Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 15Entertainment Systems 18AM/FM stereo 18AM/FM stereo with CD 20AM/FM stereo wi
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A wa
RelockThe autolock feature repeats when:• an “autolock” occurrence has already taken place,• the brake is depressed while vehicle speed is less than 5
Disassociating the memory feature from the remote transmitterTo deactivate this feature:1. Press the SET control on the driver’s door panel.2. Within
Programming a personal entry codeTo create your own personal entry code(s):1. Enter the factory set code. Note: The driver’s door will unlock.2. Withi
The personal code is now erased and only the factory set 5–digit codewill work.Unlocking and locking the doors using keyless entryTo unlock the driver
3. Turn the ignition key from the 4 (ON) position to the 3 (OFF)position.4. Press the power door unlock control three times.5. Turn the ignition back
The following items may prevent the vehicle from starting:• Large metallic objects.• Electronic devices on the key chain that can be used to purchaseg
Please read and understand the entire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition and turn the igni
PERIMETER ALARM SYSTEM (IF EQUIPPED)The perimeter anti-theft system will warn you in the event of anunauthorized entry to your vehicle.If there is any
SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a
Adjusting the front manual seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving.Always drive and ride with your seat
Check fuel cap: Illuminates whenthe fuel cap may not be properlyinstalled. Continued driving withthis light on may cause the Checkengine warning light
Reclining the seatback can reduce the effectiveness of the seat’ssafety belt in the event of a collision.The control is located on the outboard side o
Using the manual lumbar support (if equipped)The lumbar control is located on theinboard side of the seat under thearmrest.Rotate the control to chang
REAR SEATSHead restraintsLift the head restraint so that it is located directly or as close as possiblebehind your head.The head restraints can be mov
The cupholder is designed to detach from the seat when subjected toheavy load. The cupholder can be reinstalled by returning to the closedposition.Adj
• 2nd row bench seat (if equipped)Note: This seat can be movedforward to keep a child in aLATCH child restraint attachedto the LATCH anchors at thecen
Accessing the third row seat with a second row bucket seatEnsure head restraint is in the fulldown position and seat is adjustedto full rear position
Continuing to lift the handle willtumble the seat forward, allowingeasier access to the third row seat.After entering the 3rd row seat,return the seat
Second row bench seat tip slide feature1. Push the side easy-entry controlhandle forward and allow the seatback to flip forward.2. Push the seat forwa
After exiting the third row, pushrearward on the cushion of the seatto return the seat to its originalposition.Push the seatback rearward until itlatc
4. From inside the vehicle, pull upon front floor release handle(yellow).5. Rotate the seat rearward at a 30to 45 degree angle.6. With the assist hand
Safety belt: Reminds you to fastenyour safety belt. A chime will alsosound to remind you to fasten yoursafety belt.Check transaxle: Illuminates whena
Second row bench seat1. Detach the lap/shoulder beltsfrom both sides of the seat byinserting a seat belt tongue or keyinto the buckle release slot, pu
3. Clip the end of the belt to thestationary portion of the shoulderbelt coming out of the trim panel.The end of the shoulder belt mustbe clipped in o
1. Position the seat in vehicle. Placefirst row seat in a forward positionto allow the second row seat to beinstalled.2. Install seat onto rear pin of
4. Rotate seat rearward until theback of the seat latches onto thefloor.5. Operate recline lever and pushthe seat back upright.Ensure seat is latched
3. Lower back of seat onto the reartubs until both release controls latchinto place. Be sure that the seat islocked in place both front and back.Do no
2. If you plan to carry very largeobjects or items that might damagethe center lap/shoulder belt, detachthe belt from the seat. Use a key orseat belt
