Introduction 4Instrument Cluster 12Warning and control lights 12Gauges 15Entertainment Systems 18AM/FM stereo 18AM/FM stereo cassette 19AM/FM stereo w
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
• Fifteen passenger wagonrepresents LATCH anchors.represents tether strap anchors.Never attach two LATCH child safety seats to the same anchor. Ina cr
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
VEHICLE CHARACTERISTICSHow your vehicle differs from other vehiclesSUV and trucks can differ fromsome other vehicles in a fewnoticeable ways. Your veh
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
tread grooves. Check for holes or cuts that may permit air leakage fromthe tire and make necessary repairs.Also inspect the tire sidewalls for cuts, b
pressure should never be set lower than the recommended pressure onthe tire label or certification label.When weather temperature changes occur, tire
Tire inflation informationAll tires with Steel Carcass Plies (if equipped):This type of tire utilizes steel cords in the sidewalls. As such, theycanno
Only use replacement tires and wheels that are the same sizeand type (such as P-metric versus LT-metric or all-season versusall-terrain) as those orig
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
different in brand, size or appearance from the road tires and wheels. Ifyou have a dissimilar spare tire/wheel, then it is intended for temporaryuse
To remove the spare tire:1. Open the rear doors and removethe thumb screw and anti-theftbracket. If finger pressure will notremove the thumb screw, us
4. Apply the parking brake and turnthe engine off.5. Block the wheel that is diagonallyopposite the tire you are changing.On E-450 vehicles, the parki
• the jack is located in the rearright-hand side of the cargo area.7. Use the tapered end of the lug nut wrench to unscrew wheelornaments attached by
• Never use the front or reardifferential as a jacking point.Rear axle jacking points - Allmodels except E-350 Dual RearWheel (DRW) and E-450:Rear axl
Front axle jacking points:Place the jack under the pin on thefront surface of the front axle.Do not place the jack under oron the steering linkage.• R
• 8-lug wheelNever use wheels or lugnuts different than theoriginal equipment as this coulddamage the wheel or mountingsystem. This damage could allow
move. Loosen and retighten, if necessary. Failure to properly stow thespare tire may result in failure of the winch cable and loss of the tire.5. Repe
When a wheel is installed, always remove any corrosion, dirt orforeign materials present on the mounting surfaces of the wheelor the surface of the fr
4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa
8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n
which is located on the B-Pillar or the edge of the driver’s door. The coldinflation pressure should never be set lower than the recommendedpressure o
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
the road in adverse (wet, snowy, etc.) conditions. Visually check yourtires for uneven wear, looking for high and low areas or unusuallysmooth areas.
• Avoid potholes and objects on the road• Do not run over curbs or hit the tire against a curb when parkingIf your vehicle is stuck in snow, mud, sand
help your tires wear more evenly, providing better tire performance andlonger tire life. Unless otherwise specified, rotate the tires approximatelyeve
Sometimes irregular tire wear can be corrected by rotating the tires.Note: If your tires show uneven wear ask a qualified technician at aFord or Linco
capability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design performance. Before loadingyour vehi
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei
Electronic throttle control (ifequipped): Illuminates when theengine has defaulted to a’limp-home’ operation. Report thefault to a dealer at the earli
GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).
mandatory options, no cargo (internal or external), a tongue load of10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), a
6. If your vehicle will be towing a trailer, load from your trailer will betransferred to your vehicle. Consult this manual to determine how thisreduc
Special loading instructions for owners of pickup trucks andutility-type vehiclesFor important information regarding safe operation of this typeof veh
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoaded TrailerWeight - lb. (kg)Maximumfrontal area o
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoaded TrailerWeight - lb. (kg)Maximumfrontal area o
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoaded TrailerWeight - lb. (kg)Maximumfrontal area o
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoaded TrailerWeight - lb. (kg)Maximumfrontal area o
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoaded TrailerWeight - lb. (kg)Maximumfrontal area o
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoaded TrailerWeight - lb. (kg)Maximumfrontal area o
immediately. A chime will also sound when a malfunction in thesupplemental restraint system has been detected.Safety belt: Reminds you to fastenyour s
GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoaded TrailerWeight - lb. (kg)Maximumfrontal area o
Towing a trailer places an additional load on your vehicle’s engine,transmission, axle, brakes, tires and suspension. Inspect thesecomponents carefull
Trailer lampsTrailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working.
