Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 14Entertainment Systems 18AM/FM stereo with CD 18AM/FM stereo with in-dash six
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
To adjust cross-bar position (ifequipped):1. Loosen the thumbwheel at bothends of the cross-bar (bothcross-bars are adjustable).2. Slide the cross-bar
KEYSOne key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency.Your keys are programmed to your v
Childproof door locks• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the
The remote entry system allows youto lock or unlock all vehicle doorsand liftgate and open the liftgatewindow without a key.The remote entry lock/unlo
2. Press and release again within three seconds to confirm that all thedoors are closed and locked. Note: The doors will lock again, the hornwill chir
Deactivating the memory seat featureTo deactivate this feature:1. Press the SET control on the driver’s door panel.2. Within 5 five seconds, press any
Note: Replacement of the battery will not cause the remote transmitterto become deprogrammed from your vehicle. The remote transmittershould operate n
9. Turn the ignition to the 1 (OFF/LOCK) position after you havefinished programming all of the remote entry transmitters.10. The doors will lock, the
When pressing the controls on the keypad, press the middle of thecontrols to ensure a good activation.Programming a personal entry codeTo create your
Unlocking and locking the doors, liftgate and liftgate window usingkeyless entryTo unlock the driver’s door, enter the factory set 5-digit code or you
On board diagnostics (OBD-II) in the Maintenance and Specificationschapter. If the light is blinking, engine misfire is occurring which coulddamage yo
Power door unlock/lock procedureYou must complete steps 1-5 within30 seconds or the procedure willhave to be repeated. If theprocedure needs to be rep
SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEMSecuriLock娂 passive anti-theft system is an engine immobilizationsystem. This system is designed to help prevent
Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 2(ACCESSORY) position.The theft indicator will flash everytwo seco
Please read and understand theentire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition.2. Turn the igniti
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Push control to lower head restraint.Adjusting the front manual seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving
Using the power lumbar support (if equipped)The power lumbar control is located on the outboard side of the seat.Press one side of the control toadjus
Press rear to raise or lower the rearportion of the seat cushion.Press the control to move the seatforward, backward, up or down.Memory seat/adjustabl
The easy entry/exit feature automatically moves the drivers seatbackwards slightly (if room is available) when the key is removed fromthe ignition. It
REAR SEATSFolding down the 60/40 rear seats (if equipped)If the rear seat is equipped with adjustable head restraints, they shouldbe placed in the ful
Air bag readiness: If this light failsto illuminate when ignition is turnedto ON, continues to flash or remainson, have the system servicedimmediately
Adjusting the 2nd row reclineThe 2nd row reclines for additional comfort. To adjust the 2nd rowrecline, pull the handle forward and push the seat back
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped underneath theseatback. After returning the
Folding the middle 2nd row seat (If equipped)To fold the seatback down:1. Locate the lever on the top left ofthe seatback.2. Pull the lever up and pus
To put seat in stowed position:1. Pull the seat release lever locatedon top of the seatback whilepushing the seatback down onto theseat cushion.2. The
2. Pull the seat release lever locatedon top of the seatback while liftingthe seatback into the uprightposition.3. The seatback will latch into place.
