Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 15Entertainment Systems 18AM/FM stereo 18AM/FM stereo with CD 20AM/FM stereo ca
WARNING LIGHTS AND CHIMESBase instrument clusterBase with Tachometer instrument clusterMid instrument cluster2005 F-150 (f12)Owners Guide (post-2002-f
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Push control to lower head restraint.Front seat• Lift the track release bar to movethe seat forward or rearward.Make sure that the seat isrelatched in
Using the manual lumbar supportFor more lumbar support, turn thelumbar support control toward thefront of vehicle.For less lumbar support, turn thelum
Press the control to move the seatforward, backward, up or down.Memory seats/adjustable pedals (if equipped)This system allows automaticpositioning of
REAR SEATSHead restraintsThe purpose of these head restraints is to help limit head motion in theevent of a rear collision. To properly adjust your he
1. Pull control to release seatcushion.2. Rotate seat cushion up until itlocks into vertical storage position.Returning the seat to seating positionBe
• Restraints Control Module (RCM) with impact and safing sensors.• Restraint system warning light and back-up tone.• The electrical wiring for the air
Front passenger sensing systemFor airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occu
Front outboard safety belt pretensionersThe safety belt pretensioners are designed to tighten the safety beltsfirmly against the occupant’s body durin
Safety restraints precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injur
Luxury instrument clusterWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa
Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.Safety belts and seats can becom
Center front safety belt (Regular Cab center seating position only)Always use both lap and shoulder safety belt in the Regular Cabcenter seating posit
If the belt has been disconnected to carry large objects behind the seat,reconnect it as follows:1. Remove the belt from thestowage clip on the back p
1. To lengthen the lap belt, pullsome webbing out of the shoulderbelt retractor.2. While holding the webbing belowthe tongue, grasp the tip (metalport
Energy management retractorsYour vehicle has a seat belt system equipped with energy managementretractors at the driver and front outboard passenger s
How to use the automatic locking mode1. Buckle the combination lap and shoulder belt.• Right front passenger seat• Rear seats (if equipped)2. Grasp th
How to disengage the automatic locking modeDisconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic l
Failure to replace the safety belt assembly under the aboveconditions could result in severe personal injuries in the event ofa collision.Safety belt
Lap beltsAdjusting the lap beltThe lap belt should fit snugly and as low as possible around thehips, not across the waist.The front center lap belt to
Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occup
On vehicles equipped with a message center, “ENGINE FAILSAFEMODE” will be displayed, refer to Message Center in the DriverControls chapter.Brake syste
If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2minutes h
The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate
To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle.1. Turn the ignition switch to the RUN (or O
Safety belt maintenanceInspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to ma
safety belts in impacts for which the airbags are designed to deploy, andairbags do not offer any protection in crashes for which they do notdeploy.Th
The National Highway Traffic Safety Administration (NHTSA)recommends a minimum distance of at least 10 inches (25 cm)between an occupant’s chest and t
Additional equipment may affect the performance of the airbagsensors increasing the risk of injury. Please refer to the BodyBuilders Layout Book for i
How does the airbag supplemental restraint system work?The airbag SRS is designed toactivate when the vehicle sustainssufficient longitudinal decelera
If the airbag has deployed, the airbag will not function againand must be replaced immediately. If the airbag is notreplaced, the unrepaired area will
Safety belt: Reminds you to fastenyour safety belt. A chime will alsosound to remind you to fasten yoursafety belt.Charging system: Illuminates whenth
The front passenger sensing system is designed to meet the regulatoryrequirements of Federal Motor Vehicle Safety Standard (FMVSS) 208and is designed
If a person of adult-size is sitting in the front passenger’s seat, but the“passenger airbag off” or “pass airbag off” indicator is lit, it could be t
In case there is a problem with thepassenger sensing system, theairbag readiness light in theinstrument cluster will stay lit. DoNOT attempt to repair
Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.Alwa
Booster seats should be used until you can answer YES to ALL of thesequestions:• Can the child sit all the way backagainst the vehicle seat back withk
Both can be used in any vehicle in a seating position equipped withlap/shoulder belts if your child is over 40 lb. (18 kg).The shoulder belt should cr
When installing a child safety seat:• Review and follow the informationpresented in the AirbagSupplemental Restraint Systemsection in this chapter.• U
Installing child safety seats with combination lap and shoulderbeltsAirbags can kill or injure a child in a child seat. NEVER place arear-facing child
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat.
