Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 15Entertainment Systems 19AM/FM stereo cassette with CD 19AM/FM stereo with CD
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa
Map lampsTo change the map lamp bulbs:1. Use a small screwdriver toremove the map lamp lens.2. To remove the old bulb, twist1⁄4turn and pull it out.3.
7. Once the bulb covers areremoved, the bulbs can be removedby turning them counterclockwiseand then pulling the bulbs straightout.Handle a halogen he
5. Rotate the bulb socketcounterclockwise and remove fromthe lamp assembly.6. Carefully pull the bulb out of thesocket and push in the new bulb.7. Ins
Replacing foglamp bulbsHandle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and donot tou
Replacing license plate lamp bulbThe license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate
Approach lamp bulb removal (if equipped)To change the bulbs:1. Make sure that all the doors areclosed and the interior lights haveautomatically turned
WINDSHIELD WIPER/WASHER CONTROLSRotate the windshield wiper controlto the desired interval, low or highspeed position.The bars of varying length are f
Checking the wiper bladesIf the wiper blades do not wipe properly, clean both the windshield andwiper blades using undiluted windshield wiper solution
TILT STEERINGPush the lever down to unlock thesteering column. While the lever isin the down position, tilt thesteering column to the desiredposition.
OVERHEAD CONSOLEThe appearance of your vehicle’s overhead console will vary according toyour option package.Forward storage bin and conversation mirro
Light is blinking:Engine misfire is occurring which could damage your catalytic converter.You should drive in a moderate fashion (avoid heavy accelera
To vent:• To tilt the moon roof into the vent position (when the glass panel isclosed), press and hold the top portion of the control. To close themoo
AUXILIARY POWER POINTPower points are designed for accessory plugs only. Do not hangany type of accessory or accessory bracket from the plug.Improper
Not equipped with rear climatecontrolPOWER WINDOWSPress and hold the rocker switches to open and close windows.• Press the top portion of therocker sw
One touch down• Press the bottom portion of therocker switch completely downand release quickly. The driver’swindow will open fully. Depressagain to s
Press the control to turn the mirrorOFF or AUTO.The mirror will automatically returnto the normal state whenever thevehicle is placed in R(Reverse)(wh
Reverse tilt down mirrors (if equipped)The side mirrors may beprogrammed to tilt down when thevehicle is put in R (Reverse). Referto the Message Cente
POWER ADJUSTABLE FOOT PEDALSThe accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park
To turn speed control off• Press OFF or• Turn off the vehicle ignition.Once speed control is switched off,the previously programmed setspeed will be e
To set a higher set speed• Press and hold SET +. Releasethe control when the desiredvehicle speed is reached or• Press and release SET + tooperate the
To disengage speed control• Depress the brake pedal.Disengaging the speed control willnot erase the previouslyprogrammed set speed.Pressing OFF will e
Safety beltIlluminates to remind you to fastenyour safety belts. For moreinformation, refer to the Seatingand safety restraints chapter.Air bag readin
Indicator lightThis light comes on when either theSET ACCEL or RES controls arepressed. The vehicle speed must beat or above 48 km/h (30 mph). Itturns
In any mode:• Press VOL + or − to adjustvolume.Climate control featuresPress TMP + or - to adjusttemperature.Press+ or - to adjust fan speed.HOMELINK姞
When programming your HomeLink威 Wireless Control System toa garage door or gate, be sure that people and objects are out ofthe way to prevent potentia
3. Simultaneously press and holdboth the HomeLink威 and hand-heldtransmitter button. Do not releasethe buttons until step 4 has beencompleted.Some entr
Gate Operator & Canadian ProgrammingDuring programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time for
Erasing HomeLink姞 buttonsTo erase the three programmedbuttons (individual buttons cannotbe erased):• Press and hold the two outerHomeLink威 buttons unt
CompassThe compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antennas.Magnetic or metall
Compass calibration adjustmentPerform this adjustment in an open area free from steel structures andhigh voltage lines. For optimum calibration, turn
Info menuThis control displays the followingcontrol displays:• Odometer/Compass• Trip odometer/Odometer/Compass• Distance to Empty• Average Fuel Econo
Compass zone/calibration adjustment1. Determine your magnetic zone byreferring to the zone map.2. Turn ignition to the ON position.3. Start the engine
Speed controlIlluminates when the speed controlis activated.Oil pressure/Engine coolantIlluminates when the engine coolanttemperature is above the nor
10. The compass is now calibrated.Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in liters/100 k
Distance to empty (DTE)Selecting this function from theINFO menu estimates approximatelyhow far you can drive with the fuelremaining in your tank unde
Easy exit seat (if equipped)This feature automatically moves the drivers seat backwards for easy exitfrom the vehicle.1. To disable/enable the easy ex
Language1. Select this function from theSETUP menu for the currentlanguage to be displayed.2. Pressing the RESET controlcycles the message center thro
The sequence of the system check report and how it appears in themessage center is as follows:1. FUEL LEVEL2. WASHER FLUID LEVEL3. ADVANCETRAC娂 (if eq
This acts as a reminder that these warning conditions still exist withinthe vehicle.Warning display StatusCheck backup aid (if equipped) Warning displ
DOOR AJAR. Displayed when a door is not completely closed.LIFTGATE OR LIFTGLASS AJAR. Displayed when the liftgate is notcompletely closed.CHECK ENGINE