• Allow more distance for stopping with a trailer attached.• The trailer tongue weight should be 10–15% of the loaded trailerweight.• If you will be t
RECREATIONAL TOWING (ALL WHEELS ON THE GROUND)An example of recreational towing would be towing your vehicle on atrip behind a motorhome. Follow these
STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).• Turn the key to 4 (ON) withoutturning the key to 5 (START).Make sure the
Starting the engine1. Turn the key to 4 (ON) withoutturning the key to 5 (START).2. Turn the key to 5 (START), thenrelease the key as soon as theengin
BRAKESOccasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-o
Transmission Tow/Haul light(TCIL) (5.4L and 6.8L gasolineengines only): Illuminates whenthe Tow/Haul feature of thetransmission has been turned on,ref
Parking brakeTo set the parking brake (1), pressthe parking brake pedal down untilthe pedal stops.To release, pull the lever (2).Always set the parkin
A high crown in the road or high crosswinds may also make the steeringseem to wander/pull.TRACTION-LOK AXLE (IF EQUIPPED)This axle provides added trac
shift rearward. As a result, the van has less resistance to rollover andhandles differently from other commonly driven passenger vehicles,making it mo
• If the vehicle goes from one type of surface to another (i.e., fromconcrete to gravel) there will be a change in the way the vehicleresponds to a ma
Understanding the gearshift positions of the 4–speed automatictransmissionThis vehicle is equipped with an adaptive Transmission Shift Strategy.Adapti
N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.(O
• Selecting 2 (Second) at higher speeds will cause the transmission todownshift to second gear at the appropriate vehicle speed.1 (First)• Provides ma
To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)Always set the parking brake full
transmission is in the D (Overdrive) position; this engine braking willslow the vehicle and assist the driver in controlling the vehicle whendescendin
Understanding the shift positions of the 5–speed automatictransmission (if equipped - diesel engines only)P (Park)This position locks the transmission
Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature, the needle will be inthe normal range (between “
D (Drive) without OverdriveD (Drive) without Overdrive can beactivated by pressing thetransmission control switch (TCS)on the end of the gearshift lev
If your vehicle goes off the edge of the pavement• If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ea
A more complete description of PTO operation is discussed in the FordTruck Body Builders Layout Book, found atwww.fleet.ford.com/truckbbas.DRIVING THR
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.Motorhome customers in the U.S and Canada should contact1–800–444–3311.If you n
Except for commercial strippedchassis vehicles, this switch islocated in the front passenger’sfootwell, by the kick panel.2005 Econoline (eco)Owners G
On commercial stripped chassisvehicles, this switch is located on abracket above the brake pedal.To reset the switch:1. Turn the ignition OFF.2. Check
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment Fuse PanelDescription1 5A 4–Wheel Anti–lock Brake System(4WABS) m
Fuse/RelayLocationFuse AmpRatingPassenger Compartment Fuse PanelDescription9 5A Wiper control module10 20A Main light switch, Park lamps, Licenselamp
Engine oil pressure gauge:Indicates engine oil pressure. Theneedle should stay in the normaloperating range (between “L” and“H”). If the needle falls
Fuse/RelayLocationFuse AmpRatingPassenger Compartment Fuse PanelDescription34 — Not used35 — Not used36 5A Instrument illumination37 — Not used38 — No
The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description1 — Powertrain Control Module (PCM) diod
Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description15 30A** Main light switch16 — Not used17 50A** Blower motor relay (blower motor)18
Relay modulesInstrument panel relay moduleThe instrument panel relay module is located behind the radio in thecenter of the instrument panel. Have a c
• Diesel engine: passenger side of the engine compartment behind thepower distribution box.Have a certified technician or your dealer service this mod
4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level.5. Tu
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
