Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 15Entertainment Systems 20AM/FM stereo cassette with CD 20AM/FM stereo with CD
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Checkseat covers and buckle
movement. For example, if the driver brakes suddenly or turns a cornersharply, or the vehicle receives an impact of approximately 5 mph(8 km/h) or mor
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could re
Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occup
If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2minutes h
The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to infla
To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle.1. Turn the ignition switch to the RUN (or O
Safety belt maintenanceInspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to ma
Maintenance and Specifications chapter. If the light is blinking, enginemisfire is occurring which could damage your catalytic converter. Drivein a mo
Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in
Do not attempt to service, repair, or modify the steering column,its adaptive module, or its fuses. See your Ford or LincolnMercury dealer.To properly
Children and air bagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rea
The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burn
If the air bag has deployed, the air bag will not functionagain and must be replaced immediately. If the air bag is notreplaced, the unrepaired area w
When the front passenger seat isoccupied and the sensing systemhas turned off the passenger’sfrontal airbag, the ⬙passenger airbagoff⬙ or ⬙pass airbag
Sitting improperly out of position or with the seat back reclinedtoo far can take off weight from the seat cushion and affect thedecision of the passe
Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref
All occupants of the vehicle should always wear their safety beltseven when an air bag SRS is provided.How does the side air bag system work?The desig
to inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-frontal collisions, unless the collision causes sufficient lateraldec
Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance mayoccur. It will take you longer
SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Air bag supplem
Child booster seatsChildren outgrow a typical convertible or toddler seat when they weigh40 pounds (18 kg) and are around 4 years of age. Although the
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
Follow all instructions provided by the manufacturer of thebooster seat.Never put the shoulder belt under a child’s arm or behind theback because it e
• LATCH lower anchors are recommended for use by children up to 48pounds (22 kg) in a child restraint. Top tether anchors can be usedfor children up t
1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly move the seat forwardand back to m
2. Route the child safety seat tether strap over the back of the seat.For vehicles with adjustable head restraints, route the tether strap underthe he
This type of child seat eliminates the need to use seat belts to attach thechild seat. For forward-facing child seats, the tether strap must also beat
Never remove the coolant reservoir cap while the engine isrunning or hot.Traction control娂 AdvanceTracactive (if equipped): Illuminateswhen the Tracti
lifting the front of the child seat. Keeping the child seat just touching thevehicle seat gives the best protection in a severe crash.Each time you us
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
• Extra load: A class of P-metric or Metric tires designed to carry aheavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires].Increasing the
Inspecting your tiresPeriodically inspect the tire treads for uneven or excessive wear andremove stones, nails, glass or other objects that may be wed
higher than the manufacturer’s recommended cold inflation pressurewhich can be found on either the tire label or certification label which islocated o
TIRE REPLACEMENT REQUIREMENTSYour vehicle is equipped with tires designed to provide a safe ride andhandling capability.Only use replacement tires and
When driving with the T-type/mini-spare tire do not:• Exceed 50 mph (80 km/h)• Load the vehicle beyond maximum vehicle load rating listed on theSafety
• Use snow chains on the end of the vehicle with the dissimilar sparetire/wheelThe usage of a dissimilar spare tire/wheel can lead to impairment of th
1. Park on a level surface, activatehazard flashers and set parkingbrake.2. Place gearshift lever in P (Park),turn engine OFF and block thediagonally
Turn signal: Illuminates when theleft or right turn signal or thehazard lights are turned on. If theindicators stay on or flash faster, check for a bu
4. Remove the lug wrench from thejack. Rotate the lug wrench socketout from the handle.5. Locate pry off notch (ifequipped) and remove the centerornam
• Position the jack according to thefollowing guides and turn the jackhandle clockwise until the wheelis completely off the ground.To lessen risk of p
five black plastic nuts in the order shown on the wheelcover using thelug wrench with about 6.0 lbs. ft. (80 N•m) torque. Then firmly installthe wheel
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
the road in adverse (wet, snowy, etc.) conditions. Visually check yourtires for uneven wear, looking for high and low areas or unusuallysmooth areas.