CHECK CHARGING SYSTEM. Displayed when the electrical system isnot maintaining proper voltage. If you are operating electrical accessorieswhen the engi
DATA ERR. These messages indicate improper operation of the vehiclenetwork communication between electronic modules.• Fuel computer• Charging system•
CENTER CONSOLE (IF EQUIPPED)The center console offers several useful storage features. These include:1. Pen holder2. Tissue holder3. Cassette/CD organ
Four wheel drive low (if equipped)Illuminates when four-wheel drivelow is engaged. If the light continuesto flash have the system serviced.Four wheel
POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)Position the floor mat so that theeyelet is over the pointed end of theretention post and rotate forward tol
LUGGAGE RACKThe rear cross-bar can be adjusted to fit the item being carried. Thefront cross-bar does not move.To adjust the luggage rack, push theadj
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
REMOTE ENTRY SYSTEMThis device complies with part 15 of the FCC rules and with RS-210 ofIndustry Canada. Operation is subject to the following two con
Locking the doors/liftgatePress this control to lock all doorsand liftgate. The park/turn signallamps will flash once.To confirm all doors are closed
Memory feature (if equipped)The remote entry system can alsocontrol the memory feature.Press the control once to unlock thedriver’s door. Pressing the
Replacing the batteryThe remote transmitter is powered by one coin type three-volt lithiumbattery CR2032 or equivalent. Typical operating range will a
Programming remote transmittersIt is necessary to have all (maximum of four — original and/or new) ofyour remote transmitters available prior to begin
Smart unlocking featureThe smart unlocking feature prevents you from locking yourself out ofthe vehicle by unlocking the doors if the key is in the ig
KEYLESS ENTRY SYSTEMWith the keyless entry keypad, you can:• lock or unlock the vehicle doorswithout using the key.Your vehicle has a factory set 5 di
GAUGESEngine coolant temperature gaugeIndicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the nor
If you wish to erase your personal code, use the following instructions:1. Enter factory set code.2. Press 1/2 control and release.The system will now
Activating/deactivating autolockwith the keyless entry systemBefore following the activation ordeactivation procedures, make surethat the anti-theft s
Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 1(OFF) position.Automatic disarmingSwitching the ignition to the 3
Replacing coded keys can be very costly and you may want to store anextra programmed key away from the vehicle in a safe place to preventan unforeseen
5. Within 10 seconds of removing the second coded key, insert the newunprogrammed key (new key/valet key) into the ignition and turn theignition from
SEATINGAdjusting the front manual seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than
Pull the seatback handle up torecline the seat.Using the armrest (if equipped)Push the release control to movethe armrest up or down.Seating and Safet
Using the manual lumbar supportThe lumbar support control islocated on the outboard side of theseat.Turn the lumbar support controlforward for more su
Press the control to move the seatforward, backward, up or down.Memory seats/rearview mirrors/adjustable pedals (if equipped)This system allows automa
CLIMATE CONTROLLED SEATS (if equipped)The controls for the climate controlled seats are located on the centerconsole.To operate the climate controlled
Engine oil pressure gaugeIndicates engine oil pressure. Atnormal operating temperature, theneedle will be in the normal range(the area between the “L”
• There is a filter located underboth front seats.• It can be accessed from thesecond row seat. Move the frontseat all the way forward and upto ease a
To install climate controlled seat air filter:• First, position the filter in it’shousing making sure that the farforward end is all the way up inthe
For assistance, refer to the label located on the side of the seat cushion.Adjusting the 2nd row outboard seat for E-Z EntryThe 2nd row outboard seats
3. To return the seat to a seatingposition, push down on the seatuntil the seat is latched to the floor.4. Lift the seatback to the upright position.A
3. Locate the latch strap at the frontof the seat and pull to release theseat into a kneel down load floorposition. A moderate force may berequired to
The rear latch hooks mustbe properly engaged withthe floor striker. Position the rearlegs of the seat over the floorstrikers and engage.Folding the 20
3. To return the seat to the uprightposition, lift the seatback until thelatch is fully engaged.Adjusting the second row 20% seat (if equipped)Lift th
Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a collision.Th
Third row power folding seat (if equipped)The control buttons are located on the right-hand rear quarter trim panel(accessible from the liftgate area)
Third row adjustable head restraintsYour vehicle’s third row outboard seating positions are equipped withhead restraints which are vertically adjustab
If the key is left in the ON position during fueling, a minimum of 22.2 L(six gallons) must be added to the fuel tank in order for the gauge toinstant
SAFETY RESTRAINTSPersonal Safety SystemThe Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupant
Driver and passenger dual-stage air bag supplemental restraintsThe dual-stage air bags offer the capability to tailor the level of air baginflation en
Determining if the Personal Safety System is operationalThe Personal Safety System uses a warning light in the instrumentcluster or a back-up tone to
All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag (SRS) isprovided.It is extreme
