Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 15Entertainment Systems 20Climate Controls 34Manual heating and air conditionin
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
Webbing extraction sensitive modeThe webbing sensitive locking mode locks the webbing and preventsmore belt from being pulled out if the belt is pulle
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could re
Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occup
If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2minutes h
The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate
The driver and front passenger BeltMinder娂 features can bedeactivated/activated by performing the following procedure:Before following the procedure,
Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label.
Maintenance and Specifications chapter. If the light is blinking, enginemisfire is occurring which could damage your catalytic converter. Drivein a mo
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right
Never place your arm over the air bag module as a deploying airbag can result in serious arm fractures or other injuries.Ford Motor Company recommends
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burn
Several air bag system components get hot after inflation. Do nottouch them after inflation.If the air bag has deployed, the air bag will not function
Even with the front passenger sensing system, children 12 andunder should be properly restrained in the back seat.When the front passenger seat isoccu
injury in a crash event. For example, if an occupant slouches, lies down,turns sideways, sits forward, leans forward or sideways, or puts one orboth f
Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref
All occupants of the vehicle should always wear their safety beltseven when an air bag SRS is provided.How does the side air bag system work?The desig
to inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-frontal collisions, unless the collision causes sufficient lateraldec
Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance mayoccur. It will take you longer
SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Air bag supplem
Child booster seatsChildren outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the la
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
Follow all instructions provided by the manufacturer of thebooster seat.Never put the shoulder belt under a child’s arm or behind theback because it e
• Put the safety belt in the automatic locking mode. Refer to Automaticlocking mode (passenger side front and outboard rear seatingpositions) (if equi
1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly move the seat forwardand back to m
2. Route the child safety seat tether strap over the back of the seat.For vehicles with adjustable head restraints, route the tether strap underthe he
Attaching safety seats with LATCH (Lower Anchors and Tethers forChildren) attachmentsSome child safety seats have two rigid or webbing mounted attachm
Never remove the coolant reservoir cap while the engine isrunning or hot.Traction control娂 AdvanceTrac威active (if equipped): Illuminateswhen the Tract
If you install a child seat with rigid LATCH attachments, do not tightenthe tether strap enough to lift the child seat off the vehicle seat cushionwhe
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
• Extra load: A class of P-metric or Metric tires designed to carry aheavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires].Increasing the
Inspecting your tiresPeriodically inspect the tire treads for uneven or excessive wear andremove stones, nails, glass or other objects that may be wed
higher than the manufacturer’s recommended cold inflation pressurewhich can be found on either the tire label or certification label which islocated o
TIRE REPLACEMENT REQUIREMENTSYour vehicle is equipped with tires designed to provide a safe ride andhandling capability.Only use replacement tires and
T-Type/Mini-Spare Tire Information (if equipped)Your vehicle may be equipped with a T-type/mini-spare tire. This tire willhave the words ⬙Temporary Us
When driving with the dissimilar spare tire/wheel, do not:• Exceed 70 mph (113 km/h)• Use more than one dissimilar spare tire/wheel at a time• Use com
1. Park on a level surface, activatehazard flashers and set parkingbrake.2. Place gearshift lever in P (Park),turn engine OFF and block thediagonally
Turn signal: Illuminates when theleft or right turn signal or thehazard lights are turned on. If theindicators stay on or flash faster, check for a bu
4. Remove the lug wrench from thejack. Rotate the lug wrench socketout from the handle.5. Locate pry off notch (ifequipped) and remove the centerornam
• Position the jack according to thefollowing guides and turn the jackhandle clockwise until the wheelis completely off the ground.To lessen risk of p
five black plastic nuts in the order shown on the wheelcover using thelug wrench with about 6.0 lbs. ft. (80 N•m) torque. Then firmly installthe wheel
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE CAREImproper or inadequate vehicle maintenance can also cause tires to wearabnormally. Here are some of the important maintenance items:Tire wear
Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t
Key-in-ignition warning chime: Sounds when the key is left in theignition in the OFF/LOCK or ACCESSORY position and the driver’s dooris opened.GAUGESS
The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear.Tire rotationRotating your tire
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can
Follow these guidelines when using snow tires and chains:• Either cable type chains or SAE class S chains can be used.• Install chains securely, verif
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei
GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).