How does the personal safety system work?The Personal Safety System can adapt the deployment strategy of yourvehicle’s safety devices according to cra
Front safety belt usage sensorsThe front safety belt usage sensors detect whether or not the driver andfront outboard passenger safety belts are faste
If any of these things happen, even intermittently, have the PersonalSafety System serviced at your dealership or by a qualified technicianimmediately
Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.Safety belts and seats can becom
2. To unfasten, push the release button and remove the tongue from thebuckle.• Front and rear seatsAll safety restraints in the vehicle are combinatio
Door ajar (if equipped):Illuminates when the ignition is inthe ON position and any door isopen.Overdrive off: Illuminates whenthe overdrive function o
How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt
After any vehicle collision, the combination lap and shoulder beltsystem at all passenger seating positions must be checked by aqualified technician t
Safety belt height adjustmentYour vehicle has safety belt heightadjustments for the front andsecond row outboard seatingpositions.Adjust the height of
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate
1. Turn the ignition switch to the RUN (or ON) position. (DO NOTSTART THE ENGINE)2. Wait until the safety belt warning light turns off. (Approximately
a collision be replaced. However, if the collision was minor and aqualified technician finds that the belts do not show damage andcontinue to operate
All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bagsupplemental restraint system (
Children and air bagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rea
Headlamps on warning chime: Sounds when the headlamps or parkinglamps are on, the ignition is off (the key is not in the ignition) and thedriver’s doo
The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burn
• diagnostic module.• and the electrical wiring which connects the components.The diagnostic module monitors its own internal circuits and thesuppleme
Do not lean your head on the door. The Safety Canopy娂 couldinjure you as it deploys from the headliner.Do not attempt to service, repair, or modify th
• Two side crash sensors mounted at the base of the B-pillar (one oneach side of the vehicle).• Two side crash sensors located at the c-pillar behind
If the Safety Canopy娂system has deployed, theSafety Canopy娂 will notfunction again. The SafetyCanopy娂 system (including theA, B and C pillar trim) mus
SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Air bag supplem
Child booster seatsChildren outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the la
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
Follow all instructions provided by the manufacturer of thebooster seat.Never put the shoulder belt under a child’s arm or behind theback because it e
• LATCH lower anchors are recommended for use by children up to 48lb. (22 kg) in a child restraint. Top tether anchors can be used forchildren up to 6
Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,
1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly move the seat forwardand back to m
• 7 passenger vehicleAttach the tether strap only to the appropriate tether anchor asshown. The tether strap may not work properly if attachedsomewher
• At the rear of the cargo area4. Clip the tether strap to theanchor.If the tether strap is clipped incorrectly, the child safety seatmay not be retai
Attaching safety seats with LATCH (Lower Anchors and Tethers forChildren) attachments for child seat anchorsSome child safety seats have two rigid or
The lower anchors for child seatinstallation are located at the rearsection of the second row seatbetween the cushion and seat back.The LATCH anchors
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary.
• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and
• Optional instrument clusterPress and release the TRIP/RESETbutton to toggle between odometerand trip odometer display.Tachometer: Indicates the engi
TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen
TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary
INSPECTING AND INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to h
Use the recommended cold inflation pressure for optimum tireperformance and wear. Under-inflation or over-inflation may causeuneven treadwear patterns
To check the pressure in your tire(s):1. Make sure the tires are cool, meaning they are not hot from drivingeven a mile.Note: If you have to drive a d
Make sure all tires and wheels on the vehicle are of the same size, type,tread design, brand, load-carrying capacity and speed rating because itcan af
The use of tire sealants may damage your tires. The use of tiresealants may also damage your Tire Pressure Monitoring System(if equipped).If your vehi
• All-Wheel driving capability (if applicable)• Load leveling adjustment (if applicable)When driving with the dissimilar spare tire/wheel additional c
Location of the spare tire and toolsThe spare tire and tools for your vehicle are stowed in the followinglocations:Tool LocationSpare tire Under the v
Removing the spare tireDo not use an impact wrench on the winch drive nut. This willdamage the spare tire winch.1. Open the cover from the carpeting o
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe
3. Turn the wrenchcounterclockwise until the tire islowered to the ground and the cablehas slack. When turning the wrench,make sure that it does not s
3. Assemble the jack handleextension on the lug nut wrench bysliding the square end of the jackhandle through the plastic grommeton the lug nut wrench
To lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engine when yourvehicle
increases significantly and the spare tire carrier ratchets or slips whenthe tire is raised to the maximum tightness. Tighten to the best of yourabili
When a wheel is installed, always remove any corrosion, dirt andforeign materials present on the mounting surfaces of the wheel andthe surface of the
5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new tires to match the new wheeldiameter
numbers represent the week and year the tire was built. For example,the numbers 317 mean the 31st week of 1997. After 2000 the numbersgo to four digit
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE CAREImproper or inadequate vehicle maintenance can also cause tires to wearabnormally. Here are some of the important maintenance items:Tire wear
AM/FM STEREO / SINGLE CD RADIO (IF EQUIPPED)1. BAL (Balance): Press/to shift sound to the left/rightspeakers.2. FADE: Press/ to shiftsound to the fron
Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t
The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear.Tire rotationRotating your tire
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can
TIRE PRESSURE MONITORING SYSTEM (TPMS)(IF EQUIPPED)When the Tire Pressure MonitoringSystem warning light is lit, one ormore of your tires is significa
The tire pressure should be checked periodically (at least monthly) usingan accurate tire gauge, refer to Inspecting and inflating your tires inthis c
When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.
