Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 15Entertainment Systems 18AM/FM stereo cassette with CD 18AM/FM stereo with in-
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
AUXILIARY A/C-HEATER CONTROLS (IF EQUIPPED)Your vehicle may be equipped with auxiliary climate controls. Theseallow the front or rear seat passengers
Rear auxiliary controls (if equipped):Once the front auxiliary control is set to REAR, the rear seat passengersmay use the rear auxiliary controls in
HEADLAMP CONTROLRotate the headlamp control to thefirst positionto turn on theparking lamps. Rotate to the secondpositionto turn on theheadlamps.Fogla
Daytime running lamps (DRL) (if equipped)Turns the foglamps on at full intensity output. To activate:• the ignition must be in the ON position and• th
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parklamp operatio
5. Locate the vertical adjuster oneach headlamp, then use a 10 mmsocket/wrench to turn the adjustereither counterclockwise (to adjustdown) or clockwis
Front row map/dome lamp (if equipped)The dome lamp lights when:• any door is opened,• the instrument panel dimmerswitch is rotated up until thecourtes
BULB REPLACEMENTHeadlamp CondensationThe headlamps are vented to equalize pressure. When moist air entersthe headlamp(s) through the vents, there is a
Function Number of bulbs Trade numberHigh-mount brake lamp 5 W5WAll replacement bulbs are clear in color except where noted.To replace all instrument
6. Pull off the bulb covers.7. Once the bulb covers areremoved, the bulbs can be removedby turning them counterclockwiseand then pulling the bulbs str
damage your catalytic converter. Drive in a moderate fashion (avoidheavy acceleration and deceleration) and have your vehicle servicedimmediately.Unde
3. Remove the two headlampassembly retainer bolts and lampassembly from the vehicle.4. Loosen the vertical bolt on thebackside of the headlamp assembl
6. Install the bulb socket into the lamp assembly and rotate clockwise.7. Carefully install the tail lamp assembly on the vehicle by securing thelamp
2. Pull the lamp assembly straightout.3. Remove the wire harness.4. Depress the four tabs that holdthe light assembly on, one at a time,and pull the b
Approach lamp/mirror turn signal bulb removal (if equipped)To change the bulbs:1. Make sure the headlamp switch isin the OFF position and then foldthe
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
Changing the wiper bladesIt is recommended that wiper blades are renewed before winter.To replace the wiper blades:1. Fold back the wiper arm andposit
TILT STEERINGPush the lever down to unlock thesteering column. While the lever isin the down position, tilt thesteering column to the desiredposition.
Slide on rod feature (ifequipped)Rotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage.Note: To stow the viso
To open the moon roof: The moonroof is equipped with a one-touchopen feature. Press and releasethecontrol. The moon roofwill open to the “comfort” pos
Power quarter rear windows (if equipped)• Without a moon roof• With a moon roofPress theportion of the VENT control to open the power rearquarter wind
serviced immediately. Normal braking is still functional unless the brakewarning light also is illuminated.Air bag readiness: If this light failsto il
Do not use the power point foroperating the cigarette lighterelement (if equipped).To prevent the fuse from beingblown, do not use the powerpoint(s) o
Not equipped with rear climatecontrolCigar/Cigarette lighter (if equipped)Do not plug optional electrical accessories into the cigarette lightersocket
One touch downAllows the driver’s window to openfully without holding the controldown. Press completely down onthe bottom part of the rocker switchand
Power side view mirrorsThe ignition can be in any position to adjust the power side view mirrors.To adjust your mirrors:1. Rotate the control clockwis
Powerfold mirrors (if equipped)Rotate the 4–way adjustment switchto the center position. Press theswitch down to auto fold in anddown again to auto fo
Do not use the speed control in heavy traffic or on roads thatare winding, slippery or unpaved.Setting speed controlThe controls for using your speedc
Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RES contro
• Depress the brake pedal until thedesired vehicle speed is reached,press the SET + control.Turning off speed controlThere are two ways to turn off th
STEERING WHEEL CONTROLS (IF EQUIPPED)These controls allow you to operate some radio and climate controlfeatures.Audio control featuresPressto select:•
Climate control featuresPress TMP + or - to adjusttemperature.Press+ or - to adjust fan speed.HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED)The HomeL
Check fuel cap (if equipped):Illuminates when the fuel cap maynot be properly installed. Continueddriving with this light on may causethe Service engi
Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink威 equipped vehiclepurchase). I
5. Press and hold the just-trained HomeLink威 button and observe theindicator light. If the light is constant, programming is complete and yourdevice s
• Continue to press and hold the HomeLink威 button (note Step 3 in the“Programming” section) while you press and release — every twoseconds (“cycle”) y
2. The indicator light will begin to flash after 20 seconds. Withoutreleasing the HomeLink威 button, follow Step 2 in the “Programming”section.For ques
Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the ON p
4. Drive the vehicle slowly (less than 3 mph [5 km/h]) in circles untilCAL indicator turns off. As many as 5 complete circles may be required.5. The c