Combination lap and shoulder belts1. Insert the belt tongue into the proper buckle (the buckle closest tothe direction the tongue is coming from) unti
The front outboard, rear outboard, and second and third row centersafety restraints in the vehicle are combination lap and shoulder belts.The front ce
2. Grasp the shoulder portion andpull downward until the entire beltis pulled out.3. Allow the belt to retract. As the belt retracts, you will hear a
When the Safety Canopy娂 system and/or the front airbags are activated,the safety belt pretensioners for the driver and right front passengerseating po
First row center lap belt (if equipped)Adjusting the lap beltThe lap belt should fit snugly and as low as possible around thehips, not across the wais
Conditions of operationIf... Then...The driver safety belt is notbuckled before the ignition switchis turned to the ON position...The safety belt warn
• Optional instrument clusterPress and release the TRIP/RESETbutton to toggle between theodometer and trip odometer display.Press and hold the button
The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to infla
1. Turn the ignition switch to the RUN (or ON) position. (DO NOTSTART THE ENGINE)2. Wait until the safety belt warning light turns off. (Approximately
Do not use extensions to change the fit of the shoulder beltacross the torso.Safety belt maintenanceInspect the safety belt systems periodically to ma
Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in
Do not attempt to service, repair, or modify the air bagsupplemental restraint systems or its fuses. See your Ford orLincoln Mercury dealer.The front
How does the air bag supplemental restraint system work?The air bag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suff
Several air bag system components get hot after inflation. Do nottouch them after inflation.If the air bag has deployed, the air bag will not function
Safety Canopy姟 system (if equipped)Do not place objects ormount equipment on ornear the headliner at the siderailthat may come into contact with adepl
How does the Safety Canopy姟 system work?The design and development of theSafety Canopy娂 system includedrecommended testing proceduresthat were develop
PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD1. EJ (Eject): Press to stop andeject a tape.2. EJ (Eject): Press to stop andeject a CD.3. BASS: Allows you to
The Safety Canopy娂 is mounted to roof side-rail sheet metal, behind theheadliner, above the first and second row seats. In certain lateralcollisions o
Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref
Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.Alwa
When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the
• Those with a high back.If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo
SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully fo
• The second row center seat can be moved forward to keep a child in achild restraint close to the front seat occupants. The seat should bemoved to th
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a
Installing child safety seats in the center front seating positionAlways transport children 12 years old and under in the rearseats and always properl
Locks and Security 142Keys 142Locks 142Anti-theft system 143Seating and Safety Restraints 155Seating 155Safety restraints 170Air bags 183Child restrai
4. BAL (Balance): Allows you toshift speaker sound between theright and left speakers. Press BALthen press SEL to shift sound to the leftor right .FAD
The tether strap anchors in your vehicle are in the following positions(shown from top view):• Second row bench seat• Second row bucket seatsAttach th
• center seating position (ifequipped)3. Route the child safety seat tether strap under the head restraint(outboard seats) and over the back of the se
6. Rotate the tether strap clip.7. Tighten the child safety seat tether strap according to themanufacturer’s instructions.Third row seating position1.
4. Clip the tether strap through theanchor loop as shown.If the tether strap is clippedincorrectly, the child safetyseat may not be retained properlyi
Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol:Never attach two LATCH child safe
Attach LATCH lower attachments of the child seat only to theanchors shown.If you install a child seat with rigid LATCH attachments, do not tightenthe
STARTINGPositions of the ignition1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval.2. ACCESSORY, allow
If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf
5. Turn the key to 3 (ON) withoutturning the key to 4 (START).Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to
Note: If the engine does not start within five seconds on the first try,turn the key to OFF, wait 10 seconds and try again. If the engine stillfails t
9. REW (Rewind): Worksintapeand CD modes.In tape mode, radio play continuesuntil rewind is stopped (with the TAPE control) or the beginning of thetape
“continuous squeal” sound is present while braking, the brake liningsmay be worn-out and should be inspected by a qualified servicetechnician.If you a
• We recommend that you familiarize yourself with this brakingtechnique. However, avoid taking any unnecessary risks.ABS warning lampABSTheABSwarning
Always set the parking brake fully and make sure that thegearshift is securely latched in P (Park).The parking brake is not recommended to stop a movi
Speed sensitive steeringYour vehicle is equipped with engine speed sensitive steering. At higherengine speeds associated with high vehicle speed, the
The air suspension shut-off switch islocated behind two access panels onthe left rear quarter trim panel, nearthe liftgate. To remove the firstpanel,
Press the bottom portion of theswitch to turn off the airsuspension.LIMITED-SLIP AXLE (IF EQUIPPED)This axle provides added traction on slippery surfa
Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.
