Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 14Entertainment Systems 16AM/FM stereo with single CD 16AM/FM stereo with in-da
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
1. Position the child safety seat on the seat cushion.2. Route the child safety seat tether strap over the back of the seat.On hatchbacks, the removab
5. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safetyseat may not be retained properlyin the even
LATCH anchors for child seatinstallation have been provided inyour vehicle at the following locations:The anchors on both sides of thecenter of the re
STARTINGPositions of the ignition1. LOCK, locks the steering wheel,automatic transaxle gearshift leverand allows key removal.2. OFF, shuts the engine
If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf
If starting a vehicle with a manualtransaxle:1. Make sure the parking brake isset.2. Push the clutch pedal to the floor.• Turn the key to 3 (ON) witho
Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced.• If the driver’s safety
BRAKESOccasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-o
Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake
During Traction Control娂 operation,the traction control active light willilluminate, you may hear an electricmotor type of sound coming fromthe engine
Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interiorfloor coverings or other
• an improperly inflated tire• uneven tire wear• loose or worn suspension components• loose or worn steering components• improper steering alignmentA
Do not drive your vehicle until you verify that the brakelampsare working.Always set the parking brake fully and make sure the gearshift islatched in
To put your vehicle in gear:• Start the engine• Depress the brake pedal• Move the gearshift lever into the desired gearTo put your vehicle in P (Park)
2 (Second)This position allows for second gear only.• Provides engine braking.• Use to start-up on slippery roads.• To return to D (Overdrive), move t
To start the vehicle:1. Make sure the parking brake is fully set.2. Press the clutch pedal to the floor, then put the gearshift lever in theneutral po
Parking your vehicle1. Apply the brake and shift into the neutral position.2. Fully apply the parking brake, then shift into 1 (First).3. Turn the ign
Vehicle Curb Weight – is the weight of your new vehicle when youpicked it up from your dealer plus any aftermarket equipment.Payload – is the combined
Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue loador king pin w
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).
Safety belt: Reminds you to fastenyour safety belt. A chime will alsosound to remind you to fasten yoursafety belt.Charging system: Illuminates whenth
10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), and driver only (150 lbs. [68 kg]). Consult your dealership(or the RV
TRAILER TOWINGRefer to the following chart to determine how much weight your vehiclecan tow:Model Passengers/Luggageload - lbs. (kg)Maximum trailerwei
Preparing to towUse the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. See your dealer or a reliable trai
Driving while you towWhen towing a trailer:• Turn off the speed control. The speed control may shut offautomatically when you are towing on long, stee
RECREATIONAL TOWINGFollow these guidelines for your specific powertrain combination to towyour vehicle with all four wheels on the ground (such as beh
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
This switch is located in the frontpassenger’s footwell, behind the kickpanel access cover.To reset the switch:1. Turn the ignition OFF.2. Check the f
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey ———3A Violet Vio
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionR17 — Starter relayR18 – Rear wiper intermit
Low fuel: Illuminates when the fuellevel in the fuel tank is at or nearempty (refer to Fuel gauge in thischapter).Speed control (if equipped):Illumina
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description33 20A Horn34 20A Stand-alone decklid relay (sedanonly), Power sunroof35 7.
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description59 7.5A Light switch (headlamps)60 7.5A Air bag module61 7.5A PATS modules,
To remove a fuse, use the fuse puller tool provided on the powerdistribution box cover.The high-current fuses are coded as follows:Fuse/RelayLocationF
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription11 30A Anti-lock Brake System (ABS)(pumps)12 15A Fuel pump13 — Not used14 — Not used1
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescriptionR10 — Cooling fan relayR11 — A/C clutch solenoid relayR12 — DRL relayR13 — Fog lamps
• load the vehicle beyond maximum vehicle load rating listed on theSafety Compliance Label• tow a trailer• use tire chains• drive through an automatic
The usage of a dissimilar spare tire/wheel can lead to impairment of thefollowing:• Handling, stability and braking performance• Comfort and noise• Gr
If the vehicle slips off the jack, you or someone else could beseriously injured.2. Place gearshift lever in P (Park) (automatic transaxle) or R (Reve
5. Loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground.6. The vehicle jacking points
10. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lug nuttorque specifications later in thischapter for the proper l
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
Do not attempt to push-start your vehicle. Automatictransmissions do not have push-start capability; doing so maydamage the catalytic converter.Prepar
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto
• 2.0L/2.3L engines5. Ensure that the cables are clear of fan blades, belts, moving parts ofboth engines, or any fuel delivery system parts.Jump start
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli
Ford Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf you own a Lincoln vehicle and are away f
In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or
Odometer: Registers the total miles(kilometers) of the vehicle.Trip odometer: Registers the miles(kilometers) of individual journeys.To reset, depress
• available free to owners and lessees of qualifying Ford Motor Companyvehicles.The Dispute Settlement Board may not be available in all states. FordM
• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Board membership are recruited and trained byan independent consulting fi
before the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral presentationmay be
The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have
GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.
