Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 14Entertainment Systems 16AM/FM stereo 16AM/FM stereo with CD 17AM/FM stereo wi
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa
Using the engine block heater (if equipped)An engine block heater warms the engine coolant which aids in startingand heater/defroster performance. Use
Four-wheel anti-lock brake system (ABS)Your vehicle is equipped with an Anti-lock Braking System (ABS). Thissystem helps you maintain steering control
The BRAKE warning lamp willilluminate and will remainilluminated until the parking brakeis released.To release, pull the lever (2).Always set the park
PREPARING TO DRIVE YOUR VEHICLEUtility vehicles have a significantly higher rollover rate thanother types of vehicles.In a rollover crash, an unbelted
When the key is in the ignition and in the OFF position, theautomatic transmission shift lever can be moved from the P(Park) position without the brak
This position locks the transmission and prevents the rear wheels fromturning.To put your vehicle in gear:• Start the engine• Depress the brake pedal•
• Use when driving conditions cause excessive shifting from O/D toother gears. Examples: city traffic, hilly terrain, heavy loads, trailertowing and w
4. Move the gearshift lever to the desired gear, then slowly release theclutch pedal while slowly pressing on the accelerator.During each shift, the c
Reverse1. Make sure that your vehicle is at a complete stop before you shift intoR (Reverse). Failure to do so may damage the transmission.2. Move the
FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED)For important information regarding safe operation of this typeof vehicle, see Preparing to drive your v
It may take a long period of time for the system to detect animproperly installed or properly re-installed fuel filler capdepending on driving and fue
engage while the vehicle is moving; this is normal and should be noreason for concern. Refer to Shifting to/from 4L (4WD Low) for properoperation.Shif
You should either know the terrain or examine maps of the area beforedriving. Map out your route before driving in the area. To maintainsteering and b
If your vehicle gets stuckIf your vehicle gets stuck in mud or snow it may be rocked out byshifting between forward and reverse gears, stopping betwee
4WD Systems4WD (when you select a 4WD mode) uses all four wheels to power thevehicle. This increases traction, enabling you to drive over terrain andr
Mud and waterIf you must drive through highwater, drive slowly. Traction orbrake capability may be limited.When driving through water,determine the de
slopes or hills. A danger lies in losing traction, slipping sideways andpossibly rolling over. Whenever driving on a hill, determine beforehandthe rou
Should you start to slide while driving on snowy or icy roads, turn thesteering wheel in the direction of the slide until you regain control.Avoid sud
Tires can be damaged during off-road use. For your safety, tires that aredamaged should not be used for highway driving because they are morelikely to
Failure to maintain your vehicle properly may void the warranty, increaseyour repair cost, reduce vehicle performance and operational capabilitiesand
Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue loador king pin w
Safety belt: Reminds you to fastenyour safety belt. A chime will alsosound to remind you to fasten yoursafety belt.Charging system: Illuminates whenth
GVW (Gross Vehicle Weight) – is the Vehicle Curb Weight + cargo +passengers.GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury.Special loading instructions for ow
4x2 w/manual transmissionEngine Rear axleratioMaximumGCWR - lbs.(kg)Maximumtrailerweight - lbs.(kg)Maximumfrontal areaof trailer -ft2(m2)Regular Cab w
4x2 w/manual transmissionEngine Rear axleratioMaximumGCWR - lbs.(kg)Maximumtrailerweight - lbs.(kg)Maximumfrontal areaof trailer -ft2(m2)For definitio
4x4 w/manual transmissionEngine Rear axleratioMaximumGCWR - kg(lbs.)Maximumtrailerweight - kg(lbs)Maximumfrontal areaof trailer -m2(ft2)4.0L(withFX4pa
4x2 w/automatic transmissionEngine Rear axleratioMaximumGCWR - lbs.(kg)Maximumtrailerweight - lbs.(kg)Maximumfrontal areaof trailer -ft2(m2)3.0LEdgeAl
4x4 w/automatic transmissionEngine Rear axleratioMaximumGCWR - kg(lbs.)Maximumtrailerweight - kg(lbs.)Maximumfrontal areaof trailer -m2(ft2)Regular Ca
Do not exceed the GVWR or the GAWR specified on thecertification label.Towing trailers beyond the maximum recommended gross trailerweight exceeds the
Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s brake system. Your vehicle may not have enoughbraking power and your chanc
Four wheel drive low (ifequipped): Illuminates whenfour-wheel drive low is engaged.Four wheel drive high (ifequipped): Illuminates whenfour-wheel driv
Refer to the following chart for information regarding thefactory-equipped trailer tow connector:Trailer tow connectorColor Function Comment1. Dark Gr
Servicing after towingIf you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your Scheduled Maint
Exceeding these limits may allow water to enter vehicle components:• causing internal damage to the components.• affecting driveability, emissions and