AdvanceTrac娂 enhances your vehicle’s stability during maneuvers thatrequire all available tire traction, like in wet/snowy/icy road conditionsand/or w
indicator light in the instrument cluster remains on while the engine isrunning, have the system serviced immediately.Pressing the control once will d
AUTOMATIC TRANSMISSION OPERATIONBrake-shift interlockThis vehicle is equipped with a park/brake-shift interlock feature thatprevents the gearshift lev
The Federal Communications Commission (FCC) and the Canadian Radioand Telecommunications Commission (CRTC) recommend that FM radiobroadcasters use RDS
Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position andremove the key wheneve
Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position andremove the key wheneve
• additional engine downhill braking is desired. If towing a trailer, referto Driving while you tow in the Trailer towing section.To return to(Overdri
REVERSE SENSING SYSTEM (IF EQUIPPED)The RSS sounds a tone to warn the driver of obstacles near the rearbumper when R (Reverse) is selected. The RSS wi
The RSS detects obstacles up to 2meters (6 ft.) from the rear bumperwith a decreased coverage area atthe outer corners of the bumper,(refer to the fig
If equipped with the Control Trac 4x4 System, and 4L (4x4 LOW)is selected while the vehicle is moving, the system will notengage. This is normal and s
• 4H (4X4 HIGH) provides mechanically locked four-wheel drive powerto front and rear wheels. The “4X4” light will illuminate in theinstrument cluster
Using the Control Trac systemShifting from 2H to A4WD or 4HMove the control to the A4WD or4H position at any forward speed upto 88 km/h (55 mph). The
Shifting from 4L to 4H, A4WD or 2H1. Bring the vehicle to a stop andkeep the brake pedal depressed.2. Place the gearshift in N (Neutral).3. Move the c
Basic operating principles• Do not use 4H (4x4 HIGH) or 4L (4x4 LOW) on dry, hard surfacedroads. This may damage the drivelines and axles.• Drive slow
16. Power/volume: Press to turnthe system on/off. Turn toraise/lower the volume.If the volume is set above a certainlevel and the ignition is turned o
Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position andremove the key wheneve
Control Trac four–wheel drive systemWhen a four–wheel drive mode is selected, the Control Trac system usesall four wheels to power the vehicle. This i
If your vehicle is equipped with AdvanceTrac娂, press the AdvanceTrac娂button (refer to AdvanceTrac娂 Stability Enhancement System in thischapter) while
Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should
Driving on snow and iceFour–wheel drive vehicles have advantages over two–wheel drivevehicles in snow and ice but can skid like any other vehicle.Shou
These “aftermarket lift kits” could adversely affect the vehicle’s handlingcharacteristics, which could lead to loss of vehicle control or rollover an
Ford Motor Company recommends that caution be used with any vehicleequipped with a high load or device (such as ladder racks or pickup boxcover).Failu
• GAWR (Gross Axle Weight Rating): Carrying capacity for each axlesystem. The GAWR is specific to each vehicle and is listed on theSafety Certificatio
Always ensure that the weight of occupants, cargo and equipment beingcarried is within the weight limitations that have been established foryour vehic
TRAILER TOWINGTrailer towing puts additional loadson your vehicle’s engine,transmission, axle, brakes, tires, andsuspension. For your safety and tomax
PREMIUM IN-DASH SIX CD SOUND SYSTEMAUDIOPHILE IN-DASH SIX CD SOUND SYSTEM1. SEEK: Works in radio or CDmode. Press and releaseSEEK/ for previous/nextst
EngineRear axleratioMaximum GCWR -kg (lbs.)Trailer weightrange (0 -maximum) kg(lbs.)4x24.6L All 4762 (10500) 0-2268 (0-5000)5.4L All 6577 (14500) 0–40
• Weight distributing - requires an aftermarket weight distributingsystem which includes draw bar, hitch ball, spring bars and snap-upbrackets. The ve
4. Attach the trailer to the vehicle and adjust the hitch equalizers so thatthe front bumper height is within 0–13 mm (0.5 in) of the referencepoint.