Or call:For a free publication catalog, order toll free: 1-800-782-4356Monday-Friday 8:00 a.m. - 6:00 p.m. ESTHelm, Incorporated can also be reached b
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips.• Always
• 2.0L and 2.3L I4 EnginesPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your
INSTRUMENT PANEL AND CLUSTER LENSClean the instrument panel with a damp cloth, then dry with a dry cloth.• Avoid cleaners or polish that increase the
AM/FM STEREO WITH SINGLE CD — PREMIUM (IF EQUIPPED)AM/FM STEREO WITH SINGLE CD/MP3 — PREMIUM(IF EQUIPPED)2005 Focus (foc)Owners Guide (post-2002-fmt)U
• To clean, use a soft cloth with Motorcraft Deluxe Leather and VinylCleaner (ZC-11–A). Dry the area with a soft cloth.• To help maintain its resilien
Ford Premium Car Wash Concentrate (F2SZ-19523–WC)Motorcraft Carlite Glass Cleaner (Canada only) (CXC-100)Motorcraft Spot and Stain Remover (ZC-14)Moto
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
Working with the engine on• Automatic transmission:1. Set the parking brake and shift to P (Park).2. Block the wheels.• Manual transmission:1. Set the
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.0L/2.3L I4 Engines1. Power steering fluid reservoir2. Engine oil filler cap3. Brake/Clutch fluid res
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
• 2.0L/2.3L engines6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.• If the oil level is between the MIN and MAX marks th
To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level indicator and/or the engine oil filler cap removed.Engine oil and filt
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If
Battery posts, terminals and related accessories contain lead andlead compounds. Wash hands after handling.Because your vehicle’s engine is electronic
1. / Tune selector: Press tomanually increase/decrease theradio frequency.2. Phone/mute: Press to mute theplaying media. Press again to returnto the p
coolant concentration should be maintained at 50/50 coolant and distilledwater, which equates to a freeze point of -34°F (-36°C). Coolantconcentration
Note: Automotive fluids are not interchangeable; do not use enginecoolant, antifreeze or windshield washer fluid outside of its specifiedfunction and
• Do not add extra inhibitors or additives to the coolant. Thesecan be harmful and compromise the corrosion protection of the enginecoolant.For vehicl
system may have a leak. Operating an engine with a low level of coolantcan result in engine overheating and possible engine damage.Recycled engine coo
• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i
4. Check the coolant level and replenish if low.Never remove the coolant reservoir cap while the engine isrunning or hot.5. Restart the engine and tak
Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforefueling your vehicle.• Alwa
Use the following guidelines to avoid static build-up when filling anungrounded fuel container:• Place approved fuel container on the ground.• DO NOT
Choosing the right fuelUse only UNLEADED FUEL. The use of leaded fuel is prohibited by lawand could damage your vehicle.Your vehicle was not designed
Many of the world’s automakers approved the World-wide Fuel Charterthat recommends gasoline specifications to provide improvedperformance and emission
selector ( / )or SEEK to turn off or select rates 1 through7. Rate 7 compensates the most volume at higher speeds.Setting the clock: Upon initial batt
The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fu
Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fuelecon
• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in your vehicle sche
• Do not turn off the ignition while your vehicle is moving, especially athigh speeds.• Have the items listed in your Scheduled Maintenance Guideperfo
government emission standards. The OBD-II system also assists theservice technician in properly servicing your vehicle. When the Checkengine/Service e
CHECKING AND ADDING POWER STEERING FLUIDCheck the fluid. Refer to theScheduled Maintenance Guide forservice maintenance schedules.1. Start the engine
CLUTCH FLUID (IF EQUIPPED)The clutch master cylinder andbrake master cylinder are part ofthe same system; both are refillablethrough the brake master
5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. Ifnecessary, refer to Identifying components in the engine compartmentin this
Use of a non-approved automatic transmission fluid may causeinternal transaxle component damage.If necessary, add fluid in 250 mL (1/2 pint) increment
• Treadwear 200 Traction AA Temperature AThese Tire Quality Grades are determined by standards that the UnitedStates Department of Transportation has
11. Rewind: Press and hold tomanually reverse the CD.12. Memory presets: To set astation: Select frequency bandAM/FM1/FM2; tune to a desiredstation, p
which all passenger car tires must meet under the Federal Motor VehicleSafety Standard No. 109. Grades B and A represent higher levels ofperformance o
• Rim: The metal support (wheel) for a tire or a tire and tube assemblyupon which the tire beads are seated.INFORMATION CONTAINED ON THE TIRE SIDEWALL
Note: You may not find this information on all tires because it is notrequired by federal law.7. H: Indicates the tire’s speed rating. The speed ratin
10. Tire Ply Composition and Material Used: Indicates the number ofplies or the number of layers of rubber-coated fabric in the tire tread andsidewall
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tiresT145/80D16 is an example of a tiresize.Note: The temporary tire size foryour vehicle may be different fromthis example.1.