When inflating your tiresWhen putting air into your tires (such as at a gas station or in yourgarage), the Tire Pressure Monitoring System may not res
The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RS-210 of Industry Canada. Operation is subject to thefollowing two
VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
5. EJ (Eject): Press to eject a CD.6. COMP (Compression): In CDmode, press to bring louder andsofter levels into more comfortablelistening level. The
GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei
GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).
mandatory options, no cargo (internal or external), a tongue load of10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), a
6. If your vehicle will be towing a trailer, load from your trailer will betransferred to your vehicle. Consult this manual to determine how thisreduc
Special loading instructions for owners of pickup trucks andutility-type vehiclesFor important information regarding safe operation of this typeof veh
• Refer to the instructions included with towing accessories for theproper installation and adjustment specifications.Do not exceed the maximum loads
4x4/AWDGCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axleratioMaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.0L SOHC Cla
Safety chainsAlways connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cr
• Under extreme conditions with large frontal trailers, high outsidetemperatures and highway speeds, the coolant gauge may indicatehigher than normal
• do not allow waves to break higher than 6 inches (15 cm) above thebottom edge of the rear bumper.Exceeding these limits may allow water to enter veh
Seating and Safety Restraints 114Seating 114Safety restraints 124Air bags 137Child restraints 145Tires, Wheels and Loading 157Tire Information 161Tire
15. AM/FM: Press to choose afrequency band in radio mode.16. BASS: Press/ toincrease/decrease the bass output.17. TREB (Treble): Press/to increase/dec
STARTINGPositions of the ignition1. OFF/LOCK, shuts off the engineand all accessories/locks the steeringwheel, gearshift lever and allows keyremoval.2
• Make sure the gearshift is in P(Park).3. Turn the key to 3 (ON) withoutturning the key to 4 (START).Make sure the corresponding lights illuminate or
Starting the engine1. Turn the key to 3 (ON) withoutturning the key to 4 (START). Ifthere is difficulty in turning the key,rotate the steering wheel u
If the engine fails to start using the preceding instructions (flexiblefuel vehicles only)1. Press and hold down the accelerator 1/3 to 1/2 way to flo
Refer to Brake system warninglight in the Instrument Clusterchapter for information on the brakesystem warning light.Four-wheel anti-lock brake system
Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th
Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.ADVANCETR
Driving conditions which may activate AdvanceTrac威 include:• Taking a turn too fast.• Maneuvering quickly to avoid an accident, pedestrian or obstacle
warning indicator light in the instrument cluster remains on while theengine is running, have the system serviced immediately.Pressing the control onc
STEERINGTo prevent damage to the power steering system:• Never hold the steering wheel at its furthest turning points (until itstops) for more than a
AUDIOPHILE SATELLITE COMPATIBLE AM/FM STEREO IN-DASHSIX CD RADIO (IF EQUIPPED)1. Seek: Press and releaseSEEK/ for previous/nextstrong station or track
Loaded vehicles, with a higher center of gravity, may handledifferently than unloaded vehicles. Extra precautions such asslower speeds and increased s
3. Remove the access plug with aflat head screwdriver (or similartool).4. Insert a tool (or screwdriver) into the access hole to override thebrake-shi
Driving with a 5–speed automatic transmissionThis vehicle is equipped with an adaptive Transmission Shift Strategy.Adaptive Shift Strategy offers the
D (Drive) with OverdriveThe normal driving position for thebest fuel economy. Transmissionoperates in gears one through five.D (Drive) without Overdri
Forced downshifts• Allowed in D (Overdrive) or Drive.• Depress the accelerator to the floor.• Allows transmission to select an appropriate gear.If you
Certain add-on devices such as large trailer hitches, bike orsurfboard racks and any device that may block the normaldetection zone of the RSS system
If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement
Using the Control Trac 4WD system4X4 AUTO - Power to all four wheels; used for normal street andhighway driving.4X4 HIGH (4WD High) - Used for extra t
4. Press the desired 4WD position.• If shifting into 4X4 LOW (4WD Low), wait for the 4X4 LOW light inthe instrument cluster to turn on indicating the
If your vehicle goes off the edge of the pavement• If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ea
3. DSP (Digital SignalProcessing): Press DSP to accessthe Ambiance menu. Ambiance givesthe feeling of “being there” to yourmusic, creating increased c
turn the steering wheel only as rapidly and as far as required to avoidthe emergency. Excessive steering will result in less vehicle control,not more.