Compass displayThe compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antenna. Magneticor
7. To exit the zone setting mode,and to “lock in” your change, pressand release the RESET control.Perform compass calibration in an open area free fro
Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in miles/gallon or liters/100km.If you calculate
display to compass display, hold the INFO button again for 2 secondsuntil the compass heading is seen in the displayTo turn the display off or change
Four wheel drive high (ifequipped): Illuminates whenfour-wheel drive is engaged. If thelight fails to illuminate when theignition is turned ON, contin
1. To disable/enable the autolampdelay feature, select this functionfrom the SETUP control for thecurrent display mode.2. Press the RESET control to s
System checkSelecting this function from theSETUP menu causes the messagecenter to cycle through each of thesystems being monitored. For eachof the mo
• They will reappear on the display ten minutes from the reset.• They will not reappear until an ignition OFF-ON cycle has beencompleted.This acts as
Warning display StatusDoor ajar Will not clear until condition iscorrectedReduced engine powerStop engine safelyCheck electronic throttlecontrol or en
LOW TIRE PRESSURE (if equipped).Displayed when one or moretires on your vehicle have low tire pressure. Refer to Inspecting andInflating Your Tires in
CHECK ADVTRAC (if equipped). Displayed when the AdvanceTrac威with RSC system is not operating properly. If this message is displayedon the message cent
• Engine sensorContact your dealer as soon as possible if these messages occur on aregular basis.CENTER CONSOLE (IF EQUIPPED)The center console offers
POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)Position the floor mat so that theeyelet is over the pointed end of theretention post and rotate forward tol
LUGGAGE RACKYour vehicle is equipped with a roofrack. The maximum recommendedload is 200 lbs (90 kg), evenlydistributed. If it is not possible todistr
KEYSOne key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency.Your keys are programmed to your v
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
Childproof door locksWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo
Unlocking the doors/liftgatePress this control to unlock thedriver’s door. The interior lamps willilluminate with the ignition is in the1 (OFF/LOCK) p
Sounding a panic alarmPress this control to activate thealarm.The personal panic alarm will cyclethe horn and parking lamps on/off.To deactivate the a
Deactivating the memory seat featureTo deactivate this feature:1. Press the SET control on the driver’s door panel.2. Within 5 five seconds, press any
Note: Replacement of the battery will not cause the remote transmitterto become deprogrammed from your vehicle. The remote transmittershould operate n
Illuminated entryThe lamps illuminate when the remote entry system is used to unlockthe door(s).The system automatically turns off after 25 seconds or
• release the liftgate glass,• enable or disable the autolock function, and• add or delete a 5–digit personal user code.Your vehicle has a factory set
2. Press the 1 • 2 control within five seconds of Step 1.3. Enter your personal 5–digit code.Enter each digit within five secondsof previous one.4. Af
Activating/deactivating autolock with the keyless entry system1. Turn the ignition to the 1 (OFF/LOCK) position.2. Close all the doors, the liftgate a
Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 1(OFF/LOCK) position.Automatic disarmingSwitching the ignition to
• With Full Message CenterRefer to Message Center in theDriver Controls chapter on how toswitch the display from Metric toEnglish.Trip odometer: Regis
If your keys are lost or stolen you will need to do the following:• Use your spare key to start the vehicle, or• Have your vehicle towed to a dealersh
4. Turn the ignition from the 3 (ON) back to 1 (OFF/LOCK) position inorder to remove the second coded key from the ignition.5. Within 10 seconds of re
SEATINGFront row adjustable head restraints (if equipped)Your vehicle’s seats are equipped with two-way adjustable headrestraints. The purpose of thes
Lift handle to move seat forward orbackward.Seat reclinerAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips
Using the armrest (if equipped)Push the release control to movethe armrest up or down.Using the manual lumbar supportThe lumbar support control isloca
Adjusting the front power seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the sea
Memory seats/rearview mirrors/adjustable pedals (if equipped)This system allows automaticpositioning of the driver seat,outside rearview mirrors, anda
• There is a filter located underboth front seats.• It can be accessed from thesecond row seat. Move the frontseat all the way forward and upto ease a
To install climate controlled seat air filter:• First, position the filter in it’shousing making sure that the farforward end is all the way up inthe
Adjusting the 2nd row outboard seat for E-Z EntryThe 2nd row outboard seats allow for easier entry and exit to and fromthe 3rd row seat.To enter the 3
Engine oil pressure gauge:Indicates engine oil pressure. Theneedle should stay in the normaloperating range (between “L” and“H”). If the needle falls
3. To return the seat to a seatingposition, push down on the seatuntil the seat is latched to the floor.4. With the seat in the flat back position, li
1. Locate the handle on the side ofthe seat, lifting it to release theseatback.2. Ensure that the seat back islocked in the down position byapplying p
The rear latch hooks mustbe properly engaged withthe floor striker. Position the rearlegs of the seat over the floorstrikers and engage.2. With the se
