Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 14Entertainment Systems 16AM/FM stereo 16AM/FM stereo with CD 17AM/FM stereo ta
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa
Using the engine block heater (if equipped)An engine block heater warms the engine coolant which aids in startingand heater/defroster performance. Use
Four-wheel anti-lock brake system (ABS)Your vehicle is equipped with an Anti-lock Braking System (ABS). Thissystem helps you maintain steering control
The BRAKE warning lamp willilluminate and will remainilluminated until the parking brakeis released.To release, pull the lever (2).Always set the park
In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a safety belt.Your vehicle has larger tires and incre
3. Start the vehicle.If it is necessary to use the above procedure to move the gearshift lever,it is possible that a fuse has blown or the vehicle’s b
• Depress the brake pedal• Move the gearshift lever into the desired gearTo put your vehicle in P (Park):• Come to a complete stop• Move the gearshift
• O/D (Overdrive) is automatically returned each time the key is turnedoff.2 (Second)Use 2 (Second) to start-up on slippery roads or to provide additi
shift efforts and prematurely wear components in the transmission. Makesure the floor mat is properly positioned so it doesn’t interfere with thefull
• The gearshift lever can only be moved into R (Reverse) by moving itfrom left of 3 (Third) and 4 (Fourth) before shifting into R (Reverse).This is a
Four–wheel drive (4WD) supplies power to all four wheels. 4WD shouldnot be operated on dry pavement; driveline damage may occur.If equipped with the E
It may take a long period of time for the system to detect animproperly installed or properly re-installed fuel filler capdepending on driving and fue
Note: Do not perform this operation if the rear wheels are slipping.Shifting to/from 4X4 LOW (4WD Low)Note: Some noise may be heard as the 4WD system
• Drive slower in strong crosswinds which can affect the normal steeringcharacteristics of your vehicle.• Be extremely careful when driving on pavemen
Do not spin the wheels at over 56 km/h (35 mph). The tires mayfail and injure a passenger or bystander.Emergency maneuvers• In an unavoidable emergenc
Power is supplied to all four wheelsthrough a transfer case. On 4WDvehicles, the transfer case allowsyou to select 4WD when necessary.Information on t
Be cautious of sudden changes in vehicle speed or direction when youare driving in mud. Even 4WD vehicles can lose traction in slick mud. Aswhen you a
When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This r
Avoid sudden braking as well. Although a 4WD vehicle may acceleratebetter than a two-wheel drive vehicle in snow and ice, it won’t stop anyfaster, bec
You should carefully observe the recommended tire inflation pressurefound on the safety compliance certification label attached to the leftfront door
DRIVING THROUGH WATERIf driving through deep or standing water is unavoidable, proceed veryslowly especially if the depth is not known. Never drive th
Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue loador king pin w
Safety belt: Reminds you to fastenyour safety belt. A chime will alsosound to remind you to fasten yoursafety belt.Charging system: Illuminates whenth
GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).
Maximum Loaded Trailer Weight – is the highest possible weight of afully loaded trailer the vehicle can tow. It assumes a vehicle with onlymandatory o
Calculating the load your vehicle can carry/tow1. Use the appropriate maximum GCWR chart (in the Trailer towingsection in this chapter) for your type
4x2 w/manual transmissionEngine Rear axleratioMaximumGCWR - kg(lbs.)Maximumtrailerweight - kg(lbs.)Maximumfrontal areaof trailer -m2(ft2)SuperCab2.3L
4x4 w/manual transmissionEngine Rear axleratioMaximumGCWR - kg(lbs.)Maximumtrailerweight - kg(lbs)Maximumfrontal areaof trailer -m2(ft2)Regular Cab w/
4x2 w/automatic transmissionEngine Rear axleratioMaximumGCWR - kg(lbs.)Maximumtrailerweight - kg(lbs.)Maximumfrontal areaof trailer -m2(ft2)Regular Ca
4x2 w/automatic transmissionEngine Rear axleratioMaximumGCWR - kg(lbs.)Maximumtrailerweight - kg(lbs.)Maximumfrontal areaof trailer -m2(ft2)Maximum tr
4x4 w/automatic transmissionEngine Rear axleratioMaximumGCWR - kg(lbs.)Maximumtrailerweight - kg(lbs.)Maximumfrontal areaof trailer -m2(ft2)For high a
HitchesFor towing trailers up to 907 kg (2,000 lb), use a weight carrying hitchand ball which uniformly distributes the trailer tongue loads through t
Using a step bumperThe optional step bumper is equipped with an integral hitch and requiresonly a ball with a 19 mm (3/4 inch) shank diameter. The bum
Four wheel drive low (ifequipped): Illuminates whenfour-wheel drive low is engaged.Four wheel drive high (ifequipped): Illuminates whenfour-wheel driv
Trailer tow connectorColor Function Comment3. Tan/White Tail lamp Relay controlled circuitactivated when the parklamps/headlamps are on.4. White Groun
• After you have traveled 80 km (50 miles), thoroughly check yourhitch, electrical connections and trailer wheel lug nuts.• To aid in engine/transmiss