4WD Systems4WD uses all four wheels to power the vehicle. This increases traction,enabling you to drive over terrain and road conditions that aconvent
Mud and waterIf you must drive through highwater, drive slowly. Traction orbrake capability may be limited.When driving through water,determine the de
possibly rolling over. Whenever driving on a hill, determine beforehandthe route you will use. Do not drive over the crest of a hill withoutseeing wha
Avoid sudden applications of power and quick changes of direction onsnow and ice. Apply the accelerator slowly and steadily when startingfrom a full s
ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED)Your vehicle may be equipped with a full-time All Wheel Drive (AWD)transfer case. With the AWD option, power
Basic operating principles• Drive slower in strong crosswinds which can affect the normal steeringcharacteristics of your vehicle.• Be extremely caref
Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position andremove the key wheneve
AWD Systems (if equipped)AWD uses all four wheels to powerthe vehicle. This increases traction,enabling you to drive over terrainand road conditions t
when you are driving over sand, apply the accelerator slowly and avoidspinning your wheels. If the vehicle does slide, steer in the direction ofthe sl
9. Menu: Press MENU to accessclock mode, RDS on/off, Trafficannouncement mode, Program typemode, Shuffle and Compressionmode.The Federal Communication
Apply just enough power to the wheels to climb the hill. Too muchpower will cause the tires to slip, spin or lose traction, resulting in loss ofvehicl
brake steadily. Do not “pump” the brakes. Refer to the Brakes section ofthis chapter for additional information on the operation of the anti-lockbrake
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
The fuel pump shut-off switch islocated in the passenger’s foot well,by the kick panel.Use the following procedure to reset the fuel pump shut-off swi
Standard fuse amperage rating and colorCOLORFuseratingMini fusesStandardfusesMaxi fusesCartridgemaxi fuses2A Grey Grey ——3A Violet Violet ——4A Pink Pi
The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 30A Memory seat module, Driver powerseat,
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description12 5A 4x4 (switch)13 5A Overdrive cancel switch14 5A PATS15 5A Rear wiper m
Passenger compartment fuse panel (top side)These relays are located on the reverse side of the passengercompartment fuse panel. See your dealer or a c
Power distribution boxThe power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protec
11. SAT (if equipped): YourAudiophile radio comes equippedwith Satellite Ready capability. Thekit to enable the Satellite reception is available throu
The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 60A** PJB #12 30A** BSM3 — Not used4 30
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription15 15A* Memory (PCM/DEATC/Cluster),Courtesy lamps16 15A* Park lamps, Autolamp parklam
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription42 10A* Right low beam43 10A* Left low beam44 15A* Front foglamps45 2A* Brake pressur
Rear relay boxThe relay box is located on the rear passenger side quarter trim panel.See your dealer or a certified technician for service of this rel
Auxiliary relay box (Vehicles equipped with 4x4)The relay box is located on the frontright fender well.The relays are coded as follows:Fuse/Relay Loca
Preparing your vehicleWhen the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, th
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery.After the disabled vehicle has been started and the jumper
label may peel and cause the CD to become jammed. It isrecommended that homemade CDs be identified with permanentfelt tip marker rather than adhesive
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai
Board membershipThe Board consists of:• Three consumer representatives• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa
Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)In those cases where you continue to feel that the efforts by Ford ofCanada and the dealer to
If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED)1. Power/volume: Press to turnON/OFF; turn to increase/decreasevolume.2. SCAN: Press to hear a br
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
• Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, sid
• Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all partsthat require cleaning and pressure rinse clean.• Cover the highlighted areas to pr
PLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your dealer.• For routine clea
INTERIOR TRIM• Clean the interior trim areas with a damp cloth, then with a clean, drycloth.• Do not use household or glass cleaners as these may dama
FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury dealer has many quality products availableto clean your vehicle and protect its
SERVICE RECOMMENDATIONS• Use the scheduled maintenance information to track routineservice.• Use only recommended fuels, lubricants, fluids and servic
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.0L SOHC V6 engine1. Engine coolant reservoir2. Engine oil filler cap3. Power steering fluid reservoi
4.6L V8 engine1. Engine coolant reservoir2. Engine oil dipstick3. Brake fluid reservoir4. Power distribution box5. Battery6. Power steering fluid rese
not be inserted into the CD player. The label may peel and causethe CD to become jammed. It is recommended that homemadeCDs be identified with permane
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
ENGINE OILChecking the engine oilRefer to the scheduled maintenance information for the appropriateintervals for checking the engine oil.1. Make sure
• 4.6L V8 engine6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.• If the oil level is between the MIN and MAX marks, the
• 4.6L V8 engine• Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician.7. Put the in
Engine Oil Recommendations4.6L EngineLook for this certificationtrademark.Use SAE 5W-20 engine oil.Only use oils “Certified For Gasoline Engines” by t
4.0L EngineLook for this certificationtrademark.Use SAE 5W-30 engine oil.Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Insti
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How
When lifting a plastic-cased battery, excessive pressure on the endwalls could cause acid to flow through the vent caps, resulting inpersonal injury a
If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreco
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
to decrease minutes or TUNE to increase minutes. If your vehiclehas a stand alone clock this control will not function.10. BAL (Balance): Press BAL;th
Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur
remove the coolant pressure relief cap on the radiator of a vehicle withan overflow system, follow these steps to add engine coolant.To reduce the ris
Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut
What you should know about fail-safe cooling (4.6L V8 engineonly)If the engine coolant supply is depleted, this feature allows the vehicle tobe driven
Never remove the coolant reservoir cap while the engine isrunning or hot.5. Restart the engine and take your vehicle to a service facility.Driving the
Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforefueling your vehicle.• Alwa
amount of gasoline is added to make it unfit for beverage use. Theresulting ethanol blend is called denatured fuel ethanol meaning that it isdenatured
Choosing the right fuelIf your vehicle is a flexible fuel vehicle (FFV), use only UNLEADEDFUEL and FUEL ETHANOL (Ed75–Ed85)Your vehicle was not design
Fuel qualityMany of the world’s automakers approved the World-wide Fuel Charterthat recommends gasoline specifications to provide improvedperformance
Running out of fuelAvoid running out of fuel because this situation may have an adverseaffect on powertrain components.If you have run out of fuel:• Y
15. SIDE 1–2: Works in tape modeonly. Press to play reverse side ofthe tape.16. FF (Fast Forward): In CDmode, press for a slow advance,press and hold
Fuel FilterFor fuel filter replacement, see your dealer or a qualified servicetechnician. Refer to scheduled maintenance information for theappropriat
• Allow no more than two automatic click-offs when filling.• Always use fuel with the recommended octane rating.• Use a known quality gasoline, prefer
Driving style — good driving and fuel economy habitsGive consideration to the lists that follow and you may be able to changea number of variables and
• Carrying unnecessary weight may reduce fuel economy (approximately1 mpg [0.4 km/L] is lost for every 400 lb [180 kg] of weight carried).• Adding cer
• Do not turn off the ignition while your vehicle is moving, especially athigh speeds.• Have the items listed in scheduled maintenance informationperf
