Ford 2005 Excursion v.3 Manuel d'utilisateur

Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 13Entertainment Systems 17AM/FM stereo cassette with CD 17AM/FM stereo with in-

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa

Adjusting the front power seat (if equipped)The control is located on the outboard side of the seat cushion.Press to raise or lower the frontportion o

The system will not automatically shutoff unless control is pushed todeactivate. If system is not manually terminated at last use, then systemwill rem

REAR SEATSHead restraintsTo properly adjust your head restraints, lift the head restraint so that itis located directly behind your head or as close t

2. Lift seat cushion up and rotateforward.3. The headrest must be removed inorder to fold the seatback down.Remove 2nd row seat headrest bypushing in

5. Lift the lower seat control andflip the seatback down.6. For bench seats only, lift up flapon seatback to release closeoutpanel.7. For bench seats

1. For bench seats, rotate the closeout panel onto the seatback andsecure with the retaining flap.2. Lift the lower seat control.3. Pull up on the sea

Accessing the third row seatYour vehicle is equipped with an easy entry second row seat featurewhich allows ready access to the third row seat. You ma

Removing the third row seatFrom the rear of the vehicle, with the liftgate window and cargo doorsopen:1. Pull the seat release lever locatedon the low

3. Verify that the safety belts can move freely on either side of the seat.4. Lift the lever and pull up the seatback to drive position.SAFETY RESTRAI

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.Safety belts and seats can becom

Check fuel cap (if equipped):Illuminates when the fuel cap maynot be properly installed. Continueddriving with this light on may causethe Service engi

or more, the combination safety belts will lock to help reduce forwardmovement of the driver and passengers.Automatic locking modeWhen to use the auto

How to disengage the automatic locking modeDisconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic l

Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could re

• 2nd row center seating position (if equipped)The lap belt will not adjust automatically. To fasten, grasp the tongue,and with a continuous motion, p

If... Then...The driver’s safety belt is notbuckled before the vehicle hasreached at least 3 mph (5 km/h)and 1-2 minutes have elapsedsince the ignitio

Reasons given... Consider...“I was in a hurry” Prime time for an accident.BeltMinder娂 reminds us to take a fewseconds to buckle up.“Safety belts don’t

One time disableAny time the safety belt is buckled and then unbuckled during anignition ON cycle, the BeltMinder娂 will be disabled for that ignitionc

• This will enable the BeltMinder娂 feature if it is currently disabled. Asconfirmation, the safety belt warning light will flash 4 times persecond for

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or other injuries.To properly position yourself

Airbag readiness: If this light failsto illuminate when ignition is turnedto ON, continues to flash or remainson, have the system servicedimmediately

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.Alwa

Booster seats should be used until you can answer YES to ALL of thesequestions:• Can the child sit all the way backagainst the vehicle seat back withk

The shoulder belt should cross the chest, resting snugly on the center ofthe shoulder. The lap belt should rest low and snug across the hips,never up

• Review and follow the informationpresented in the airbagsupplemental restraint system(SRS) section in this chapter.• Use the correct safety belt buc

Installing child safety seats with combination lap and shoulderbeltsAirbags can kill or injure a child in a child seat. NEVER place arear-facing child

3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat.

Securilock娂 Anti-theft system:Flashes when the Securilock娂Passive Anti-theft System has beenactivated.Door ajar: Illuminates when theignition is in th

• Second row 60/40 bench seat• Second row bucket seatsAttach the tether strap only to the appropriate tether anchor asshown. The tether strap may not

• Second row 60/40 bench seatNote: In the right seating position, use either tether anchor.• Second row bucket seatsNote: For each seat, use either te

• Third row• The anchors are on the back of the seat frame.4. Clip the tether strap hook to theanchor.If the tether strap is clippedincorrectly, the c

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary.

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

government test course. For example, a tire graded 150 would wear oneand one-half (1 1/2) times as well on the government course as a tiregraded 100.