4. Store the belt in the housingfound on the ceiling by inserting thesmaller tongue in the slot provided.Note: The seat can be stowed withthe safety b
Important: If you don’t let go ofthe number 1 strap before the seatback folds completely, the seat maynot stow flat in the tub. Refer to thelabel atta
8. Pull the number 3 strap on the seat back to tumble seat all the way into the tub in the floor.Do not use the seat anchors as cargo tie downs.Unstow
2. To return the seat back to theseating position, pull the number 1strap, then while holding thenumber 1 strap, pull the number 3strap to raise the s
Traction Control娂 or AdvanceTrac娂 active (if equipped):Illuminates when the Traction Control娂 is active, refer to the Drivingchapter for more informat
This is not a position suitable for driving. Do not drive thevehicle with the seat in this position. The safety belts are notfunctional when the seat
3. To return the seat, ensure seatlatching area is free of objects.Then, raise the seat off the liftgatescuff plate and push at the top ofthe seat bac
conditions. A collection of crash and occupant sensors providesinformation to the Restraints control module (RCM). During a crash, theRCM activates th
very close to the air bag. For other occupants, this occurs when theoccupant is not properly restrained by seat belts or child safety seats andthey mo
Front safety belt energy management retractorsThe front outboard safety belt energy management retractors allowwebbing to be pulled out of the retract
Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.All
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
Vehicle sensitive modeThis is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movements and locking in response to
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could re
Low washer fluid: Illuminates when the windshield washer fluid is low.• Without Message Center• With Message CenterDoor ajar: Illuminates when the ign
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignition switchis turned to the ON position...The safety belt wa
If... Then...The driver’s and front passenger’ssafety belts are buckled before theignition switch is turned to the ONposition or less than 1-2 minutes
Reasons given... Consider...“Belts areuncomfortable”We design our safety belts to enhance comfort. Ifyou are uncomfortable - try different positions f
One time disableIf at any time the driver/front passenger quickly buckles then unbucklesthe BeltMinder feature for that seating position, the BeltMind
4. Within 10 seconds of the light turning on, buckle then unbuckle thesafety belt.• This will disable the BeltMinder feature for that seating position
Failure to inspect and if necessary replace the safety beltassembly under the above conditions could result in severepersonal injuries in the event of
Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in
Do not attempt to service, repair, or modify the air bagsupplemental restraint systems or its fuses. See your Ford orLincoln Mercury dealer.Modifying
• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and/or light are repaired.If any of these things ha
force, there is the risk of death or serious injuries such as fractures,facial and eye injuries or internal injuries, particularly to occupants whoare
• With Message CenterDisplays which bulb is burned out.Depress the RESET control to clear.High beams: Illuminates when thehigh beam headlamps are turn
• the front passenger seat is unoccupied,• an infant or small child weighing less than 50 pounds (23 kg) is in thefront seat, either in a child restra
that the person isn’t sitting properly in the seat. If this happens, turn thevehicle off and ask the person to place the seatback in the full uprightp
Do not lean your head on the door. The side air bag could injureyou as it deploys from the side of the seatback.Do not attempt to service, repair, or
The fact that the air bags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of
Do not attempt to service, repair, or modify the Safety Canopy娂system, its fuses, the A, B, C or D pillar trim, or the headliner ona vehicle containin
• Two crash sensors mounted under the front seats (one on each side).• Two crash sensors located at the c-pillar behind the rear doors (oneon each sid
If the Safety Canopy娂system has deployed, theSafety Canopy娂 will notfunction again unless replaced.The Safety Canopy娂 system(including the A, B, C, an
SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Air bag supplem
will provide some protection, these children are still too small forlap/shoulder belts to fit properly, which could increase the risk of seriousinjury
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,
Follow all instructions provided by the manufacturer of thebooster seat.Never put the shoulder belt under a child’s arm or behind theback because it e
• LATCH lower anchors are recommended for use by children up to 22kg (48 pounds) in a child restraint. Top tether anchors can be usedfor children up t
1. Position the child safety seat in aseat with a combination lap andshoulder belt.If you use the 3rd row center seatand the safety belt has beendetac
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly move the seat forwardand back to m
The tether anchors in your vehicleare in the positions shown:The front passenger seat with power adjustment does not have atether anchor. The two teth
2. Route the child safety seat tetherstrap over the back of the seat. Ifthe head restraint is adjustable,route the tether strap under thehead restrain
If the tether strap is clippedincorrectly (as shown) thechild safety seat may not beretained properly in the event of acollision.5. Rotate the tether
Rear seating positionsFollow steps 1–7 as described above for the following available seats:• 2nd row bucket• 2nd row bench• 3rd row benchFor addition
Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol.If your vehicle has a second rowb
Trip odometer: Registers the kilometers (miles) of individual journeys.• Without Message CenterPress and release the button on thecluster to toggle be
Follow the child seat manufacturer’s instructions to properly install achild seat with LATCH attachments.Attach LATCH lower attachments of the child s
STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
• Turn the key to 4 (ON) withoutturning the key to 5 (START).Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to i
1. Turn the key to 5 (START)without pressing the acceleratorpedal and release as soon as theengine starts. The key will return to4 (ON).2. When the en
BRAKESOccasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-o
maximizes the amount of brake booster assist, helping the driver toachieve maximum braking pressure. Once a panic brake application isdetected, the sy
and/or when performing emergency maneuvers. In an emergencylane-change, the driver will experience better overall vehicle traction,and have better con
are allowed to spin. If your vehicle seems to lose engine power whiledriving in deep sand or very deep snow, switching off the AdvanceTrac娂stability e
STEERINGTo prevent damage to the power steering system:• Never hold the steering wheel at its furthest turning points (until itstops) for more than a
AM/FM STEREO SYSTEM (IF EQUIPPED)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various settings.2. Audi
When the key is in the 3 (OFF) position, the automatictransmission shift lever can be moved from the P (Park) positionwithout the brake pedal depresse
Understanding the gearshift positions of the 4–speed automatictransaxleP (Park)This position locks the transaxle and prevents the front wheels fromtur
1 (First)• Transaxle operates in first gear only.• Provides maximum engine braking.• Allows upshifts by moving gearshift lever.• Will not downshift in
To help avoid personal injury, always use caution when in R(Reverse) and when using the RSS.This system is not designed to prevent contact with small
The RSS is automatically enabledwhen the gear selector is placed inR (Reverse) and the ignition is ON.The park aid disable switch allowsthe driver to
your vehicle’s weight ratings, with or without a trailer, from the vehicle’sSafety Certification Label and Tire Label:Base Curb Weight – is the weight
GVW (Gross Vehicle Weight) – is the Vehicle Curb Weight + cargo +passengers.GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the
GCWR (Gross Combined Weight Rating) – is the maximum allowableweight of the vehicle and the loaded trailer – including all cargo andpassengers – that
TRAILER TOWINGYour vehicle is capable either of towing Class I trailers or up to Class IItrailers when equipped with the optional trailer tow package.