Use the recommended cold inflation pressure for optimum tireperformance and wear. Under-inflation or over-inflation may causeuneven treadwear patterns
Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo
• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive (4WD)vehicles (front tires at top of
Note: If your tires show uneven wear ask a qualified technician at aFord or Lincoln/Mercury dealership to check for and correct any wheelmisalignment,
Seating and Safety Restraints 63Seating 63Safety restraints 68Air bags 81Child restraints 91Driving 103Starting 103Brakes 107Traction control 108Trans
AM/FM STEREO WITH IN–DASH 6CD —PREMIUM /AUDIOPHILE(IF EQUIPPED)1./ Tune Selector: Press tomanually increase/decrease theradio frequency when in tuner
If your vehicle has a leak in the exhaust system, a road tire or the sparetire may be exposed to hot exhaust temperatures requiring the tire to berepl
Never spin the tires in excess of the 35 mph (55 km/h) pointindicated on the speedometer.Highway hazardsNo matter how carefully you drive there’s alwa
• Install chains securely, verifying that the chains do not touch anywiring, brake lines or fuel lines.• Drive cautiously. If you hear the chains rub
3For spark plug replacement, see your dealer or a qualified servicetechnician. Refer to the Scheduled Maintenance Guide for theappropriate intervals f
Fluid Ford Part Name Application CapacityTransaxlefluidMotorcraft FullSynthetic ManualTransmission Fluid5-speed manual 2.0L (2.1 quarts)3MotorcraftMER
LUBRICANT SPECIFICATIONSItemFord PartName orEquivalentFord PartNumberFordSpecificationBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFl
ItemFord PartName orEquivalentFord PartNumberFordSpecificationEngine coolant MotorcraftPremium GoldEngine Coolant(yellow-colored)VC-7-A (U.S.,except C
VehicledimensionsSedan - inches(mm)3dr/5dr -inches (mm)Wagon -inches (mm)(5) Track -Front58.9 (1496) 58.9 (1496) 58.9 (1496)(5) Track -Rear58.7 (1492)
• 3dr/5dr2005 Focus (foc)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specifications208
• WagonIDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be a
To activate RDS, press and hold MENU until RDS ON or RDS OFFappears in the display. Press MENU again to continue to FIND andSHOW functions. Press the
Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea
Transmission/Transaxle code designationsYou can find a transmission/transaxle code on the vehicle certificationlabel. The following table tells you wh
Code Transmission DescriptionB Automatic 5–speed overdrive (Torqshift)R Automatic 5–speed overdrive (5R55S)Passenger car application:Code Transmission
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford
Leather wrapped steering wheelsScuff platesSpeed controlLifestyleBike racksCargo organization and managementPeace of mindFirst aid and safety kitsFull
AAir bag supplemental restraintsystem ...81–82, 89and child safety seats ...83description ...
Climate control (see Airconditioning or Heating) ...26–27Clutchfluid ...185–186operation while driving ...113
Fluid capacities ...203Foglamps ...30Fuel ...175calcu
Lane change indicator(see Turn signal) ...32Liftgate ...51Lights, warning and indicator ...