MINI MESSAGE CENTER WARNING DISPLAYS (IF EQUIPPED)Door ajar: Displays when theignition is in the ON position andany door is open.Low fuel: Displays wh
1. Position the child safety seat inthe Regular Cab center front seat.2. If the center lap/shoulder safetybelt has been disconnected from theseat to c
4. While holding both shoulder andlap portions next to the tongue,route the tongue and webbingthrough the child seat according tothe child seat manufa
8. Before placing the child into thechild seat, forcibly pull the childseat forward and back to make surethat the seat is held securely inplace. To ch
7. Before placing the child into the child seat, forcibly tilt the child seatfrom side to side and in forward direction to make sure that the seat ish
• F150 SuperCrew and SuperCabFront seat tether strap attachment1. Position the child safety seat on the seat cushion.2. Route the child safety seat te
• Front seat Regular Cab center(located on back panel)If the tether strap is clippedincorrectly, the child safetyseat may not be retained properlyin t
Rear seat tether strap attachmentThere are three loops of webbingjust above the back of the rear seat(along the bottom edge of the rearwindow) in the
3. Install the child safety seat tightlyusing the LATCH anchors or safetybelts. Follow the instructions in thischapter.4. Tighten the tether strapacco
Never attach two LATCH child safety seats to the same anchor.In a crash, one anchor may not be strong enough to hold twochild safety seat attachments
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary.
• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and
TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen
TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary
INSPECTING AND INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to h
Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙blowout⬙,with unexpected loss of
when you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. Never “bleed” or reduce airpressure when
Important: Remember to replace the spare tire when you replace theroad tires on your vehicle. Even if it has never been used, the spare tireshould be
Use of a temporary emergency spare tire at any one wheel location canlead to impairment of the following:• Handling, stability and braking performance
2. Fully insert the jack handlethrough the bumper hole and intothe guide tube through the accesshole in the rear bumper.3. Turn the handle countercloc
• With Full Message CenterRefer to Message Center in theDrivers Controls chapter on how toswitch the display from Metric toEnglish.Trip odometer: Regi
3. Block the diagonally oppositewheel.4. Obtain the spare tire and jackfrom their storage locations.5. Use the tip of the lug wrench toremove any whee
• RearTo lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engine when yourve
• Seven lug nut wheel12. Stow the flat tire. Refer to Stowing the flat/spare tire.13. Stow the jack and lug wrench. Make sure the jack is fastened so
5. Repeat this tightness check procedure when servicing the spare tirepressure (every six months, as per your scheduled maintenanceinformation), or at
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
7. H: Indicates the tire’s speed rating. The speed rating denotes thespeed at which a tire is designed to be driven for extended periods oftime under
10. Tire Ply Composition and Material Used: Indicates the number ofplies or the number of layers of rubber-coated fabric in the tire tread andsidewall
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
Tire wearMeasure and inspect the tire tread on all your tires periodically.Advanced and unusual tire wear can reduce the ability of tread to gripthe r
Engine oil pressure gauge:Indicates engine oil pressure. Theneedle should stay in the normaloperating range (between “L” and“H”). If the needle falls
Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t
Tire rotationRotating your tires at the recommended interval (as indicated in thescheduled maintenance information that comes with your vehicle) willh
SNOW TIRES AND CHAINSSnow tires must be the same size and grade as the tires youcurrently have on your vehicle.The tires on your vehicle have all weat
Vehicle Curb Weight – is the weight of your new vehicle when youpicked it up from your authorized dealer plus any aftermarketequipment.Payload – is th
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei
GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).