• The maximum recommended speed is 88 km/h (55 mph).• The maximum recommended distance is unlimited.• The vehicle must be towed in the forward positio
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
This switch is located under theright-hand side of the glove box,just above the carpet.To reset the switch:1. Turn the ignition OFF.2. Check the fuel
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey ———3A Violet Vio
The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 5A Instrument panel dimmer switch2 10A Tra
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description11 10A Smart Junction Box (SJB) (Logicpower)12 15A Center console subwoofer
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description31 20A Front park lamps, Rear parklamps, License plate lamps32 5A Brake swi
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
2.3L engine (if equipped)The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 50A** Interior
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription14 — Not used15 30A** Anti-lock Brake System (ABS)(solenoids)16 — Not used17 40A** AB
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription41 15A* Heated Exhaust Gas Oxygen(HEGO) sensors, EVAP canistervent valve, Exhaust Gas
3.0L and 4.0L engines (if equipped)The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 50A*
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription14 — Not used15 30A** Anti-lock Brake System (ABS)(solenoids)16 — Not used17 40A** AB
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription41 15A* Heated Exhaust Gas Oxygen(HEGO) sensors, EVAP canistervent valve, Exhaust Gas
T-Type/Mini-Spare Tire InformationYour vehicle may be equipped with a T-type/mini-spare tire. This tire willhave the words ⬙Temporary Use Only⬙ molded
use only. This means that if you need to use it, you should replace it assoon as possible with a road tire/wheel that is the same size and type asthe
Location of the spare tire and toolsThe spare tire and tools for your vehicle are stowed in the followinglocations:Tool LocationSpare tire Under the v
2. If equipped, unlock and removethe spare tire carrier lock from therear access hole located just abovethe rear bumper and below thetailgate.3. Inser
Trip odometer: Registers thekilometers (miles) of individualjourneys. Press the button onceuntil “TRIP” appears in the display(this represents the tri
If the vehicle slips off the jack, you or someone else could beseriously injured.1. Park on a level surface, activatehazard flashers and place gearshi
• Front• RearTo lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engine when
10. Remove the jack and fullytighten the lug nuts, in the ordershown, to 135 Nm (100 lb-ft). Notethat these tightening specificationsare for nut and b
Bolt size Wheel lug nut torque*N•m lb-ft1⁄2x 20 136 100* Torque specifications are for nut and bolt threads free of dirt andrust. Use only Ford recomm
4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level.5. Tu
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli
AM/FM STEREO (IF EQUIPPED)1. AM/FM: Press to selectAM/FM1/FM2 frequency bands.2. CLK: Press until SELECT HOUR/ SELECT MINS appears.PressAUDIO to adjus
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or
The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedu
from Ford and Lincoln Mercury dealership management, recognized fortheir business leadership qualities.What the Board needsTo have your case reviewed
Making a decisionBoard members review all available information related to eachcomplaint, including oral presentations, and arrive at a fair and impar
In the CAMVAP program, impartial third-party arbitrators conducthearings at mutually convenient times and places in an informalenvironment. These impa
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
3. The vehicle is out of service for repair of nonconformities for a total ofmore than 30 calendar days (not necessarily all at one time)In the case o
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam
4. Tune: Press to manually go down/up ( / ) the radio frequencyand in audio mode to select various settings.5. Memory presets: To set astation: Select
• 2.3L I4 engine• 3.0L V6 engine2004 Ranger (ran)Owners Guide (post-2002-fmt)USA English (fus)Cleaning170
• 4.0L SOHC V6 engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTIC (NON-PAINTED)
• Avoid cleaners or polish that increase the gloss of the upper portion ofthe instrument panel. The dull finish in this area helps protect thedriver f
UNDERBODYFlush the complete underside of your vehicle frequently. Keep body anddoor drain holes free from packed dirt.FORD, LINCOLN AND MERCURY CAR CA
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
Working with the engine on• Automatic transmission:1. Set the parking brake and shift to P (Park).2. Block the wheels.• Manual transmission:1. Set the
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT2.3L I4 engine1. Windshield washer fluid reservoir2. Engine coolant reservoir3. Engine oil dipstick4.