Vehicles equipped with automatic transmission and 4x4 vehiclesequipped with an electronic-shift transfer case and a manualtransmission:4x2 vehicles wi
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
This switch is located under theright-hand side of the glove box,just above the carpet.To reset the switch:1. Turn the ignition OFF.2. Check the fuel
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey ———3A Violet Vio
The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 5A Instrument panel dimmer switch2 10A Tra
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description11 10A Smart Junction Box (SJB) (Logicpower)12 15A Center console subwoofer
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description31 20A Front park lamps, Rear parklamps, License plate lamps32 5A Brake swi
2.3L engine (if equipped)The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 50A** Interior
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription14 — Not used15 30A** Anti-lock Brake System (ABS)(solenoids)16 — Not used17 40A** AB
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription41 15A* Heated Exhaust Gas Oxygen(HEGO) sensors, EVAP canistervent valve, Exhaust Gas
3.0L and 4.0L engines (if equipped)The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 50A*
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription14 — Not used15 30A** Anti-lock Brake System (ABS)(solenoids)16 — Not used17 40A** AB
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription41 15A* Heated Exhaust Gas Oxygen(HEGO) sensors, EVAP canistervent valve, Exhaust Gas
T-Type/Mini-Spare Tire InformationYour vehicle may be equipped with a T-type/mini-spare tire. This tire willhave the words “Temporary Use Only” molded
Your vehicle may be equipped with a dissimilar spare tire/wheel. Adissimilar spare tire/wheel is defined as a spare tire and/or wheel that isdifferent
Location of the spare tire and toolsThe spare tire and tools for your vehicle are stowed in the followinglocations:Tool LocationSpare tire Under the v
Trip odometer: Registers thekilometers (miles) of individualjourneys. Press the button onceuntil “TRIP” appears in the display(this represents the tri
2. If equipped, unlock and removethe spare tire carrier lock from therear access hole located just abovethe rear bumper and below thetailgate.3. Inser
If the vehicle slips off the jack, you or someone else could beseriously injured.1. Park on a level surface, activatehazard flashers and place gearshi
• Front• RearTo lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engine when
10. Remove the jack and fullytighten the lug nuts, in the ordershown. Refer to Wheel lug nuttorque specifications later in thischapter for the proper
Lug nut socketsize/Bolt sizeWheel lug nut torque*lb.ft. N•mLug nut socket size:3⁄4” (19 mm) hexBolt size:1⁄2x20100 135* Torque specifications are for
2. Do not disconnect the battery of the disabled vehicle as this coulddamage the vehicle’s electrical system.3. Park the booster vehicle close to the
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
AM/FM STEREO (IF EQUIPPED)1. AM/FM: Press to selectAM/FM1/FM2 frequency bands.2. CLK: Press until SELECT HOUR/ SELECT MINS appears.PressAUDIO to adjus
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli
Ford Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf you own a Lincoln vehicle and are away f
In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or
What kinds of cases does the Board review?Unresolved warranty repair concerns or vehicle performance concerns ason Ford and Lincoln Mercury cars and F
What the Board needsTo have your case reviewed you must complete the application in theDSB brochure and mail it to the address provided on the applica
Every effort is made to decide the case within 40 days of the date thatall requested information is received by the Board. Since the Boardgenerally me
parties, make decisions and, when appropriate, render awards to resolvedisputes. CAMVAP decisions are fast, fair, and final; the arbitrator’saward is
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
3. The vehicle is out of service for repair of nonconformities for a total ofmore than 30 calendar days (not necessarily all at one time)In the case o
4. Tune: Press to manually go down/up ( / ) the radio frequencyand in audio mode to select various settings.5. Memory presets: To set astation: Select
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam
• 2.3L I4 engine• 3.0L V6 engine2004 Ranger (ran)Owners Guide (post-2002-fmt)USA English (fus)Cleaning172
• 4.0L SOHC V6 engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTIC (NON-PAINTED)
• Avoid cleaners or polish that increase the gloss of the upper portion ofthe instrument panel. The dull finish in this area helps protect thedriver f
Note: In some instances, color or dye transfer can occur when wetclothing comes in contact with leather upholstery. If this occurs, theleather should
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
Working with the engine on• Automatic transmission:1. Set the parking brake and shift to P (Park).2. Block the wheels.• Manual transmission:1. Set the
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.3L I4 engine1. Windshield washer fluid reservoir2. Engine coolant reservoir3. Engine oil dipstick4.