Vehicle towing capability/Trailerhitch requirementTrailerModel/EngineGCWR -lbs (kg)Hitch typerequiredTrailer Weightrange - lbs(kg)Tongue loadVan, 3.9L
3. Seek: Press to access thenext/previous strong station ortrack.4. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, pr
HitchesDo not use hitches that clamp onto the vehicle bumper. Use a loadcarrying hitch that does not exceed your vehicle’s capability. See theTongue L
Driving while you towWhen towing a trailer:• Turn off the speed control. The speed control may shut offautomatically when you are towing on long, stee
RECREATIONAL TOWINGFollow these guidelines for your specific powertrain combination to towyour vehicle with all four wheels on the ground (such as beh
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
This switch is located behind theservice panel on the right side ofthe cargo area.To reset the switch:1. Turn the ignition OFF.2. Check the fuel syste
Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey ———3A Violet Vio
To remove a fuse use the fuse puller tool provided on the fuse panelcover.The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPassenger Com
Fuse/RelayLocationFuse AmpRatingPassenger Compartment Fuse PanelDescription13 5A Compass/Driver heated seat/Passengerheated seats/Reverse sensingsyste
To remove the cover of the power distribution box, pull the releaselatches at both ends of the cover, then pull the cover up.The high-current fuses ar
Seating and Safety Restraints 108Seating 108Safety restraints 131Air bags 145Child restraints 157Driving 171Starting 171Brakes 175Transmission operati
AM/FM STEREO/ SINGLE CD SOUND SYSTEM (IF EQUIPPED)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various
Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description14 30A** Front climate control system blower motor15 30A** Right power seat/heated s
Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description52 20A* Trailer tow park lamps53 10A* Heated mirrors54 30A* Front wiper motor55 25A*
Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description66 20A* 2nd row seat power point67 20A* Ignition switch #2 feed70 — Not used71 — Not
Fuse/RelaylocationFuse ampratingDescription8 40A* Left-hand cooling fan motor (Vehicles withtrailer tow package)10A** Low-speed cooling fan circuit br
When driving with the temporary spare tire do not:• use more than one temporary spare tire at a time•exceed 50 mph (80 km/h) or drive further than 2,0
• Use commercial car washing equipment• Use snow chains on the end of the vehicle with the dissimilar sparetire/wheelThe usage of a dissimilar spare t
Removing the jack and tools1. Locate the access panel on the interior trim. Rotate the two panelretaining clips and remove the panel.2. Remove the jac
3. Remove the primary retainer from the center of the tire. Unlock thesecondary (locking) retainer by rotating the top portion one-quarter turnand rem
• Secondary lock in locked positionNote: Do not stow the full size tire or any flat tire under the vehicle.Tire change procedureWhen one of the front
2. Place gearshift lever in P (Park),turn engine off, and block thediagonally opposite wheel.3. Remove the spare tire, jack andlug wrench.4. If equipp
Speed sensitive volume (if equipped): Radio volume automaticallychanges slightly with vehicle speed to compensate for road and windnoise. Press MENU t
If Ford Accessory Running Boardshave been installed, use the jackadapters supplied with the runningboards as described on the inside ofthe jack storag
13. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lug nuttorque specifications later in thischapter for the proper l
4. Check that the flat tire is properly secured.Stowing the spare tireNote: If no tire is to be stowed under the vehicle, attach the secondary(locking
The effort to turn the jack handle increases significantly and the sparetire carrier ratchets or slips when the tire is raised to the maximumtightness
JUMP STARTING YOUR VEHICLEThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury
Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
11. Rewind: Press to manuallyreverse in a CD track.12. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, press andhold a
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedu
from Ford and Lincoln Mercury dealership management, recognized fortheir business leadership qualities.What the Board needsTo have your case reviewed
Making a decisionBoard members review all available information related to eachcomplaint, including oral presentations, and arrive at a fair and impar
In the CAMVAP program, impartial third-party arbitrators conducthearings at mutually convenient times and places in an informalenvironment. These impa
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
3. The vehicle is out of service for repair of nonconformities for a total ofmore than 30 calendar days (not necessarily all at one time)In the case o
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
PREMIUM IN-DASH SIX CD SOUND SYSTEM (IF EQUIPPED)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various