• Tire Identification Number (TIN): A number on the sidewall ofeach tire providing information about the tire brand andmanufacturing plant, tire size

Every day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires and adjust ifrequired.A

Always inflate your tires to the Ford recommended inflation pressureeven if it is less than the maximum inflation pressure information foundon the tir

Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,

5. Repeat this procedure for each tire, including the spare.Note: Some spare tires require higher inflation pressure than the othertires. Check the Sa

Only use replacement tires and wheels that are the same sizeand type (such as P-metric versus LT-metric or all-season versusall-terrain) as those orig

different in brand, size or appearance from the road tires and wheels. Ifyou have a dissimilar spare tire/wheel, then it is intended for temporaryuse

If the vehicle slips off the jack, you or someone else could beseriously injured.1. Park on a level surface, activatehazard flashers and set the parki

When one of the rear wheels is off the ground, the transmissionalone will not prevent the vehicle from moving or slipping off thejack, even if the tra

• Front driver side (4x4)Make sure the jack fits into thenotched area on the differentialhousing.• Rear8. Turn the jack handle clockwiseuntil the whee

11. Lower the wheel by turning the jack handle counterclockwise.12. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lu

When a wheel is installed, always remove any corrosion, dirt orforeign materials present on the mounting surfaces of the wheelor the surface of the wh

3. 65: Indicates the aspect ratio which gives the tire’s ratio of height towidth.4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or ri

8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n

Engine oil pressure gauge:Indicates engine oil pressure. Theneedle should stay in the normaloperating range (between “L” and“H”). If the needle falls

Label which is located on the B-Pillar or the edge of the driver’s door.The cold inflation pressure should never be set lower than therecommended pres

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE CAREImproper or inadequate vehicle maintenance can also cause tires to wearabnormally. Here are some of the important maintenance items:Tire wear

Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t

Tire rotationRotating your tires at the recommended interval (as indicated in thescheduled maintenance information that comes with your vehicle) willh

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can

tires and chains. If you need to use chains, it is recommended that steelwheels (of the same size and specifications) be used, as chains may chipalumi

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei

Yellow area (warning) — thetransmission fluid is higher thannormal operating temperature. Thiscan be caused by special operationconditions (i.e. towin

GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).

mandatory options, no cargo (internal or external), a tongue load of10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), a

6. If your vehicle will be towing a trailer, load from your trailer will betransferred to your vehicle. Consult this manual to determine how thisreduc

Special loading instructions for owners of pickup trucks andutility-type vehiclesFor important information regarding safe operation of this typeof veh

4x4 w/automatic transmissionEngine Rear axle ratio MaximumGCWR-kg (lb.)Maximumtrailerweight-kg (lb.)5.4L 4.10 14500 (6350) 7100 (3220)6.8L 3.73 17000

Note: Adjusting an equalizing hitch so the rear bumper of the vehicle ishigher than it was unloaded will defeat the function of the loadequalizing hit

Driving while you towWhen towing a trailer:• Turn off the speed control. The speed control may shut offautomatically when you are towing on long, stee

Launching or retrieving a boatWhen backing down a ramp during boat launching or retrieval,• Do not allow the static water level to rise above the bott

STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo

Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,

PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED)1. Power/volume: Press to turnON/OFF; turn to increase/decreasevolume.2. SCAN: Press to hear a br

• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).• Turn the key to 4 (ON) withoutturning the key to 5 (START).Make sure the

• If the driver’s safety belt is fastened, the light may not illuminate.Starting the engine1. Turn the key to 4 (ON) withoutturning the key to 5 (STAR

Guarding against exhaust fumesCarbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects.If you smell exhaust fumes i

Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake

Pull the right side of the releaselever to release the parking brake;the release lever pulls at an angletoward the driver’s door. To preventthe pedal

• loose or worn steering components• improper steering alignmentIf any steering components are serviced or replaced, install newfasteners (many are co

AUTOMATIC TRANSMISSION OPERATIONBrake-shift interlockThis vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever fr

Understanding the gearshift positions of the 4–speed automatictransmission (if equipped-gasoline engines only)This vehicle is equipped with an adaptiv