Maximum Loaded Trailer Weight – is the highest possible weight of afully loaded trailer the vehicle can tow. It assumes a vehicle with onlymandatory o
The following gives you a few examples on how to calculate the availableamount of cargo and luggage load capacity:• Another example for your vehicle w
Your loaded trailer should weigh no more than 2,000 lb. (907 kg). Donot exceed the GVWR specified on the certification label.Towing trailers beyond th
Speedometer: Indicates the current vehicle speed.• Standard instrument cluster• Optional instrument clusterEngine coolant temperature gauge:• Standard
Trailer lampsTrailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working.
Launching or retrieving a boatDisconnect the wiring to the trailer before backing the trailerinto the water. Reconnect the wiring to the trailer after
STARTINGPositions of the ignition1. OFF/LOCK, shuts off the engineand all accessories/locks thegearshift lever and allows keyremoval.2. ACC, allows th
If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf
5. Turn the key to 3 (ON) withoutturning the key to 4 (START).Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to
Starting the engine1. Turn the key to 3 (ON) withoutturning the key to 4 (START).2. Turn the key to 4 (START), thenrelease the key as soon as theengin
BRAKESYour service brakes are self-adjusting. Refer to the scheduledmaintenance information for scheduled maintenance.Occasional brake noise is normal
The ABS operates by detecting theonset of wheel lockup during brakeapplications and compensates forthis tendency. The wheels areprevented from locking
Parking brake with auto-release (if equipped)Apply the parking brake wheneverthe vehicle is parked.To set the parking brake:1. Move the gearshift to P
If the parking brake fails to releaseafter completing this procedure, usethe manual parking brake releaselever.Pull the lever to manually releasethe p
• Optional instrument clusterIndicates engine coolanttemperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” a
During Traction Control娂 operation you may hear an electric motor typeof sound coming from the engine compartment and the engine will not“rev-up” when
It is also important to maintain a proper power steering fluid level in thepower steering fluid reservoir:• Do not operate the vehicle with a low powe
This system keeps the rear of your vehicle at a constant level byautomatically adding air or releasing air from the springs.If you exceed the load lim
2. Locate the access plug on theunderside of the steering columncover.3. Remove the access plug using a flat head screwdriver. Insert thescrewdriver i
2. Insert the key and turn it to ACC. Apply the brake pedal and shiftto N (Neutral).When the key is in the ignition and in the ACC position, theautoma
• Depress the brake pedal• Move the gearshift lever into the desired gearTo put your vehicle in P (Park):• Come to a complete stop• Move the gearshift
If your vehicle is equipped with afloor-shift transmission, overdrivecan be deactivated by pressing thetransmission control switch on thegearshift han
2 (Second)This position allows for second gear only.• Provides engine braking.• Use to start-up on slippery roads.• To return to(Overdrive), move the
DRIVING THROUGH WATERDo not drive quickly through standing water, especially if the depth isunknown. Traction or brake capability may be limited and i
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Trip odometer: Registers the miles (kilometers) of individual journeys.• Standard instrument clusterTo reset, depress the control.• Optional instrumen
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
The fuel pump shut-off switch islocated on the left side of the trunkbehind the left rear tail light and thetrunk liner.Use the following procedure to
Note: Always replace a fuse with one that has the specified amperagerating. Using a fuse with a higher amperage rating can cause severe wiredamage and
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 15A Taxi, Cluster, Lighting ControlModule
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description5 10A Speed control deactivation switch,Stop signal, Brake-TransmissionShif
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description16 15A Ignition (ON) - Turn signals17 10A Ignition (START) - Audio18 10A Ig
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description29 15A Audio30 15A Stop lamps, MFS31 15A Hazards (non-Police vehicles)20A H
The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 20A* Ignition switch (Key in, RUN 1,RUN
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription12 25A* Audio (non-Police vehicles only)Tray lamps (Police vehicles only)13 20A* Inst
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription108 20A** Moonroof (non-Police vehiclesonly)Spotlights (available on Policevehicles,
Engine oil pressure gauge (ifequipped): Indicates engine oilpressure. The needle should stay inthe normal operating range(between “L” and “H”). If the