Spare tire(see Changing the Tire) ...134Spark plugs,specifications ...202, 206Specification chart,lubricants ...
5. Seek up: Press for next strongstation or CD track. Press and holdfor continuous seek functionality.6. Text: Press in CD mode todisplay track title,
220
221
222
223
224
16. ON/OFF/Volume: Press to turnON/OFF; turn to increase/decreasethe volume levels. If the volume isset above a certain level and theignition is turne
REMOTE AUDIO STEERING COLUMN CONTROLS (IF EQUIPPED)The remote audio steering column controls may be used to select radioor CD mode. The following func
RADIO RECEPTION FACTORSThere are three factors that can effect radio reception:• Distance/strength: The further you travel from an FM station, theweak
HEATER ONLY SYSTEM(IF EQUIPPED)1. Air flow selections: Controlsthe direction of the airflow in thecabin. See the following for a briefdescription on e
2. Modulate the temperature control to maintain comfort.3. Set the fan speed to the highest setting.4. Direct the outer instrument panel vents toward
5. A/C: Provides cabin cooling.6. Temperature selection: Controls the temperature of the airflow inthe cabin.Max A/C: For maximum cabin cooling perfor
REAR WINDOW DEFROSTERThe rear defroster control is located on the instrument panel.Press the rear defroster control to clear the rear window of thin i
Maintenance and Specifications 162Engine compartment 164Engine oil 165Battery 168Fuel information 175Tire Information 190Part numbers 202Refill capaci
HEADLAMP CONTROLTurns the lamps off.Turns on the parkinglamps, instrument panel lamps,license plate lamps and tail lamps.Turns the headlamps on.Foglam
High beamsPull the lever towards you toactivate. Pull the lever towards youagain to deactivate.Flash to passPull toward you slightly to activateand re
5. Locate the vertical adjuster oneach headlamp. Using a 7mm Allenwrench, turn the adjuster eitherclockwise (to adjust down) orcounterclockwise (to ad
Reading lamps (if equipped)The reading lamps are operated byseparate on/off controls.Theater dimming: The dome lampdims about 20 seconds after thedoor
Replacing headlamp bulbs1. Make sure the headlamp controlis in the OFF position and open thehood.2. Remove the cover panel at thefront of the engine c
Replacing turn signal lamps1. Make sure the headlamp controlis in the OFF position.2. Reach under the bumper coverand remove the bulb socket fromthe t
5. Pull the bulb straight out of the socket.Install in reverse order.Replacing tail/brake/backup lights and turn signal bulbs (wagon)1. Make sure the
Replacing side marker bulbs1. Make sure the headlamp controlis in the OFF position.2. Reach under the front fender,grasp the bulb socket and turn itco
3dr & 5dr and wagon1. Make sure the headlamp controlis in the OFF position.2. Remove the screws using a TorxT20 screwdriver and then removethe pla
Replacing interior lamps1. Make sure the headlamp switch isin the OFF position.2. Switch off the interior lamps(middle switch position).3. Pry out the
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
MULTI-FUNCTION LEVERWindshield wiper: Move the leverdown for a single wipe.For intermittent operation, movecontrol up one position and adjustthe rotar
Changing the wiper blades1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas
HORNPress the steering wheel pad. Thehorn can be operated when theignition is off.OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehicle’s overh
• Place the Velcro hook onto theside of the aftermarkettransmitter opposite of thebutton.• Place the transmitter into storagecompartment, button down.