N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.(O

• Selecting 2 (Second) at higher speeds will cause the transmission todownshift to second gear at the appropriate vehicle speed.1 (First)• Provides ma

not be inserted into the CD player. The label may peel and causethe CD to become jammed. It is recommended that homemadeCDs be identified with permane

To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)Always set the parking brake full

the vehicle speed when descending a hill, without the accelerator pedalbeing pressed. The amount of downshift braking provided will vary basedupon the

Do not rock the vehicle for more than a minute or damage to thetransmission and tires may occur, or the engine may overheat.REVERSE SENSING SYSTEM (IF

The RSS detects obstacles up to sixfeet (two meters.) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to t

FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED)For important information regarding safe operation of this typeof vehicle, see Preparing to drive your v

• auto-manual hub locks can bemanually overridden by rotatingthe hub lock control from AUTOto LOCK if desired.• automatic operation of thehub locks is

2H (2WD High) – For general on-road driving. Sends power to the rearwheels only.4H (4WD High) – For winter and off-road conditions. Sends power tofron

Shifting from 4x4 HIGH (4WD High) to 4x4 LOW (4WD Low)1. Bring the vehicle to either a complete stop or vehicle speed below3 mph (5 km/h).2. Depress t

How your vehicle differs from other vehiclesTruck and utility vehicles can differ from some other vehicles. Yourvehicle may be higher to allow it to t

sideways out of control or roll over. Remember, your safety and thesafety of others should be your primary concern.Vehicles with a higher center of gr

to decrease minutes or TUNE to increase minutes. If your vehiclehas a stand alone clock this control will not function.10. BAL (Balance): Press BAL;th

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.

Power is supplied to all four wheelsthrough a transfer case. On 4WDvehicles, the transfer case allowsyou to select 4WD when necessary.Information on t

Once through water, always try the brakes. Wet brakes do not stop thevehicle as effectively as dry brakes. Drying can be improved by movingyour vehicl

When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This r

faster, because as in other vehicles, braking occurs at all four wheels. Donot become overconfident as to road conditions.Make sure you allow sufficie

DRIVING THROUGH WATERIf driving through deep or standing water is unavoidable, proceed veryslowly especially when the depth is not known. Never drive

GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program

Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will

This switch is located in the frontpassenger’s footwell, behind the kickpanel access cover.To reset the switch:1. Turn the ignition OFF.2. Check the f

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

Seating and Safety Restraints 97Seating 97Safety restraints 108Airbags 118Child restraints 122Tires, Wheels and Loading 133Tire Information 135Tire In

15. SIDE 1–2: Works in tape modeonly. Press to play reverse side ofthe tape.16. FF (Fast Forward): In CDmode, press for a slow advance,press and hold

To remove a fuse use the fuse pullertool provided on the fuse panelcover.Always disconnect the battery before servicing high currentfuses.To reduce th

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description3 20A* Power point – 3rd row4 20A* Power point - I/P5 20A* Power point - ri

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description30 15A* Highbeam headlamps31 15A* Transmission range sensor (then tostarter

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description111 30A** 4WD/Shift on the fly112 30A** Left-hand power seats113 30A** Star

Do not attempt to push-start your vehicle. Automatictransmissions do not have push-start capability; doing so maydamage the catalytic converter.Prepar

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

21. SEEK: Press and releaseSEEK/ for previous/nextstrong station, selection or track.22. AM/FM: Press to selectAM/FM1/FM2 frequency band.PREMIUM IN-DA

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai

Board membershipThe Board consists of:• Three consumer representatives• An authorized dealer representativeConsumer candidates for Board membership ar

Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral

authorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of Canada participates in an impartialthird party

GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADABefore exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate.