Folding the 20% seat system (if equipped)1. Locate the release strap locatedbetween the front cushion and theseat back, and pull the strap torelease t
Before returning the seatback to its original position, make surethat cargo or any objects are not trapped underneath theseatback. After returning the
Third row seatsEnsure that no objects such as books, purses or briefcases are on thefloor in front of the third row seats or on the seat cushion befor
Folding down the third row seat to the load floorTo prevent possible damage to the seat or safety belts, ensurethat the safety belts are not buckled w
Push the top of the control buttonto return the seatback to its originalposition.The power fold down seats will operate for 30 minutes after theigniti
How does the Personal Safety System姟 work?The Personal Safety System娂 can adapt the deployment strategy of yourvehicle’s safety devices according to c
safety belt pretensioner activation depending upon safety belt usage.Refer to Safety restraints section in this chapter.Front safety belt pretensioner
PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED)1. EJ (Eject): Press to stop andeject a tape.2. EJ (Eject): Press to stop andeject a CD.3. BASS:
Safety restraints precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injur
Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Checkseat covers and buckle
sharply, or the vehicle receives an impact of approximately 5 mph (8km/h) or more, the combination safety belts will lock to help reduceforward moveme
How to disengage the automatic locking modeUnbuckle the combination lap and shoulder belt and allow it to retractcompletely to disengage the automatic
Front and second row safety belt height adjustmentYour vehicle has safety belt heightadjustments for the driver, rightfront passenger and second rowou
Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ
Conditions of operationIf... Then...The driver safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt warni
If... Then...The driver’s and front passenger’ssafety belts are buckled before theignition switch is turned to the ONposition or less than 1-2 minutes
Reasons given... Consider...“Belts areuncomfortable”We design our safety belts to enhance comfort. Ifyou are uncomfortable - try different positions f
re-enable during the same ignition cycle if the occupant buckles andremains buckled for approximately 30 seconds. Confirmation is not givenfor the one
4. BAL (Balance): Allows you toshift speaker sound between theright and left speakers. Press BALthen press SEL to shift sound to the leftor right .FAD
• This will disable the BeltMinder娂 feature for that seating position if itis currently enabled. As confirmation, the restraint system warninglight wi
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right
Never place your arm over the air bag module as a deploying airbag can result in serious arm fractures or other injuries.To properly position yourself
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
impact sensors, the system wiring, the airbag system readiness light, theairbag back up power and the airbag ignitors).Determining if the system is op
Do not attempt to service, repair, or modify the Safety Canopy娂system, its fuses, the A, B, or C pillar trim, or the headliner on avehicle containing
• Two crash sensors mounted in the front doors (one on each side ofthe vehicle).• Two crash sensors located at the c-pillar behind the rear doors (one
Several Safety Canopy娂system components get hotafter inflation. Do not touch themafter inflation.If the Safety Canopy娂 system has deployed, the Safety
SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme
Seating and Safety Restraints 162Seating 162Safety restraints 177Airbags 191Child restraints 199Tires, Wheels and Loading 213Tire Information 215Tire
In CD mode, REW control reverses the CD within the current track.FF (Fast Forward): Works in tapeand CD modes.In the tape mode, tape directionautomati
belt will provide some protection, these children are still too small forlap/shoulder belts to fit properly, which could increase the risk of seriousi
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
Follow all instructions provided by the manufacturer of thebooster seat.Never put the shoulder belt under a child’s arm or behind theback because it e
• Put the safety belt in the automatic locking mode. Refer to Automaticlocking mode section in this chapter.• The second row center seat can be moved
1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly move the seat forwardand back to m
securely. If the child seat moves excessively, repeat Steps 5 through 6, orproperly install the child seat in a different position.Attaching child saf
• outboard seating positions• center seating position (ifequipped)3. Route the child safety seat tether strap under the head restraint(outboard seats)
5. Rotate the tether strap, and clipthe tether strap to the anchor onthe seat frame.6. Rotate the tether strap clip.7. Tighten the child safety seat t
11. AUTOSET: Press to set first sixstrong stations into AM, FM1 orFM2 memory buttons; press again toreturn to the original presetstations. If there ar
• You may need to pull back thetop of the hinged panel along thebottom of the seat back to accessthe tether anchor.4. Clip the tether strap through th
Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol:Never attach two LATCH child safe
Attach LATCH lower attachments of the child seat only to theanchors shown.If you install a child seat with rigid LATCH attachments, do not tightenthe
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary.
• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and
and one-half (1 1/2) times as well on the government course as a tiregraded 100. The relative performance of tires depends upon the actualconditions o
• Tire Identification Number (TIN): A number on the sidewall ofeach tire providing information about the tire brand andmanufacturing plant, tire size
Every day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires and adjust ifrequired.A
Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙blowout⬙,with unexpected loss of
To engage the speed sensitive volume feature, press and hold the volumecontrol for five seconds (with the radio on). Press SEL toincrease/decrease vol
when you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. Never “bleed” or reduce airpressure when
The installation of replacement tires with steel cord body plies in the tiresidewall may cause malfunction of the Tire Pressure Monitoring System(TPMS
Dissimilar spare tire/wheel information (if equipped)Failure to follow these guidelines could result in an increasedrisk of loss of vehicle control, i
Spare tire informationNote: If your vehicle is equipped with the tire pressure monitoringsystem (TPMS), the system indicator light will illuminate whe
Removing the spare tire1. Fold the rear seat down. Refer toRear seats in the Seating andsafety restraints chapter.2. Remove the jack handle andwinch e
1. Park on a level surface, activatehazard flashers and set the parkingbrake.2. Place gearshift lever in P (Park),turn engine OFF and block thediagona
6. Lift the vehicle so the tire is no further than 1 inch (2.5 cm) off theground when installing the spare tire.When one of the rear wheels is off the
To lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engine when yourvehicle
2. Slide the wheel partially underthe vehicle and install the retainerthrough the wheel center. Afterdoing so, pull on the cable to alignthe component
INFORMATION CONTAINED ON THE TIRE SIDEWALLFederal law requires tire manufacturers to place standardizedinformation on the sidewall of all tires. This
PREMIUM IN-DASH SIX CD SOUND SYSTEM (IF EQUIPPED)AUDIOPHILE SATELLITE READY AM/FM STEREO IN-DASH SIX CDRADIO (IF EQUIPPED)1. Seek: Press and releaseSE
7. H: Indicates the tire’s speed rating. The speed rating denotes thespeed at which a tire is designed to be driven for extended periods oftime under
10. Tire Ply Composition and Material Used: Indicates the number ofplies or the number of layers of rubber-coated fabric in the tire tread andsidewall
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE CAREImproper or inadequate vehicle maintenance can also cause tires to wearabnormally. Here are some of the important maintenance items:Tire wear
Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t
The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear.Tire rotationRotating your tire
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can
information placard (label). Driving on a significantly under-inflated tirecauses the tire to overheat and can eventually lead to tire failure.Under-i
parked. The Low Tire Warning Lamp will turn ON if the tire pressure is25% below the pressure listed on the Safety Compliance CertificationLabel (appro
2. REW (Rewind): In CD mode,press to reverse within the currenttrack.Fast forward: In CD mode, press until desired selection is reached.TEXT: TEXT is
Low Tire WarningLightCustomer Action RequiredSolid Warning Light 1. Check your tire pressure to ensure they areproperly inflated, refer to Inspecting
therefore it may take up to a minute for the light to turn off after youhave filled your tires to the recommended tire pressure.• If your vehicle has
interference, and (2) This device must accept any interference received,including interference that may cause undesired operation.The Tire Pressure Mo
capability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design performance. Before loadingyour vehi
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei
GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).
mandatory options, no cargo (internal or external), a tongue load of10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), a
6. If your vehicle will be towing a trailer, load from your trailer will betransferred to your vehicle. Consult this manual to determine how thisreduc
Special loading instructions for owners of pickup trucks andutility-type vehiclesFor important information regarding safe operation of this typeof veh
Treble: Press TREB; then pressSEL/ to decrease/increasethe treble output.7. Select: Use with Bass, Treble,Balance and Fade controls to adjustlevels an
Trailer towing (standard equipment):Your vehicle is equipped with a integrated trailer hitch and a Class I(4-pin) trailer electrical connector. The 4-
EngineRear axleratioMaximum GCWR -lb. (kg)Trailer weightrange (0 -maximum) lb. (kg)4x45.4L withstandardtrailer towpackageAll 11900 (5397) 0–6000 (0–27
Integrated hitch ratingThe standard integrated hitch has two ratings depending on mode ofoperation:• Weight carrying - requires a draw bar and hitch b
(Overdrive) for 10 seconds, then return the gearshift lever to P (Park)and release the brake. With the ignition still in the ON position, and alldoors
Driving while you towWhen towing a trailer:• Turn off the speed control. The speed control may shut offautomatically when you are towing on long, stee
When backing down a ramp during boat launching or retrieval:• do not allow the static water level to rise above the bottom edge ofthe rear bumper.• do
STARTINGPositions of the ignition1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval.2. ACCESSORY, allow
If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf
5. Turn the key to 3 (ON) withoutturning the key to 4 (START).Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to
3. After idling for a few seconds, apply the brake, shift into gear anddrive.Note: If the engine does not start within five seconds on the first try,t
compression feature when COMP OFF is displayed. Press the SELcontrol again to disable the feature when COMP ON is displayed.Setting the clock: Press M
Important ventilating informationIf the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least one inch (2.
The ABS operates by detecting the onset of wheel lockup during brakeapplications and compensates for this tendency. The wheels areprevented from locki
Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th
Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.STEERINGY
easier entry. When a door or the liftgate is opened, the systemmemorizes and maintains that height until either all doors are closed orthe vehicle’s s
Press the bottom portion of theswitch to turn off the airsuspension.LIMITED-SLIP AXLE (IF EQUIPPED)This axle provides added traction on slippery surfa
Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.