AM/FM STEREO (IF EQUIPPED)1. Seek: Press/ to find thenext listenable station down/up thefrequency band.2. Tune: Press/ to manuallyadjust the radio fre
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caAway
replacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure is not required prior to enforcing statecreated righ
The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedu
from Ford and Lincoln Mercury dealership management, recognized fortheir business leadership qualities.What the Board needsTo have your case reviewed
Making a decisionBoard members review all available information related to eachcomplaint, including oral presentations, and arrive at a fair and impar
In the CAMVAP program, impartial third-party arbitrators conducthearings at mutually convenient times and places in an informalenvironment. These impa
The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emission control system and may causeengine knock
Obtaining a French owner’s guideFrench Owner’s Guides can be obtained from your dealer or by writing toFord Motor Company of Canada, Limited, Service
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
6. Tone: Press TONE until thedesired level — Bass, Treble, Fadeappears on the display. Turn thevolume control to raise/lower thelevels, or to move the
racks, bumpers, side moldings, mirror housings or the windshield cowlarea. The paint sealant will “gray” or stain the parts over time.• Do not allow p
• Do not spray a hot engine with cold water to avoid cracking theengine block or other engine components.• Spray Motorcraft Engine Shampoo and Degreas
• Do not use abrasives, as they may cause scratches.• Do not use fuel, kerosene, or paint thinner to clean any parts.• Wiper blades can be cleaned wit
Do not use cleaning solvents, bleach or dye on the vehicle’sseatbelts, as these actions may weaken the belt webbing.LEATHER SEATS (IF EQUIPPED)Your le
Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A)Motorcraft Detail Wash (ZC-3–A)Motorcraft Dusting Cloth (ZC-24)Motorcraft Engine Sham
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide sc
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENTEngine compartment component locationsRefer to the 6.0 Liter Power Stroke Direct Injection Turbo Diese
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clean. Insertthe indicator fully, then remove itagain.•
Seating and Safety Restraints 66Seating 66Safety restraints 72Airbags 82Child restraints 86Tires, Wheels and Loading 101Tire Information 104Tire Infla
2. Fade: Press to shift sound to therear/front speakers.3. CLK: To set the hour, press andhold CLK. Then press SEEK todecreaseor increase thehours.To
Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t
Change your engine oil and filter according to the appropriate schedulelisted in scheduled maintenance information.Ford production and aftermarket (Mo
When the battery is disconnected or a new battery installed, thetransmission must learn its adaptive strategy. As a result of this, thetransmission ma
2. Put the gearshift in P (Park), turn off all accessories and start theengine.3. Run the engine until it reaches normal operating temperature.4. Allo
Your vehicle was factory-filled with a 50/50 engine coolant and waterconcentration. If the concentration of coolant falls below 40% or above60%, the e
Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur
coolant degas system with a pressurized cap, or if it is necessary toremove the coolant pressure relief cap on the radiator of a vehicle withan overfl
Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut
What you should know about fail-safe cooling (if equipped)If the engine coolant supply is depleted, this feature allows the vehicle tobe driven tempor
Never remove the coolant reservoir cap while the engine isrunning or hot.5. Re-start the engine and take your vehicle to a service facility.Driving th
10. Tune: Works in radio mode only.Press TUNE/ to changefrequency down/up11. Seek: Press andrelease/ for previous/nextstrong station, selection or tra
Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforerefueling your vehicle.• Al
RefuelingFuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others:• Read and follow all the instr
If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any
with the recommended octane rating, see your dealer or a qualifiedservice technician to prevent any engine damage.Fuel qualityIf you are experiencing