Or call:For a free publication catalog, order toll free: 1-800-782-4356Monday-Friday 8:00 a.m. - 6:00 p.m. ESTHelm, Incorporated can also be reached b

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

3. Comp (Compression): In CD mode, press to adjust the soft and loudpassages together for a more consistent listening level. Press the COMPcontrol unt

racks, bumpers, side moldings, mirror housings or the windshield cowlarea. The paint sealant will “gray” or stain the parts over time.PAINT CHIPSYour

• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.• Cover the highlighted areas to prevent wa

special solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade and windshield from automated carwash facilities

• If a ring forms on the fabric after spot cleaning, clean the entire areaimmediately (but do not oversaturate) or the ring will set.• Do not use hous

Motorcraft Bug and Tar Remover (ZC-42)Motorcraft Car Care Kit (ZC-26)Motorcraft Car Wash (Canada only) (CXC-21)Motorcraft Custom Bright Metal Cleaner

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide sc

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT5.4L V8/6.8L V10 gasoline enginesRefer to the 6.0 Liter Power Stroke Direct Injection Turbo DieselOwne

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

3. Set the parking brake and ensure the gearshift is securely latched in P(Park).4. Open the hood. Protect yourself from engine heat.5. Locate and car

broadcasting a traffic report (if it is broadcasting RDS data). Trafficinformation is not available in most U.S. markets.FIND Program type: In FM mode

2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler cap

Ford production and aftermarket (Motorcraft) oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedtha

Note: Electrical or electronic accessories or components added tothe vehicle by the dealer or the owner may adversely affectbattery performance and du

5. Turn the A/C on and allow the engine to idle for at least one minute.6. Release the parking brake. With your foot on the brake pedal and withthe A/

• Freeze protection down to -34°F (-36°C).• Boiling protection up to 265°F (129°C).• Protection against rust and other forms of corrosion.• Enables ca

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur

coolant degas system with a pressurized cap, or if it is necessary toremove the coolant pressure relief cap on the radiator of a vehicle withan overfl

Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut

What you should know about fail-safe cooling (if equipped)If the engine coolant supply is depleted, this feature allows the vehicle tobe driven tempor

4. Check the coolant level and replenish if low.Never remove the coolant reservoir cap while the engine isrunning or hot.5. Re-start the engine and ta

14. Load: Press to load a CD.SELECT SLOT will appear in thedisplay. Select from 1–6 on thememory presets. MOVING TO # and then LOAD CD# will appear in

• Extinguish all smoking materialsand any open flames beforerefueling your vehicle.• Always turn off the vehicle beforerefueling.• Automotive fuels ca

RefuelingFuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others:• Read and follow all the instr

If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any

Do not be concerned if your engine sometimes knocks lightly. However, ifit knocks heavily under most driving conditions while you are using fuelwith t

Replace the fuel filter with an authorized Motorcraft part. Thecustomer warranty may be void for any damage to the fuel systemif an authorized Motorcr

• Have the vehicle loading and distribution the same every time.Your results will be most accurate if your filling method is consistent.Calculating fu

• Revving the engine before turning it off may reduce fuel economy.• Using the air conditioner or defroster may reduce fuel economy.• You may want to

• Four-wheel-drive operation (if equipped) is less fuel efficient thantwo-wheel-drive operation.• Close windows for high speed driving.EPA window stic

Exhaust leaks may result in entry of harmful and potentiallylethal fumes into the passenger compartment.Do not make any unauthorized changes to your v

soon light is on, refer to the description in the Warning lights andchimes section of the Instrument Cluster chapter. Your vehicle may notpass the I/M

5. Volume: Press + to increase and — to decrease volume levels. Fromthe rear seat controls, volume cannot be set higher than the front seatsetting.6.

6. Recheck the fluid level on the dipstick. Do not add fluid if the level isbetween the arrows in the FULL COLD range.7. If the fluid is low, add flui

6. Install the dipstick making sure it is fully seated in the filler tube.7. Remove the dipstick and inspect the fluid level. The fluid should be inth

Adjusting automatic transmission fluid levelsBefore adding any fluid, make sure the correct type is used. The type offluid used is normally indicated

Automatic transmission fluid filter (if equipped)The TorqShift automatictransmission is equipped with aserviceable external fluid filtermounted on the

Transfer case fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough fluid throughthe fil