3.0L V6 engine1. Engine coolant reservoir2. Windshield washer fluid reservoir3. Engine oil filler cap4. Automatic transmission fluid dipstick (if equi
1. CD eject: Press to eject the CD.2. CLK (Clock):Press CLK untilSELECT HOUR or SELECT MINS isdisplayed. PressTUNE to adjust thehours/minutes. Press C
4.0L SOHC V6 engine1. Windshield washer fluid reservoir2. Automatic transmission fluid dipstick (if equipped)3. Engine oil filler cap4. Engine oil dip
WINDSHIELD WASHER FLUID• 2.3L engine• 3.0L and 4.0L enginesAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the re
If you operate your vehicle in temperatures below 4.5° C (40°F), use washer fluid with antifreeze protection. Failure to usewasher fluid with antifree
• 2.3L I4 engine• 3.0L V6 engineMAXMIN2004 Ranger (ran)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specifications183
• 4.0L SOHC V6 engine6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.• If the oil level is between the MIN and MAX marks,
• 2.3L I4 engine• 3.0L V6 engine2004 Ranger (ran)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specifications185
• 4.0L SOHC V6 engine• Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician.7. Put t
Engine Oil Recommendations2.3L & 3.0L EnginesLook for this certificationtrademark.Use SAE 5W-20 engine oil.Only use oils “Certified For Gasoline E
Use SAE 5W-30 engine oil.Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). To protect your engine’s warranty us
If the electrolyte level in the battery is low, you can add plain tap waterto the battery, as long as you do not use hard water (water with a highmine
6. SHUFF (Shuffle): Press to playthe tracks on the current CD inrandom order.7. REPEAT: Press to repeat thecurrent CD track. The selection willrepeat
Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe bat
ENGINE COOLANTChecking engine coolantThe concentration and level of engine coolant should be checked at themileage intervals listed in the Scheduled M
• 3.0L and 4.0L enginesWhen the engine is cold, check the level of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD
Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur
remove the coolant pressure relief cap on the radiator of a vehicle withan overflow system, follow these steps to add engine coolant.Note: The 3.0L an
Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut
What you should know about fail-safe cooling (2.3L I4 engine only)If the engine coolant supply is depleted, this feature allows the vehicle tobe drive
Never remove the coolant reservoir cap while the engine isrunning or hot.5. Restart the engine and take your vehicle to a service facility.Driving the
Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforefueling your vehicle.• Alwa
Use the following guidelines to avoid static build-up when filling anungrounded fuel container:• Place approved fuel container on the ground.• DO NOT
Seating and Safety Restraints 60Seating 60Safety restraints 62Air bags 73Child restraints 83Driving 96Starting 96Brakes 100Transmission operation 103V
15. CD: Press to enter CD mode. Ifa CD is already present in thesystem, the disc will begin to play.16. CD slot: Insert a CD label sideup.CD units are
Choosing the right fuelUse only UNLEADED FUEL. The use of leaded fuel is prohibited by lawand could damage your vehicle.Your vehicle was not designed
Many of the world’s automakers approved the World-wide Fuel Charterthat recommends gasoline specifications to provide improvedperformance and emission
Filling the tankThe advertised fuel capacity of the fuel tank on your vehicle is equal tothe rated refill capacity of the fuel tank as listed in the R
5. Follow one of the simple calculations in order to determine fueleconomy:Calculation 1: Multiply liters used by 100, then divide by totalkilometers
Maintenance• Keep tires properly inflated and use only recommended size.• Operating a vehicle with the wheels out of alignment will reduce fueleconomy
EMISSION CONTROL SYSTEMYour vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to co
Please consult your Warranty Guide for complete emission warrantyinformation.On board diagnostics (OBD-II)Your vehicle is equipped with a computer tha
• Next, at least 20 minutes driving in stop-and-go, city-type traffic withat least four idle periods.Allow the vehicle to sit for at least eight hours
• 4.0L V6 engineCheck the power steering fluid. Refer to the scheduled maintenanceguide for the service interval schedules. If adding fluid is necessa
BRAKE FLUID RESERVOIRThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels below the “M
1. CD eject: Press to eject the CD.2. CLK (Clock): Press CLK untilSELECT HOUR or SELECT MINS isdisplayed. PressMENU toadjust the hours/minutes.Press C