down, the system will again function normally. Anti-lock braking is notaffected by this condition and will function normally during thecool-down perio
The AdvanceTrac威 with RSC buttonallows the driver to control theavailability of the AdvanceTrac威with RSC system. The RSC systemstatus is indicated by
Do not alter or modify your vehicle’s suspension or steering; theresulting changes to the vehicle’s handling can adversely affectthe AdvanceTrac威 with
Press and hold the volume control for five seconds. Then press SEL toincrease () or decrease ( ) the volume setting. The level willappear in the displ
3. Locate the round access plug onthe underside of the steeringcolumn cover.4. Remove the access plug using a flat-head screwdriver, then insert yourf
slightly delayed. Once the engine coolant temperature reaches 160°F(71°C) the normal shift strategy will resume. This is normal operationand will not
D (Drive) with OverdriveThe normal driving position for thebest fuel economy. Transmissionoperates in gears one through four.D (Drive) without Overdri
1 (First)Use 1 (Low) to provide maximumengine braking on steepdowngrades. Upshifts can be madeby shifting to 2 (Second) or to D (Drive). Selecting 1 (
To help avoid personal injury, please read and understand thelimitations of the reverse sensing system as contained in thissection. Reverse sensing is
The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to th
CONTROL TRAC FOUR-WHEEL DRIVE (4X4) OPERATION(IF EQUIPPED)For important information regarding safe operation of this typeof vehicle, see Preparing to
Positions of the Control Trac systemThe Control Trac system functionsin four modes:• 2H (2WD HIGH) delivers powerto the rear wheels only. This isappro
Utility and four-wheel drive vehicles are not designed forcornering at speeds as high as passenger cars any more thanlow-slung sports cars are designe
Shifting from 2H, A4WD or 4H to 4L1. Bring the vehicle to a stop andkeep the brake pedal depressed.2. Place the gearshift in N (Neutral).3. Move the c
For information regarding SIRIUS Satellite Radio, please call toll-free888-539-SIRIUS (888-539-7474) or visit the SIRIUS website atwww.siriusradio.com
How your vehicle differs from other vehiclesTruck and utility vehicles can differ from some other vehicles. Yourvehicle may be higher to allow it to t
Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.
called for. Avoid abrupt steering, acceleration or braking which couldresult in an increased risk of loss of vehicle control, vehicle rolloverand/or p
momentary clunk and ratcheting sounds. This is the front drivetraincoming up to speed and engaging the front wheels, and is not cause forconcern.SandW
slowly and avoid spinning your wheels. If the vehicle does slide, steer inthe direction of the slide until you regain control of the vehicle.If the tr
Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;
Company strongly recommends that you do not make modifications suchas adding or removing parts (such as lift kits or stabilizer bars) or byusing repla
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
The fuel pump shut-off switch has ared reset button on top of it and islocated beneath the air suspensionswitch (if equipped).Use the following proced
4. BAL (Balance): Allows you toshift speaker sound between theright and left speakers. Press BALthen press TEXT/SEL to shift soundto the leftor right
Note: Always replace a fuse with one that has the specified amperagerating. Using a fuse with a higher amperage rating can cause severe wiredamage and
To remove the trim panel for accessto the fuse box, pull the paneltoward you and swing it out awayfrom the side and remove it. Toreinstall it, line up
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 7.5A* Run/Accessory - Front wipermotor, In
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description5 7.5A* Powertrain Control Module (PCM)(KA power), Speed controldeactivatio
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description12 15A* Fuel pump relay, Fuel pumpshut-off switch, Fuel pump drivermodule,
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description20 30A* BSM (door locks, liftgate glassrelease relay), Liftgate glassreleas
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description29 30A* Trailer tow electric brakecontroller, Trailer tow 7–wireconnector (
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description41 20A* Cigarette lighter, OBD IIdiagnostic connector42 10A* Trailer tow le
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description115 30A** Transfer case shift motor, 4x4relays116 40A** Front blower motor
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionR203 PCM relay Fuse 32, Fuse 34, PCM solenoidsand sensorsR301 Trailer towba
Maintenance and Specifications 323Engine compartment 325Engine oil 326Battery 330Engine Coolant 332Fuel information 338Air filter(s) 352Part numbers 3
FF (Fast Forward): Works in tapeand CD modes.In the tape mode, tape directionautomatically reverses when the end of the tape is reached. Fast forwardi
may have firm and/or soft shifts. This operation is considered normal andwill not affect function or durability of the transmission. Over time, theada
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
4. Make the final connection of the negative (-) cable to the jumpstarting stud located in the rear of the engine compartment, near thebattery. Do not
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
If the vehicle is towed by other means or incorrectly, vehicledamage may occur.With a disabled vehicle (without access to wheel dollies, car haulingtr
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
• Folder/Track mode: In MP3 mode, press MENU until MODE appearsin the display. Use SEL to toggle between FOLDER (only tracks withinthe selected folder
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai
Board membershipThe Board consists of:• Three consumer representatives• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa
Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral
concern have been unsatisfactory, Ford of Canada participates in animpartial third party mediation/arbitration program administered by theCanadian Mot
details about Ford Extended Service Plan coverage options, or visit theFord ESP website at www.ford-esp.com.GETTING ASSISTANCE OUTSIDE THE U.S. AND CA
Or call:For a free publication catalog, order toll free: 1-800-782-4356Monday-Friday 8:00 a.m. - 6:00 p.m. ESTHelm, Incorporated can also be reached b
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
roof racks, bumper step surfaces, mirror housings or the windshieldcowl area. The paint sealant will “gray” or stain the parts over time.PAINT CHIPSYo
• Cover the highlighted areas to prevent water damage when cleaningthe engine.• 5.4L 3V engine• Never wash or rinse the engine while it is running; wa