• Avoid potholes and objects on the road• Do not run over curbs or hit the tire against a curb when parkingIf your vehicle is stuck in snow, mud, sand
Key-in-ignition warning chime: Sounds when the key is left in theignition in the OFF/LOCK or ACCESSORY position and the driver’s dooris opened.GAUGESS
Tire rotationRotating your tires at the recommended interval (as indicated in theScheduled Maintenance Guide that comes with your vehicle) will helpyo
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can
Follow these guidelines when using snow tires and chains:• Either cable type chains or SAE class S chains can be used.• Install chains securely, verif
Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue loador king pin w
GVW (Gross Vehicle Weight) – is the Vehicle Curb Weight + cargo +passengers.GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle.3. Subtract the combined weight of the driver and pas
TRAILER TOWINGYour vehicle is classified as a light duty towing vehicle. Do not tow atrailer until your vehicle has been driven at least 2,000 miles (
Trailer lampsTrailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working.
Launching or retrieving a boatDisconnect the wiring to the trailer before backing the trailerinto the water. Reconnect the wiring to the trailer after
Speedometer: Indicates the current vehicle speed.• Standard instrument cluster• Optional instrument clusterEngine coolant temperature gauge:• Standard
STARTINGPositions of the ignition1. OFF/LOCK, shuts off the engineand all accessories/locks thegearshift lever and allows keyremoval.2. ACC, allows th
If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf
5. Turn the key to 3 (ON) withoutturning the key to 4 (START).Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to
Starting the engine1. Turn the key to 3 (ON) withoutturning the key to 4 (START).2. Turn the key to 4 (START), thenrelease the key as soon as theengin
BRAKESYour service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance.Occasional brake noise is normal and o
The ABS operates by detecting theonset of wheel lockup during brakeapplications and compensates forthis tendency. The wheels areprevented from locking
Parking brake with auto-release (if equipped)Apply the parking brake wheneverthe vehicle is parked.To set the parking brake:1. Move the gearshift to P
If the parking brake fails to releaseafter completing this procedure, usethe manual parking brake releaselever.Pull the lever to manually releasethe p
During Traction Control娂 operation you may hear an electric motor typeof sound coming from the engine compartment and the engine will not“rev-up” when
It is also important to maintain a proper power steering fluid level in thepower steering fluid reservoir:• Do not operate the vehicle with a low powe
• Optional instrument clusterIndicates engine coolanttemperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” a
This system keeps the rear of your vehicle at a constant level byautomatically adding air or releasing air from the springs.If you exceed the load lim
2. Locate the access plug on theunderside of the steering columncover.3. Remove the access plug using a flat head screwdriver, then push andhold the o
2. Insert the key and turn it to OFF. Apply the brake pedal and shiftto N (Neutral).When the key is in the ignition and in the OFF position, theautoma
• Depress the brake pedal• Move the gearshift lever into the desired gearTo put your vehicle in P (Park):• Come to a complete stop• Move the gearshift
If your vehicle is equipped with afloor-shift transmission, overdrivecan be deactivated by pressing thetransmission control switch on thegearshift han
2 (Second)This position allows for second gear only.• Provides engine braking.• Use to start-up on slippery roads.• To return to(Overdrive), move the
DRIVING THROUGH WATERDo not drive quickly through standing water, especially if the depth isunknown. Traction or brake capability may be limited and i
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
The fuel pump shut-off switch islocated on the left side of the trunkbehind the left rear tail light and thetrunk liner.Use the following procedure to
Trip odometer: Registers the miles (kilometers) of individual journeys.• Standard instrument clusterTo reset, depress the control.• Optional instrumen