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription2041⁄2ISO relay PCM205 — Not used2061⁄2ISO relay Fuel207 — Not used208 — Not used2091
JUMP STARTING YOUR VEHICLEThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury
Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
Seating and Safety Restraints 90Seating 90Safety restraints 95Air bags 110Child restraints 120Tires, Wheels and Loading 131Tire Information 132Changin
AM/FM STEREO SINGLE CD PREMIUM AUDIO SYSTEM(IF EQUIPPED)1. CD slot: Insert a CD, label sideup. With the ignition on, the radiowill begin play when a C
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai
Board membershipThe Board consists of:• Three consumer representatives• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa
Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral
concern have been unsatisfactory, Ford of Canada participates in animpartial third party mediation/arbitration program administered by theCanadian Mot
details about Ford Extended Service Plan coverage options, or visit theFord ESP website at www.ford-esp.com.GETTING ASSISTANCE OUTSIDE THE U.S. AND CA
Or call:For a free publication catalog, order toll free: 1-800-782-4356Monday-Friday 8:00 a.m. - 6:00 p.m. ESTHelm, Incorporated can also be reached b
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips.• Always
• Cover the highlighted areas to prevent water damage when cleaningthe engine.• Never wash or rinse the engine while it is running; water in therunnin
• Do not use abrasives, as they may cause scratches.• Do not use fuel, kerosene, or paint thinner to clean any parts.• Wiper blades can be cleaned wit
5. Eject: Press to eject the CD. Ifthe disc is not removed within theallotted time, the system willautomatically reload the CD and begin play. Note: T
• Never saturate the seat covers with cleaning solution.• Do not use household cleaning products or glass cleaners, which canstain and discolor the fa
exceed rigid specifications. For best results, use the following productsor products of equivalent quality:Motorcraft Bug and Tar Remover (ZC-42)Motor
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide sc
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under theinstrument panel.2. Go to the front of the vehicle andrelease the
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.•
• If required, add engine oil to theengine. Refer to Adding engineoil in this chapter.• Do not overfill the enginewith oil. Oil levels above thismark
Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oil.Only use oils “Certified For Gasoline Engines” by t
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a
When activated, AUTOSET will momentarily appear in the display whenany of the preset controls are pressed.Speed sensitive volume: Radio volume changes
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur
coolant degas system with a pressurized cap, or if it is necessary toremove the coolant pressure relief cap on the radiator of a vehicle withan overfl
Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut
What you should know about fail-safe coolingIf the engine coolant supply is depleted, this feature allows the vehicle tobe driven temporarily before i
• The air conditioning system will be disabled.Continued operation will increase the engine temperature:• If your vehicle is equipped with digital gau
If you do not use the proper fuel filler cap, excessive pressure orvacuum in the fuel tank may damage the fuel system or causethe fuel cap to disengag
splashed on the skin, promptly wash skin thoroughly with soap andwater. Consult a physician immediately if you experience an adversereaction.When refu
When fueling your vehicle:1. Turn the engine off.2. Carefully turn the filler cap counterclockwise 1/4 of a turn until itstops.3. Pull to remove the c
16. SCAN: Press SCAN to hear abrief sampling of radio stations orCD tracks. Press again to stop.PREMIUM/AUDIOPHILE SATELLITE COMPATIBLE AM/FM STEREOSI
Repairs to correct the effects of using a fuel for which your vehicle wasnot designed may not be covered by your warranty.Octane recommendationsYour v
If you have run out of fuel:• You may need to cycle the ignition from OFF to ON several times afterrefueling, to allow the fuel system to pump the fue
For consistent results when filling the fuel tank:• Turn the engine/ignition switch to the off position prior to refueling,an error in the reading wil
Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin
• Adding certain accessories to your vehicle (for example bugdeflectors, rollbars/light bars, running boards, ski/luggage racks) mayreduce fuel econom
emission control, such non-Ford parts should be equivalent to genuineFord Motor Company parts in performance and durability.Do not park, idle, or driv
These temporary malfunctions can be corrected by filling the fuel tankwith good quality fuel and/or properly tightening the fuel cap. After threedrivi