Replace the fuel filter with an authorized Motorcraft part. Thecustomer warranty may be void for any damage to the fuel systemif an authorized Motorcr
• Have the vehicle loading and distribution the same every time.Your results will be most accurate if your filling method is consistent.Calculating fu
• Revving the engine before turning it off may reduce fuel economy.• Using the air conditioner or defroster may reduce fuel economy.• You may want to
• Close windows for high speed driving.EPA window stickerEvery new vehicle should have the EPA window sticker. Contact yourdealer if the window sticke
Exhaust leaks may result in entry of harmful and potentiallylethal fumes into the passenger compartment.Do not make any unauthorized changes to your v
soon light is on, refer to the description in the Warning lights andchimes section of the Instrument Cluster chapter. Your vehicle may notpass the I/M
AM/FM STEREO / SINGLE CD RADIO (IF EQUIPPED)1. BAL (Balance): Press/to shift sound to the left/rightspeakers.2. FADE: Press/ to shiftsound to the fron
For E-450 and E-550 vehicles with the Hydro-Boost BrakeSystem, do not press the brake pedal after the engine has beenturned off.5. Recheck the fluid l
operated for an extended period at high speeds, in city traffic during hotweather or pulling a trailer, the vehicle should be turned off for about 30m
The transmission fluid should be inthis range if at ambient temperature(50°F-95°F [10°C-35°C]).High fluid levelFluid levels above the safe rangemay re
Automatic transmission fluid filter (if equipped)The TorqShift automatictransmission is equipped with aserviceable external fluid filtermounted on the
Air filter1. Disconnect the fresh air inlet tubefrom the radiator support.2. Open the clamp that secures thetwo halves of the air filter housingtogeth
Component14.6L V8 engine 5.4L V8 engine 6.8L V10engineOil filter FL-820-S FL-820-S FL-820-SPCV valve2Spark plugs3Automatictransmissionfilter4— FT-145
REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to line onreservoi
Fluid Ford PartNameApplication CapacityPower steeringfluidMotorcraftMERCON威 ATFAll Keep in FULLrange ondipstickRear axle4SAE 75W-140Synthetic RearAxle
Fluid Ford PartNameApplication CapacityFuel tank N/A All regular andextended lengthvans and wagons35.0 gallons(132.4L)138 inchwheelbase (exceptE-Super
meeting Ford specification EST-M2C118–A, for complete refill of 8.8 inchand 9.75 inch Traction-Lok axles.3Fill Dana rear axles to 1/4 inch to 9/16 inc
To set the minute, press and hold CLK and press TUNE to decreaseor increase the minutes.5. EJ (Eject): Press to eject a CD.6. COMP (Compression): In C
LUBRICANT SPECIFICATIONSItem Ford partnameFord partnumberFordspecificationBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluidPM-1 ESA-
Item Ford partnameFord partnumberFordspecificationAutomatictransmission(4R70/75 E)1MotorcraftMERCON威VATFXT-5-QM MERCON威VAutomatictransmissionTorqShift
Item Ford partnameFord partnumberFordspecificationDana LimitedSlip Axles3M60 (M248)E-250/350M70FF(M267FF)E-350M70HD(M273HD)E-450SAE 90 HypoidGear OilC
MERCON威 and MERCON威 V type fluids are not interchangeable.DO NOT mix MERCON威 and MERCON威 V. Use of a transmissionfluid that indicates dual usage (MERC
VEHICLE DIMENSIONSVan/wagon modelsE-150 – Inches(mm)E-250 –Inches (mm)E-350 –Inches (mm)(1) Overallheight80.7 (2050) 82.9 (2107) 84.6 (2148)(2) Trackf
Cutaway/commercial stripped chassis modelsE-350 – inches (mm) E-450 – inches (mm)(1) Overall height Refer to Body Builder for specifications.(2) Track
VEHICLE IDENTIFICATION NUMBERComplete Ford built vehiclesThe vehicle identification number is attached to your vehicle in thefollowing places:• On the
Transmission/Transaxle code designationsYou can find atransmission/transaxle code on thevehicle certification label. Thefollowing table tells you whic
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford
Scuff platesSpeed controlLifestyleMobile-ease hands-free communication systemTrailer hitches, wiring harnesses and accessoriesPeace of mindFirst aid a
14. CD: Press to enter CD mode orto play a CD already loaded into thesystem.15. AM/FM: Press to choose afrequency band in radio mode.16. BASS: Press/
AAccessory delay ...56Air cleaner filter ...223–224Airbag supplemental restraintsystem ...
Climate control (see Airconditioning or Heating) ...38, 40Clock adjust6-CD in dash ...26, 30, 34AM/FM ...
filter, specifications ...200, 224recommendations ...200refill capacities ...226specifications ...