service technician in properly servicing your vehicle. When the Checkengine/Service engine soon light illuminates, the OBD-II system hasdetected a mal
CHECKING AND ADDING POWER STEERING FLUIDCheck the power steering fluid. Refer to the scheduled maintenanceguide for the service interval schedules. If
BRAKE FLUID RESERVOIRThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels below the “M
CHANGING THE AIR FILTER ELEMENT1. Release the clamps that secure the air filter housing cover.2. Carefully separate the two halves of the air filter h
3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening.Use only fluid that meets Ford specifications
Cleaning 260Maintenance and Specifications 266Engine compartment 268Engine oil 271Battery 276Engine Coolant 278Fuel information 284Air filter(s) 298Pa
21. SEEK: Press and releaseSEEK/ for previous/nextstrong station, selection or track.22. AM/FM: Press to selectAM/FM1/FM2 frequency band.SATELLITE COM
2For spark plug replacement, see your dealer or a qualified servicetechnician. Refer toscheduled maintenance information for theappropriate intervals
Fluid Ford PartNameApplication CapacityTransmissionfluid1MotorcraftMERCON威 VATFAutomatictransmissions12.7 quarts(12.0L)2Transfer case MotorcraftMERCON
2Indicates only approximate dry-fill capacity. Some applications may varybased on cooler size and if equipped with an in-tank cooler. The amountof tra
ItemFord PartName orequivalentFord PartNumberFordSpecificationEngine coolant MotorcraftPremium GoldEngine Coolant(yellow-colored)VC-7-A (U.S.,except C
ItemFord PartName orequivalentFord PartNumberFordSpecificationTransfer case(4X4)MotorcraftMERCON威Multi-PurposeATFXT-2-QDX MERCON威Transfer caseFront Ou
VEHICLE DIMENSIONSDimensions 4-Door 4x2 or 4x4 XLT Model -Inches (mm)(1) Overall length 191.6 (4866.7)(2) Overall width 73.7 (1870.9)(2) Overall width
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
Vehicle identification numberThe vehicle identification number(VIN) is a 17 digit combination ofletters and numbers. The VIN isattached to a metal tag
Transmission/Transaxle code designationsYou can find a transmission/transaxle code on the vehicle certificationlabel. The following table tells you wh
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for your vehiclethrough your local authorized Ford
seconds of the previous press to proceed to the next/last text display.The last text field shown on the display will become the new displaymessage def
Interior styleElectrochromatic compass/temperature interior mirrorsFloor matsLeather wrapped steering wheelsScuff platesLifestyleBike racksCargo organ
• To avoid interference with other vehicle functions, such as anti-lockbraking systems, amateur radio users who install radios and antennasonto their
AAccessory delay ...71AdvanceTrac ...206Air bag supplemental restraintsystem ...
waxing ...260wheels ...261wiper blades ...263Climate con
lubrication specifications ...302,304refill capacities ...300service points ...268–269starting after a collisio
Heatingheating and air conditioningsystem ...47, 49Homelink wireless controlsystem ...
PParking brake ...205Parts (see Motorcraft parts) ...299Pedals (see Power adjustablefoot pedals) ...
tilting ...65TTilt steering wheel ...65Tire Pressure MonitoringSystem (TPMS)Driving ...
318
319
Autoset: Press MENU until AUTOSET appears in the display. Press SELto toggle ON/OFF. Allows you to set the strongest local radio stationswithout losin
320
15. REW(Rewind): In CD/MP3mode, press until desired selectionis reached.16. SAT (if equipped): Your radiocomes equipped with Satellite Readycapability
21. COMP(Compression): Bringssoft and loud CD passages togetherfor a more consistent listening levelwhen in CD mode. Press COMP to turn the feature ON
PREMIUM SATELLITE COMPATIBLE AM/FMSTEREO/CASSETTE/SINGLE CD/MP3 — LATE AVAILABILITY(IF EQUIPPED)1. CD slot: Insert a CD with thelabel side up.CD units
2. CD Eject: Press to eject a CD.The radio will resume playing.3. Mute: Press to MUTE playingmedia; press again to return to theplaying media.4. Tape
Dolby: In tape mode, press MENU until DOLBY B XX appears in thedisplay. Press SEL to toggle ON/OFF.The Dolby威 noise reduction system is manufactured u
11. TEXT/SEL: The filename, songtitle, artist or album text may beviewed while playing an MP3selection. Press TEXT to scroll through the text fields.