sliding door. If necessary, clean the contacts with Motorcraft Bug andTar Remover (ZC-42) to remove any sealant. Do not use any abrasiveson the contac
• Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all partsthat require cleaning and pressure rinse clean.• Cover the highlighted areas to pr
• Do not use fuel, kerosene, or paint thinner to clean any parts.• Wiper blades can be cleaned with isopropyl (rubbing) alcohol orwindshield washer so
Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing.Do not use chemical solvents or
FORD, LINCOLN AND MERCURY CAR CARE PRODUCTSYour Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect i
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.9L/4.2L V6 engines1. Brake fluid reservoir2. Air filter assembly3. Power distribution box4. Battery5
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
4. Open the hood. Protect yourself from engine heat.5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clea
Speed sensitive volume (if equipped): Radio volume automaticallychanges slightly with vehicle speed to compensate for road and windnoise. Press MENU t
2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler cap
It is recommended you use the appropriate Motorcraft oil filter (oranother brand meeting Ford specifications) for your engine application.BATTERYYour
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a
7. Drive the vehicle to complete the relearning process.• The vehicle may need to be driven 16 km (10 miles) or more torelearn the idle and fuel trim
• Freeze protection down to -36° C (-34° F).• Boiling protection up to 129° C (265° F).• Protection against rust and other forms of corrosion.• Enable
Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservo
For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when
Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium
• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i
swallowed can cause death or permanent injury. If fuel is swallowed,call a physician immediately, even if no symptoms are immediatelyapparent. The tox
11. Rewind: Press to manuallyreverse in a CD track.12. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, press andhold a
• DO NOT use a device that would hold the fuel pump handle in the fillposition.Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1
Your vehicle was not designed to use fuel or fuel additives with metalliccompounds, including manganese-based additives. Studies indicate thatthese ad
Cleaner airFord endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality.Running out of fuelAvoid running out of fuel becaus
amount of fuel in a full tank and a tank when the fuel gauge indicatesempty. Empty reserve is the small amount of fuel remaining in the fueltank after
economy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In gene
• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in your vehicle sche
• Do not turn off the ignition while your vehicle is moving, especially athigh speeds.• Have the items listed in your Scheduled Maintenance Guideperfo
service technician in properly servicing your vehicle. When the Checkengine/Service engine soon light illuminates, the OBD-II system hasdetected a mal
CHECKING AND ADDING POWER STEERING FLUIDCheck the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules. If a
TRANSMISSION FLUIDChecking automatic transmission fluidRefer to your Scheduled Maintenance Guide for scheduled intervals forfluid checks and changes.
20. CD slot: Insert a CD label sideup.AM/FM STEREO CASSETTE/SINGLE CD SOUND SYSTEM(IF EQUIPPED)1./ Tuner: Press tomanually go up or down the radiofreq
The transmission fluid should be inthis range if at normal operatingtemperature (66°C-77°C[150°F-170°F]).High fluid levelFluid levels above the safe r
• Treadwear 200 Traction AA Temperature AThese Tire Quality Grades are determined by standards that the UnitedStates Department of Transportation has
which all passenger car tires must meet under the Federal Motor VehicleSafety Standard No. 109. Grades B and A represent higher levels ofperformance o
• The system will not detect a pressure loss without driving the vehiclefor at least 0.5 mile (0.8 km) at speeds greater than 25 mph (40 km/h).Reset w
• Transporting a heavy load or towing a trailer.• A different tire was replaced and was not the same brand, type, size,speed rating, load carrying cap
• Rim: The metal support (wheel) for a tire or a tire and tube assemblyupon which the tire beads are seated.INFORMATION CONTAINED ON THE TIRE SIDEWALL
Note: You may not find this information on all tires because it is notrequired by federal law.7. H: Indicates the tire’s speed rating. The speed ratin
10. Tire Ply Composition and Material Used: Indicates the number ofplies or the number of layers of rubber-coated fabric in the tire tread andsidewall
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation than those of “P” typetires; t
Information on “T” type tiresT145/80D16 is an example of a tiresize.Note: The temporary tire size foryour vehicle may be different thanthis example.1.