Maximum Loaded Trailer Weight – is the highest possible weight of afully loaded trailer the vehicle can tow. It assumes a vehicle with onlymandatory o
5. Determine the combined weight of luggage and cargo being loaded onthe vehicle. That weight may not safely exceed the available cargo andluggage loa
Special loading instructions for owners of pickup trucks andutility-type vehiclesFor important information regarding safe operation of this typeof veh
FORD AM/FM STEREO SYSTEM (IF EQUIPPED)1./ Tune: Press to manuallygo up or down the radio frequency.Also use in menu mode to selectvarious settings.2.
Regular Cab 4x2 (126” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)4.2L (withmanualtransmission)3.31 7200 (3266)
Regular Cab 4x4 (126” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)4.6L 3.55 11500 (5216) 6200 (2812)4.6L 3.73 12
SuperCab 4x2 (133” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)4.6L 3.55 11500 (5216) 6300 (2858)4.6L 3.73 12000
SuperCab 4x4 (133” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)4.6L 3.55 11500 (5216) 6000 (2722)4.6L 3.73 12000
Crew Cab 4x2 (139” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)4.6L 3.55 11700 (5307) 6300 (2858)4.6L 3.73 12200
Preparing to towUse the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. See your authorized dealer or arel
Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s brake system. Your vehicle may not have enoughbraking power and your chanc
• Allow more distance for stopping with a trailer attached.• The trailer tongue weight should be 10–15% of the loaded trailerweight.• After you have t
• Place the transfer case lever in N (Neutral).• Do not exceed 55 mph (88 km/h) vehicle speed.• The maximum recommended distance is unlimited.• The ve
STARTINGPositions of the ignition1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval.Note: The ignition
Setting the clock: Press until HR or Mn is displayed.Press/ / SEEK to adjust the hours/minutes.3. Seek: Press to access thenext/previous strong statio
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
If starting a vehicle with an automatic transmission:• Make sure the gearshift is in P(Park).• Make sure the parking brake isset.If starting a vehicle
3. Turn the key to 3 (ON) withoutturning the key to 4 (START).2005 F-150 (f12)Owners Guide (post-2002-fmt)USA (fus)Driving192
Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced.• If the driver’s safety
Note: If the engine does not start within five seconds on the first try,turn the key to OFF, wait 10 seconds and try again. If the engine stillfails t
Base instrument cluster withand without tachometerMid and Luxury instrumentclusterFour-wheel anti-lock brake system (ABS)Your vehicle is equipped with
Base instrument cluster withand without tachometerMid and Luxury instrumentclusterParking brakeTo set the parking brake (1), pressthe parking brake pe
STEERINGTo prevent damage to the power steering system:• Never hold the steering wheel at its furthest turning points (until itstops) for more than a
Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.
3. Remove the access plug using a flat head screwdriver, then push theoverride button using a flat head screwdriver, apply the brake pedal andshift th
Locks and Security 85Keys 85Locks 85Anti-theft system 96Seating and Safety Restraints 100Seating 100Safety restraints 105Airbags 124Child restraints 1
FORD SINGLE CD SOUND SYSTEM (IF EQUIPPED)1./ Tune: Press to manuallygo up or down the radio frequency.Also use in menu mode to selectvarious settings.