Do not use sharp objects, such as a razor blade, to clean theinside of the rear window or to remove decals, as it may causedamage to the rear window d
17. TAPE: Press to begin tape play.Press to switch tape side (1 to 2) or(2 to 1).18. CD slot: Insert the disc with the playing side down and printed s
LEATHER SEATS(IF EQUIPPED, EXCEPT FOR THE KING RANCH EXPEDITION)Your leather seating surfaces have a clear, protective coating over theleather.For Kin
• Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl or plastics.ScratchesIn order to lessen th
Motorcraft Car Wash (Canada only) (CXC-21)Motorcraft Custom Bright Metal Cleaner (ZC-15)Motorcraft Custom Clear Coat Polish (ZC–8–A)Motorcraft Custom
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide sc
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel.2. Go to the front of the vehicle a
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT5.4L 3V– V8 engines1. Battery2. Automatic transmission fluid dipstick3. Air filter assembly4. Engine o
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
4. Open the hood. Protect yourself from engine heat.5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clea
• If required, add engine oil to theengine. Refer to Adding engineoil in this chapter.• Do not overfill the enginewith oil. Oil levels above thismark
Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oil.Only use oils “Certified For Gasoline Engines” by t
AUDIOPHILE/PREMIUM SATELLITE COMPATIBLE AM/FM STEREOIN-DASH SIX CD/MP3 RADIO (IF EQUIPPED)1. SEEK: Press and releaseSEEK/ for previous/nextstrong stat
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How
Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lightedsubstances to come near th
battery. When the battery is disconnected or a new battery is installed,the engine must relearn its idle and fuel trim strategy for optimumdriveabilit
concentration testing is possible with a hydrometer or antifreeze tester(such as the Rotunda Battery and Antifreeze Tester, 014–R1060). Thelevel of co
low or empty, add engine coolant to the reservoir. Refer to Addingengine coolant in this chapter.Note: Automotive fluids are not interchangeable; do n
• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcoholand other liquids can cause en
necessary, add enough 50/50 concentration of engine coolant anddistilled water to bring the liquid level to the proper level.If you have to add more t
• Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may cause engine da
Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to a service facility as soon as possible to minimize enginedamage.W
Automotive fuels can cause serious injury or death if misused ormishandled.Gasoline may contain benzene, which is a cancer-causing agent.Observe the f
3. AUX: Press to toggle between thecurrent playing media and DVD (ifequipped).4. MUTE: Press to MUTE playingmedia; press again to return toplaying med
When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke whilerefueling. Fuel vapor is extreme
2. Carefully turn the filler cap counterclockwise 1/4 turn until it stops.3. Pull to remove the cap from the fuel filler pipe.4. To install the cap, a
Repairs to correct the effects of using a fuel for which your vehicle wasnot designed may not be covered by your warranty.Octane recommendationsYour v
• Your Service engine soon indicator may come on. For moreinformation on the Service engine soon indicator, refer to theInstrument Cluster chapter.Fue
• Use the same filling rate setting (low — medium — high) each timethe tank is filled.• Allow no more than two automatic click-offs when filling.• Alw
• Idling for long periods of time (greater than one minute) may wastefuel.• Anticipate stopping; slowing down may eliminate the need to stop.• Sudden
• Using fuel blended with alcohol may lower fuel economy.• Fuel economy may decrease with lower temperatures during the first8–10 miles (12–16 km) of
emission control, such non-Ford parts should be equivalent to genuineFord Motor Company parts in performance and durability.Do not park, idle, or driv
These temporary malfunctions can be corrected by filling the fuel tankwith good quality fuel and/or properly tightening the fuel cap. After threedrivi
1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center o
Traffic (if equipped): Allows you to hear traffic broadcasts. With thefeature ON, press SEEK or SCAN to find a station broadcasting a trafficreport (i
temperature (approximately 20 miles [30 km]). If your vehicle has beenoperated for an extended period at high speeds, in city traffic during hotweathe
The transmission fluid should be inthis range if at ambient temperature(50°F-95°F [10°C-35°C]).High fluid levelFluid levels above the safe rangemay re
When changing the air filter element, use only the Motorcraft air filterelement listed. Refer to Motorcraft part numbers in this chapter.Note: Do not
MOTORCRAFT PART NUMBERSComponent 5.4L 3V V8 engineAir filter element FA-1754Battery BXT-65-650Fuel filter FG-986BOil filter FL-820-SPCV valve1Spark pl
REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to line onreservoi
Fluid Ford PartNameApplication CapacityEngine coolant3MotorcraftPremium GoldEngine Coolant(yellow-colored)5.4L BaseRadiator withoutaux rear heat19.4 q
Some transmission fluids may be labeled as dual usage, such asMERCON威 and MERCON威 V. These dual usage fluids are not to be usedin an automatic transmi
LUBRICANT SPECIFICATIONSItemFord partnameFord partnumberFordspecificationHinges, latches,striker platesand rotors, seattracks, fuel fillerdoor hinge a
ItemFord partnameFord partnumberFordspecification4x4 front wheelbearings, 4x4spindle needlebearings, spindlethrust bearings& front driveaxle u-joi
in an automatic transmission that requires use of the MERCON威 typefluid. However, these dual usage fluids may be used in transmissions thatrequire the
10. REPEAT: Press to repeat thecurrent CD/MP3 track.11. SHUFFLE: Press play theCD/MP3 tracks on the current discin random order.12. FOLDER: Press to a
Vehicle dimensions 4x2 – inches (mm) 4x4 – inches (mm)(4) Wheelbase 119.0 (3023) 119 (3023)(5) Track - Front 67.0 (1701) 67.0 (1701)(5) Track - Rear 6
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety ComplianceCertification
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake type and Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford
Interior styleElectrochromatic compass/temperature interior mirrorsFloor matsScuff platesLifestyleBike racksCargo organization and managementSmoker’s
• Mobile communications systems may harm the operation of yourvehicle, particularly if they are not properly designed for automotiveuse.• To avoid int
AABS (see Brakes) ...260Accessory delay ...122Air cleaner filter ...351–353Air conditioning ...