Changing the air filter element1. Loosen the clamp that securesthe air filter element in place.2. Carefully separate the two halvesof the air filter h

MOTORCRAFT PART NUMBERSComponent 5.4L V8 engine 6.8L V10 engineAir filter element1FA-1634 FA-1634Fuel filter FG-986B FG-986BOil filter FL-820-S FL-820

REFILL CAPACITIESFluidFord PartNameApplication CapacityFront axle Motorcraft SAE80W-90Premium RearAxle Lubricant4X4 vehicles 3.6 pints (1.8L)Rear axle

FluidFord PartNameApplication CapacityFuel tank N/A All 44.0 gallons(166.6L)Power steeringfluidMotorcraftMERCON威 ATFAll Fill to FULLCOLD range ondipst

3Add the coolant type originally equipped in your vehicle.4If equipped with auxiliary rear heater, add an additional 1.4 L (1.5quarts).5Ensure the cor

CD/CD PLAYER CAREDo:• Handle discs by their edges only. Never touch the playing surface.• Inspect discs before playing. Clean only with an approved CD

LUBRICANT SPECIFICATIONSItemFord partname orequivalentFord partnumberFordspecificationSpindle bearingHighTemperature4X4 Front Axleand WheelBearing Gre

ItemFord partname orequivalentFord partnumberFordspecificationEngineoil-GasolineenginesMotorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcr

ItemFord partname orequivalentFord partnumberFordspecificationAutomatictransmissionTorqShift(5–speed)MotorcraftMERCON威 SPATF2XT-6–QSP WSS-M2C919–DMERC

ENGINE DATAEngine 5.4L V8 engine 6.8L V10 engineCubic inches 330 415Required fuel 87 octane 87 octaneFiring order 1-3-7-2-6-5-4-8 1-6-5-10-2-7-3-8-4-9

IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety ComplianceCertification

Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea

Transmission/Transaxle code designationsYou can find atransmission/transaxle code on theSafety Compliance CertificationLabel . The following table tel

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford

Interior styleElectrochromatic compass/temperature interior mirrorsFloor matsLeather wrapped steering wheelsLifestyleBike racksCargo organization and

• To avoid interference with other vehicle functions, such as anti-lockbraking systems, amateur radio users who install radios and antennasonto their

DVD player controls1. MAIN control• NEXT — Press to access the next track on the CD, the next chapteron the DVD, or to go up in cursor mode.• PREV — P

AAccessory delay ...66Air cleaner filter ...254–256Air conditioning ...45Airbag supplemental

wiper blades ...221Climate control (see Airconditioning or Heating) ...45, 47Clock adjust6-CD in dash ...

Fluid capacities ...257Foglamps ...50Four-Wheel Drive vehicles ...184description ...

positioning ...141storage ...141Jump-starting your vehicle ...203KKeyless entry syste

fluid, specifications ...260, 263Power Windows ...65Preparing to driveyour vehicle ...175RRa

tire grades ...136treadwear ...135, 152Towing ...163recreational

276

277

278

279

7. Auxiliary jacksInsert lines for standard video game players.8. STOP/EJECT controlPress once to stop DVD play. Press again to eject the DVD.9. DISPL

280

• Press the FWD control to movethe cursor right one positionNext/Previous controlThe NEXT (up) and PREV (down)controls allow you to access thenext or

Maintenance and Specifications 225Engine compartment 227Engine oil 228Battery 231Engine Coolant 233Fuel information 239Air filter(s) 255Part numbers 2

FWD or REV control for slow motion playback. Three different speedsare available depending on how long the control is held. Press thecontrol once for

2. FAST FORWARD controlPress to advance the direction of the DVD movie.3. PLAY/STOP controlPress to play or stop the DVD movie.4. SEEK controlPress to

Rear seat controlsThe rear seat controls allow the rearseat passengers to operate theradio, tape, CD, DVD or AUX (ifequipped).Adjusting the volume fro

• DVD/AUXDVD player / Auxiliary line input (if equipped)Memory preset controlIn radio mode, press the MEMORYcontrol successively to scrollthrough the

