuxiliary mode. If no auxiliarysources are available, NO AUXAUDIO will be displayed.5. Seek up: Press for next strongstatio
Starting yourvehicle ...133–134, 136jump starting ...155Steering wheeltilting ...
221
222
223
224
14. Seek down: Press for previousstrong station or CD track. Pressand hold for continuous seekfunctionality.15. AM/FM: Press to togglebetween AM/FM1/F
REMOTE AUDIO STEERING COLUMN CONTROLS (IF EQUIPPED)The remote audio steering column controls may be used to select radio or CDmode. The following func
RADIO RECEPTION FACTORSThere are three factors that can effect radio reception:• Distance/strength: The further you travel from an FM station, theweak
HEATER ONLY SYSTEM(IF EQUIPPED)1. Air flow selections: Controlsthe direction of the airflow in thecabin. See the following for a briefdescription on e
To aid in side window defogging/demisting in cold weather:1. Select.2. Modulate the temperature control to maintain comfort.3. Set the fan speed to th
4. Recirculated air: Press to activate/deactivate air recirculationin the vehicle cabin. Recirculated air may reduce the amount of timerequired to coo
REAR WINDOW DEFROSTERThe rear defroster control is located on the instrument panel.Press the rear defroster control to clear the rear window of thin i
Maintenance and Specifications 177Engine compartment 179Engine oil 180Battery 183Fuel information 191Part numbers 205Refill capacities 206Lubricant sp
HEADLAMP CONTROLTurns the lamps off.Turns on the parkinglamps, instrument panel lamps,license plate lamps and tail lamps.Turns the headlamps on.Foglam
High beamsPull the lever towards you toactivate. Pull the lever towards youagain to deactivate.Flash to passPull toward you slightly to activateand re
• (4) Horizontal reference line2. Measure the height from thecenter of your headlamp to theground and mark an 8 foot (2.4meter) horizontal reference l
INTERIOR LAMPSDome lampsThe dome lamp is equipped with acontrol switch that will illuminatewhen:• the doors are closed and theswitch is in the on posi
Function Trade numberHeadlamps HB5Park and turn lamp (front) 3157AK or 3157ASide marker lamp (front) GE194Foglamps (if equipped) H11Stop/turn and tail
Replacing front parking lamp/turn signal bulbs1. Make sure the headlamp controlis in the OFF position and open thehood.2. Remove the bulb socket from
Replacing tail/brake/backup lights and turn signal bulbs (sedan)1. Make sure the headlamp controlis in the OFF position and thenopen the trunk.2. From
Replacing side marker bulbs1. Make sure the headlamp controlis in the OFF position.2. Reach under the front fender,grasp the bulb socket and turn itco
3dr & 5dr and wagon1. Make sure the headlamp controlis in the OFF position.2. Remove the screws using a TorxT20 screwdriver and then removethe pla
Replacing interior lamps1. Make sure the headlamp switch isin the OFF position.2. Switch off the interior lamps(middle switch position).3. Pry out the
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
MULTI-FUNCTION LEVERWindshield wiper: Move the leverdown for a single wipe.For intermittent operation, movecontrol up one position and adjustthe rotar
Changing the wiper blades1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas
HORNPress the steering wheel pad. Thehorn can be operated when theignition is off.OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehicle’s overh
• Place the Velcro hook onto theside of the aftermarkettransmitter opposite of thebutton.• Place the transmitter into storagecompartment, button down.