Bass: Press to adjust the bass setting. Use / / SEEK .Balance: Press to adjust the audio between the left and right speakers.Use/ / SEEK .Fade: Press
Use the recommended cold inflation pressure for optimum tireperformance and wear. Under-inflation or over-inflation may causeuneven treadwear patterns
6. Visually inspect the tires to make sure there are no nails or otherobjects embedded that could poke a hole in the tire and cause an airleak.7. Chec
• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)2004 Freestar (win)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specif
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive (4WD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can be corrected by rotati
When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to prevent your vehiclefrom skidding and hydroplaning.Built-in treadwear
Make sure all tires and wheels on the vehicle are of the same size, type,tread design, brand, load-carrying capacity and speed rating because itcan af
SNOW TIRES AND CHAINSDriving too fast for conditions creates the possibility of loss ofvehicle control. Driving at very high speeds for extended perio
MOTORCRAFT PART NUMBERSComponent 3.9L OHV V6 engine 4.2L OHV V6 engineAir filter element FA-1711 FA-1711Battery BXT-59 BXT-59BXT-65-750 BXT-65-750Fuel
REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluid1All Fill to MAX lineon res
3Use of synthetic or synthetic blend motor oil is not mandatory. Engineoil need only meet the requirements of Ford specificationWSS-M2C153–H and the A
8. Shuffle: Press to play CD tracksin random order.9. Compress (Compression): InCD mode, brings soft and loud CDpassages together for a more consisten
Item Ford partnameFord partnumberFordspecificationDoor latch, hoodlatch, auxiliaryhood latch, doorand liftgatehinges, strikerplates, seattracks, slidi
1Use only brake fluids certified to meet Ford specifications. DOT 3 fluidis recommended. However, if DOT 3 is not available, DOT 4 fluid can beused.2E
142004 Freestar (win)Owners Guide (post-2002-fmt)USA English (fus)Maintenance and Specifications282
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
1. World manufacturer identifier2. Brake type and gross vehicleweight rating (GVWR)3. Vehicle line, series, body type4. Engine type5. Check digit6. Mo
Truck application:Code Transmission DescriptionManual transmissionM Manual 5–speed (AKK))C Manual 5–speed overdrive (Close ratio)W Manual 5–speed over
Code Transmission/Transaxle DescriptionRear wheel drive automatic transmissionU4–speed overdrive (4R70W)A5–speed overdrive (5R55N)2004 Freestar (win)O
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford
LifestyleBike racksCargo organization and managementEngine block heaters and blanketsRear seat entertainment systems - DVDTowing mirrorsTrailer hitche
AAccessory delay ...66AdvanceTrac ...176Air bag supplemental restraintsystem ...145–146
19. CD eject: Press to eject a CD.20. CD slot: Insert a CD label sideup.21. Seek:Press to access theprevious strong station or track.22. Scan: Press f
plastic parts ...231washing ...229waxing ...229wheels ...
FFloor mats ...72Fluid capacities ...278Fuel ...248calc
LLampsautolamp system ...43bulb replacementspecifications chart ...49daytime running light ...44headlam
locking/unlocking doors ...91, 94Reverse sensing system ...182Roadside assistance ...193Roof rack ...
Transmissionbrake-shift interlock (BSI) ...179fluid, checking and adding(automatic) ...259lubricant specifications ...