POWER WINDOWS (IF EQUIPPED)Do not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously inju
MIRRORSPower side view mirrorsTo adjust your mirrors:1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise
Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas
Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RES contro
• Depress the brake pedal until thedesired vehicle speed is reached,press the SET ACCEL control.Turning off speed controlPress the speed control OFFco
• To close the moon roof from the vent position, press and hold the rearportion of the control until the glass panel stops moving.Before operating the
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
and security when appropriately used, particularly in emergencysituations. Safety must be paramount when using mobile communicationsequipment to avoid
WagonPull out the roller cover and securethe retaining points. The cover canbe removed completely by pressinginward on both ends of the support.To red
Do not leave the liftgate open while driving. Doing so could cause seriousdamage to the liftgate and its components as well as allowing carbonmonoxide
KEYSThe key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency.You
1. Turn the ignition to the 3 (ON) position.2. Press the power door unlock control three times.3. Turn the ignition from 3 (ON) position to the 2 (OFF
To open the luggage compartmentdoor (lid) from within the luggagecompartment, pull the illuminated“T” shaped handle and push up onthe trunk lid. The h
Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment.The typ
turned to the 3 (ON) position. The dome lamp control must be set to theON position in order for the illuminated entry feature to operate.Passive locki
Sounding a panic alarmPressto activate the alarm. Press the control again, or turn theignition to the 3 (ON) position to deactivate.Note: The panic al
Replacing lost remote entry transmittersIf you would like to have your remote entry transmitter reprogrammedbecause you lost one, or would like to buy
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
your vehicle or you can program the keys yourself. Refer toProgramming spare keys for instructions on how to program the codedkey.Note: The SecuriLock
Tips:• A maximum of eight keys can be coded to your vehicle.• Only use SecuriLock娂 keys.• You must have two previously programmed coded keys (keys tha
If the key was not successfully programmed, it will not start yourvehicle’s engine and the theft indicator light will flash on and off, or stayon for
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Adjusting the front manual seatPull the lever located under thefront edge of the seat to move theseat forward or backward.Turn the handle to adjust th
• Push control to activate.• Push again to deactivate.The heating will operate when the ignition switch is in position 2.The indicator light on the sw
Do not place objects behind the seat which could prevent theengagement of the seat lock.REAR SEATSFolding rear seat cushion forwardLift the seat cushi
SedanRemove the head restraints (ifequipped) of the rear seats andstow them on the floor behind thefront seats.Pull one or both of the unlockingcontro
SAFETY RESTRAINTSPersonal Safety SystemThe Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupant
common, moderate-severity impacts. A higher energy level is used forthe most severe impacts. Refer to Air bag Supplemental Restraintssection in this c
• how far (if at all) the driver was depressing the accelerator and/or thebrake pedal;• how fast the vehicle was traveling; and• where the driver was
improperly seated or restrained in the front passenger seat contrary toproper child-seating or restraint usage recommendations. Even with thistechnolo
seat position sensor. In addition, the RCM also monitors the restraintswarning light in the instrument cluster. A difficulty with the system isindicat
Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue thatare designed to be used as
The front outboard and rear safety restraints in the vehicle arecombination lap and shoulder belts. The front passenger and rear seatsafety belts have
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
Failure to replace the safety belt assembly under the aboveconditions could result in severe personal injuries in the event ofa collision.Front safety
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war
If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2minutes h
Reasons given... Consider...“Crashes are rare events” 36700 crashes occur every day. Themore we drive, the more we areexposed to “rare” events, even f
Reasons given... Consider...“I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to infla
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle.1. Turn the ignition switch to the RUN (or O
there are no nicks, tears or cuts. Replace if necessary. All safety beltassemblies, including retractors, buckles, front seat belt buckleassemblies, b
Air bags DO NOT inflate slowly or gently, and the risk of injuryfrom a deploying air bag is the greatest close to the trimcovering the air bag module.
Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause thoseobjects to be propelled by the
How does the air bag supplemental restraint system work?The air bag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suff
Several air bag system components get hot after inflation. Do nottouch them after inflation.If the air bag has deployed, the air bag will not function
• the system determines that an infant is present in a rear-facing infantseat that is installed according to the manufacturer’s instructions,• the sys
person isn’t sitting properly in the seat. If this happens, turn the vehicleoff and ask the person to place the seatback in the full upright position,
ObjectsPass Airbag OffIndicator LightPassenger AirbagEmpty seat, Small ormedium object withsafety belt buckledLit DisabledIn case there is a problem w
• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and/or light are repaired.If any of these things ha
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
How does the side air bag system work?The side air bag system consists ofthe following:• An inflatable nylon bag (air bag)with a gas generator conceal
Several air bag system components get hot after inflation. Do nottouch them after inflation.If the side air bag hasdeployed, the air bag willnot funct
Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather, they could burn a small child. Checkseat covers and buckle
Child booster seatsChildren outgrow a typical convertible or toddler seat when they weigh40 pounds (18 kg) and are around 4 years of age. Although the
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
Follow all instructions provided by the manufacturer of thebooster seat.Never put the shoulder belt under a child’s arm or behind theback because it e
• LATCH lower anchors are recommended for use by children up to48 pounds (22 kg) in a child restraint. Top tether anchors can be usedfor children up t
1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly move the seat forwardand back to m
Commentaires sur ces manuels