Note: Always replace a fuse with one that has the specified amperagerating. Using a fuse with a higher amperage rating can cause severe wiredamage and
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 15A Taxi, Cluster, Lighting ControlModule
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description5 10A Speed control deactivation switch,Stop signal, Brake-TransmissionShif
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description16 15A Ignition (ON) - Turn signals17 10A Ignition (START) - Audio18 10A Ig
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description29 15A Audio30 15A Stop lamps, MFS31 15A Hazards (non-Police vehicles)20A H
The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 20A* Ignition switch (Key in, RUN 1,RUN
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription12 25A* Audio (non-Police vehicles only)Tray lamps (Police vehicles only)13 20A* Inst
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription108 20A** Moonroof (non-Police vehiclesonly)Spotlights (available on Policevehicles,
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription2041⁄2ISO relay PCM205 — Not used2061⁄2ISO relay Fuel207 — Not used208 — Not used2091
JUMP STARTING YOUR VEHICLEThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury
Engine oil pressure gauge (ifequipped): Indicates engine oilpressure. The needle should stay inthe normal operating range(between “L” and “H”). If the
Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai
Board membershipThe Board consists of:• Three consumer representatives• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa
Seating and Safety Restraints 90Seating 90Safety restraints 95Air bags 109Child restraints 120Tires, Wheels and Loading 131Tire Information 132Changin
PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED)1. Eject: Press to eject a tape.2. Eject: Press to eject a CD.3. Bass: Allows you to increase ord
Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a
If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam
• Cover the highlighted areas to prevent water damage when cleaningthe engine.• Never wash or rinse the engine while it is running; water in therunnin
• Do not use fuel, kerosene, or paint thinner to clean any parts.• Wiper blades can be cleaned with isopropyl (rubbing) alcohol orwindshield washer so
Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing.Do not use chemical solvents or
Motorcraft Vinyl Cleaner (Canada only) (CXC-93)Motorcraft Vinyl Conditioner (Canada only) (CXC-94)Motorcraft Deluxe Leather and Vinyl Cleaner (not ava
Fade: Allows you to shift speakersound between the front and rearspeakers. Press FADE then pressSEL to shift the sound to the rearor the front .5. COM
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
Working with the engine on1. Set the parking brake and shift to P (Park).2. Block the wheels.Note: Do not start your engine with the air cleaner remov
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.6L SOHC V8 engine1. Brake fluid reservoir2. Engine oil dipstick3. Windshield washer fluid reservoir4
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.•
• If required, add engine oil to theengine. Refer to Adding engineoil in this chapter.• Do not overfill the enginewith oil. Oil levels above thismark
Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oil.Only use oils “Certified For Gasoline Engines” by t
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a
If the battery has been disconnected or a new battery has been installed,the clock and radio settings must be reset once the battery isreconnected.• A
9. RDS: (Radio Data System):Allows you to access FM stationswhich are RDS- equipped. PressRDS then SEL to select from:Traffic — Allows you to receive
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur
remove the coolant pressure relief cap on the radiator of a vehicle withan overflow system, follow these steps to add engine coolant.To reduce the ris
Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut
What you should know about fail-safe coolingIf the engine coolant supply is depleted, this feature allows the vehicle tobe driven temporarily before i
• The air conditioning system will be disabled.Continued operation will increase the engine temperature:• If your vehicle is equipped with digital gau