LLampsbulb replacementspecifications chart ...46daytime running light ...42headlamps ...41hea
Seat belts(see Safety restraints) ...72Seats ...66child safety seats ...90fron
Windshield washer fluid andwipers ...51checking and adding fluid ...198replacing wiper blades...51W
246
247
248
PREMIUM IN-DASH SIX CD SOUND SYSTEM (IF EQUIPPED)1. Seek: Press and releaseSEEK/ for previous/nextstrong station, or track of thecurrent disc.2. Rewin
6. Bass: Press BASS; then pressSEL/ to decrease/increasethe bass output.Treble: Press TREB; then pressSEL/ to decrease/increasethe treble output.7. Se
10. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, press andhold a preset button until soundreturns.11. CD: Press to
17. Disc tune: Radio: Pressor to manually tune down or upthe radio frequency band. CD:Press/ to select the previous/next CD.SATELLITE COMPATIBLE AM/FM
reception is available through your dealer. Detailed Satellite instructionsare included with the dealer installed kit.Dealer installed satellite kit o
Maintenance and Specifications 195Engine compartment 197Engine oil 198Battery 201Engine Coolant 203Fuel information 209Air filter(s) 224Part numbers 2
stored in preset 1 will begin playing. If there are less than six strongstations, the system will store the last one in the remaining presets.Setting
17. BAND: Press to toggle betweenAM/FM1/FM2 frequency band.18. Memory presets: To set astation: Select frequency band; tuneto a station, press and hol
instructions are included with the dealer installed kit.Dealer installed satellite kit only available in the continental UnitedStates.For information
changing to the next field. (TEXT must be pressed within 3 seconds ofthe previous button press to proceed to the next/last text display.)TEXT is also
Compression: Brings soft and loud CD passages together for a moreconsistent listening level when in CD mode. Press MENU untilcompression status is dis
16. SAT (if equipped): Your radiocomes equipped with Satellite Readycapability. The kit to enable theSatellite reception is available through your dea
23. Disc/Tune: Press or tomanually tune down/up the radiofrequency band, or to listen to the previous/next CD.CAT: CAT is only available when equipped
• Tighten very loose tapes by inserting a finger or pencil into the holeand turning the hub.• Remove loose labels before inserting tapes.• Allow tapes
HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe
To aid in side window defogging/demisting in cold weather:1. Select MIX.2. Set the temperature control to maintain comfort.3. Set the fan speed to HI.
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
HEADLAMP CONTROL• The first position turns on theparking, tail, license plate andside marker lamps.• The outer position turns on theheadlamps.Battery
Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the ON position,• the head
PANEL DIMMER CONTROLTo adjust the brightness of theinstrument panel, rotate the dimmercontrol clockwise/counterclockwisewhen the headlamp control is i
3. Turn on the low beam headlampsand open the hood.4. Locate the high intensity area ofthe beam pattern and place the topedge of the intensity zone ev
8.• Aerodynamic: Locate the horizontal adjuster (1) for each headlamp.Turn it clockwise or counterclockwise, to place the left edge of thehigh intensi
Third row courtesy/reading/cargo lampsThe dome portion of the lamp, thecenter light, can be turned on whenthe headlamp control is rotated fullycounter
Function Number ofbulbsTrade numberHeadlamps (sealed beam) 2 H5054Headlamps (aerodynamic) 2 9007Park lamp and turn signal (front) 2 4157K or 3157KBack
4. Remove the bulb retaining ring byrotating it counterclockwise, andslide the ring off the plastic base.5. Pull the bulb straight out.Handle a haloge
3. Remove the four headlamp bulbretaining screws and the retainingring.4. Remove the headlamp.5. Disconnect the electricalconnector from the bulb and
Remember to pass on this Owner’s Guide when reselling the vehicle. Itis an integral part of the vehicle.Fuel pump shut-off switch: In the event of an
Replacing license plate lamp bulbs1. Turn the headlamp switch to OFFand then remove the two screwsand the license plate lamp assemblyfrom the rear doo
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice
Installing a garage door opener (if equipped)The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers:1. Pl
CompassThe compass display is contained in the overhead console. The vehicleheading is displayed as one of N, NE, E, SE, S, SW, W and NW.The compass r
• Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles untilCAL indicator turns off in about 2–3 complete circles.• The compass is now calib
Always keep the power point caps closed when not being used.POWER WINDOWS (IF EQUIPPED)Do not leave children unattended in the vehicle and do not letc
Standard mirrorThe spotter mirror only can be tiltedfrom top to bottom. Move the lowermirror manually up/down to increaseside and rear visibility. App
The telescoping feature (ifequipped) allows the mirror toextend approximately 3.15 inches(80 mm). This feature is especiallyuseful to the driver when
Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RES contro
