Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 14Entertainment Systems 18AM/FM stereo cassette with CD 18AM/FM stereo with in-
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
AUXILIARY A/C-HEATER CONTROLS (IF EQUIPPED)Your vehicle may be equipped with auxiliary climate controls. Theseallow the front or rear seat passengers
Rear auxiliary controls (if equipped):Once the front auxiliary control is set to REAR, the rear seat passengersmay use the rear auxiliary controls in
HEADLAMP CONTROLRotate the headlamp control to thefirst positionto turn on theparking lamps. Rotate to the secondpositionto turn on theheadlamps.Fogla
Daytime running lamps (DRL) (if equipped)Turns the foglamps on at full intensity output. To activate:• the ignition must be in the ON position and• th
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parklamp operatio
5. Locate the vertical adjuster oneach headlamp, then use a 10 mmsocket/wrench to turn the adjustereither counterclockwise (to adjustdown) or clockwis
Front row map/dome lamp (if equipped)The dome lamp lights when:• any door is opened,• the instrument panel dimmerswitch is rotated up until thecourtes
Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America to
Replacing the interior bulbsCheck the operation of all bulbs frequently.Map lampsTo change the map lamp bulbs:1. Use a small screwdriver toremove the
7. Once the bulb covers areremoved, the bulbs can be removedby turning them counterclockwiseand then pulling the bulbs straightout.Handle a halogen he
Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interiorfloor coverings or other
6. Rotate the bulb socketcounterclockwise and remove fromthe lamp assembly.7. Carefully pull the bulb out of thesocket and push in the new bulb.8. Ins
Replacing foglamp bulbsHandle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and donot tou
Replacing license plate lamp bulbThe license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate
Approach lamp bulb removal (if equipped)To change the bulbs:1. Make sure that all the doors areclosed and the interior lights haveautomatically turned
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
Changing the wiper bladesIt is recommended that wiper blades are renewed before winter.To replace the wiper blades:1. Fold back the wiper arm andposit
TILT STEERINGPush the lever down to unlock thesteering column. While the lever isin the down position, tilt thesteering column to the desiredposition.
Forward storage bin and conversation mirror (if equipped)The storage compartment may beused to store two pairs of sunglassesor similar objects. Press
To vent the moon roof: Press and hold the control. The moonroof must be in the closed position in order to move it into thevent position. To close, pr
Do not plug optional electricalaccessories into the cigarette lighter.Use the power point.Do not use the power point foroperating the cigarette lighte
Air bag readiness: If this light failsto illuminate when ignition is turnedto ON, continues to flash or remainson, have the system servicedimmediately
Not equipped with rear climatecontrolPOWER WINDOWS (IF EQUIPPED)Do not leave children unattended in the vehicle and do not letchildren play with the p
Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controlsexcept for the driver’s press
1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror.2. Move the control in the d
Powerfold mirrors (if equipped)Pull the switch rearwards to autofold in and rearwards again to autofold back to design position.Powerfold the side mir
Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas
Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RES contro
• Depress the brake pedal until thedesired vehicle speed is reached,press the SET + control.Turning off speed controlThere are two ways to turn off th
Audio control featuresPressto select:• AM, FM1, FM2,• CD, or• DVD (if equipped).In AM, FM1, or FM2 mode:• Press MEM to select presetstations within th
Climate control featuresPress TMP + or - to adjusttemperature.Press+ or - to adjust fan speed.HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED)The HomeL
Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink威 equipped vehiclepurchase). I
Check fuel cap (if equipped):Illuminates when the fuel cap maynot be properly installed. Continueddriving with this light on may causethe Service engi
5. Press and hold the just-trained HomeLink威 button and observe theindicator light. If the light is constant, programming is complete and yourdevice s
seconds (“cycle”) your hand-held transmitter until the frequencysignal has been accepted by the HomeLink威. The indicator light willflash slowly and th
For questions or comments, contact HomeLink威 at www.homelink.comor 1–800–355–3515.ELECTRONIC COMPASS/TEMPERATURE DISPLAY WITHOUTMESSAGE CENTER (IF EQU
Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the ON p
4. Drive the vehicle slowly (less than 3 mph [5 km/h]) in circles untilCAL indicator turns off. As many as 5 complete circles may be required.5. The c
Compass displayThe compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antenna. Magneticor
7. To exit the zone setting mode,and to “lock in” your change, pressand release the RESET control.Perform compass calibration in an open area free fro
Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in miles/gallon or liters/100 km.If you calculate
To turn the display off or change the display from English to metric seeyour dealer.Setup menuPress this control for the followingdisplays:• System Ch
1. To disable/enable the autolampdelay feature, select this functionfrom the SETUP control for thecurrent display mode.2. Press the RESET control to s
four-wheel drive is engaged. If the light fails to illuminate when theignition is turned ON, continues to flash or remains on, have the systemserviced
System checkSelecting this function from theSETUP menu causes the messagecenter to cycle through each of thesystems being monitored. For eachof the mo
• They will reappear on the display ten minutes from the reset.• They will not reappear until an ignition OFF-ON cycle has beencompleted.This acts as
PARK ASSIST ON/OFF (if equipped). Displayed when thetransmission is in R (Reverse) and the Backup Aid is disabled. Refer toBackup Aid in this section
TIRE PRESSURE SENSOR FAULT (if equipped). Displayed when atire pressure sensor is malfunctioning, or your spare tire is in use. Formore information on
ADVTRAC OFF T/C ON with RSC (if equipped). Displayed on 4x4vehicles only when 4x4 Low Range is selected. In this mode, the stabilityenhancement portio