3.0L V6 engine1. Engine coolant reservoir2. Windshield washer fluid reservoir3. Engine oil filler cap4. Automatic transmission fluid dipstick (if equi
4.0L SOHC V6 engine1. Windshield washer fluid reservoir2. Automatic transmission fluid dipstick (if equipped)3. Engine oil filler cap4. Engine oil dip
WINDSHIELD WASHER FLUID• 2.3L engine• 3.0L and 4.0L enginesAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the re
1. CD eject: Press to eject the CD.2. CLK (Clock):Press CLK untilSELECT HOUR or SELECT MINS isdisplayed. PressTUNE to adjust thehours/minutes. Press C
If you operate your vehicle in temperatures below 4.5° C (40°F), use washer fluid with antifreeze protection. Failure to usewasher fluid with antifree
• 2.3L I4 engine• 3.0L V6 engineMAXMIN2004 Ranger (ran)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specifications181
• 4.0L SOHC V6 engine6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.• If the oil level is between the MIN and MAX marks,
• 2.3L I4 engine• 3.0L V6 engine2004 Ranger (ran)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specifications183
• 4.0L SOHC V6 engine• Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician.7. Put t
Engine Oil Recommendations2.3L & 3.0L EnginesLook for this certificationtrademark.Use SAE 5W-20 engine oil.Only use oils “Certified For Gasoline E
Use SAE 5W-30 engine oil.Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). To protect your engine’s warranty us
If the electrolyte level in the battery is low, you can add plain tap waterto the battery, as long as you do not use hard water (water with a highmine
Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe bat
ENGINE COOLANTChecking engine coolantThe concentration and level of engine coolant should be checked at themileage intervals listed in the Scheduled M
6. SHUFF (Shuffle): Press to playthe tracks on the current CD inrandom order.7. REPEAT: Press to repeat thecurrent CD track. The selection willrepeat
• 3.0L and 4.0L enginesWhen the engine is cold, check the level of the engine coolant in thereservoir.• The engine coolant should be at the “cold fill
Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur
coolant pressure relief cap on the radiator of a vehicle with an overflowsystem, follow these steps to add engine coolant.Note: The 3.0L and 4.0L V6 e
Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut
What you should know about fail-safe cooling (2.3L I4 engine only)If the engine coolant supply is depleted, this feature allows the vehicle tobe drive
Never remove the coolant reservoir cap while the engine isrunning or hot.5. Restart the engine and take your vehicle to a service facility.Driving the
Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforefueling your vehicle.• Alwa
The flow of fuel through a fuel pump nozzle can produce staticelectricity, which can cause a fire if fuel is pumped into anungrounded fuel container.U
The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stopsbefore completely rem
It should not be necessary to add any aftermarket products to your fueltank if you continue to use high quality fuel of the recommended octanerating.
Seating and Safety Restraints 60Seating 60Safety restraints 62Air bags 73Child restraints 83Driving 96Starting 96Brakes 100Transmission operation 103V
15. CD: Press to enter CD mode. Ifa CD is already present in thesystem, the disc will begin to play.16. CD slot: Insert a CD label sideup.CD units are
ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform
Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in kilometers or miles).2. Each time you fill the tan
• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between third and fourth gear occurs.Unnecessary shifting of this
EPA window stickerEvery new vehicle should have the EPA window sticker. Contact yourdealer if the window sticker is not supplied with your vehicle. Th
Exhaust leaks may result in entry of harmful and potentiallylethal fumes into the passenger compartment.Do not make any unauthorized changes to your v
Readiness for Inspection/Maintenance (I/M) testingIn some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics sys
CHECKING AND ADDING POWER STEERING FLUID• 2.3L I4 engine• 3.0L V6 engine• 4.0L V6 engineDONOTOVERFILLPOWERSTEERINGFLUID2004 Ranger (ran)Owners Guide (
Check the power steering fluid. Refer to the scheduled maintenanceguide for the service interval schedules. If adding fluid is necessary, useonly MERC
Brake fluid is toxic. If brake fluid contacts the eyes, flush eyeswith running water for 15 minutes. Seek medical attention ifirritation persists. If
5. Shift to P (Park) and leave the engine running.6. Remove the dipstick, wipe clean with a dry lint free rag.7. Install and fully seat the dipstick i
1. CD eject: Press to eject the CD.2. CLK (Clock): Press CLK untilSELECT HOUR or SELECT MINS isdisplayed. PressMENU toadjust the hours/minutes.Press C
Checking and adding manual transmission fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Fluid leve
Checking and adding transfer case fluid (if equipped)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough
AIR FILTER MAINTENANCERefer to the scheduled maintenance guide for the appropriate intervalsfor changing the air filter element.When changing the air
Note: Failure to use the correct air filter element may result in severeengine damage. The customer warranty may be voided for any damage tothe engine
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
• kPa: Kilopascal, a metric unit of air pressure.• PSI: Pounds per square inch, a standard unit of air pressure.• B-pillar: The structural member at t
4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new
8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n
13. Maximum Permissible Inflation Pressure: Tire manufacturesmaximum permissible pressure and/or the pressure at which themaximum load can be carried
Information on “T” type tiresT145/80D16 is an example of a tiresize.Note: The temporary tire size foryour vehicle may be different thanthis example.1.