2. Open the center console bin.Using a screwdriver, carefully pry offthe console finish panel surroundingthe shifter mechanism by inserting ascrewdriv
If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly.See your authorized deal
To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)Always set the parking brake full
• Floor-shift transmissionThe transmission control indicator(TCIL) will illuminate on theinstrument cluster.Drive (not shown)Drive is activated when t
1 (First)• Provides maximum engine braking.• Allows upshifts by moving gearshift lever.• Will not downshift into 1 (First) at high speeds; allows for
4. Move the gearshift lever to 1st gear, then slowly release the clutchpedal while slowly pressing on the accelerator.During each shift, the clutch pe
Maximum downshift speeds1Shift from: Transfer case position (if equipped)2H or 4H 4LD(Overdrive) -455 mph (89 km/h) 21 mph (34 km/h)4 - 3 45 mph (72 k
Removing the keyTurn the ignition off, push therelease lever (located above theignition), then turn the key towardyou and remove the key.REVERSE SENSI
The RSS detects obstacles up to 6feet (2 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the fi
If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement
Fade: Press to adjust the audio between the front and rear speakers.Use/ / SEEK, SEEK .Speed sensitive volume: Radio volume automatically changes slig
N (Neutral) – No power to either front or rear wheels.4L (4WD Low)– Uses extra gearing to provide maximum power to allfour wheels at reduced speeds. I
Do not leave the vehicle unattended with the transfer case in theN (Neutral) position. Always set the parking brake fully and turnoff the ignition whe
3. On vehicles equipped with an automatic transmission, place thetransmission in N (Neutral); on vehicles equipped with a manualtransmission, depress
If your vehicle goes off the edge of the pavement• If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ea
Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,
If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly.See your authorized deal
Mud and waterIf you must drive through highwater, drive slowly. Traction orbrake capability may be limited.When driving through water,determine the de
Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should
Driving on snow and ice4WD vehicles have advantages over 2WD vehicles in snow and ice butcan skid like any other vehicle.Should you start to slide whi
DRIVING THROUGH WATERIf driving through deep or standing water is unavoidable, proceed veryslowly especially when the depth is not known. Never drive
10. Fast forward: Press tomanually advance in a CD track.11. Rewind: Press to manuallyreverse in a CD track.12. Memory presets: To set astation: Selec
• Rear ballast weight behind the rear axle may be required to preventexceeding the FGAWR, and provide front-to-rear weight balance forproper braking a
Never remove or defeat the “tripping mechanisms” designed into thesnow removal equipment by its manufacturer. Doing so may causedamage to the vehicle
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford Motor Companyoffers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call 1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany wil
This switch is located in the frontpassenger’s footwell, behind the kickpanel access cover, to the left of thefuse box. The access cover needs tobe re
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 10A* Run/Accessory - Wipers, Instrumentclu
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description10 20A* Trailer tow back-up lamps relay(PCB1), Trailer tow parklamp relay(R
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description27 5A* Passenger Air bag Deactivation (PAD)warning lamp, Cluster air bag wa
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description103 20A** ABS valves104 — Not used105 30A** Electric trailer brakes106 30A*
FORD DUAL MEDIA SOUND SYSTEM (IF EQUIPPED)1./ Tune: Press to manuallygo up or down the radio frequency.Also use in menu mode to selectvarious settings
Auxiliary relay boxThe relay box is located in the engine compartment on the left fender.• With Daytime Running Lamp (DRL) and 4x4 options• Without Da
JUMP STARTING YOUR VEHICLEThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury
Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
Balance: Press to adjust the audio between the left and right speakers.Use/ / SEEK, SEEK .Fade: Press to adjust the audio between the front and rear s