CENTER CONSOLE (IF EQUIPPED)The center console offers several useful storage features. These include:1. Pen holder2. Tissue holder3. Large utility com
POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)Position the floor mat so that theeyelet is over the pointed end of theretention post and rotate forward tol
LUGGAGE RACKYour vehicle is equipped with a roofrack. The maximum recommendedload is 200 lbs (90 kg), evenlydistributed. If it is not possible todistr
KEYSOne key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency.Your keys are programmed to your v
Childproof door locksWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo
Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,
Unlocking the doors/liftgatePress this control to unlock thedriver’s door. The interior lamps willilluminate with the ignition is in the1 (OFF/LOCK) p
Sounding a panic alarmPress this control to activate thealarm.The personal panic alarm will cyclethe horn and parking lamps on/off.To deactivate the a
Deactivating the memory seat featureTo deactivate this feature:1. Press the SET control on the driver’s door panel.2. Within 5 five seconds, press any
Note: Replacement of the battery will not cause the remote transmitterto become deprogrammed from your vehicle. The remote transmittershould operate n
Illuminated entryThe lamps illuminate when the remote entry system is used to unlockthe door(s).The system automatically turns off after 25 seconds or
KEYLESS ENTRY SYSTEMWith the keyless entry keypad, you can:• lock or unlock the vehicle doors without using the key,• release the liftgate glass,• ena
Programming your own personal entry codeTo program your own code:1. Enter the factory set code (keypad will illuminate when pressed).2. Press the 1 •
To lock all doors, liftgate and liftgate window, press the 7 • 8 andthe 9 • 0 at the same time. Note: The driver’s door must be closed. Youdo not need
Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 1(OFF/LOCK) position.Automatic disarmingSwitching the ignition to
The correct coded key must be used for your vehicle. The use of thewrong type of coded key may lead to a “no start” condition.If an unprogrammed key i
• With Full Message CenterPress and release the messagecenter INFO button until TRIPmode appears in the display. Pressthe control again to select Trip
If successful, the new coded key(s) will start the vehicle’s engine and thetheft indicator will illuminate for three seconds and then go out.If not su
SEATINGFront row adjustable head restraintsYour vehicle’s seats are equipped with two-way adjustable headrestraints. The purpose of these head restrai
Lift handle to move seat forward orbackward.Seat reclinerAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips
Using the armrest (if equipped)Push the release control to movethe armrest up or down.Using the manual lumbar supportThe lumbar support control isloca
Adjusting the front power seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the sea
Memory seats/rearview mirrors/adjustable pedals (if equipped)This system allows automaticpositioning of the driver seat,outside rearview mirrors, anda
• There is a filter located underboth front seats.• It can be accessed from thesecond row seat. Move the frontseat all the way forward and upto ease a
To install climate controlled seat air filter:• First, position the filter in it’shousing making sure that the farforward end is all the way up inthe
Adjusting the 2nd row outboard seat for E-Z EntryThe 2nd row outboard seats allow for easier entry and exit to and fromthe 3rd row seat.To enter the 3
3. To return the seat to a seatingposition, push down on the seatuntil the seat is latched to the floor.4. With the seat in the flat back position, li
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe
Folding 40% seat system to full lowered load floor positionUse caution when folding the seatback to the flat back positionas the system will move forw
Returning to the upright position from full lowered load floorpositionThe seatback cannot be returned to the upright position until the seat isreturne
Folding the 20% seat system (if equipped)1. Locate the release strap locatedbetween the front cushion and theseat back, and pull the strap torelease t
Adjusting the second row 20% seat (if equipped)Lift the handle to move the seatforward or backward.Note: This seat can be moved forward to keep a chil
Third row adjustable head restraintsYour vehicle’s third row outboard seating positions are equipped withhead restraints which are vertically adjustab
Folding down the third row seat to the load floorTo prevent possible damage to the seat or safety belts, ensurethat the safety belts are not buckled w
Push the top of the control buttonto return the seatback to its originalposition.The power folding seats are designed to stall within 1–10 secondsof e
• Restraint system warning light and back-up tone.• The electrical wiring for the air bags, crash sensor(s), safety beltpretensioners, front safety be
Front safety belt usage sensorsThe front safety belt usage sensors detect whether or not the driver andfront outboard passenger safety belts are faste
If any of these things happen, even intermittently, have the PersonalSafety System serviced at your dealership or by a qualified technicianimmediately
PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED)1. EJ (Eject): Press to stop andeject a tape.2. EJ (Eject): Press to stop andeject a CD.3. BASS:
Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.Safety belts and seats can becom
movement. For example, if the driver brakes suddenly or turns a cornersharply, or the vehicle receives an impact of approximately 5 mph(8 km/h) or mor
How to disengage the automatic locking modeUnbuckle the combination lap and shoulder belt and allow it to retractcompletely to disengage the automatic
Front and second row safety belt height adjustmentYour vehicle has safety belt heightadjustments for the driver, rightfront passenger and second rowou
Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ
Conditions of operationIf... Then...The driver safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt warni
If... Then...The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition...The BeltMinder娂 feature will notactivate.The p
Reasons given... Consider...“Belts wrinkle my clothes” Possibly, but a serious crash can domuch more than wrinkle your clothes,particularly if you are
• The ignition switch is in the OFF position• All vehicle doors are closed• The driver’s safety belt is unbuckled• The parklamps/headlamps are in OFF
Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label.