17. Memory preset buttons: To set a station: Press BAND to select thefrequency band (AM/FM1/FM2), tune to a station, press and hold apreset button unt
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, and certainvehicle components contain or emit chemicals known to t
AUDIOPHILE SATELLITE COMPATIBLE AM/FM STEREO IN-DASHSIX CD/MP3 RADIO — LATE AVAILABILITY (IF EQUIPPED)1. SEEK: Press and releaseSEEK/ for previous/nex
3. AUX: This function is notoperational.4. MUTE: Press to MUTE playingmedia; press again to return toplaying media5. EJ: Press to eject a CD. Press EJ
Traffic: Allows you to hear traffic broadcasts. With the feature ON, pressSEEK or SCAN to find a station broadcasting a traffic report (if it isbroadc
Folder/Track Mode: In MP3 mode, press MENU until MODE appears inthe display. Use SEL to toggle between FOLDER (only tracks withinselected folder are a
19. Power/volume: Press to turnON/OFF; turn to increase ordecrease volume levels.20. Load: Press to load a CD. PressLOAD and a memory preset to loadto
FAMILY ENTERTAINMENT SYSTEM (IF EQUIPPED)Your vehicle may be equipped with a Family Entertainment System(FES). Refer to the DVD Supplement Guide for f
CD/CD PLAYER CAREDo:• Handle discs by their edges only. Never touch the playing surface.• Inspect discs before playing. Clean only with an approved CD
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
• To improve the A/C cool down, drive with the windows slightly openfor 2–3 minutes after start up or until the vehicle has been “aired out.”For maxim
Dual Automatic Temperature Control (DATC) system (if equipped)1. A/C control: Uses outside air tocool the vehicle. Press to turn on/offin all modes ex
Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti
6. : Distributes outside air through the windshield defroster vents.7.: Distributes outside air through the windshield defroster ventsand floor vents.
Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
Auxiliary system (if equipped)Your vehicle may be equipped with auxiliary climate controls. Theseallow the front or rear seat passengers to control ai
Rear auxiliary controls (if equipped):Once the front auxiliary control is set to REAR, the rear seat passengersmay use the rear auxiliary controls in
REAR WINDOW DEFROSTERThe rear defroster control is locatedon the instrument panel.Press the rear defroster control toclear the rear window of thin ice
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola
Daytime running lamps (DRL) (if equipped)To activate DRL:• the ignition must be in the ON position and• the headlamp control is in theor position• the
Use to adjust the brightness of theinstrument panel when exteriorlights are on.• Rotate up to brighten.• Rotate down to dim.• Rotate to full up positi
3. Turn on the low beam headlamps.The brightest part of the lightshould be below the horizontal line(4). If it is above the line theheadlamp will need
INTERIOR LAMPSDome/reading lampsThe dome lamp lights when:• any door is opened.• the instrument panel dimmerswitch is rotated up until thecourtesy lam
Please read the section Supplemental restraint system (SRS)in the Seating and Safety Restraints chapter. Failure to followthe specific warnings and in
Replacing the interior bulbsCheck the operation of the bulbs frequently. To replace any of theinterior bulbs, see a dealer or qualified technician.Usi
Replacing headlamp bulbsDo not touch the glass of a halogen bulb.1. Turn off the headlamps and openthe hood.2. Pry up the two retainer pins untilthey
Replacing front parking lamp/turn signal/sidemarker bulbs1. Turn off the headlamp switch tooff.2. Remove headlamp screw from thebulb assembly.3. Disen
Replacing foglamp bulbs1. Make sure the headlamp switch isin the OFF position.2. Remove the plastic splash shieldby removing the two screws on thefron
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
Changing the wiper blades1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas
Lift the lever back to its originalposition to lock the steering column.Never adjust the steeringcolumn when the vehicle ismoving.CENTER CONSOLEYour v
Mobile Communication Equipment includes, but is not limited to cellularphones, pagers, portable email devices, in-vehicle communicationssystems, telem
Storage compartmentPress the latch to open the storagecompartment.Installing a garage door opener (if equipped)The storage compartment can be converte