Cigar lighter (if equipped)Do not plug optional electrical accessories into the cigarette lightersocket.Do not hold the lighter in with your hand whil
MIRRORSPower side view mirrorsTo adjust your mirrors:1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise
Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas
Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RES contro
• Depress the brake pedal until thedesired vehicle speed is reached,press the SET ACCEL control.Turning off speed controlPress the speed control OFFco
To close:• To close, press and release the front portion of the control.To vent:• To tilt the moon roof into the vent position (when the glass panel i
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
REMOTE LUGGAGE COMPARTMENT RELEASE (IF EQUIPPED)To open the luggage compartment,press the control on the instrumentpanel.The control does not function
LUGGAGE COVERModels with rear hatchDetach the lifting straps on theliftgate. Release the cover at thesides and pull it out horizontallywithout tilting
• To open the liftgate, unlock thewagon (with the power door locksor the remote entry key fob) andpush the button next to thelicense plate.•To close t
KEYSThe key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency.You
1. Turn the ignition to the 3 (ON)position.2. Press the power door unlockcontrol three times.3. Turn the ignition from 3 (ON)position to the 2 (OFF) p
Adults are advised to familiarize themselves with the operation andlocation of the release handle.To open the luggage compartmentdoor (lid) from withi
REMOTE ENTRY SYSTEM (IF EQUIPPED)This device complies with part 15 of the FCC rules and with RS-210 ofIndustry Canada. Operation is subject to the fol
2. With the all-door remote entry, press and release again withinthree seconds to unlock all the doors.The remote entry system activates the illuminat
• Ensure that the trunk is closed and latched before driving yourvehicle. Failure to properly latch the trunk may cause objects to fallout or block th
5. Snap the two halves back together.Note: Replacement of the battery will not cause the remote transmitterto become deprogrammed from your vehicle. T
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEMSecuriLock娂 passive anti-theft system is an engine immobilizationsystem. This system is designed to help prevent
Programming spare keysYou can program your own coded keys to your vehicle. Please read andunderstand the entire procedure before you begin.Tips:• A ma
11. Your new, unprogrammed key is now programmed.If the key has been successfully programmed it will start the vehicle’sengine and the theft indicator
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Adjusting the front manual seatPull the lever located under thefront edge of the seat to move theseat forward or backward.Turn the handle to adjust th
Heated seats (if equipped)The heated seats switch is located on the center console.To operate the heated seats:• Push control to activate.• Push again
On three door models, front safetybelts should be pulled backwards toallow easier entry to or exit fromthe rear seats.Do not place objects behind the
Folding the rear seat back forward3–door/5–door and wagonRemove the head restraints (ifequipped) of the rear seats andstow them on the floor behind th
Folding the seat cushion and seatback forwardFold the seat cushion forward.Remove the head restraint(s) (ifequipped) of the rear seat, and foldthe sea
• Restraint system warning light and back-up tone.• The electrical wiring for the air bags, crash sensor(s), safety beltpretensioners, front safety be
Event Data RecordingOther modules in your vehicle — event data recorders — are capable ofcollecting and storing data during a crash or near crash even
Front passenger sensing systemFor air bags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occ
Front safety belt pretensionersThe safety belt pretensioners are designed to tighten the safety beltsfirmly against the occupant’s body during a colli
Safety belt precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injury, mak
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
Automatic locking modeWhen to use the automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to
How to disengage the automatic locking modeFord Motor Company recommends that all passenger safety beltassemblies and attaching hardware should be ins
Front safety belt height adjustmentAdjust the height of the shoulderbelt so the belt rests across themiddle of your shoulder.To adjust the shoulder be
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war
If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2minutes h
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
Reasons given... Consider...“I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to infla
The driver and front passenger BeltMinder娂 features can bedeactivated/activated by performing the following procedure:Before following the procedure,
Safety belt extension assemblyIf the safety belt is too short when fully extended, there isa8inch(20cm) safety belt extension assembly that can be add
AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The supplemental restraint system is designed to work with the safetybelt to help protect the driver and ri
All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bagsupplemental restraint system (
Children and air bagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rea
The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burn
• diagnostic module.• and the electrical wiring which connects the components.The diagnostic module monitors its own internal circuits and thesuppleme
When the front passenger seat isoccupied and the sensing systemhas turned off the passenger’sfrontal airbag, the ⬙passenger airbagoff⬙ or ⬙pass airbag
injury in a crash event. For example, if an occupant slouches, lies down,turns sideways, sits forward, leans forward or sideways, or puts one orboth f
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
If it is necessary to modify an advanced front airbag system toaccommodate a person with disabilities, contact the Ford CustomerRelationship Center at
Do not lean your head on the door. The side air bag could injureyou as it deploys from the side of the seatback.Do not attempt to service, repair, or
panel and occupant to further enhance the protection providedoccupants in side impact collisions.The air bag SRS is designed to activate when the vehi
Rear-facing child seats or infant carriers should never be placedin the front seats.Always transport children 12 years old and under in the backseat a
Follow all the important safety restraint and air bag precautions thatapply to adult passengers in your vehicle.If the shoulder belt portion of a comb
• Is the shoulder belt centered on the shoulder and chest?• Can the child stay seated like this for the whole trip?Types of booster seatsThere are two
The importance of shoulder beltsUsing a booster without a shoulder belt increases the risk of a child’shead hitting a hard surface in a collision. For
• Keep the buckle release button pointing up and away from the safetyseat, with the tongue between the child seat and the release button,to prevent ac
Children 12 and under should be properly restrained in the rearseat whenever possible.1. Position the child safety seat in aseat with a combination la
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
Commentaires sur ces manuels