If you do not use the proper fuel filler cap, excessive pressure orvacuum in the fuel tank may damage the fuel system or causethe fuel cap to disengag
splashed on the skin, promptly wash skin thoroughly with soap andwater. Consult a physician immediately if you experience an adversereaction.When refu
If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any
with the recommended octane rating, see your dealer or a qualifiedservice technician to prevent any engine damage.Fuel qualityIf you are experiencing
14. AM/FM/CD: Press AM/FM toselect a radio frequency. Press whilein tape or CD mode to return toradio mode. Press CD to enter CD mode and to play a CD
Replace the fuel filter with an authorized Motorcraft part. Thecustomer warranty may be void for any damage to the fuel systemif an authorized Motorcr
• Have the vehicle loading and distribution the same every time.Your results will be most accurate if your filling method is consistent.Calculating fu
• Revving the engine before turning it off may reduce fuel economy.• Using the air conditioner or defroster may reduce fuel economy.• You may want to
• Close windows for high speed driving.EPA window stickerEvery new vehicle should have the EPA window sticker. Contact yourdealer if the window sticke
Exhaust leaks may result in entry of harmful and potentiallylethal fumes into the passenger compartment.Do not make any unauthorized changes to your v
soon light is on, refer to the description in the Warning lights andchimes section of the Instrument Cluster chapter. Your vehicle may notpass the I/M
4. Check the fluid level in thereservoir. It should be between theMIN and MAX lines. Do not addfluid if the level is in this range.5. If the fluid is
2. Park the vehicle on a level surface and engage the parking brake.3. With the parking brake engaged and your foot on the brake pedal,start the engin
The transmission fluid should be inthis range if at ambient temperature(10°C-35°C [50°F-95°F]).High fluid levelFluid levels above the safe rangemay re
AIR FILTER MAINTENANCERefer to the scheduled maintenance guide for the appropriate intervalsfor changing the air filter element.When changing the air
AM/FM STEREO / SINGLE CD RADIO (IF EQUIPPED)1. Balance: Press/ to shiftsound to the left/right speakers.2. Fade: Press/ to shiftsound to the front/rea
MOTORCRAFT PART NUMBERSComponent 4.6L SOHC V8 engineAir filter element FA-1668Fuel filter FG-986BBattery-standard BXT-65–650Battery-heavy duty BXT-65–
REFILL CAPACITIESFluid Ford Part Name CapacityEngine oil (includesfilter change)6Motorcraft SAE 5W-20Premium SyntheticBlend Motor Oil (US)Motorcraft S
3Indicates only approximate dry-fill capacity. Some applications may varybased on cooler size and if equipped with an in-tank cooler. The amountof tra
Item Ford partnameFord partnumberFordspecificationEngine oil Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcraft SAE5W-20 SuperPremium
2Add 118 ml (4 oz.) of Additive Friction Modifier XL-3 or equivalentmeeting Ford specification EST-M2C118-A for complete refill ofTraction-Lok rear ax
14REVIEW COPY2005 Crown Victoria (cro), Owners Guide (post-2002-fmt) (own2002),Market: USA_English (fus)Maintenance and Specifications245
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
Engine numberThe engine number (the last eight numbers of the vehicle identificationnumber) is stamped on the engine block, transmission, frame andtra
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford
Peace of mindFirst aid and safety kitsFull vehicle coversLocking gas capRemote startVehicle security systemsFor maximum vehicle performance, keep the
To set the minute, press and hold CLK and press TUNE to decreaseor increase the minutes.5. EJ (eject): Press to eject a CD.6. COMP (Compression): In C
14. CD: Press to enter CD mode orto play a CD already loaded into thesystem.15. AM/FM: Press to choose afrequency band in radio mode.16. Bass: Press/
AM/FM STEREO (IF EQUIPPED)1. Seek: Press/ to find thenext strong station down/up thefrequency band.2. Tune: Press/ to manuallychange radio frequency d
5. Power/volume: Press to turnON/OFF; turn to increase ordecrease volume levels.6. Tone: Press TONE until thedesired level — Bass, Treble, Fadeappears
AM/FM STEREO CASSETTE (IF EQUIPPED)1. Balance: Press to shift sound tothe left/right speakers.2. Fade: Press to shift sound to therear/front speakers.