Track number/music name/file name: In MP3 mode, pressMENU to view by track number, music name or file name.Dolby:Dolby威 noise reduction: Reduces tape
Use the recommended cold inflation pressure for optimum tireperformance and wear. Under-inflation or over-inflation may causeuneven treadwear patterns
6. Visually inspect the tires to make sure there are no nails or otherobjects embedded that could poke a hole in the tire and cause an airleak.7. Chec
• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive (4WD)vehicles (front tires at top of
Sometimes irregular tire wear can be corrected by rotating the tires.Note: If your tires show uneven wear ask a qualified technician at aFord or Linco
• Severe abrasion on the sidewallIf your vehicle has a leak in the exhaust system, a road tire or the sparetire may be exposed to hot exhaust temperat
Tire explosions can cause death, personal injury or propertydamage. Do not allow anyone to stand near, directly ahead orbehind the spinning tire.Never
• Install chains securely, verifying that the chains do not touch anywiring, brake lines or fuel lines.• Drive cautiously. If you hear the chains rub
Replace the spark plugs with ones that meet Ford material anddesign specifications for your vehicle, such as Motorcraft orequivalent replacement parts
Fluid Ford PartNameApplication CapacityTransmissionfluid1MotorcraftMERCON威 ATF5-speed manual 2.65L (2.8quarts)3MotorcraftMERCON威VATF4x2 vehicleswith a
Fluid Ford PartNameApplication CapacityFuel tank N/A Regular cab(Short wheelbase)64.4L (17gallons)Regular cab(Long wheelbase)76.8L (20.3gallons)SuperC
13. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, press andhold a preset button until sound returns. To select a pre
of transmission fluid and fluid level should be set by the indication onthe dipstick’s normal operating range.3Service refill capacity for the manual
ItemFord partname orequivalentFord partnumberFordspecificationBrake fluid andclutch fluid (ifequipped)Motorcraft HighPerformanceDOT 3 MotorVehicle Bra
ItemFord partname orequivalentFord partnumberFordspecificationTransmission/steering/parkingbrake linkagesand pivots,brake andclutch pedalshaft, clutch
ENGINE DATAEngine 2.3L I4 engine 3.0L V6 engine 4.0L V6 engineCubic inches 138 182 245Required fuel 87 octane 87 octane 87 octaneFiring order 1-3-4-2
412004 Ranger (ran)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specifications234
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea
TRUCK APPLICATION:Code Transmission DescriptionManual transmissionM Manual 5–speed (AKK))C Manual 5–speed overdrive (Close ratio)W Manual 5–speed over
PASSENGER CAR APPLICATION:Code Transmission/Transaxle DescriptionFront wheel drive manual transaxleR5–speed overdrive (MTX75)W5–speed overdrive (M5)Fr
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford
CD units are designed to play commercially pressed 12 cm (4.75in) audio compact discs only. Due to technical incompatibility,certain recordable and re
Splash guardsStep barsTonneau coversTruck capsWheelsInterior styleCell phone holdersConsolesElectrochromatic compass/temperature interior mirrorsFloor
Peace of mindAirbag anti-theft locksFirst aid and safety kitsFull vehicle coversLocking gas capNavigation systemsRemote startVehicle security systemsF
AAir bag supplemental restraintsystem ...73and child safety seats ...75description ...
waxing ...168wheels ...169wiper blades ...171Clock adjus
specifications ...230, 233Exhaust fumes ...100FFail safe cooling ...194Fluid capacities ...
storage ...145, 147–148Jump-starting your vehicle ...153KKeyspositions of the ignition ...96LLampsbulb replacementspecifi
Safety defects, reporting ...167Safety restraints ...62, 64–66belt minder ...69extension assembly ...