4. BAL (Balance): Allows you toshift speaker sound between theright and left speakers. Press BALthen press SEL to shift sound to the leftor right .FAD
Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in
Do not attempt to service, repair, or modify the air bagsupplemental restraint systems or its fuses. See your Ford orLincoln Mercury dealer.The front
How does the air bag supplemental restraint system work?The air bag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suff
Several air bag system components get hot after inflation. Do nottouch them after inflation.If the air bag has deployed, the air bag will not function
Safety Canopy姟 system (if equipped)Do not place objects ormount equipment on ornear the headliner at the siderailthat may come into contact with adepl
How does the Safety Canopy姟 system work?The design and development of theSafety Canopy娂 system includedrecommended testing proceduresthat were develop
The Safety Canopy娂 is mounted to roof side-rail sheet metal, behind theheadliner, above the first and second row seats. In certain lateralcollisions o
Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref
Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.Alwa
When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the
Seating and Safety Restraints 161Seating 161Safety restraints 176Air bags 189Child restraints 197Tires, Wheels and Loading 212Tire Information 215Tire
In CD mode, REW control reverses the CD within the current track.FF (Fast Forward): Works in tapeand CD modes.In the tape mode, tape directionautomati
• Those with a high back.If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo
SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully fo
tether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. Formore info
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a
Installing child safety seats in the center front seating positionAlways transport children 12 years old and under in the rearseats and always properl
• Second row bench seat• Second row bucket seatsAttach the tether strap only to the appropriate tether anchor asshown. The tether strap may not work p
• center seating position (ifequipped)3. Route the child safety seat tether strap under the head restraint(outboard seats) and over the back of the se
6. Rotate the tether strap clip.7. Tighten the child safety seat tether strap according to themanufacturer’s instructions.Third row seating position1.
4. Clip the tether strap through theanchor loop as shown.If the tether strap is clippedincorrectly, the child safetyseat may not be retained properlyi
11. AUTOSET: Press to set first sixstrong stations into AM, FM1 orFM2 memory buttons; press again toreturn to the original presetstations. If there ar
Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol:Never attach two LATCH child safe
Attach LATCH lower attachments of the child seat only to theanchors shown.If you install a child seat with rigid LATCH attachments, do not tightenthe
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary.
• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and
and one-half (1 1/2) times as well on the government course as a tiregraded 100. The relative performance of tires depends upon the actualconditions o
• Tire Identification Number (TIN): A number on the sidewall ofeach tire providing information about the tire brand andmanufacturing plant, tire size
Every day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires and adjust ifrequired.A
Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙blowout⬙,with unexpected loss of
when you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. Never “bleed” or reduce airpressure when
Speed sensitive volume (if equipped): Automatically changes thevolume with vehicle speed to compensate for road and wind noise. Therecommended level i
The installation of replacement tires with steel cord body plies in the tiresidewall may cause malfunction of the Tire Pressure Monitoring System(TPMS
different in brand, size or appearance from the road tires and wheels. Ifyou have a dissimilar spare tire/wheel, then it is intended for temporaryuse
If your vehicle is equipped with TPMS, have a flat tire serviced by adealer or qualified technician in order to prevent damage to the TPMSsensor, refe
Removing the spare tire1. Fold the rear seat down. Refer toRear seats in the Seating andsafety restraints chapter.2. Remove the jack handle andwinch e
1. Park on a level surface, activatehazard flashers and set the parkingbrake.2. Place gearshift lever in P (Park),turn engine OFF and block thediagona
6. Lift the vehicle so the tire is no further than 1 inch (2.5 cm) off theground when installing the spare tire.When one of the rear wheels is off the
To lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engine when yourvehicle
2. Slide the wheel partially underthe vehicle and install the retainerthrough the wheel center. Afterdoing so, pull on the cable to alignthe component
INFORMATION CONTAINED ON THE TIRE SIDEWALLFederal law requires tire manufacturers to place standardizedinformation on the sidewall of all tires. This
7. H: Indicates the tire’s speed rating. The speed rating denotes thespeed at which a tire is designed to be driven for extended periods oftime under
PREMIUM IN-DASH SIX CD SOUND SYSTEM (IF EQUIPPED)AUDIOPHILE SATELLITE READY AM/FM STEREO IN-DASH SIX CDRADIO (IF EQUIPPED)REVIEW COPY2005 Expedition (
10. Tire Ply Composition and Material Used: Indicates the number ofplies or the number of layers of rubber-coated fabric in the tire tread andsidewall
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE CAREImproper or inadequate vehicle maintenance can also cause tires to wearabnormally. Here are some of the important maintenance items:Tire wear
Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t
The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear.Tire rotationRotating your tire
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can
information placard (label). Driving on a significantly under-inflated tirecauses the tire to overheat and can eventually lead to tire failure.Under-i
parked. The Low Tire Warning Lamp will turn ON if the tire pressure is25% below the pressure listed on the tire label (approximately 6 to 9 psibelow t
Low Tire WarningLightCustomer Action RequiredSolid Warning Light 1. Check your tire pressure to ensure they areproperly inflated, refer to Inspecting
1. Seek: Press and releaseSEEK/ for previous/nextstrong station, selection or track.2. REW (Rewind): In CD mode,press to reverse within the currenttra
therefore it may take up to a minute for the light to turn off after youhave filled your tires to the recommended tire pressure.• If your vehicle has
interference, and (2) This device must accept any interference received,including interference that may cause undesired operation.The Tire Pressure Mo
capability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design performance. Before loadingyour vehi
Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue loador king pin w
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).
mandatory options, no cargo (internal or external), a tongue load of10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), a
6. If your vehicle will be towing a trailer, load from your trailer will betransferred to your vehicle. Consult this manual to determine how thisreduc
Loaded vehicles, with a higher center of gravity, may handledifferently than unloaded vehicles. Extra precautions, such asslower speeds and increased
for a customer supplied aftermarket electronic brake controller. Forinstalling a customer supplied electronic brake controller, a electricaljumper har
6. Bass: Press BASS; then pressSEL/ to decrease/increasethe bass output.Treble: Press TREB; then pressSEL/ to decrease/increasethe treble output.7. Se
EngineRear axleratioMaximum GCWR -kg (lb.)Trailer weightrange (0 -maximum) kg (lb.)Note: For vehicles not equipped with the optional trailer tow packa
Mode MaximumGross TrailerWeight - kg(lb.)MaximumTongue Weight- kg (lb.)Weight carrying 2721 (6000) 272 (600)Weight distributing 4060 (8950) 406 (895)T
5. Turn the air suspension (if equipped) control to ON.Note: Adjusting an equalizing hitch so the rear bumper of the vehicle ishigher than it was unlo
Understanding the positions of the 4–speed automatictransmission section in this chapter.• Anticipate stops and brake gradually.• Do not exceed the GC
• affecting driveability, emissions and reliability.Replace the rear axle lubricant any time the axle has been submerged inwater. Rear axle lubricant
STARTINGPositions of the ignition1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval.2. ACCESSORY, allow
If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf
5. Turn the key to 3 (ON) withoutturning the key to 4 (START).Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to
3. After idling for a few seconds, apply the brake, shift into gear anddrive.Note: If the engine does not start within five seconds on the first try,t
Important ventilating informationIf the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least one inch (2.
Compression: Brings soft and loud CD passages together for a moreconsistent listening level when in CD model. Press MENU untilcompression status is di
The ABS operates by detecting the onset of wheel lockup during brakeapplications and compensates for this tendency. The wheels areprevented from locki
Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th
Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.STEERINGY
easier entry. When a door or the liftgate is opened, the systemmemorizes and maintains that height until either all doors are closed orthe vehicle’s s
Press the bottom portion of theswitch to turn off the airsuspension.LIMITED-SLIP AXLE (IF EQUIPPED)This axle provides added traction on slippery surfa
Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.