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai
Board membershipThe Board consists of:• Three consumer representatives• An authorized dealer representativeConsumer candidates for Board membership ar
Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
• Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, sid
• Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all partsthat require cleaning and pressure rinse clean.• Cover the highlighted areas to pr
• 5.4L engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTIC (NON-PAINTED) EXTERIOR
10. Repeat: Press to repeat thecurrent CD track.11. Fast forward: Press tomanually advance in a tape or CDtrack.12. Rewind: Press to manuallyreverse i
• Do not use abrasives, as they may cause scratches.• Do not use fuel, kerosene, or paint thinner to clean any parts.• Wiper blades can be cleaned wit
• If a ring forms on the fabric after spot cleaning, clean the entire areaimmediately (but do not oversaturate) or the ring will set.• Do not use hous
First use a dry cloth then wipe with a damp cloth. Allow the area to dry,then apply conditioner.• Clean spills as quickly as possible.• Test any clean
quality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement the styleand appearance of
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide sc
2. Block the wheels.• Manual transmission:1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral).2. Block the wheels.Note:
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.2L V6 engine1. Battery2. Clutch fluid reservoir (manual transmission)3. Power steering fluid reservo
4.6L V81. Battery2. Transmission fluid dipstick (automatic transmission)3. Engine oil filler cap4. Power steering fluid reservoir5. Engine oil dipstic
5.4L V81. Battery2. Transmission fluid dipstick (automatic transmission)3. Air filter assembly4. Power steering fluid reservoir5. Engine oil dipstick6
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
21. Seek: Press to access theprevious strong station or track.22. Scan: Press for a brief samplingof radio stations or CD tracks. Pressagain to stop.P
4. Open the hood. Protect yourself from engine heat.• 4.2L V6 engine• 4.6L/5.4L V8 engine5. Locate and carefully remove the engine oil level indicator
6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.• If the oil level is between the lower and upper holes or betweenthe MIN
Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t
Change your engine oil and filter according to the appropriate schedulelisted in scheduled maintenance information.Ford production and aftermarket (Mo
Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lightedsubstances to come near th
• If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur
To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. Thecooling system is under press
Coolant refill capacityTo find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in this section.Fill your engine c
3. Menu: Press to toggle throughthe following modes:Autoset: Allows you to set the strongest local radio stations withoutlosing your original manually
How fail-safe cooling worksIf the engine begins to overheat:• The engine coolant temperaturegauge will move to the red (hot)area.• The mini message ce
Never remove the coolant reservoir cap while the engine isrunning or hot.5. Restart the engine and take your vehicle to a service facility.Driving the
Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforerefueling your vehicle.• Al
RefuelingFuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others:• Read and follow all the instr
If the Digital Display reads “CHECKFUEL CAP” and stays on after youstart the engine, the fuel filler capmay not be properly installed. Turnoff the eng
Octane recommendationsYour vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofga
Running out of fuelAvoid running out of fuel because this situation may have an adverseeffect on powertrain components.If you have run out of fuel:• Y
The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fue
Driving style — good driving and fuel economy habitsGive consideration to the lists that follow and you may be able to changea number of variables and
Conditions• Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed.• Carrying unnecessary weight may reduce fuel economy (a
Compression: Available only in CD mode, compression brings soft andloud CD passages together for a more consistent listening level.Repeat: Available o
• Avoid running out of fuel.• Do not turn off the ignition while your vehicle is moving, especially athigh speeds.• Have the items listed in scheduled