Illuminated visor mirror (if equipped)Lift the mirror cover to turn on the visor mirror lamps.Type AType BSlide on rod featureRotate the visor towards
Notice to owners of pickup trucks and utility type vehiclesUtility vehicles have a significantly higher rollover rate thanother types of vehicles.Befo
Do not plug electrical accessories into the cigarette lighter socket(if equipped). Always use the power point for accessories.Do not use the power poi
One touch downAllows the driver’s window to openfully without holding the controldown. Press completely down onAUTO and release quickly. Pressagain to
Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re
POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is
3. Press the SET + control andrelease it.4. Take your foot off the acceleratorpedal.5. The indicator lighton theinstrument cluster will turn on.Note:•
Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET + controluntil you get to the desiredspeed,
Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal. This will not erase your vehicle’s previouslyset
In AM, FM1, or FM2 mode:• Press MEM to select presetstations within the selected radioband.In Tape mode:• Press MEM to select the nextselection on the
Press + or - to adjust fan speed.MOON ROOF (IF EQUIPPED)You can move the glass panel of the moon roof back to open or tilt up toventilate the vehicle.
To vent:To tilt the moon roof into the vent position (when the glass panel isclosed), press and hold the front portion of the control. To close themoo
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
ProgrammingDo not program HomeLink威 with the vehicle parked in the garage.Note: Some vehicles may require the ignition switch to be turned to thesecon
Note: If the indicator light blinks rapidly for two seconds and then turnsto a continuous light, proceed with Steps 6 through 8 to completeprogramming
Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet
ELECTRONIC COMPASS/TEMPERATURE DISPLAY (IF EQUIPPED)Outside air temperatureThe outside temperature display iscontained in the instrument clusterand di
Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the ON p
3. Press the button on the top ofthe compass module until ZONEappears in the instrument clusterdisplay. Continue to hold down untilZONE disappears and
Info menuThis control displays the followingcontrol displays:• Odometer/Compass• Trip odometer/Odometer/Compass• Average Fuel Economy• Trip Elapsed Dr
3. Determine your magnetic zone byreferring to the zone map.4. From Info menu, select theCompass/Odometer function. (Donot select Trip, DTE, or AFE. T
Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in miles/U.S. gallon orliters/100 km.If you calcu
Distance to empty (DTE)Selecting this function from theINFO menu estimates approximatelyhow far you can drive with the fuelremaining in your tank unde
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
Autolocks1. Select this function from theSETUP control for the currentdisplay mode.2. Press the RESET control to turnthe autolocks ON or OFF.Easy entr
2. Pressing the RESET controlcycles the message center througheach of the language choices.3. Press and hold the RESETcontrol to set the language choi
System warningsSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems.In the event of a multiple warning si
Warning display StatusCheck tire pressure (ifequipped)Warning returns after the ignition keyis turned from OFF to ON.Tire pressure monitor fault (ifeq
CHECK CHARGING SYSTEM. Displayed when the electrical system isnot maintaining proper voltage. If you are operating electrical accessorieswhen the engi
CHECK ADVANCETRAC威 (if equipped). Displayed when theAdvanceTrac威 with RSC system is not operating properly. If this messageis displayed on the message
After you have done steps 1 through 3, you can reset the oilmonitoring system to your personalized oil life %:4. Press RESET and SETUPcontrols at the
POSITIVE RETENTION FLOOR MATPosition the driver floor mat so thatthe eyelet is over the pointed end ofthe retention post and rotateforward to lock in.
Always close liftgate window before opening liftgate. Liftgateglass and liftgate should never be open at the same time. Failureto observe this warning
Cargo management systemThe cargo management system consists of storage compartments locatedin the floor of the rear cargo area.7 passenger stowage:1.
Commentaires sur ces manuels