1. Clean the reservoir cap beforeremoval to prevent dirt and waterfrom entering the reservoir.2. Remove cap and rubberdiaphragm from reservoir.3. Add
8. Remove the dipstick and inspectthe fluid level. Level should be inthe cross-hatched area.9. If necessary, add fluid in 250ml (1/2 pint) increments
Checking and adding manual transmission fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Fluid leve
Checking and adding transfer case fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough
AIR FILTER MAINTENANCERefer to the scheduled maintenance guide for the appropriate intervalsfor changing the air filter element.When changing the air
Note: Failure to use the correct air filter element may result in severeengine damage. The customer warranty may be voided for any damage tothe engine
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
Increasing the inflation pressure beyond this pressure will not increasethe tires load carrying capability.• kPa: Kilopascal, a metric unit of air pre
3. 65: Indicates the aspect ratio which gives the tire’s ratio of height towidth.4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or ri
8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n
Track number/music name/file name: In MP3 mode, pressMENU to view by track number, music name or file name.Dolby:Dolby威 noise reduction: Reduces tape
13. Maximum Permissible Inflation Pressure: Tire manufacturer’smaximum permissible pressure and/or the pressure at which themaximum load can be carrie
Information on “T” type tiresT145/80D16 is an example of a tiresize.Note: The temporary tire size foryour vehicle may be different thanthis example.1.
Use the recommended cold inflation pressure for optimum tireperformance and wear. Under-inflation or over-inflation may causeuneven treadwear patterns
6. Visually inspect the tires to make sure there are no nails or otherobjects embedded that could poke a hole in the tire and cause an airleak.7. Chec
• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive (4WD)vehicles (front tires at top of
Sometimes irregular tire wear can be corrected by rotating the tires.Note: If your tires show uneven wear ask a qualified technician at aFord or Linco
• Severe abrasion on the sidewallIf your vehicle has a leak in the exhaust system, a road tire or the sparetire may be exposed to hot exhaust temperat
Tire explosions can cause death, personal injury or propertydamage. Do not allow anyone to stand near, directly ahead orbehind the spinning tire.Never
• Install chains securely, verifying that the chains do not touch anywiring, brake lines or fuel lines.• Drive cautiously. If you hear the chains rub
Replace the spark plugs with ones that meet Ford material anddesign specifications for your vehicle, such as Motorcraft orequivalent replacement parts
13. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, press andhold a preset button until sound returns. To select a pre
Fluid Ford PartNameApplication CapacityTransmissionfluid1MotorcraftMERCON威 ATF5-speed manual 2.65L (2.8quarts)3MotorcraftMERCON威VATF4x2 vehicleswith a
Fluid Ford PartNameApplication CapacityFuel tank N/A Regular cab(Short wheelbase)64.4L (17gallons)Regular cab(Long wheelbase)76.8L (20.3gallons)SuperC
2Indicates only approximate dry-fill capacity. Some applications may varybased on cooler size and if equipped with an in-tank cooler. The amountof tra
ItemFord partname orequivalentFord partnumberFordspecificationBrake fluid andclutch fluid (ifequipped)Motorcraft HighPerformanceDOT 3 MotorVehicle Bra
ItemFord partname orequivalentFord partnumberFordspecificationTransmission/steering/parkingbrake linkagesand pivots,brake andclutch pedalshaft, clutch
ENGINE DATAEngine 2.3L I4 engine 3.0L V6 engine 4.0L V6 engineCubic inches 138 182 245Required fuel 87 octane 87 octane 87 octaneFiring order 1-3-4-2
412004 Ranger (ran)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specifications236
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea
TRUCK APPLICATION:Code Transmission DescriptionManual transmissionM Manual 5–speed (AKK))C Manual 5–speed overdrive (Close ratio)W Manual 5–speed over
become jammed. It is recommended that homemade CDs beidentified with permanent felt tip marker rather than adhesivelabels. Ballpoint pens may damage C
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford
Splash guardsStep barsTonneau coversTruck capsWheelsInterior styleCell phone holdersConsolesElectrochromatic compass/temperature interior mirrorsFloor
Peace of mindAirbag anti-theft locksFirst aid and safety kitsFull vehicle coversLocking gas capNavigation systemsRemote startVehicle security systemsF
AAir bag supplemental restraintsystem ...73–74and child safety seats ...75description ...