Maintenance and Specifications 210Engine compartment 212Engine oil 213Battery 217Fuel information 225Air filter(s) 239Part numbers 240Refill capacitie
4. Tape AMS: In tape mode, pressand hold to activate AutomaticMusic Search (allows you to quicklylocate the beginning of the tape selection being play
13. AM/FM: Press to choose afrequency band in radio mode.14. Bass: Press/ todecrease/increase the bass output.15. Treble: Press/ todecrease/increase t
3. Turn the magazine (A) over.4. Using the disc holder releaseknob (C), pull the disc holder (B)out of the magazine.Do not pull too hard on the disc h
RADIO RECEPTION FACTORSThere are three factors that can affect radio reception:• Distance/strength: The further you travel from an FM station, theweak
CD units are designed to play commercially pressed 4.75 in (12cm) audio compact discs only. Due to technical incompatibility,certain recordable and re
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature sele
To aid in side window defogging/demisting in cold weather:1. Select NORM A/C.2. Modulate the temperature control to maintain comfort.3. Set the fan sp
3. Fan speed: Turn to manuallyincrease or decrease fan speed.4. Defrost:Distributes outside air through the windshield defrostervents and the side win
• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield.To aid in side window defogging/demisting in cold weather:1. Se
HEADLAMP CONTROLTurns the lamps off.Turns on the parkinglamps, instrument panel lamps,license plate lamps and tail lamps.Turns the headlamps on.Autola
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Light (DRL) Systemdoes not activate your tail lamps
Domelamp ControlThe panel dimmer control also controls the domelamp operation.• Rotate the thumbwheel fully to the right, past detent to activate thed
With overhead consoleWith overhead console and moonroofTo turn on the map lamps, press themap lamp control.REAR COURTESY/READING LAMPSRotate the lens
BULBSReplacing exterior bulbsCheck the operation of all the bulbs frequently.Using the right bulbsReplacement bulbs are specified in the chart below.
Replacing headlamp bulbsTo remove the headlamp bulb:1. Make sure headlamp switch is in OFF position, then open the hood.2. Remove the radiator cover b
3. Connect the electrical connector into the rear of the plastic base untilit snaps, locking it into position.4. Install the protective cover over hea
Replacing tail lamp/brake/turn lamp bulbsThe tail lamp, the brake lamp and the turn signal lamp bulbs are locatedin the tail lamp assembly. Follow the
Replacing license plate lamp bulbs1. Make sure headlamp switch is inOFF position, then remove twoscrews, grommets and the licenseplate lamp assembly f
3. Carefully pull the bulb socket outof the lamp assembly.4. Pull the bulb straight out of thesocket and push in the new bulb.To install, reverse the
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
6. To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of
The compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antenna. Magneticor metallic objec
OVERHEAD CONSOLE WITH MOON ROOF (IF EQUIPPED)The appearance of your vehicle’s overhead console will vary according toyour option package. Some of the
2. Hold down the MODE button for5 seconds to enter zone mode. Thedisplay will read PRESS RESET TOSET ZONE XX where XX is thecurrent zone.3. Release th
2. Hold down the MODE button for10 seconds to enter the calibrationmode. The display will read PRESSRESET TO DECAL.3. Release the MODE button.4. Press
the door to stop and reverse, does not meet current U.S. federal safetystandards. For more information, contact HomeLink威 at:www.homelink.com or 1–800
2. Position the end of your hand-held transmitter 1–3 inches (2–8 cm)away from the HomeLink威 button you wish to program (located on youroverhead conso
underneath the house icon are constant, programming is complete andyour device should activate when the HomeLink威 button is pressed andreleased. Note:
• Continue to press and hold theHomeLink威 button (note step 3in the “Programming” section)while you press and release —every two seconds (“cycle”)your
• After about 20 seconds, themessage CHANNELS CLEAREDwill appear on the display. Do nothold for longer that 30 seconds.HomeLink威 is now in the train(o
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
AUXILIARY POWER POINT (12VDC)The auxiliary power point for five passenger vehicles is located in thefloor console storage bin. For six passenger vehic
One touch downAllows the driver’s window to openfully without holding the controldown. Press completely down onthe bottom part of the rocker switchand
Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re
POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is
3. Press the SET + control andrelease it.4. Take your foot off the acceleratorpedal.5. The message “SPEED CONTROL”(if equipped) will be displayed inth
Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET + controluntil you get to the desiredspeed,
Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal. This willnot erase your vehicle’spreviously set s
Climate control features• Press TEMP + or - to adjusttemperature.MOON ROOF (IF EQUIPPED)To open the moon roof:• Press and hold the controlforward to r
When programming your HomeLink威 Wireless Control System toa garage door or gate, be sure that people and objects are out ofthe way to prevent potentia
3. Simultaneously press and holdboth the HomeLink威 and hand-heldtransmitter button. Do not releasethe buttons until step 4 has beencompleted.Some entr
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental restraint
Gate Operator & Canadian ProgrammingDuring programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time for
Erasing HomeLink姞 buttonsTo erase the three programmedbuttons (individual buttons cannotbe erased):• Press and hold the two outerHomeLink威 buttons unt
• check the distance traveled during a trip on either Trip A or Trip B• monitor the average speedSelectable featuresResetPress this control to reset t
2. Press the RESET control and theselected message center functionwill be reset to zero.Message center functionsDISTANCE TO EMPTY (DTE)This function e
AVG FUEL ECONOMY (average fuel economy)Select this function to display youraverage fuel economy in miles/gallonor liters/100 km.If you calculate your
To reset either trip feature to zero,press the RESET control while theappropriate trip distance feature(TRIP A or TRIP B) is displayed.AVG SPEED (aver
A driver’s first responsibility is the safe operation of the vehicle.The most important thing you can do to prevent a crash is toavoid distractions an
KEYSThe vehicle is equipped with a master (black) key and valet (gray) keylock system. The master key will access doors, trunk, glove box, ignitionand
Childproof door locksWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo
Keep vehicle doors andluggage compartmentlocked and keep keys and remotetransmitters out of a child’s reach.Unsupervised children could lockthemselves
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
The remote entry system allows you to lock or unlock all vehicle doorswithout a key.The remote entry features operatewith the ignition in any position
4. Press the power door unlock control three times.5. Turn the ignition to the 3 (ON) position. The doors will lock andunlock.6. With the ignition sti
To replace the battery:1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIR
Place the key in the ignition andcycle from 1 (OFF/LOCK) to 3 (ON)eight times in rapid successionwithin 10 seconds. After doorslock/unlock, press any
Autolock (if equipped)This feature automatically locks all vehicle doors when:• all doors are closed,• the ignition is in the 3 (ON) position,• the br
KEYLESS ENTRY SYSTEM (IF EQUIPPED)With the keyless entry keypad, youcan:• lock or unlock the vehicle doorswithout using the key.• open the trunk.See a
3. Enter a second personal 5-digit code. Each number must be enteredwithin five seconds of each other.4. Press 3 • 4 to store the second personal code
• To release the trunk, enter the factory-set code or personal code(driver door unlocks) and press 5 • 6 within five seconds.After the factory-set cod
• When the ignition is in the 3 (ON) position, the indicator will glow for3 seconds to indicate normal system functionality.If a problem occurs with t
will need two previously programmed coded keys (keys that alreadyoperate your vehicle’s engine) and the new unprogrammed key(s) readilyaccessible for
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
SEATINGAdjustable head restraintsYour vehicle’s seats are equipped with head restraints which arevertically adjustable. The purpose of these head rest
Lift handle to move seat forward orbackward.Pull lever up to adjust seatback.Using the manual recline function (if equipped)Never adjust the driver’s
To adjust the front seatback usingthe manual recliner:• Lift and hold the handle locatedon the side of the seat.• Lean against the seatback toadjust i
Adjusting the power front seats – door mounted controls(if equipped)The controls for the power seats are located on the inside of each frontdoor.Never
Press to move the seat forward orbackward.Press to move the front portion ofthe seat cushion up or down.Press to move the rear portion ofthe seat cush
Seat mounted cup holders and armrest storage compartment(if equipped)Your vehicle is equipped with cupholders in the rear seat armrest. Toaccess the c
How does the Personal Safety System work?The Personal Safety System can adapt the deployment strategy of yourvehicle’s safety devices according to cra
Front passenger sensing systemFor air bags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occ
Front safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly ag
Safety restraints precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injur
Commentaires sur ces manuels