295
296
Maintenance and Specifications 235Engine compartment 237Engine oil 238Battery 241Fuel information 248Low tire warning system 262Tire Information 264Pa
5. SEEK: Press / to access the next/previous strong radio station,cassette selection or CD track.When the rear seat controls are activated, rear seat
(DVD or CD) that is playing in the Family Entertainment System.Wireless headphones will not play audio from any other sources(AM, FM, tape, or Radio C
CD/CD PLAYER CAREDo:• Handle discs by their edges only. Never touch the playing surface.• Inspect discs before playing. Clean only with an approved CD
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele
Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up
DUAL ZONE MANUAL HEATING AND AIR CONDITIONING SYSTEMWITH REAR PASSENGER COMPARTMENT CLIMATE CONTROL(IF EQUIPPED)1. Air flow selections: Controlsthe di
5.RRear defrost:Press to activate/deactivate rear window defrost.Refer to Rear window defroster later in this chapter for more information.6. Recircul
• Set the fan to the highest speed initially, then adjust to maintainpassenger comfort.To aid in side window defogging/demisting in cold weather:1. Se
3. Passenger temperature control: Press to increase/decrease thetemperature for the passenger in the front of the vehicle.4.RRear defrost: Press to ac
automatically determine fan speed, airflow location, A/C on or off, andoutside or recirculated air, to heat or cool the vehicle to reach thedesired te
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
5. R Rear fan speed control: Press to enable the auxiliary systemor to adjust the rear fan speed from the front control. The rear fan speedsettings av
• Dual temperature control: Press and hold AUTO toengage/disengage separate passenger side temperature control.18. AUTO: Press to engage full automati
AUXILIARY CLIMATE CONTROL (IF EQUIPPED)1. Fan speed: Turn to select thedesired fan speed.2. Temperature/mode selection:The distribution of air from th
HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Note:
2. Deselect the auto lamps.3. Put the ignition in RUN.4. Put the ignition in OFF.5. Select the autolamps.• Note: Steps 2 through 5 must be performed w
Flash to passPull toward you slightly to activateand release to deactivate.Battery saverThe battery saver will shut off the exterior lamps and interio
Domelamp ControlThe panel dimmer control also controls the domelamp operation.• Rotate the thumbwheel fully to the right, past detent to activate thed
4. On the wall or screen you willobserve a light pattern with highintensity flat segments at the topedge of the pattern. If the flat edgesare not at t
Map lamps (if equipped)The map lamps and controls arelocated on the center overheadconsole. Press the raised portion oneach lens to activate the lamps
Dome lamps (if equipped)The front dome lamp is located overhead between the driver andpassenger seats.The dome lamp will stay on if thepanel dimmer co
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury and prevent possibledamage to others, you
Function Trade NumberFront park/turn lamps 3457AK (amber)Front sidemarker lamp 904NA (amber)Cornering lamps 3156KAuxiliary parking lamps 912Headlamps
3. Disconnect the electricalconnector from the bulb by pullingrearward and unlock the bulb byrotating it counterclockwise.Handle a halogen headlamp bu
4. To remove the parking/turnbulb, turn the socket on the bottomof the headlamp assemblycounterclockwise and pull the bulbstraight out of the socket.I
Replacing license plate lamp bulbThe license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
Changing the wiper blades1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas
ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamp. The visor willslide back and forth on the rod forincrease
Outside air temperatureThe temperature can be displayed ineither Centigrade or Fahrenheit.This is controlled via the MessageCenter. Please refer to th
3. Press and hold the momentarypush-button for approximately 4seconds, until VAR is displayed,then release it. (Pressing themomentary push-button for
SLIDING DOOR OPERATIONManual door operationIf equipped with a Power Sliding Door (PSD), turn the Power DoorLockout control on the overhead console to
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
Vehicle operation with the door in the open position is notrecommended. Abrupt vehicle acceleration or deceleration could causethe door to move sudden
• pushing and releasing the right orleft hand second row passengercontrol. The control(s) arelocated on the trim panel in frontof the sliding door.• m
Resetting the PSDThe power sliding door may operate incorrectly or not at all because ofthe following conditions:• a low voltage or dead battery• the
To open the sliding door when thechild safety lock is on:• Unlock the sliding door and openthe door from the outside.• Press the right or left handcon
CLOCK (IF EQUIPPED)Press the right + control to movethe time display forward.Press the left - control to move thetime display backwards.AUXILIARY POWE