wiper blades ...318Climate control (see Airconditioning or Heating) ...96Clock adjust6-CD in dash ...
change oil soon warning,message center ...326checking and adding ...326dipstick ...326
Inspection/maintenance (I/M)testing ...348Instrument panelcleaning ...319cluster
20. Load: Press to load a CD. Pressand hold to load up to six discs.21. CD: Press to enter CD mode.CD units are designed to play commercially pressed
PPanic alarm feature, remoteentry system ...152Parking brake ...262Parts (see Motorcraft parts) ..
Steering wheelcontrols ...128tilting ...116TTire Pressure MonitoringSystem (TPMS)
372
373
374
376
REAR SEAT RADIO CONTROLS (IF EQUIPPED)If your vehicle is equipped with afront row console, then it is alsoequipped with rear seat radiocontrols.If you
To activate Dual Play mode (rearseat passengers listen to a differentplaying media than the front seatpassengers):• Press the speaker/headphonecontrol
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
Turning the rear speakers on and offPress the headphone/speakercontrol to turn the rear speakers on(Single Play mode) or off (Dual Playmode).Using hea
Memory preset controlPush the MEMORY/MEM controlsuccessively to allow rear seatpassengers to scroll through the 6memory presets in AM, FM1 orFM2.Push
RADIO FREQUENCIESAM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsComm
Don’t:• Expose discs to direct sunlight or heat sources for extended periodsof time.• Insert more than one disc into each slot of the CD changer magaz
DVD player controls1. MAIN control• NEXT — Press to access the next track on the CD, the next chapteron the DVD, or to go up in cursor mode.• PREV — P
7. Auxiliary jacksInsert lines for standard video game players.8. STOP/EJECT controlPress once to stop DVD play. Press again to eject the DVD.9. DISPL
• Press the FWD control to movethe cursor right one positionNext/Previous controlThe NEXT (up) and PREV (down)controls allow you to access thenext or
FWD or REV control for slow motion playback. Three different speedsare available depending on how long the control is held. Press thecontrol once for
Remote control1. REWIND controlPress to reverse the direction of the DVD movie.2. FAST FORWARD controlPress to advance the direction of the DVD movie.
In stop mode, press to change to a different playing media (e.g. AM, FM,CD...)8. VOLUME controlPress to increase (+) or decrease (-) volume level.Batt
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
To install the batteries, lightly pressdown on the top of the left earpieceand slide the cover off.When replacing the batteries, usetwo new batteries
Liquid Crystal Display (LCD) flip-down screenThe screen rotates down to view and into the housing to store when notin use. Be sure the screen is latch
• When the temperature of the DVD player becomes too hot, the hightemperature sensor circuit stops machine operation. DVD/CD HOT willilluminate in the
Inserting a CD/DVD into the DVD player automatically turns the powerON and playback should begin.The counter is automatically reset to 0:00:00.Removin
1. CD track2. DVD chapter3. SYSTEM COUNTER — displays current viewing time of desired media.(HOURS:MINUTES:SECONDS)4. DVD/ CD STATUS (PLAY/FF/REW/PAUS
Whenever a warning is received, the radio volume will be loweredto a volume that will allow the tones to be heard. The radiovolume will return to the
moisture condensation occurs, do not insert a CD or DVD into theplayer. If one is already in the player, remove it. Turn the DVD player ONto dry the m
Safety informationPlease read and follow all stated safety precautions. Failure to doso may increase your risk of collision and personal injury.Ford M
• For road safety reasons, the driver should program the system onlywhen the vehicle is stationary. Certain functions will therefore notoperate while
location as home. Pressing the home key after the home location hasbeen set will calculate a route to that set home location.2. Eject: Press this cont
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
When in RSC mode, Dual Play mode can be enabled and disabled by theRSC, or by pressing Preset 2 and 4 simultaneously on the Navigationradio system. Th
14. MENU: The MENU controlworks in both the audio andnavigation mode. Press to accessvarious menus in both modes.15. HERE: The HERE control worksin th
3. Press the memory presets tochoose the desired disc in the CDDJ.Note: Navigation CD’s are not operational in the CD DJ.To use the Navigation system:
Volume/power controlPress the control to turn theaudio/navigation system on or off.Turn the control to raise or lower volume. The levels will be displ
5. Use the cursor control to increaseor decrease the levels. The higherthe level selected, the greater thecompensation. The levels will beshown in the
CD selectTo begin CD play (if a CD is alreadyloaded), press the CD control. Thefirst track of the disc will beginplaying. After that, CD play willbegi
4. Use the cursor control to increaseor lower the bass and treble levelsor to adjust the sound between thefront and rear or between the leftand right