down, the system will again function normally. Anti-lock braking is notaffected by this condition and will function normally during thecool-down perio
The AdvanceTrac娂 with RSC buttonallows the driver to control theavailability of the AdvanceTrac娂with RSC system. The RSC systemstatus is indicated by
Do not alter or modify your vehicle’s suspension or steering; theresulting changes to the vehicle’s handling can adversely affectthe AdvanceTrac娂 with
3. Locate the round access plug onthe underside of the steeringcolumn cover.4. Remove the access plug using a flat-head screwdriver, then insert yourf
Speed sensitive volume: Radio volume changes automatically andslightly with vehicle speed to compensate for road and wind noise.Recommended level is 1
slightly delayed. Once the engine coolant temperature reaches 160°F(71°C) the normal shift strategy will resume. This is normal operationand will not
D (Drive) with OverdriveThe normal driving position for thebest fuel economy. Transmissionoperates in gears one through four.D (Drive) without Overdri
1 (First)Use 1 (Low) to provide maximumengine braking on steepdowngrades. Upshifts can be madeby shifting to 2 (Second) or to D (Drive). Selecting 1 (
To help avoid personal injury, please read and understand thelimitations of the reverse sensing system as contained in thissection. Reverse sensing is
The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to th
CONTROL TRAC FOUR-WHEEL DRIVE (4X4) OPERATION(IF EQUIPPED)For important information regarding safe operation of this typeof vehicle, see Preparing to
Positions of the Control Trac systemThe Control Trac system functionsin four modes:• 2H (2WD HIGH) delivers powerto the rear wheels only. This isappro
Utility and four-wheel drive vehicles are not designed forcornering at speeds as high as passenger cars any more thanlow-slung sports cars are designe
Shifting from 2H, A4WD or 4H to 4L1. Bring the vehicle to a stop andkeep the brake pedal depressed.2. Place the gearshift in N (Neutral).3. Move the c
How your vehicle differs from other vehiclesTruck and utility vehicles can differ from some other vehicles. Yourvehicle may be higher to allow it to t
Press to scroll through a list of categories, (i.e., Pop, Rock, Country, HipHop, R&B, Dance, Jazz/Standards, Classical, Variety, News, Sports andE
Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.
called for. Avoid abrupt steering, acceleration or braking which couldresult in an increased risk of loss of vehicle control, vehicle rolloverand/or p
momentary clunk and ratcheting sounds. This is the front drivetraincoming up to speed and engaging the front wheels, and is not cause forconcern.SandW
slowly and avoid spinning your wheels. If the vehicle does slide, steer inthe direction of the slide until you regain control of the vehicle.If the tr
Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;
Company strongly recommends that you do not make modifications suchas adding or removing parts (such as lift kits or stabilizer bars) or byusing repla
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
The fuel pump shut-off switch has ared reset button on top of it and islocated beneath the air suspensionswitch (if equipped).Use the following proced
Note: Always replace a fuse with one that has the specified amperagerating. Using a fuse with a higher amperage rating can cause severe wiredamage and
TREB (Treble): Allows you toincrease or decrease the audiosystem’s treble output. Press TREBthen press TEXT/SEL todecreaseor increase the treble level
Passenger compartment fuse panel / power distribution boxThe fuse panel is located under the right-hand side of the instrumentpanel.To remove the trim
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 7.5A* Run/Accessory - Front wipermotor, In
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description5 7.5A* Powertrain Control Module (PCM)(KA power), Speed controldeactivatio
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description12 15A* Fuel pump relay, Fuel pumpshut-off switch, Fuel pump drivermodule,
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description20 30A* BSM (door locks, liftgate glassrelease relay), Liftgate glassreleas
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description29 30A* Trailer tow electric brakecontroller, Trailer tow 7–wireconnector (
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description41 20A* Cigarette lighter, OBD IIdiagnostic connector42 10A* Trailer tow le
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description115 30A** Transfer case shift motor, 4x4relays116 40A** Front blower motor
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionR203 PCM relay Fuse 32, Fuse 34, PCM solenoidsand sensorsR301 Trailer towba
Preparing your vehicleWhen the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, th
Maintenance and Specifications 321Engine compartment 323Engine oil 324Battery 327Fuel information 335Air filter(s) 349Part numbers 350Refill capacitie
9. REW (Rewind): Works in tapeand CD modes.In tape mode, radio play continuesuntil rewind is stopped (by pressing REW again) or the beginning of theta
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
4. Make the final connection of the negative (-) cable to the jumpstarting stud located in the rear of the engine compartment, near thebattery. Do not
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
If the vehicle is towed by other means or incorrectly, vehicledamage may occur.With a disabled vehicle (without access to wheel dollies, car haulingtr
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or
• available free to owners and lessees of qualifying Ford Motor Companyvehicles.The Dispute Settlement Board may not be available in all states. FordM
Press TEXT/SEL to increase /decrease volume compensationlevels. The selected level will appear in the display.• Compression: In CD/MP3 modes, select t
• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Board membership are recruited and trained byan independent consulting fi
before the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral presentationmay be
The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have
GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.