• Located next to the second rowseat.• Located on the right trim panel inthe rear cargo area.POWER WINDOWSWhen closing the powerwindows, you should ve
One touch downAllows the driver’s window to openfully without holding the controldown. Press completely down onthe bottom part of the rocker switchand
Do not block the sensor on the backside of the inside rear view mirrorsince this may impair proper mirror performance.Will automatically adjust (darke
Fold-away mirrorsPull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.POWER ADJUSTABLE FOOT PEDALS (IF EQU
Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas
To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access e
Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET + controluntil you get to the desiredspeed,
• Depress the brake pedal. This willnot erase your vehicle’spreviously set speed.• Press the speed control OFFcontrol.Note: When you turn off the spee
CENTER CONSOLE (IF EQUIPPED)Your vehicle may be equipped with a variety of console features. Theseinclude:• Utility compartmentCELL PHONE USEThe use o
3. Use a screwdriver to screw locator post into vehicle carpeting. Exertpressure while turning to pierce the carpeting.When installed properly, the lo
1. Press and hold the two outsidebuttons releasing only when the redlight begins to flash after 20seconds. Do not repeat step one toprogram additional
8. Return to the vehicle and firmly press, hold for two seconds andrelease the HomeLink威 button. Repeat the press/hold/release sequenceagain, and, dep
may also be used at any time. In the event that there are stillprogramming difficulties, contact HomeLink威 at www.homelink.com or1–800–355–3515.Erasin
Selectable featuresResetPress this control to select and reset functions shown in the INFO menuand SETUP menu.Info menuThis control displays the follo
Average Fuel Economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in 100 km/liters ormiles/gallon.If you calculate
Setup menuPress this control for the followingdisplays:• Language• Units (English/Metric)• System CheckLanguage1. Select this function from theSETUP m
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
System checkSelecting this function from theSETUP menu causes the messagecenter to cycle through each of thesystems being monitored. For eachof the mo
• Warning returns upon another event.This acts as a reminder that these warning conditions still exist withinthe vehicle.Driver’s door ajar Warning ca
LIFTGATE AJAR. Displayed when the liftgate is not completely closed.TRANSMISSION OVERHEATED. Indicates the transmission isoverheating. This warning ma
CHECK FUEL CAP. Displayed when the fuel filler cap is not properlyinstalled. Check the fuel filler cap for proper installation. Refer to Fuelfiller ca
4. Press and hold the RESETcontrol to display “OIL LIFE SETTO 100%”. Your oil life is now reset.To reset the oil monitoring system to your personalize
• Charging system• Door sensor• Liftgate sensor• Exterior lamps• Traction control• Washer fluid• Brake FluidContact your dealer as soon as possible if
• liftgate trim-mounted switch (closing)Opening and Closing the PLG:The PLG controls will operate without having the key in the ignition. Thetransaxle
To power open or close the PLGwith the Key fob:1. Press this control twice withinthree seconds to power open thePLG. The interior lamps willilluminate
To operate the PLG manually:1. Disable the liftgate power function by placing the Power Door LockoutControl in the OFF position.2. Open and close the
CARGO AREA FEATURESCargo net (if equipped)The cargo pouch net secureslightweight objects in the cargoarea. Attach the net to the anchorsprovided. Do n
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
To adjust the cross-bar (if equipped) position:1. Loosen the thumbwheel at bothends of the cross-bar (bothcross-bars are adjustable).2. Slide cross-ba
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
remote entry keypad (if equipped), or using the lock button on theremote entry transmitter (if equipped).Childproof door locks• When these locks are s
• 3–button remote• 5–button remote• 6–button remoteThe remote entry system allows you to:• lock or unlock all vehicle doors and liftgate without a key
Unlocking the doors1. Press and release to unlock the driver’s door. Note: The interiorlamps will illuminate and the anti-theft system (if equipped) w
Opening power liftgate (PLG) (if equipped)Press the control twice within three seconds to power open the powerliftgate. The interior lamps will illumi
Sounding a panic alarmPressto activate the alarm. The alarm will cycle the horn, the turnsignals will flash, and the interior lamps will illuminate.Pr
Replacing lost remote entry transmittersIf you would like to have your remote entry transmitter reprogrammedbecause you lost one, or would like to buy
The illuminated entry system will turn off the interior lights if:• the ignition switch is turned to the 4 (ON) position, or• the keyless entry system
Deactivating/activating perimeter lampsYou may enable/disable this feature by having your vehicle serviced byyour authorized dealer.You may also perfo
Commentaires sur ces manuels