WWarning lights (see Lights) ...10Washer fluid ...179Water, Driving through ...118Windowspower ...
248
3. EJ (CD eject): Press to eject theCD. Press and hold to eject all CDs.4. CLK (Clock): Press CLK untilSELECT HOUR or SELECT MINS isdisplayed. PressME
Track #/normal music name/file name: Press MENU to access anduse/ to scroll through MP3 display options (track #, normal musicname or file name).7. TU
16. SCAN: In radio, CD and MP3flat file mode, press for a briefsampling of radio stations orCD/MP3 tracks. In MP3 directory mode, press to hear a brie
TREMOR IV CD/MP3 AUDIO SYSTEM (IF EQUIPPED)1. EJ (CD eject): To eject anindividual CD, press CD and selectthe correct slot number by pressingthe Memor
5. TEXT: In MP3 music name/filename mode, press to view the next12 characters in the MP3 musicname/file name of the current MP3 track and directory.6.
Maintenance and Specifications 174Engine compartment 176Engine oil 180Battery 186Fuel information 195Air filter(s) 212Tire Information 214Part numbers
9. ON/OFF/VOL (Volume): Pressto turn the system ON/OFF. Turn toadjust the volume levels.If the volume is set above a certainlevel and the ignition is
17. AM/FM: Press to selectAM/FM1/FM2 frequency band.18. LOAD: To load a CD/MP3 discto a specific slot, press LOAD andselect the slot number by pressin
• Remove loose labels before inserting tapes.• Allow tapes which have been subjected to extreme heat, humidity orcold to reach a moderate temperature
HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe
4. Direct the outer instrument panel vents towards the side windowsTo increase airflow to the outer instrument panel vents, close the ventslocated in
OPERATING TIPS• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
HEADLAMP CONTROLTurns the lamps off.Turns on the parkinglamps, instrument panel lamps,license plate lamps and tail lamps.Turns the headlamps on.Foglam
High beamsPush the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate.Flash to passPull toward you slightly to acti
HEADLAMP AIM ADJUSTMENTThe headlamps on your vehicle can only be vertically adjusted. Yourvehicle does not require horizontal aim adjustments.To adjus
6. Locate the vertical adjuster foreach headlamp. Adjust the aim byturning the adjuster control eitherclockwise (to adjust down) orcounterclockwise (t
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
BULBSReplacing exterior bulbsCheck the operation of all the bulbs frequently.Using the right bulbsReplacement bulbs are specified in the chart below.
Replacing headlamp bulbsTo remove the headlamp bulb:1. Make sure the headlamp switch isin the OFF position, then open thehood.2. Remove two screws and
Replacing front side marker /turn signal/ sidemarker bulbs1. Turn the headlamp switch to theOFF position and then open thehood.2. Remove two screws an
Replacing tail lamp/backup lamp bulbs1. Make sure the headlamp switch isin the OFF position and the openthe tailgate to expose the lampassemblies.2. R
Replacing foglamp bulbs (if equipped)1. Make sure the headlamp switch isin the OFF position and remove thebulb socket from the foglamp byturning count
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers(from desired interval to low or hi
TILT STEERING WHEEL (IF EQUIPPED)To adjust the steering wheel:1. Pull and hold the steering wheelrelease control toward you.2. Move the steering wheel
POWER WINDOWS (IF EQUIPPED)When closing the powerwindows, you should verifythey are free of obstructions andensure that children and/or petsare not in
SPEED CONTROL (IF EQUIPPED)With speed control set, you can maintain a speed of 48 km/h (30 mph)or more without keeping your foot on the accelerator pe
Note: When you use the clutch pedal to disengage the speed control,the engine speed may briefly increase, this is normal.Resuming a set speedPress the
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury and prevent possibledamage to others, you
Turning off speed controlThere are two ways to turn off thespeed control:• Press the speed control OFFcontrol.• Turn OFF the ignition.Note: When you t
A driver’s first responsibility is the safe operation of the vehicle.The most important thing you can do to prevent a crash is toavoid distractions an
4. Evenly push down on theextender and push the round knobsin on each side locking it in place.Green markings on the shaftindicate the locked position
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
Your vehicle is equipped with a remote entry system which allows you to:• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta
To replace the battery:1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIR
To reprogram the remote entrytransmitters:1. Ensure the vehicle iselectronically unlocked.2. Put the key in the ignition.3. Turn the key from the 2 (L
SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEMSecuriLock娂 passive anti-theft system is an engine immobilizationsystem. This system is designed to prevent the e
Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 3(OFF) position.The theft indicator will flash everytwo seconds wh