Rewind/fast forwardPress theand controlsto fast forward or rewind a CDtrack.Seek functionThe SEEK control works in allmodes.Seek in radio mode• Presst
Setting memory preset stations1. Select the frequency band with the AM/FM select control.2. Select a station. Refer to Tune adjust or Seek function fo
Tune adjustThe tune feature works in radiomode.• Select the TUNE soft key.• Press SEEK to go upordown the frequency bandmanually.Stereo indicatorWhene
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental restraint
Select the TRAF soft key to select traffic information broadcast fromcertain stations which will automatically interrupt radio or CD playbackat a pres
Press the CD control until DVDappears in the display.(EJECT) — Press to stop DVD and eject the DVD disc.(PLAY) / II (PAUSE) — Press to play/pause the
To access the CD DJ:Slide the door to access the CD DJmagazine.Pressto eject the magazine.1. Pull the lever to remove a CDtray from the magazine.2. In
3. Insert each CD tray, with the discloaded, all the way into the CDmagazine.4. Insert the CD magazine into theCD DJ.5. Slide the door to the left to
Ensure that the disc holder isevenly inserted and at the samelevel as the magazine (A). The unitwill not operate if the disc holder isnot inserted at
Rewind/fast forward featureWhen in CD DJ mode, press andhold theor control tosearch forward or in reverse on thecurrent disc.Scan featureWhen in CD DJ
Rear seat controls (RSC)Your vehicle is equipped with rear seat controls, which allow the rearseat passengers to operate and listen to a different pla
Please drive safelyThis screen may appear on yourVNR display. Press the soft key nextto the display to select the desiredlanguage. Press the control n
Limited GPS receptionSystem performance may be adversely affected if GPS reception isinterrupted or interference occurs over a distance of several mil
Map display informationWhen using the navigation system,the map display screen will appearto guide you to your location. Onthe screen, you are able to
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
Address/IntersectionUse the soft keys to selectAddress/Intersection from theDestination Entry menu. The nexttwo options available are:• Town/City Name
• Within a Town/City – Lists entries for a specific city in alphabeticalorder.Certain categories may not be available in some areas and POIs may notal
• To move back to previously selected characters, press DELETE.List – Your VNR system shows a list of town/cities, streets or points ofinterest and a
This screen will appear for a fewseconds while the navigation systemis calculating your route.Please proceedOnce the route is calculated, ’PleaseProce
Guide displayOnce your vehicle is moving alongthe highlighted route, the Guidedisplay screen will automaticallyappear. This screen shows your nextturn
ArrivalWhen you approach yourdestination, the destination indicatorwill appear on the map displayscreen as a circular icon. When youarrive, the name a
6. Press the EDIT soft key to editthe current entry.• Use the cursor control to select aletter.• Push the control to add a letterto the name. If you m
Detours, route interruptions and changesIf need be, your navigation systemcan easily and quickly find the mostefficient detour around roadconstruction
• Resume route - The navigationsystem displays the Select RouteCriteria screen. Refer toSelecting Route Criteria earlierin this chapter.• Cancel route
• UNITS — Press to select from miles or kilometers. When kilometersare selected, it will affect the map and the fuel economy screen.Display optionsUse
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
2. Press the ADJUST control toselect the hours or minutes to set.3. Use the cursor control to increaseor decrease the hours or minutes.4. Press DONE t
• Always store the map CDs in their protective cases when not in use.Map coverageThe following map data CDs are available for the navigation system:•
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
• To reduce humidity build up inside the vehicle: do not drive with theair flow selector in the O (OFF) or (in cold weather) MAX A/Cposition.• Under n
DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM(IF EQUIPPED)1. A/C control: Uses outside air tocool the vehicle. Press to turn on/offin all modes exc
5. DUAL (Single/dual electrictemperature control): Allows thedriver to have full control of thecabin temperature settings (single zone) or allows the
16. Temperature conversion:Press to toggle between Fahrenheitand Celsius temperature on theDATC display only. The set point temperatures in Celsius wi
Will work in all modes except defrost. In automatic operation, therecirculated air operates automatically as necessary to achieve theselected temperat
9. OFF: Outside air is shut out andthe fan will not operate.10. Manual override controls: Allows you to manually select whereairflow is directed. To r
16. EXT control: Press to displaythe outside air temperature. Pressagain to return to interiortemperature. Note: Exterior readings are most accurate w
Commentaires sur ces manuels