Using wired headphones/Personal Audio FeatureSingle play mode will allow allpassengers to listen to the samemedia source through all speakers.The Pers

Press the memory preset controls 2and 4 simultaneously to togglebetween single play and thePersonal Audio Feature.Wireless headphones (for DVD system

When not using the headphones,shut them off to preserve batterypower. The headphones willautomatically turn off after fiveminutes if they have not rec

Playback and format• The DVD player of your Rear Seat Entertainment DVD System canonly be used in the “playback” mode. (The DVD player does not offera

incompatibility, certain recordable and re-recordable compactdiscs may not function correctly when used in Ford DVD/CDplayers. Irregular shaped discs,

On-screen indicatorsEach time a control is pressed, the operational status of the DVD playeris shown on the screen. The following are some possible in

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

Do not expose the liquid crystal display (LCD) flip-down screento direct sunlight or intensive ultraviolet rays for extensiveperiods of time. Ultravio

• high humidity.• a dusty environment.• locations where strong magnetic fields are generated.Temperature extremesWhen the vehicle is parked under dire

HEATER ONLY SYSTEM (IF EQUIPPED)1. Fan speed adjustment: Controls the volume of air circulated in thevehicle.2. Temperature selection: Controls the te

3. Set the fan speed to the highest setting.4. Direct the outer instrument panel vents toward the side windows.To increase airflow to the outer instru

: Distributes outside air through the windshield defroster vents anddemister vents.Operating tips• To reduce fog build up on the windshield during hum

AUTOMATIC TEMPERATURE CONTROL SYSTEM (IF EQUIPPED)Press the AUTO and(floor/defrost) controls at the same time andhold for one second to switch between

6. (Floor): Distributes air through the floor vents.7.(Panel/floor): Distributes air through the instrument panel vents,floor vents and center console

• To improve the A/C cool down, drive with the windows slightly openfor 2–3 minutes after start up or until the vehicle has been “aired out.”For maxim

vehicle. If the main climate control system is in Max A/C mode (formanual controls) or in full cooling (for automatic controls) the auxiliarytemperatu

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

Foglamp control (if equipped)The headlamp control also operatesthe foglamps. The foglamps can beturned on only when the headlampcontrol is in the, orp

Flash to passPull toward you slightly to activateand release to deactivate.PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and

4. On the wall or screen you willobserve a light pattern with adistinct horizontal edge towards theright. If this edge is not at thehorizontal referen

INTERIOR LAMPSDome/Map lamps (if equipped)The map lamps and controls arelocated on the dome lamp. Press thecontrols on either side of each maplamp to

Rear dome lampThe dome lamp lights when:• any door is opened (and switch isin middle position).• the instrument panel dimmerswitch is held up until th

Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an

2. Remove the four screws from thetop and bottom front of theheadlamp assembly.3. Press the retaining clip at the topof the headlamp assembly whilepul

Replacing park/turn and sidemarker lamp bulbs1. Make sure that the headlamp control is in the OFF position and openthe hood.2. Remove the four screws

Replacing foglamp bulbs1. Make sure the headlamp switch isin the OFF position and then rotatethe foglamp bulb counterclockwiseand remove from foglamp

Replacing high-mount brakelamp bulbs1. Make sure the headlamp switch isin the OFF position and remove thetwo screws and then the lampassembly.2. Remov

systems. In order to properly diagnose and service your vehicle, FordMotor Company, Ford of Canada, and service and repair facilities mayaccess vehicl

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Changing the wiper blades1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas

TRANSMISSION CONTROLTow/Haul feature (5–speed automatic transmission) (if equipped)To activate, press the transmissioncontrol switch (TCS) located on

Forward storage bin (if equipped)Press the release control to openthe storage compartment. The doorwill open slightly and can be movedto full open.The

AUXILIARY POWER POINT (12VDC)Power outlets are designed for accessory plugs only. Do not hangany type of accessory or accessory bracket from the plug.