2. While the engine idles, turn the steering wheel left and right severaltimes.3. Turn the engine off.4. Check the fluid level in thereservoir. It sho
weather or pulling a trailer, the vehicle should be turned off for about 30minutes to allow fluid to cool before checking.1. Drive the vehicle 20 mile
The transmission fluid should be inthis range if at normal operatingtemperature (150°F-170°F[66°C-77°C]).The transmission fluid should be inthis range
3. BASS: Press BASS; thenpressSEL-TEXT todecrease/increase the level of bassoutput.TREB (Treble): Press TREB; thenpressSEL-TEXT todecrease/increase th
If an overfill occurs, excess fluidshould be removed by a qualifiedtechnician.An overfill condition oftransmission fluid may causeshift and/or engagem
Note: Failure to use the correct air filter element may result in severeengine damage. The customer warranty may be voided for any damage tothe engine
REFILL CAPACITIESFluid Ford Part Name CapacityEngine oil (includesfilter change)6Motorcraft SAE 5W-20Premium SyntheticBlend Motor Oil (US)Motorcraft S
3Indicates only approximate dry-fill capacity. Some applications may varybased on cooler size and if equipped with an in-tank cooler. The amountof tra
Item Ford partnameFord partnumberFordspecificationEngine oil Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcraft SAE5W-20 SuperPremium
2Add 118 ml (4 oz.) of Additive Friction Modifier XL-3 or equivalentmeeting Ford specification EST-M2C118-A for complete refill ofTraction-Lok rear ax
142005 Crown Victoria (cro)Owners Guide (post-2002-fmt)USA_English (fus)Maintenance and Specifications246
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
Engine numberThe engine number (the last eight numbers of the vehicle identificationnumber) is stamped on the engine block, transmission, frame andtra
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford
stations are independently operated and individually elect to use RDStechnology to transmit station ID and program type as desired.FIND Program type:
Peace of mindFirst aid and safety kitsFull vehicle coversLocking gas capRemote startVehicle security systemsMobile-ease hands-free communication syste
AABS (see Brakes) ...166Air bag supplemental restraintsystem ...110, 117and child safety seats ...
Compass, electronicset zone adjustment ...52Console ...75overhead ...50–
Fuel ...226calculating fuel economy..54, 231cap ...228capacity ...
LLampsautolamp system ...38bulb replacementspecifications chart ...42daytime running light ...38headlam
SSafety Belt Maintenance ...109Safety belts (see Safetyrestraints) ...95, 98, 100–102Safety defects, reporting ...205Safety r
VVehicle dimensions ...245Vehicle Identification Number(VIN) ...247Vehicle loading ...
Dolby: Works in tape mode to reduces tape noise and hiss. Press MENUuntil DOLBY XX appears in the display. PressSEL-TEXT totoggle ON/OFF.The Dolby威 no
13. SCAN: Press SCAN to hear abrief sampling of radio stations,selections or CD tracks. Press againto stop.14. SHUF (Shuffle): Press to playthe tracks
AUDIOPHILE AM/FM STEREO IN-DASH SIX CD SOUND SYSTEM(IF EQUIPPED)1. CD slot: To insert a CD, pressLOAD. When the system is ready,insert a CD, label sid
4. MUTE: Press to mute the playingmedia. Press again to return to theplaying media or turn the volumecontrol to adjust the volume.5. Eject: Press to e
Cleaning 206Maintenance and Specifications 212Engine compartment 213Engine oil 214Battery 218Engine Coolant 220Fuel information 226Air filter(s) 240Pa
9. MENU: Press MENU repeatedlyto access RDS on/off.UseSEL-TEXT to toggleRDS on/off. Press MENU again to access Program type mode or ShowType mode. (ME
Speed sensitive volume: Radio volume changes automatically andslightly with vehicle speed to compensate for road and wind noise.Recommended level is 1
RADIO FREQUENCIESAM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsComm
Don’t:• Expose discs to direct sunlight or heat sources for extended periodsof time.• Insert more than one disc into each slot of the CD changer magaz
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature sele
To aid in side window defogging/demisting in cold weather:1. Select NORM A/C.2. Adjust the temperature control to maintain comfort.3. Set the fan spee
3. Fan speed: Turn to manuallyincrease or decrease fan speed.4. Defrost:Distributes outside air through the windshield defrostervents and the side win
• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield.To aid in side window defogging/demisting in cold weather:1. Se
HEADLAMP CONTROLTurns the lamps off.Turns on the parkinglamps, instrument panel lamps,license plate lamps and tail lamps.Turns the headlamps on.Autola
Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Light (DRL) Systemdoes not activate your tail lamps
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
Domelamp ControlThe panel dimmer control also controls the domelamp operation.• Rotate the thumbwheel fully to the right, past detent to activate thed
With overhead consoleWith overhead console and moonroofTo turn on the map lamps, press themap lamp control.REAR COURTESY/READING LAMPSRotate the lens