• Consult your local motor vehicle speed regulations for towing a trailer.• To eliminate excessive shifting, use a lower gear. This will also assistin
Exceeding these limits may allow water to enter vehicle components:• causing internal damage to the components.• affecting driveability, emissions and
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call 1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany wil
FUEL PUMP SHUT-OFF SWITCHFUELRESETThis device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt
The fuel pump shut-off switch has ared reset button on top of it and islocated beneath the air suspensionswitch (if equipped). If the vehicleis not eq
FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth
2. REW (Rewind): In CD mode,press to reverse within the currenttrack.FF (Fast forward): In CD mode,press to advance within the currenttrack3. COMP or
Passenger compartment fuse panel / power distribution boxThe fuse panel is located under the right-hand side of the instrumentpanel.To remove the trim
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 10A* Run/Accessory - Front wipermotor, Ins
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description4 15A* DVD player, Rear seat audiocontrols, CDDJ (navigation radio)5 7.5A*
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description11 10A* A/C compressor clutch relay, A/Ccompressor clutch solenoid, Airsusp
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description18 10A* Auxiliary A/C temperature blenddoor actuator, Auxiliary A/C frontau
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description27 5A* Compass module, Reverse sensingsystem module, Brake shiftinterlock (
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description38 25A* Rear wiper motor, Washer pump(rear window wash)39 20A* Console powe
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description109 30A** Driver seat motor switch(non-memory), Memory module,Power memory
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel DescriptionR03 Hi-beam relay Fuse # 35, Hi-beam headlamps,Hi-beam indicatorR04 Rear wi
CHANGING THE TIRESIf you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel
5. EJ (Eject): To eject a singledisc, press EJ and thecorresponding preset buttonnumber. Press and hold to eject all loaded discs. The eject feature i
Removing the spare tire1. Fold the rear seat down. Refer toRear seats in the Seating andsafety restraints chapter.2. Remove the jack handle andwinch e
1. Park on a level surface, activatehazard flashers and set the parkingbrake.2. Place gearshift lever in P (Park),turn engine OFF and block thediagona
When one of the rear wheels is off the ground, the transmissionalone will not prevent the vehicle from moving or slipping off thejack, even if the tra
• Never use the front or rear differential as a jacking point.6. Remove the lug nuts with the lug wrench.7. Replace the flat tire with the spare tire,
5. Disassemble the tools and snap them back into the tool tray. Close theaccess hole with the rubber plug. Reinstall the tray into the vehicle andsecu
Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,
4. Make the final connection of the negative (-) cable to the jumpstarting stud located in the rear of the engine compartment, near thebattery. Do not
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
• FIND Program type: Allows you to search RDS-equipped stations fora certain category of music format: Classic, Country, Info, Jazz, Oldies,R&B, R
With a disabled vehicle (without access to wheel dollies, car haulingtrailer or flatbed transport vehicle) your vehicle can be towed (all wheelson the
GETTING THE SERVICES YOU NEEDAt homeFord Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai
Board membershipThe Board consists of:• Three consumer representatives• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa
Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a
If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest F
IN CALIFORNIA (U.S. ONLY)California Civil Code Section 1793.2(d) requires that, if a manufactureror its representative is unable to repair a motor veh
13. PUSH ON (Power/volume):Press to turn ON/OFF; turn toincrease or decrease volume levels.If the volume is set above a certainlevel and the ignition
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam
• Cover the highlighted areas to prevent water damage when cleaningthe engine.• 4.6L V8 engine• 5.4L V8 engine• Never wash or rinse the engine while i
PLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your dealer.• For routine clea
INTERIORFor fabric, carpets, cloth seats and safety belts:• Remove dust and loose dirt with a vacuum cleaner.• Remove light stains and soil with Motor
FORD, LINCOLN AND MERCURY CAR CARE PRODUCTSYour Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect i
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel.2. Go to the front of the vehicle a
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.6L V8 engines1. Battery2. Automatic transmission fluid dipstick3. Engine oil filler cap4. Power stee
17. DISC TUNE: In radio mode:Pressor to manually tunedown or up the radio frequencyband.In CD mode: Pressto select the previous disc or to select then
5.4L V8 engines1. Battery2. Automatic transmission fluid dipstick3. Engine oil filler cap4. Power steering fluid reservoir5. Engine oil dipstick6. Bra
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
3. Set the parking brake and ensure the gearshift is securely latched in P(Park).4. Open the hood. Protect yourself from engine heat.5. Locate and car
Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t
Ford production and aftermarket (Motorcraft) oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedtha
Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lightedsubstances to come near th
Because your vehicle’s engine is also electronically controlled by acomputer, some control conditions are maintained by power from thebattery. When th
ENGINE COOLANTChecking engine coolantThe concentration and level of engine coolant should be checked at themileage intervals listed in the scheduled m
• Refer to the Scheduled Maintenance Guide for service intervalschedules.• Be sure to read and understand Precautions when servicing yourvehicle in th
• A large amount of water without engine coolant may be added, in caseof emergency, to reach a vehicle service location. In this instance, thecooling
Cleaning 281Maintenance and Specifications 287Engine compartment 289Engine oil 291Battery 294Fuel information 303Air filter(s) 315Low tire warning sys
When the rear seat controls are activated, rear seat passengers can usethe controls to change the playing media for all passengers (Single Playmode).