Or call:For a free publication catalog, order toll free: 1-800-782-4356Monday-Friday 8:00 a.m. - 6:00 p.m. ESTHelm, Incorporated can also be reached b
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam
• 5.4L 3V engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTIC (NON-PAINTED) EXTER
INSTRUMENT PANEL AND CLUSTER LENSClean the instrument panel with a damp cloth, then dry with a dry cloth.• Avoid cleaners or polish that increase the
LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• To clean, use a soft cloth with Motorcraft
“nominal” listening level when the ignition switch is turned back on.Audio power can also be turned on by pressing BAND or the TAPE orCD controls.17.
Motorcraft Wheel and Tire Cleaner (ZC-37–A)Motorcraft Dash and Vinyl Cleaner (ZC-38–A)Motorcraft Car Care Kit (ZC-26)Motorcraft Premium Car Wash Conce
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel.2. Go to the front of the vehicle a
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT5.4L 3V – V8 engines1. Battery2. Automatic transmission fluid dipstick3. Air filter assembly4. Engine
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
4. Open the hood. Protect yourself from engine heat.5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clea
2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler cap
Ford production and aftermarket (Motorcraft) oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedtha
Note: Electrical or electronic accessories or components added tothe vehicle by the dealer or the owner may adversely affectbattery performance and du
Because your vehicle’s engine is also electronically controlled by acomputer, some control conditions are maintained by power from thebattery. When th
AUDIOPHILE/PREMIUM SATELLITE COMPATIBLE AM/FM STEREOIN-DASH SIX CD/MP3 RADIO — LATE AVAILABILITY(IF EQUIPPED)1. SEEK: Press and releaseSEEK/ for previ
coolant concentration should be maintained at 50/50 coolant and distilledwater, which equates to a freeze point of -34°F (-36°C). Coolantconcentration
If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the reservoir islow or
• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcoholand other liquids can cause en
necessary, add enough 50/50 concentration of engine coolant anddistilled water to bring the liquid level to the proper level.If you have to add more t
• Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may cause engine da
Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to a service facility as soon as possible to minimize enginedamage.W
Automotive fuels can cause serious injury or death if misused ormishandled.Gasoline may contain benzene, which is a cancer-causing agent.Observe the f
When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke whilerefueling. Fuel vapor is extreme
be void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used.The fuel system may be und
Fuel qualityIf you are experiencing starting, rough idle or hesitation driveabilityproblems during a cold start, try a different brand of gasoline. If
3. AUX: Press to toggle between thecurrent playing media and DVD (ifequipped).4. MUTE: Press to MUTE playingmedia; press again to return toplaying med
possible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel economy. We do not recommendtaking fuel econ
3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading.4. Subtract your initial odometer reading fro
• Resting your foot on the brake pedal while driving may reduce fueleconomy.• Combine errands and minimize stop-and-go driving.Maintenance• Keep tires
It is important to note the box in the lower left corner of the windowsticker. These numbers represent the range of fuel economy expected onthe vehicl
permitted to intentionally remove an emission control device or preventit from working. Information about your vehicle’s emission system is onthe Vehi
condition. To ready the on-board diagnostics system for I/M testing, aminimum of 30 minutes of city and highway driving is necessary asdescribed below
4. Check the fluid level in thereservoir. It should be between theMIN and MAX lines. Do not addfluid if the level is in this range.5. If the fluid is
working properly, i.e., if the transmission slips or shifts slowly or if younotice some sign of fluid leakage.Automatic transmission fluid expands whe
The transmission fluid should be inthis range if at normal operatingtemperature (66°C-77°C[150°F-170°F]).The transmission fluid should be inthis range
AIR FILTER MAINTENANCERefer to the scheduled maintenance guide for the appropriate intervalsfor changing the air filter element.When changing the air
Traffic (if equipped): Allows you to hear traffic broadcasts. With thefeature ON, press SEEK or SCAN to find a station broadcasting a trafficreport (i
3. Install a new air filter elementinto the tray assembly.4. Return air filter tray to originalposition by pressing firmly on thehandle until all rear
REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to line onreservoi
Fluid Ford PartNameApplication CapacityFront axlelubricantMotorcraft SAE75W-90 FuelEfficient HighPerformanceSynthetic RearAxle Lubricant4x4 vehicles 3
2Indicates only approximate dry-fill capacity. Some applications may varybased on cooler size and if equipped with an in-tank cooler. The amountof tra
ItemFord partnameFord partnumberFordspecificationDriveshaft, slipspline, doubleCardan jointcenter ballPremium LongLife GreaseXG-1-K orXG-1-C orXG-1-TE
ItemFord partnameFord partnumberFordspecificationFront axle(4X4)Motorcraft SAE75W-90 FuelEfficient HighPerformanceSynthetic RearAxle LubeXY-75W90–QFEH
ENGINE DATAEngine 5.4L V8 engineCubic inches 330Required fuel 87 octaneFiring order 1-3-7-2-6-5-4-8Ignition system Coil on plugSpark plug gap 0.040–0.