wiper blades ...173Clock adjustAM/FM Stereo ...16AM/FM stereo CD...18AM/FM stereo t
specifications ...232, 235Exhaust fumes ...100FFail safe cooling ...196Fluid capacities ...
storage ...146, 148–149Jump-starting your vehicle ...154KKeyspositions of the ignition ...96LLampsbulb replacementspecifi
Safety belts (see Safetyrestraints) ...62, 64–66Safety defects, reporting ...169Safety restraints ...62, 64–66b
Vehicle Identification Number(VIN) ...238Vehicle loading ...118camper bodies ...
5. MUTE: Press to mute the playingmedia. Press again to return to theplaying media.6. MENU: Press MENU repeatedlyto toggle through the followingmodes
9. SHUFF (Shuffle): Press to playthe tracks on the current CD/MP3 inrandom order. In MP3 directorymode, press to play the tracks within the current di
18. LOAD: Press to load a CD. Press and hold to autoload up to sixdiscs.19. CD slot: Insert a CD, label side up.CD units are designed to play commerci
2. CD: Press to enter CD mode. If aCD is already present in the system,the disc will begin play.3. CLK (Clock): Press CLK untilSELECT HOUR/SELECT MINU
TREB (treble): Press TUNE to decrease/increase the treblelevels.BAL (Balance):PressTUNE to adjust the audio between theleft and right speakers.FADE: P
Maintenance and Specifications 176Engine compartment 178Engine oil 182Battery 188Fuel information 197Air filter(s) 214Tire Information 216Part numbers
14. MUTE: Press to mute theplaying media. Press again to returnto the playing media.15. REW (rewind): Press tomanually reverse a CD track.16. SEEK: In
RADIO RECEPTION FACTORSThere are three factors that can affect radio reception:• Distance/strength: The further you travel from an FM station, theweak
Don’t:• Expose discs to direct sunlight or heat sources for extended periodsof time.• Insert more than one disc into each slot of the CD changer magaz
HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe
To aid in side window defogging/demisting in cold weather:1. Select.2. Adjust the temperature control to maintain comfort.3. Set the fan speed to the
OPERATING TIPS• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
HEADLAMP CONTROLTurns the lamps off.Turns on the parkinglamps, instrument panel lamps,license plate lamps and tail lamps.Turns the headlamps on.Foglam
High beamsPush the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate.Flash to passPull toward you slightly to acti
HEADLAMP AIM ADJUSTMENTThe headlamps on your vehicle can only be vertically adjusted. Yourvehicle does not require horizontal aim adjustments.To adjus
6. In addition to the horizontal linemarked in step 2, a pair of verticallines (5) must be marked at thecenter line of the headlamps on thewall or scr
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
BULBSReplacing exterior bulbsCheck the operation of all the bulbs frequently.Using the right bulbsReplacement bulbs are specified in the chart below.
Replacing headlamp bulbsTo remove the headlamp bulb:1. Make sure the headlamp switch isin the OFF position, then open thehood.2. Remove two screws and
Replacing front side marker /turn signal/ sidemarker bulbs1. Turn the headlamp switch to theOFF position and then open thehood.2. Remove two screws an
Replacing tail lamp/backup lamp bulbs1. Make sure the headlamp switch isin the OFF position and the openthe tailgate to expose the lampassemblies.2. R
Replacing foglamp bulbs (if equipped)1. Make sure the headlamp switch isin the OFF position and remove thebulb socket from the foglamp byturning count
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers(from desired interval to low or hi
TILT STEERING WHEEL (IF EQUIPPED)To adjust the steering wheel:1. Pull and hold the steering wheelrelease control toward you.2. Move the steering wheel
POWER WINDOWS (IF EQUIPPED)When closing the powerwindows, you should verifythey are free of obstructions andensure that children and/or petsare not in
FOLD-AWAY MIRRORSPull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.SPEED CONTROL (IF EQUIPPED)With spee
• If the vehicle speed decreases to 30 mph (48 km/h) or less, yourspeed control will disengageDisengaging speed controlTo disengage the speed control:
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury and prevent possibledamage to others, you
• Depress the brake pedal or theclutch pedal (if equipped) untilthe desired vehicle speed isreached, press the SET + control.Turning off speed control
Mobile Communication Equipment includes, but is not limited to cellularphones, pagers, portable email devices, in vehicle communicationssystems, telem
4. Evenly push down on theextender and push the round knobsin on each side locking it in place.Green markings on the shaftindicate the locked position
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
Your vehicle is equipped with a remote entry system which allows you to:• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta
To replace the battery:1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIR
To reprogram the remote entrytransmitters:1. Ensure the vehicle iselectronically unlocked.2. Put the key in the ignition.3. Turn the key from the 2 (L
SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEMSecuriLock娂 passive anti-theft system is an engine immobilizationsystem. This system is designed to prevent the e
Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 3(OFF) position.The theft indicator will flash everytwo seconds wh
Tips:• A maximum of eight keys can be coded to your vehicle.• Only use Securilock娂 keys.• You must have two previously programmed coded keys (keys tha
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
60/40 seat (if equipped)To gain access to the storagecompartment in your armrest (ifequipped), lift the latch to open lid.The 60/40 seat cupholder (if
To return seat to original position, slide the seat bottom back, then pushthe seatback up to lock it in place. The seat will lock, and you will haveto
Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.All
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
This mode should be used any time a child safety seat is installed in apassenger front seat. Refer to Safety restraints for children or Safetyseats fo
BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe safety belt assembly “automatic locking retractor” feature orany other safety belt function is not
• Regular Cab and 4–door SuperCab• 2–door SuperCabTo lower the shoulder belt height, push the button and slide the heightadjuster down. To raise the h
Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignition switchis turned to the ON position...The safety belt wa
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental restraint
The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to infla
To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle.BeltMinder activation and deactivation proce
Safety belt maintenanceInspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to ma
Important supplemental restraint system (SRS) precautionsThe supplemental restraint system is designed to work with the safetybelt to help protect the
Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause thoseobjects to be propelled by the
Never place a rearward facing child safety restraint in front of anactivated airbag. Airbags have been known to kill or injurechildren in front facing
How does the air bag supplemental restraint system work?The air bag SRS is designed toactivate when the vehicle sustainssufficient longitudinal decele
If the air bag has deployed, the air bag will not functionagain and must be replaced immediately. If the air bag is notreplaced, the unrepaired area w
Disposal of air bags and air bag equipped vehicles (includingpretensioners)See your local dealership or qualified technician. Air bags MUST BEdisposed
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
In order to avoid inadvertent activation of the switch, alwaysremove the ignition key from the passenger air bag ON/OFFswitch.Turning the passenger ai
The vast majority of drivers and passengers are much safer with an airbag than without. To do their job and reduce the risk of life threateninginjurie
3. Medical condition. A passenger has a medical condition which,according to his or her physician:• causes the passenger air bag to pose a special ris
3. Medical condition: A passenger has a medical condition that,according to his or her physician:• poses a special risk for the passenger if the air b
Do not install a child seat in a center facing jump seat.Children and safety beltsIf the child is the proper size, restrain the child in a safety seat
Booster seats should be used until you can answer YES to ALL of thesequestions:• Can the child sit all the way backagainst the vehicle seat back withk
The shoulder belt should cross the chest, resting snugly on the center ofthe shoulder. The lap belt should rest low and snug across the hips,never up
When installing a child safety seat:• Review and follow the informationpresented in the Air bagsupplemental restraint system(SRS) section in this chap
Installing child safety seats with combination lap and shoulderbelts1. Position the child safety seat in aseat with a combination lap andshoulder belt
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with knee on thechild seat.8. Al
The tether strap anchors in your vehicle are in the following positions(shown from top view):• Bucket seats• 60/40 seatsAttach the tether strap only t
3. Locate the correct anchor for the selected seating position.The tether anchor is located on therear lower portion of the passengerseat.4. Clip the
Center seating locationWhen installing a child safety seat in the front center position, route thetether strap over the center arm rest and clip it to
Attaching safety seats with LATCH (Lower Anchors and Tethers forChildren) attachments for child seat anchorsSome child safety seats have two rigid or
The lower anchors for child seatinstallation are located at the rearsection of the front passenger seatbetween the cushion and seat back.The LATCH anc
STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo
Extended idling at high engine speeds can produce very hightemperatures in the engine and exhaust system, creating the riskof fire or other damage.Do
If starting a vehicle with an automatic transmission:• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).If starting a vehicle
• Turn the key to 4 (ON) withoutturning the key to 5 (START).Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to i
Commentaires sur ces manuels