After any coolant has been added, check the coolant concentration, referto Checking Engine Coolant section. If the concentration is not 50/50(protecti
If you drive in extremely hot climates:• It is still necessary to maintain the coolant concentrationabove 40%.• NEVER decrease the coolant concentrati
When this occurs the vehicle will still operate. However:• The engine power will be limited.• The air conditioning system will be disabled.Continued o
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsDo not overfill the fuel tank. The pressure in an overfilled tankmay cause leak
• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek med
Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1/8 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref
Repairs to correct the effects of using a fuel for which your vehicle wasnot designed may not be covered by your warranty.Octane recommendationsYour v
• Your “Service Engine Soon” indicator may come on. For moreinformation on the “Service Engine Soon” indicator, refer to theInstrument cluster chapter
• Use the same filling rate setting (low — medium — high) each timethe tank is filled.• Allow no more than 2 automatic click-offs when filling.• Alway
• Idling for long periods of time (greater than one minute) may wastefuel.• Anticipate stopping; slowing down may eliminate the need to stop.• Sudden
To adjust the volumeThe volume control allows the rear seat passengers to adjust the volumelevel of the audio system.Press the + control to increasevo
• Using fuel blended with alcohol may lower fuel economy.• Fuel economy may decrease with lower temperatures during the first12–16 km (8–10 miles) of
If other than Ford, Motorcraft or Ford-authorized parts are used formaintenance replacements or for service of components affectingemission control, s
Allow the vehicle to sit for at least eight hours without starting theengine. Then, start the engine and complete the above driving cycle. Theengine m
BRAKE FLUID RESERVOIRThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the
Low fluid levelDo not drive the vehicle if the fluidlevel is at the bottom of the dipstickand the ambient temperature isabove 10°C (50°F).Correct flui
If an overfill occurs, excess fluidshould be removed by a qualifiedtechnician.An overfill condition oftransmission fluid may cause shift and/or engage
2. Loosen the clamp that securesthe air filter cover to the air filterhousing and carefully separate thecover from housing.3. Remove the air filter el
Tire Quality Grades apply to new pneumatic tires for use on passengercars. They do not apply to deep tread, winter-type snow tires,space-saver or temp
The temperature grade for this tire is established for a tire thatis properly inflated and not overloaded. Excessive speed,underinflation, or excessiv
• Four tire rotationReplacing the tiresReplace the tires when the wearband is visible through the tiretreads. Due to exposure to theelements and exhau
Mode selectPush the MODE control to togglebetween AM, FM1, FM2, tape (ifequipped), CD, CD changer (ifequipped) or DVD (if equipped). Ifin Dual Play mo
Failure to follow these precautions may adversely affect thehandling of the vehicle, and increase the risk of loss of vehiclecontrol, vehicle rollover
Changing tires with TPMSIt is recommended that you alwayshave your tires serviced by a dealeror qualified technician. Each tire isequipped with a tire
• Do not exceed 48 km/h (30 mph) with tire chains on your vehicle.MOTORCRAFT PART NUMBERSComponent 4.6L V8 engine 5.4L V8 engineAir filter element FA-
Fluid Ford PartNameApplication CapacityEngine coolant3MotorcraftPremium GoldEngine Coolant(yellow-colored)4.6L V8 enginewith 1 rowradiator19.0L (20.1q
Fluid Ford PartNameApplication CapacityWindshieldwasher fluidMotorcraftPremiumWindshieldWasherConcentrateAll 4.1L (4.5quarts)1Ensure the correct autom
LUBRICANT SPECIFICATIONSItemFord partnameFord partnumberFordspecificationHinges, latches,striker platesand rotors, seattracks, fuel fillerdoor hinge a
ItemFord partnameFord partnumberFordspecification4x4 front wheelbearings, 4x4spindle needlebearings, spindlethrust bearings& front driveaxle u-joi
ItemFord partnameFord partnumberFordspecificationWindshieldwasher fluidMotorcraftPremiumWindshieldWasherConcentrateZC-32–A WSB-M8B16–A21Ensure the cor
VEHICLE DIMENSIONSVehicle dimensions 4x2 mm (in) 4x4 mm (in)(1) Overall length 5228(205.8)5228(205.8)(2) Vehicle width(Body)2000(78.7)2000(78.7)(2) Ve
14Maintenance and Specifications329
Parental controlPress the memory preset controls 3and 5 simultaneously on the frontaudio controls to disable the rearseat controls. They will remain d
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincol
Comfort and convenienceBattery warmerCargo organizersCargo traysCarpeted cargo matDash trim (wood grain)Door edge guardsMolded in color running boards
Removable luggage rack adaptersRoof rack cross barsSki/snowboard carrierSoft luggage coverTrailer hitch bars and ballsTrailer hitch receiver coverProt
• The Federal Communications Commission (FCC) and Canadian RadioTelecommunications Commission (CRTC) regulate the use of mobilecommunications systems
AABS (see Brakes) ...210Accessory delay ...113Air bag supplementalrestraint system ...183–184, 188and chil
Child safety seats ...195in front seat ...196in rear seat ...196, 199Cleaning your vehi
Engine ...327–328check engine/service enginesoon light ...10cleaning ...