government emission standards. The OBD-II system also assists yourauthorized dealer in properly servicing your vehicle. When theindicator illuminates,
POWER STEERING FLUIDCheck the power steering fluid.Refer to the scheduledmaintenance information for theservice interval schedules. If addingfluid is
BRAKE FLUIDThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“
1. Clean the reservoir cap beforeremoval to prevent dirt and waterfrom entering the reservoir.2. Remove cap and rubberdiaphragm from reservoir.3. Add
3. With the parking brake engaged and your foot on the brake pedal,start the engine and move the gearshift lever through all of the gearranges. Allow
High fluid levelFluid levels above the safe rangemay result in transmission failure.An overfill condition of transmissionfluid may cause shift and/ore
Checking and adding manual transmission fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Fluid leve
Transfer case fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough fluid throughthe fil
AIR FILTERRefer to scheduled maintenance information for the appropriateintervals for changing the air filter element.When changing the air filter ele
9. FOLDER: press to access theprevious folder on MP3 discs, iffolders are available.10. Fast forward: Press tomanually advance in a CD track.11. Rewin
• 5.4L Engine1. Release two retainer clamps.2. Pull air filter tray assembly outtoward front of vehicle and lift airfilter element up and out of housi
MOTORCRAFT PART NUMBERSComponent 4.2L V6 engine 4.6L V8 engine 5.4L V8engineAir filter element FA-1632 FA-1632 FA-1754Battery BTX-65-650 BTX-65-650 BT
REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid andclutch fluidMotorcraftHighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to l
Fluid Ford PartNameApplication CapacityPower steeringfluidMotorcraftMERCON威 ATFAll Fill to betweenMIN and MAXlines on reservoirTransfer casefluidMotor
Some transmission fluids may be labeled as dual usage, such asMERCON威 and MERCON威 V. These dual usage fluids are not to be usedin an automatic transmi
LUBRICANT SPECIFICATIONSItemFord partname orequivalentFord partnumberFordspecificationFront axle(4X4)Motorcraft SAE80W-90Premium RearAxle LubricantXY-
ItemFord partname orequivalentFord partnumberFordspecificationHinges, latches,striker plates,fuel filler doorhinge and doorcheck armMotorcraftSilicone
correct type. Refer to your scheduled maintenance information todetermine the correct service interval.Some transmission fluids may be labeled as dual
VEHICLE DIMENSIONSRegular CabVehicledimensionsStyleside 6.5’box - inches(mm)Flareside 6.5’box - inches(mm)Styleside 8.0’box - inches(mm)(1) Overalllen
SuperCabVehicledimensionsStyleside 5.5’box - inches(mm)Styleside /Flareside 6.5’box - inches(mm)Styleside 8.0’box - inches(mm)(1) Overalllength217.8 (
Customer Assistance 237Reporting safety defects (U.S. only) 245Cleaning 246Maintenance and Specifications 254Engine compartment 256Engine oil 259Batte
19. CD eject: Press to eject a CD.Press and hold to auto eject all CDspresent in the system. If there is noCD present, the display will read NO CD.20.
Super CrewVehicle dimensions Styleside 5.5’ box - inches (mm)(1) Overall length 223.8 (5685)(2) Overall width 78.9 (2005)(3) Overall height – 4x2/4x4
Super CrewVehicle dimensions Styleside 5.5’ box - inches (mm)(4) Wheelbase – 4x2/4x4 138.5 (3518) /138.5 (3518)(5) Track - Front 67.0 (1701)(5) Track
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety ComplianceCertification
The Vehicle Identification Number (VIN) contains the following information:1. World manufacturer identifier2. Brake type and Gross VehicleWeight Ratin
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford
Splash guardsStep barsTonneau coversTruck capsWheelsInterior styleElectrochromatic compass/temperature interior mirrorsFloor matsLeather wrapped steer
For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle:• When adding accessories,
AAccessory delay ...61Air cleaner filter ...289, 291Air conditioning ...36, 38Airbag supplemental
Climate control(see Air conditioning orHeating) ...32, 36, 38Clock adjust6-CD in dash ...27AM/FM Ste
Engine block heater ...194Engine oil ...259checking and adding ...259dipstick ...
• Clean the cassette player head with a cassette cleaning cartridge after10–12 hours of play to maintain good sound/operation.Don’t:• Expose tapes to
IIgnition ...189, 297–298Infant seats(see Safety seats) ...135Inspection/maintenance (I/M)testing ...