BREAKING-IN YOUR VEHICLEDuring the first 1,000 miles (1,600 km) of driving, maintain speeds below70 mph (110 km/h) and vary speeds frequently. This is
• Depress the brake pedal until thedesired vehicle speed is reached,press the SET ACCEL control.Turning off speed controlThere are two ways to turn of
KEYSThe key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency.You
Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment.The typ
Sounding a panic alarmPressto activate the alarm. Press the control again, or turn theignition to the 1 (ACCESSORY) or 4 (ON) position to deactivate t
Note: Replacement of the battery will not cause the remote transmitterto become deprogrammed from your vehicle. The remote transmittershould operate n
Illuminated entryThe interior lamps illuminate when the remote entry system is used tounlock the door(s) or sound the personal alarm.The illuminated e
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Pull lever up to adjust seatback.Using the manual lumbar supportThe lumbar support control islocated on the inboard side of thedriver’s seat.Turn the
Press to raise or lower the rearportion of the seat cushion.Press the control to move the seatforward, backward, up or down.Quick release captains cha
Stow the tongue end of thedetachable anchor.2. Pull the seat latch handle, thenpull the seat toward the right side ofthe vehicle to disengage four pin
Event Data RecordingOther modules in your vehicle — event data recorders — are capable ofcollecting and storing data during a crash or near crash even
REAR SEATSAccessing the 3rd, 4th and 5th row seats (if equipped)To make access to the 4th and 5throw seats easier, attach the 3rd and4th row passenger
2. Pull the LH/RH seat latch handles(located under the seat) rearward torelease the latch hook ends from thefront strikers.3. Move the seat rearward a
SAFETY RESTRAINTSSafety restraints precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce
Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Checkseat covers and buckle
Automatic locking modeWhen to use the automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to
After any vehicle collision, the safety belt systems at all outboardseating positions (except the driver position, which does nothave this feature) mu
Front safety belt height adjustmentThe driver and front seat outboardpositions are equipped with a heightadjuster. Adjust the height of theshoulder be
Shorten and fasten the belt whennot in use.Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cl
If... Then...The driver’s safety belt is notbuckled approximately 5seconds after the safety beltwarning light has turned off...The BeltMinder娂 feature
Reasons given... Consider...“Seat belts don’twork”Safety belts, when used properly, reduce risk ofdeath to front seat occupants by 45% in cars,and by
Notice to owners of diesel-powered vehiclesRead the 6.0 Liter Power Stroke Direct Injection Turbo Diesel Owner’sGuide Supplement for information regar
• the gearshift is in P (Park) (automatic transmission)• the ignition switch is in the OFF position• all vehicle doors are closed• the driver’s safety
Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label.
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right
The National Highway Traffic Safety Administration (NHTSA)recommends a minimum distance of at least 25 cm (10 inches)between an occupant’s chest and t
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref
Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.Alwa
neck, the child should wear the lap and shoulder belt. Moving the childcloser to the center of the vehicle may help provide a good shoulder beltfit.Do
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
If your vehicle is equipped with theFord Ambulance PreparationPackage, it will be indicated on theCertification label. The label islocated on the driv
Follow all instructions provided by the manufacturer of thebooster seat.Never put the shoulder belt under a child’s arm or behind theback because it e
• LATCH lower anchors are recommended for use by children up to 48pounds (22 kg) in a child restraint. Top tether anchors can be usedfor children up t
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted.6. Allo
Attaching safety seats with tether strapsChildren should be placed in the rear in an appropriate childsafety seat that is properly secured to the vehi
1. Position the child safety seat onthe front right-hand passenger seat.2. Adjust the front right-handpassenger seat full forward.3. Route the child s
5. Adjust the front right handpassenger seat to the full rearwardposition.6. Install the child safety seat tightly using the LATCH anchors or safetybe
1. Position the child safety seat onthe second row left hand or righthand bucket seat.2. Route the child safety tetherstrap over the back of the left
2. Route the child safety tetherstrap over the back of 3–Passengerbench seat.3. Clip the tether strap hook to thetether bracket mounted under rearrail
Your vehicle may be equipped with LATCH anchors for child seatinstallation at the seating positions marked with the child seat symbol:• Five passenger
Commentaires sur ces manuels