GAWR (Gross Axle WeightRating) ...236calculating ...238definition ...
Lights, warning and indicator ...10AdvanceTrac ...12air bag ...12anti-lock brakes (ABS
Don’t:• Expose tapes to direct sunlight, extreme humidity, heat or cold.• Leave tapes in the cassette player for a long time when not beingplayed.CD/C
Power Windows ...112Preparing to drive yourvehicle ...215RRadio ...
checking the pressure ...318replacing ...319rotating ...318snow tires and cha
343
344
DVD player controls1. MAIN control• NEXT — Press to access the next track on the CD, the next chapteron the DVD, or to go up in cursor mode.• PREV — P
7. Auxiliary jacksInsert lines for standard video game players.8. STOP/EJECT controlPress once to stop DVD play. Press again to eject the DVD.9. DISPL
• Press the FWD control to movethe cursor right one positionNext/Previous controlThe NEXT (up) and PREV (down)controls allow you to access thenext or
Slow play modeTo enter slow play mode, press thePLAY/PAUSE control. Once thesystem is in pause mode, press theFWD or REV control for slow motion playb
Remote control1. REWIND controlPress to reverse the direction of the DVD movie.2. FAST FORWARD controlPress to advance the direction of the DVD movie.
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
In stop mode, press to change to a different playing media (e.g. AM, FM,CD...)8. VOLUME controlPress to increase (+) or decrease (-) volume level.Batt
To install the batteries, lightly pressdown on the top of the left earpieceand slide the cover off.When replacing the batteries, usetwo new batteries
Liquid Crystal Display (LCD) flip-down screenThe screen rotates down to view and into the housing to store when notin use. Be sure the screen is latch
Rear Seat Entertainment DVD System protection circuitsHigh temperature sensor circuit• Excessively high temperatures may cause damage to the DVD playe
Inserting a CD/DVDInserting a CD/DVD into the DVD player automatically turns the powerON and playback should begin.The counter is automatically reset
On-screen indicatorsEach time a control is pressed, the operational status of the DVD playeris shown on the screen. The following are some possible in
Do not expose the liquid crystal display (LCD) flip-down screento direct sunlight or intensive ultraviolet rays for extensiveperiods of time. Ultravio
Care and service of the DVD playerEnvironmental extremesDVD players that are subjected to harsh environmental conditions maybe damaged or perform at l
Cleaning compact discsInspect all discs for contamination before playing. If necessary, cleandiscs only with an approved CD cleaner and wipe from the
A safety screen will be displayedeach time the navigation system isturned on as a reminder. Ensurethat you are familiar with thesystem’s features and
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury and prevent possibledamage to others, you
System overview1. HOME: When the home locationis empty, pressing and holding thiskey will store the vehicle’s currentlocation as home. Pressing the ho
4. Cursor control: Use this controlwhen viewing a menu in thenavigation system. Press the controlup or down, left or right to highlightan item in the
11. On/volume: Press the ONcontrol to turn on the VNR system.Press again to turn the system off.Turn the control to adjust the audiovolume levels. To
2. Press the AM/FM control to selectthe desired frequency band.3. Press the SEEK control to locatea station.To play a CD in the VNR:1. Ensure that the
2. Press the NAV control to enterinto Navigation mode.3. To enter a destination, ensurethat the vehicle is in the PARK position.4. To navigate to home
Turn the control to raise or lowervolume. The levels will be displayedon the screen.To adjust the navigation voiceoutput level, adjust the volumecontr
AM/FM selectThe AM/FM control works in radio,CD and navigation modes.AM/FM select in radio modeThis control allows you to select AM or FM frequency ba
If a navigation CD is in the head unit and you press CD, the system willautomatically search for an audio CD in the CD DJ and begin play if it isprese
Press the soft key to turn the feature on or off.This feature can be accessed by selecting the menu option “More, AVC,Traffic, DSP..” within the “Audi
Seek in CD or CD DJ mode• Pressto seek to the previous track of the current disc. If aselection has been playing for three seconds or more and youpres
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and
Starting autoset memory preset1. Select a frequency band using the AM/FM select controls.2. Press the AUTO control.3. When the first six strong statio
Scan functionPress the soft key next to SCAN fora brief sampling of all listenablestations on the selected frequency.Press again to disable scan andre
CompressionThe compression feature will boostquieter music and lower loudermusic to minimize the need forvolume adjustments.When in CD or CD DJ mode,
(STOP) / AUX — If a DVD movie is playing, press to stop. If a movieis not playing, press to activate AUX mode.CD DJYour vehicle is equipped with a CD
Press to eject the magazine.1. Pull the lever to remove a CDtray from the magazine.2. Insert one disc into each CD trayof the magazine (up to 6 discs)
4. Insert the CD magazine into theCD DJ.5. Slide the door to the left to close.Use only compact discs containingthis mark.The magazine does not need t