PParking brake ...196Parts (see Motorcraft parts) ...291Passenger OccupantClassification Sensor ...107Power di
Speed control ...64Starting your vehicle ...189–190,193jump starting ...231Steering wheelcontrol
HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe
To aid in side window defogging/demisting in cold weather:1. Select.2. Adjust the temperature control to maintain comfort.3. Set the fan speed to the
: Distributes air through the windshield defroster vents and floorvents.: Distributes outside air through the windshield defroster vents.3.RRear defro
• For maximum cooling performance (Max A/C):Max A/C mode:• Move the temperature control to the coolest setting.• Set the fan to the highest speed init
AUTOMATIC TEMPERATURE CONTROL (ATC) SYSTEM(IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius: Ifyour vehicle is equipped wi
1. Defrost: Distributes outside air through the windshield defrostervents and demister vents. Can be used to clear the windshield of fog andthin ice.2
Automatic Temperature Control (ATC) system with heated seats(if equipped)Temperature conversion: To switch between Fahrenheit and Celsius:If your vehi
MAX A/C: For maximum cooling performance, press , A/C, ,and set the temperature to 60°F and the highest blower setting.1.Defrost: Distributes outside
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, and certainvehicle components contain or emit chemicals known to t
12. A/C control: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. Engagesautomat
5. Direct the outer instrument panel vents towards the side windows.To increase airflow to the outer instrument panel vents, close the ventslocated in
HEADLAMP CONTROLRotate the headlamp controlclockwise to the first positiontoturn on the parking lamps. Rotateclockwise to the secondpositionto also tu
Foglamp control (if equipped)The headlamp control also operatesthe foglamps. The foglamps can beturned on only when the headlampcontrol is in the, orp
Flash to passPull toward you slightly to activateand release to deactivate.PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and
3. Turn on the low beam headlamps to illuminate the wall or screen andopen the hood. Cover one of the headlamps so no light hits the wall.4. On the wa
INTERIOR LAMPSMap lampsTo turn on the map lamps, press thecontrol next to each lamp.Rear dome lamp (if equipped)The dome lamp lights when thecontrol i
Dome/courtesy lamps (if equipped)The dome lamp lights when:• any door is opened.• the instrument panel dimmerswitch is rotated up until thecourtesy la
Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an
2. At the top and inboard side of theheadlamp, peel the protective coverback from the lower screws andloosen the three retaining screws.3. Once the th
Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti
Replacing front parking lamp/turn signal/sidemarker bulbs1. Make sure the headlamp controlis in the OFF position and open thehood.2. At the top and in
3. Carefully pull the lamp assemblystraight rearward from the tailgatepillar to disengage two hiddensnap-in retainers. (Flare side taillamps are not e
Replacing exterior mounted mirror turn signal indicator lamp bulbsFor bulb replacement, see your authorized dealer.Replacing license plate lamp bulbsT
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
TILT STEERING WHEEL (IF EQUIPPED)Pull the lever down to unlock thesteering column. While the lever isin the down position, tilt thesteering column to
1. To open the bins, move thecenter latch forward which willallow the door to be opened.2. The latches on the side of thebins are to enable the user t
Bin RemovalAttach and remove bins from the rail using the following instructions:Place both palms on the underside of the storage bin, avoiding thesto
While pushing upwards with palms, grip the side latches with fingers andsqueeze.With pressure applied with palms and side latches squeezed down, pulld
Do not plug optional electrical accessories into the cigarette lighter. Usethe power point.Do not use the power point for operating the cigarette ligh
CELL PHONE USEThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri
Service Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This pote
One touch downAllows the driver’s window to openfully without holding the controldown. Press completely down onthe bottom part of the rocker switchand
Accessory delay (if equipped)With accessory delay, the window switches may be used for up to tenminutes after the ignition switch is turned to the OFF
Heated outside mirrors (if equipped)Heated mirrors remove ice, mist andfog. To activate the heated mirrors,press the rear defrost buttonRlocated on th
Fold-away mirrorsFold the side mirrors in carefullybefore driving through a narrowspace, like an automatic car wash.If equipped with powerfold mirrors
The adjustment allows for approximately 3 inches (76 mm) of maximumtravel.Never adjust the accelerator and brake pedal with feet on thepedals while th
Resuming a set speedPress the RES/RESUME control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RES/RESUMEco