Tips:• A maximum of eight keys can be coded to your vehicle.• Only use Securilock娂 keys.• You must have two previously programmed coded keys (keys tha
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
60/40 seat (if equipped)To gain access to the storagecompartment in your armrest (ifequipped), lift the latch to open lid.The 60/40 seat cupholder (if
To return seat to original position, slide the seat bottom back, then pushthe seatback up to lock it in place. The seat will lock, and you will haveto
To reduce the risk of injury, make sure children sit where theycan be properly restrained.Never let a passenger hold a child on his or her lap while t
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
This mode should be used any time a child safety seat is installed in apassenger front seat. Refer to Safety restraints for children or Safetyseats fo
BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe safety belt assembly “automatic locking retractor” feature orany other safety belt function is not
• Regular Cab and 4–door SuperCab• 2–door SuperCabTo lower the shoulder belt height, push the button and slide the heightadjuster down. To raise the h
Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignition switchis turned to the ON position...The safety belt wa
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental restraint
The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to infla
To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle.BeltMinder activation and deactivation proce
Safety belt maintenanceInspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to ma
Air bags DO NOT inflate slowly or gently and the risk of injury from adeploying air bag is greatest close to the trim covering the air bagmodule.Never
Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause thoseobjects to be propelled by the
Never place a rearward facing child safety restraint in front of anactivated airbag. Airbags have been known to kill or injurechildren in front facing
How does the air bag supplemental restraint system work?The air bag SRS is designed toactivate when the vehicle sustainssufficient longitudinal decele
If the air bag has deployed, the air bag will not functionagain and must be replaced immediately. If the air bag is notreplaced, the unrepaired area w
Disposal of air bags and air bag equipped vehicles (includingpretensioners)See your local dealership or qualified technician. Air bags MUST BEdisposed
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
In order to avoid inadvertent activation of the switch, alwaysremove the ignition key from the passenger air bag ON/OFFswitch.Turning the passenger ai
The vast majority of drivers and passengers are much safer with an airbag than without. To do their job and reduce the risk of life threateninginjurie
3. Medical condition. A passenger has a medical condition which,according to his or her physician:• causes the passenger air bag to pose a special ris
3. Medical condition: A passenger has a medical condition that,according to his or her physician:• poses a special risk for the passenger if the air b
Do not install a child seat in a center facing jump seat.Children and safety beltsIf the child is the proper size, restrain the child in a safety seat
• Can the child sit all the way backagainst the vehicle seat back withknees bent comfortably at theedge of the seat withoutslouching?• Does the lap be
The shoulder belt should cross the chest, resting snugly on the center ofthe shoulder. The lap belt should rest low and snug across the hips,never up
When installing a child safety seat:• Review and follow the informationpresented in the Air bagsupplemental restraint system(SRS) section in this chap
Installing child safety seats with combination lap and shoulderbelts1. Position the child safety seat in aseat with a combination lap andshoulder belt
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with knee on thechild seat.8. Al
• Bucket seats• 60/40 seatsAttach the tether strap only to the appropriate tether anchor asshown. The tether strap may not work properly if attachedso
The tether anchor is located on therear lower portion of the passengerseat.4. Clip the tether strap to theanchor.2004 Ranger (ran)Owners Guide (post-2
Center seating locationWhen installing a child safety seat in the front center position, route thetether strap over the center arm rest and clip it to
Attaching safety seats with LATCH (Lower Anchors and Tethers forChildren) attachments for child seat anchorsSome child safety seats have two rigid or
The lower anchors for child seatinstallation are located at the rearsection of the front passenger seatbetween the cushion and seat back.The LATCH anc
STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo
Extended idling at high engine speeds can produce very hightemperatures in the engine and exhaust system, creating the riskof fire or other damage.Do
• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).If starting a vehicle with a manualtransmission:1. Make sure the parking b
• Turn the key to 4 (ON) withoutturning the key to 5 (START).Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to i
Commentaires sur ces manuels