• Located in the left side storagecompartment in the third rowseating position.• Located on the right trim panel inthe rear cargo area.POWER WINDOWSDo

One touch downAllows the driver’s window to openfully without holding the controldown. Press completely down onAUTO and release quickly. Pressagain to

Press the control located on thebottom of the mirror to turn themirror on or off. The mirror willautomatically return to the normalstate whenever the

Type BThe spotter mirror, below the mainmirror, is not heated and must beadjusted manually.Do not remove ice from the mirrors with a scraper or attemp

Clearance lamps (if equipped)Illuminates when the headlamps orparking lamps are switched on.This provides additional visibility ofyour vehicle to othe

Notice to owners of pickup trucks and utility type vehiclesUtility vehicles have a significantly higher rollover rate thanother types of vehicles.Befo

POWER ADJUSTABLE FOOT PEDALSThe accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park

3. Press the SET ACCEL controland release it.4. Take your foot off the acceleratorpedal.5. The indicatorlight on theinstrument cluster will turn on.No

Reducing speed while using speed controlThere are two ways to reduce a setspeed:• Press and hold the COASTcontrol until you get to thedesired speed, t

STEERING WHEEL CONTROLS (IF EQUIPPED)These controls allow you to operate some radio and climate controlfeatures.Radio control features• Press MODE to

Selectable featuresEnglish/metric displayPress this control to change the tripcomputer display between metricand English units.Mode controlEach press

2. Press the E/M and MODEcontrols simultaneously. The displaywill illuminate the “AVG” indicator.While the indicator is lit, releaseboth controls to r

The compass heading is displayed in average fuel economy modes, fuelrange modes and temperature modes.The compass reading may be affected when you dri

1. Locate the trip computer located in the overhead console.2. Start the vehicle.3. Press and hold both tripcomputer controls. Afterapproximately eigh

ProgrammingDo not program HomeLink威 with the vehicle parked in the garage.Note: Your vehicle may require the ignition switch to be turned to theACC po

Note: If the indicator light blinks rapidly for two seconds and then turnsto a continuous red, proceed with Steps 6 through 8 to completeprogramming o

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet

CENTER CONSOLEYour vehicle may be equipped with a variety of console features. Theseinclude:• Utility compartment• Coin holder slots• Pen holderUse on

CARGO NET (IF EQUIPPED)The cargo net secures lightweightobjects in the cargo area. Attach thenet to the anchors provided.This net is not designed tore

The cargo doors and liftgate should be closed before driving yourvehicle. Make sure the liftgate and/or the cargo doors are closedto prevent exhaust f

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.

KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w

Childproof door locks• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the

• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta key.• activate the personal alarm.If there are problems with the remote

The UNLOCK feature will work again after:• a door has become ajar,• the ignition is turned to the 4 (ON) position,• unlocking the vehicle using the ke

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery. Note: Please refer to local r

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

To reprogram the remote entrytransmitters:1. Ensure the vehicle iselectronically unlocked.2. Put the key in the ignition.3. Turn the key from the 2 (L

The inside lights will not turn off if:• they have been turned on with the dimmer control, or• any door or the liftgate is open.The battery saver will

3. Press and hold the 1 • 2 for two seconds. This must be done withinfive seconds of completing Step 2.Your personal code is now erased and only the f

• the brake is pressed before reaching 5 mph (8 km/h), and• the vehicle is traveling more than 5 mph (8 km/h).To deactivate/reactivate the autolock fe

SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEMSecuriLock娂 passive anti-theft system is an engine immobilizationsystem. This system is designed to help prevent

Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 3(OFF) position.TheTHEFTindicator will flashevery two seconds when

1. Insert a previously programmedcoded key into the ignition.2. Turn the ignition from the 3 (OFF) position to the 4 (ON) position.Keep the ignition i

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

60/40 split bench seat (if equipped)• Lift the release bar to move theseat forward or backward. Ensurethe seat is relatched into place.• Pull the seat

Memory seats and adjustable pedals (if equipped)This system allows automaticpositioning of the driver seat andadjustable pedals to twoprogrammable pos