14REVIEW COPY2005 Expedition (exd), Owners Guide (post-2002-fmt) (own2002),Market: USA_English (fus)Maintenance and Specifications357
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford
10. REPEAT: Press to repeat thecurrent CD/MP3 track.11. SHUFFLE: Press play theCD/MP3 tracks on the current discin random order.12. FOLDER: Press to a
Interior styleElectrochromatic compass/temperature interior mirrorsFloor matsLeather wrapped steering wheelsScuff platesLifestyleBike racksCargo organ
• To avoid interference with other vehicle functions, such as anti-lockbraking systems, amateur radio users who install radios and antennasonto their
AABS (see Brakes) ...259Accessory delay ...121Air bag supplementalrestraint system ...189–190, 194and chil
wiper blades ...317Climate control (see Airconditioning or Heating) ...96Clock adjust6-CD in dash ...
recommendations ...326refill capacities ...351specifications ...353, 356Exhaust fumes ...
lighting up panel andinterior ...104JJack ...220positioning ...
Parts (see Motorcraft parts) ...350Pedals (see Power adjustablefoot pedals) ...123Power adjustable foot pedals ...123Powe
TTire Pressure MonitoringSystem (TPMS)Driving ...282Maintenance andSpecifications ...236Roads
368
20. Load: Press to load a CD. Pressand hold to load up to six discs.21. CD: Press to enter CD mode.CD units are designed to play commercially pressed
REAR SEAT RADIO CONTROLS (IF EQUIPPED)If your vehicle is equipped with afront row console, then it is alsoequipped with rear seat radiocontrols.If you
To activate Dual Play mode (rearseat passengers listen to a differentplaying media than the front seatpassengers):• Press the speaker/headphonecontrol
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
Turning the rear speakers on and offPress the headphone/speakercontrol to turn the rear speakers on(Single Play mode) or off (Dual Playmode).Using hea
Memory preset controlPush the MEMORY/MEM controlsuccessively to allow rear seatpassengers to scroll through the 6memory presets in AM, FM1 orFM2.Push
RADIO FREQUENCIESAM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsComm
Don’t:• Expose discs to direct sunlight or heat sources for extended periodsof time.• Insert more than one disc into each slot of the CD changer magaz
DVD player controls1. MAIN control• NEXT — Press to access the next track on the CD, the next chapteron the DVD, or to go up in cursor mode.• PREV — P
7. Auxiliary jacksInsert lines for standard video game players.8. STOP/EJECT controlPress once to stop DVD play. Press again to eject the DVD.9. DISPL
• Press the FWD control to movethe cursor right one positionNext/Previous controlThe NEXT (up) and PREV (down)controls allow you to access thenext or
Slow play modeTo enter slow play mode, press thePLAY/PAUSE control. Once thesystem is in pause mode, press theFWD or REV control for slow motion playb
Remote control1. REWIND controlPress to reverse the direction of the DVD movie.2. FAST FORWARD controlPress to advance the direction of the DVD movie.
In stop mode, press to change to a different playing media (e.g. AM, FM,CD...)8. VOLUME controlPress to increase (+) or decrease (-) volume level.Batt
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
To install the batteries, lightly pressdown on the top of the left earpieceand slide the cover off.When replacing the batteries, usetwo new batteries
Liquid Crystal Display (LCD) flip-down screenThe screen rotates down to view and into the housing to store when notin use. Be sure the screen is latch
• When the temperature of the DVD player becomes too hot, the hightemperature sensor circuit stops machine operation. DVD/CD HOT willilluminate in the
Inserting a CD/DVD into the DVD player automatically turns the powerON and playback should begin.The counter is automatically reset to 0:00:00.Removin
1. CD track2. DVD chapter3. SYSTEM COUNTER — displays current viewing time of desired media.(HOURS:MINUTES:SECONDS)4. DVD/ CD STATUS (PLAY/FF/REW/PAUS
Whenever a warning is received, the radio volume will be loweredto a volume that will allow the tones to be heard. The radiovolume will return to the
moisture condensation occurs, do not insert a CD or DVD into theplayer. If one is already in the player, remove it. Turn the DVD player ONto dry the m
Safety informationPlease read and follow all stated safety precautions. Failure to doso may increase your risk of collision and personal injury.Ford M
• For road safety reasons, the driver should program the system onlywhen the vehicle is stationary. Certain functions will therefore notoperate while
location as home. Pressing the home key after the home location hasbeen set will calculate a route to that set home location.2. Eject: Press this cont
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
When in RSC mode, Dual Play mode can be enabled and disabled by theRSC, or by pressing Preset 2 and 4 simultaneously on the Navigationradio system. Th
14. MENU: The MENU controlworks in both the audio andnavigation mode. Press to accessvarious menus in both modes.15. HERE: The HERE control worksin th
3. Press the memory presets tochoose the desired disc in the CDDJ.Note: Navigation CD’s are not operational in the CD DJ.To use the Navigation system:
Volume/power controlPress the control to turn theaudio/navigation system on or off.Turn the control to raise or lower volume. The levels will be displ