• Depress the brake pedal until thedesired vehicle speed is reached,press the SET control.Turning off speed controlThere are two ways to turn off the
In any mode:• Press VOL + or − to adjustvolume.Climate control featuresPress TEMP + or - to adjusttemperature.Press FAN + or - to adjust fanspeed.MOON
To open the moon roof: The moonroof is equipped with a one-touchopen feature. Press and releasethecontrol. The moon roofwill open to the “comfort” pos
Do not use the HomeLink威 Wireless Control System with any garagedoor opener that lacks safety stop and reverse features as required byU.S. federal saf
Front seat mounted rear-facing child or infant seats shouldNEVER be placed in front of an active passenger air bag.Using your vehicle with a snowplowF
3. Simultaneously press and holdboth the HomeLink威 and hand-heldtransmitter button. Do not releasethe buttons until Step 4 hasbeen completed.Some entr
Gate Operator & Canadian ProgrammingDuring programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time for
Erasing HomeLink姞 buttonsTo erase the three programmedbuttons (individual buttons cannotbe erased):• Press and hold the two outerHomeLink威 buttons unt
Selectable featuresResetPress this control to select and resetfunctions shown in the INFO menuand SETUP menu.Info menuThis control displays the follow
Compass zone/calibration adjustment1. Determine your magnetic zone byreferring to the zone map.2. Turn ignition to the ON position.3. Start the engine
10. The compass is now calibrated.Distance to empty (DTE)Selecting this function from theINFO menu estimates approximatelyhow far you can drive with t
2. Record the highway fuel economy for future reference.It is important to press the RESET control after setting the speedcontrol to get accurate high
3. OIL PRESSURE4. BRAKE FLUID LEVEL5. CHARGING SYSTEMUnits (English/Metric)1. Select this function from theSETUP menu for the current unitsto be displ
Language1. Select this function from theSETUP menu for the currentlanguage to be displayed.2. Pressing the RESET controlcycles the message center thro
Warning display StatusDoor ajar Warning can be resetLow fuel level Warning returns after 10 minutesCheck charging systemLow brake fluid levelLow oil p
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
LOW BRAKE FLUID LEVEL. Indicates the brake fluid level is low andthe brake system should be inspected immediately. Refer to Brake fluidreservoir in th
CompassThe compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antennas.Magnetic or metall
Compass calibration adjustmentPerform this adjustment in an open area free from steel structures andhigh voltage lines. For optimum calibration, turn
5. Lift right side off of its hinge.6. Lift tailgate to a 80–degree angle from horizontal.7. Remove tailgate from left side hinge by sliding tailgate
To remove the bed extender:1. Extend the bed extender.2. Pull the round knobs on each sideof the extender to unlock it.Make sure the locking clip scre
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
Childproof door locks (if equipped)• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the ou
Your vehicle is equipped with a remote entry system which allows you to:• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta
The (lock) and (unlock) features will work again after:• a door has become ajar,• the ignition is turned to the 3 (ON) position, or• using the UNLOCKc
Activating the memory featureTo activate this feature:1. Position the seat and adjustable pedals to the positions you desire.2. Press the SET control
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery. Note: Please refer to local r
To program the transmitters yourself:• Unlock all doors using the powerdoor lock/unlock control. Insert akey and turn the ignition fromthe 1 (OFF/LOCK
The dome lamp control (if equipped) must not be set to the off positionfor the illuminated entry system to operate.The inside lights will not turn off
4. Within five seconds, press the control two times. Note: One hornchirp should be heard, indicating the system has been disabled.Conversely, a horn c
Power door unlock/lock procedureYou must complete Steps 1–5 within30 seconds, or the procedure willhave to be repeated. If theprocedure needs to be re
KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to:• lock all vehicle doors.• unlock only the driver’s door.• unlock all vehicle
Antiscan featureThe keyless entry keypad is equipped with an anti-theft function called“antiscan.” The antiscan feature provides a one-minute lockout
Note: The SecuriLock娂 passive anti-theft system is not compatible withnon-Ford aftermarket remote start systems. Use of these systems mayresult in veh
Automatic disarmingSwitching the ignition to the 3 (ON) position with a coded key disarmsthe vehicle.Replacement keysIf your keys are lost or stolen a
3. Within ten seconds of removing the first coded key, insert the secondpreviously programmed coded key into the ignition and turn the ignitionfrom th
Commentaires sur ces manuels