Replacing exterior bulbsCheck the operation of all the bulbs frequently.Using the right bulbsReplacement bulbs are specified in the chart below. Headl
Replacing headlamp bulbsTo remove the headlamp bulb:1. Make sure headlamp switch is in OFF position, then open the hood.2. Remove the radiator cover b
2. Install the bulb retaining ring over the plastic base until it contacts therear of the socket by rotating it clockwise until you feel a “stop.”3. C
Replacing tail lamp/brake/turn lamp bulbsThe tail lamp, the brake lamp and the turn signal lamp bulbs are locatedin the tail lamp assembly. Follow the
Replacing license plate lamp bulbs1. Make sure headlamp switch is inOFF position, then remove twoscrews, grommets and the licenseplate lamp assembly f
3. Carefully pull the bulb socket outof the lamp assembly.4. Pull the bulb straight out of thesocket and push in the new bulb.To install, reverse the
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
4. Clean blades and glass as recommended in Cleaning chapter andreplace wiper blades at least once per year or before winter for optimumperformancePoo
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
Slide on rod feature (ifequipped)Rotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage.Note: To stow the viso
3. Press and hold the MODE controluntil VAR appears in the display,then release. The display shouldshow the current zone number.4. Press the MODE cont
3. From a blank display press andrelease the MODE button once. Thedirectional heading will bedisplayed.Note: If the compass isde-calibrated, CAL will
4. Determine which magnetic zoneyou are in by referring to the zonemap.5. Repeatedly press and release theRESET button to scroll through thezones 1–15
4. Press the RESET button tode-calibrate the compass. Thedisplay will read CIRCLE SLOWLYTO CALIBRATE for a few secondsand then display a direction wit
ProgrammingDo not program the HomeLink威 with the vehicle parked in thegarage.Note: Some vehicles may require the ignition switch to be turned to these
3. Simultaneously press and holdboth the HomeLink威 and hand-heldtransmitter button. The messageCHANNEL “X” (1,2 or 3) TRAININGwill appear on the displ
If the indicator light(s) underneath the house icon blink rapidly for twoseconds and then turn to a continuous light, proceed with steps 6through 8 to
Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and release the appropriate HomeLink威 button.Activation will now occur for the
Reprogramming a single HomeLink姞 buttonTo program a device to HomeLink威 using a HomeLink威 button previouslytrained, follow these steps:1. Press and ho
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
POWER WINDOWSDo not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injurethemselves.W
POWER SIDE VIEW MIRRORSTo adjust your mirrors:1. Selectto adjust the leftmirror orto adjust the rightmirror.2. Move the control in the directionyou wi
(darkened) state when bright lights (glare) reach the mirror. When themirror detects bright light from behind the vehicle, it will automaticallyadjust
Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas
Resuming a set speedPress the RESUME control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RESUME control w
• Depress the brake pedal until thedesired vehicle speed is reached,press the SET + control.Turning off speed controlThere are two ways to turn off th
In any mode:• Press VOL + or - to adjust thevolume.Climate control features• Press TEMP + or - to adjusttemperature.MOON ROOF (IF EQUIPPED)To open the
Do not let children play with the moon roof or leave childrenunattended in the vehicle. They may seriously hurt themselves.When closing the moon roof,
1. Press and hold the two outsidebuttons releasing only when theindicator light begins to flash after20 seconds. Do not repeat Step 1to program additi
6. At the garage door opener receiver (motor-head unit) in the garage,locate the “learn” or “smart” button (usually near where the hangingantenna wire
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental restraint
Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet
ELECTRONIC MESSAGE CENTER (IF EQUIPPED)The electronic message center onlyworks when the ignition is in theON position.The message center allows you to
SelectEach press of the SELECT controlwill select a different function.• Press the right side of the controlto advance the function to theright.• Pres
The message center will remain inthe DTE function until the SELECTcontrol is pressed to changefunctions.DTE is calculated using a runningaverage fuel
TRIP A and TRIP BThese two functions allow you tosee how far you have traveled sinceyou last reset. Trip A and Trip B arecompletely independent and mu
CELL PHONE USEThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri
POSITIVE RETENTION FLOOR MATPosition the driver floor mat so thatthe eyelet is over the pointed end ofthe retention post and rotateforward to lock in.