5. Use the cursor control to increaseor decrease the levels. The higherthe level selected, the greater thecompensation. The levels will beshown in the
CD selectTo begin CD play (if a CD is alreadyloaded), press the CD control. Thefirst track of the disc will beginplaying. After that, CD play willbegi
4. Use the cursor control to increaseor lower the bass and treble levelsor to adjust the sound between thefront and rear or between the leftand right
Rewind/fast forwardPress theand controlsto fast forward or rewind a CDtrack.Seek functionThe SEEK control works in allmodes.Seek in radio mode• Presst
Setting memory preset stations1. Select the frequency band with the AM/FM select control.2. Select a station. Refer to Tune adjust or Seek function fo
Tune adjustThe tune feature works in radiomode.• Select the TUNE soft key.• Press SEEK to go upordown the frequency bandmanually.Stereo indicatorWhene
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental restraint
Select the TRAF soft key to select traffic information broadcast fromcertain stations which will automatically interrupt radio or CD playbackat a pres
Press the CD control until DVDappears in the display.(EJECT) — Press to stop DVD and eject the DVD disc.(PLAY) / II (PAUSE) — Press to play/pause the
To access the CD DJ:Slide the door to access the CD DJmagazine.Pressto eject the magazine.1. Pull the lever to remove a CDtray from the magazine.2. In
3. Insert each CD tray, with the discloaded, all the way into the CDmagazine.4. Insert the CD magazine into theCD DJ.5. Slide the door to the left to
Ensure that the disc holder isevenly inserted and at the samelevel as the magazine (A). The unitwill not operate if the disc holder isnot inserted at
Rewind/fast forward featureWhen in CD DJ mode, press andhold theor control tosearch forward or in reverse on thecurrent disc.Scan featureWhen in CD DJ
Rear seat controls (RSC)Your vehicle is equipped with rear seat controls, which allow the rearseat passengers to operate and listen to a different pla
Please drive safelyThis screen may appear on yourVNR display. Press the soft key nextto the display to select the desiredlanguage. Press the control n
Limited GPS receptionSystem performance may be adversely affected if GPS reception isinterrupted or interference occurs over a distance of several mil
Map display informationWhen using the navigation system,the map display screen will appearto guide you to your location. Onthe screen, you are able to
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
Address/IntersectionUse the soft keys to selectAddress/Intersection from theDestination Entry menu. The nexttwo options available are:• Town/City Name
• Within a Town/City – Lists entries for a specific city in alphabeticalorder.Certain categories may not be available in some areas and POIs may notal
• To move back to previously selected characters, press DELETE.List – Your VNR system shows a list of town/cities, streets or points ofinterest and a
This screen will appear for a fewseconds while the navigation systemis calculating your route.Please proceedOnce the route is calculated, ’PleaseProce
Guide displayOnce your vehicle is moving alongthe highlighted route, the Guidedisplay screen will automaticallyappear. This screen shows your nextturn
ArrivalWhen you approach yourdestination, the destination indicatorwill appear on the map displayscreen as a circular icon. When youarrive, the name a
6. Press the EDIT soft key to editthe current entry.• Use the cursor control to select aletter.• Push the control to add a letterto the name. If you m
Detours, route interruptions and changesIf need be, your navigation systemcan easily and quickly find the mostefficient detour around roadconstruction
• Resume route - The navigationsystem displays the Select RouteCriteria screen. Refer toSelecting Route Criteria earlierin this chapter.• Cancel route
• UNITS — Press to select from miles or kilometers. When Km areselected, it will affect the map and the fuel economy screen.Display optionsUse this fe
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
2. Press the ADJUST control toselect the hours or minutes to set.3. Use the cursor control to increaseor decrease the hours or minutes.4. Press DONE t
Map coverageThe following map data CDs are available for the navigation system:• CD1: California/Nevada/Hawaii• CD2: Northwest/Southwest• CD3: North C
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
• Under normal weather conditions, do not leave the air flow selector inMAX A/C or OFF when the vehicle is parked. This allows the vehicleto “breathe”
1. A/C control: Uses outside air tocool the vehicle. Press to turn on/offin all modes exceptor .2. Recirculation control: Used tomanually enable or di
12. AUTO: Press AUTO and thenselect the desired temperature. Thesystem will automatically determinefan speed, airflow location and outside or recircul
DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEMWITH HEATED AND COOLED SEATS (IF EQUIPPED)1. A/C control: Press to turn onand manually control the air
fourth time to disengage the feature (all lights will be off). Note: Thepassenger heated seat will turn off automatically after 15 minutes of use.5.R(
Press and hold AUTO for about two seconds to toggle between singlezone and dual zone temperature control.12. Driver heated seat: Press to turn on the
OPERATING TIPS• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
Commentaires sur ces manuels