CD DJ information screenThe CD DJ screen will displayvarious information such as:• Track selected• Elapsed time• Selected disc• Volume level• On-scree
Scan featureWhen in CD DJ mode, press SCANfor a brief sampling of all tracks onthe current CD. Press again todisengage the feature and listen tothe se
When RSC is active, pressing presets 2 and 4 simultaneously on the radiowill enable Dual Play mode (or the RSC can enable Dual Play mode bypressing th
6. ZOOM7. PAN8. DETOUR9. VOICEPlease drive safelyThis screen may appear on yourVNR display. Press the soft key nextto the display to select the desire
Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental Restraint
The GPS signal strength may vary. The directional heading indicator atthe bottom of the screen might change color to indicate this signalstrength. The
Selecting a destinationPress NAV to access the destinationentry menu.From this menu, you may selectfrom the following options:• Address/Intersection –
Points of Interest (POI)This destination option enables youto specify a particular place, such asan airport or gas station. Use thesoft keys to select
Previous destinationThe last 50 destinations entered intothe navigation system areautomatically stored in the system’smemory.Use the soft key to selec
• Use the cursor control to scroll through the selections.• Press in the cursor control to confirm the selection.Selecting Route CriteriaOnce you have
Please proceedOnce the route is calculated, ’PleaseProceed’ is displayed with a map onthe display. Also included in thedisplay:•the planned route is s
• CANCEL — Press to cancel the guide display.While in the Guide display screen, the cursor input can be used topreview future/up coming maneuvers. Thi
Adding, deleting or editing the address bookNote: These features are not available when the vehicle is in motion.1. Ensure that you are in navigationm
Current locationTo access your current location,press HERE when in navigationmode. Your current location and thename/distance to the next/lastintersec
Route interruptionsIn the course of your destination, you may decide to temporarily leaveyour planned route for gas, food, etc. If you turn off the ig
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
Navigation optionsOnce in the navigation preferencemenu, you may select from thefollowing options:• VOICE — Select to turn the voiceoutput on or off a
• Clock Setting: Your vehicle is equipped with your clock in the VNRsystem. To set the clock:1. Access the CLOCK screen.2. Press the ADJUST control to
Cleaning the displayDo not spray cleaning fluid directly onto the unit. Instead, spray onto asoft cloth and gently wipe the unit. Only recommended pro
MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED)1. Temperature control2. Mode selector control3. A/C control4. Rear defrost control5. Fan spee
MODE SELECTOR CONTROLControls the direction of the airflowto the inside of the vehicle.The A/C compressor will onlyfunction if the outside temperature
A/C controlA/CUsed to manually enable or disable the operation of the air conditioningin all modes except Floor & Defrost, Defrost and Max A/C.Whe
DUAL ELECTRONIC AUTOMATIC TEMPERATURE CONTROL(DEATC) SYSTEM (IF EQUIPPED)1. A/C control2. Recirculated air control3. Passenger temperature control4. R
AUTOMATIC OPERATIONPress AUTO and select the desiredtemperature. The system will eitherheat or cool the vehicle to achievethe selected temperature. Th
TEMPERATURE CONVERSIONPress the F/C control to switchbetween Fahrenheit and Celsiustemperature on the display. Thetemperature in Celsius will bedispla
In automatic operation, the air conditioning operates as necessary toachieve the selected temperature and the A/C indicator will be lit. Ifdesired, th
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
MANUAL OVERRIDE CONTROLSThe manual override controls allow you to determine where airflow isdirected. To return to full automatic control, press AUTO.
OPERATING TIPS• To reduce fogging in humid weather conditions, unless in Defrost orFloor & Defrost, press the A/C control before driving as the ai
The auxiliary climate control system is dependent on the main climatecontrol system. If the main climate control system is in the Off position,the aux
REAR WINDOW DEFROSTERUsed to manually enable or disablerear window defrost in all modes.After approximately 10 minutes ofrear defrost operation, the c
HEADLAMP CONTROLRotate the headlamp control to thefirst positionto turn on theparking lamps. Rotate to the secondpositionto turn on theheadlamps.Fogla
Daytime running lamps (DRL) (if equipped)Turns the foglamps on at full intensity output. To activate:• the ignition must be in the ON position and• th
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parklamp operatio
5. Locate the vertical adjuster oneach headlamp, then use a 10 mmsocket/wrench to turn the adjustereither counterclockwise (to adjustdown) or clockwis
Front row dome lamp/ map light (if equipped)The dome lamp lights when:• any door is opened,• the instrument panel dimmerswitch is rotated up until the
BULBSReplacing exterior bulbsCheck the operation of all the bulbs frequently.Using the right bulbsReplacement bulbs are specified in the chart below.
Commentaires sur ces manuels