KEYSThe vehicle is equipped with a master (black) key and valet (gray) keylock system. The master key will access doors, trunk, glove box, ignitionand
Childproof door locksWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo
Keep vehicle doors andluggage compartmentlocked and keep keys and remotetransmitters out of a child’s reach.Unsupervised children could lockthemselves
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
The remote entry system allows you to lock or unlock all vehicle doorswithout a key.The remote entry features operatewith the ignition in any position
3. Cycle the ignition from the 3 (ON) to the 1 (OFF/LOCK) position.4. Press the power door unlock control three times.5. Turn the ignition to the 3 (O
To replace the battery:1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIR
• Perform the following programming procedure yourself:Place the key in the ignition andcycle from 1 (OFF/LOCK) to 3 (ON)eight times in rapid successi
Autolock (if equipped)This feature automatically locks all vehicle doors when:• all doors are closed,• the ignition is in the 3 (ON) position,• the br
KEYLESS ENTRY SYSTEM (IF EQUIPPED)With the keyless entry keypad, youcan:• lock or unlock the vehicle doorswithout using the key.• open the trunk.See a
3. Enter a second personal 5-digit code. Each number must be enteredwithin five seconds of each other.4. Press 3 • 4 to store the second personal code
• To release the trunk, enter the factory-set code or personal code(driver door unlocks) and press 5 • 6 within five seconds.After the factory-set cod
• When the ignition is in the 3 (ON) position, the indicator will glow for3 seconds to indicate normal system functionality.If a problem occurs with t
Programming spare keysA maximum of eight keys can be coded to your vehicle. OnlySecuriLock娂 keys can be used. To program a coded key yourself, youwill
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
SEATINGAdjustable head restraintsYour vehicle’s seats are equipped with head restraints which arevertically adjustable. The purpose of these head rest
Lift handle to move seat forward orbackward.Pull lever up to adjust seatback.Using the manual recline function (if equipped)Never adjust the driver’s
To adjust the front seatback usingthe manual recliner:• Lift and hold the handle locatedon the side of the seat.• Lean against the seatback toadjust i
Adjusting the power front seats – door mounted controls(if equipped)The controls for the power seats are located on the inside of each frontdoor.Never
Press to move the seat forward orbackward.Press to move the front portion ofthe seat cushion up or down.Press to move the rear portion ofthe seat cush
Seat mounted cup holders and armrest storage compartment(if equipped)Your vehicle is equipped with cupholders in the rear seat armrest. Toaccess the c
How does the Personal Safety System work?The Personal Safety System can adapt the deployment strategy of yourvehicle’s safety devices according to cra
in rear-facing child seats, this occurs because they are initially sittingvery close to the airbag. For other occupants, this occurs when theoccupant
of the safety belts and helps properly position the occupant relative tothe airbag to improve protection. The safety belt pretensioners can beeither a
To reduce the risk of injury, make sure children sit in the backseat where they can be properly restrained.Never let a passenger hold a child on his o
Commentaires sur ces manuels