Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 15Entertainment Systems 18AM/FM stereo 18AM/FM stereo cassette 22AM/FM stereo w
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa
REAR SEATS2nd seat/split-folding rear seat (if equipped)One or both rear seatbacks can be folded down to provide additionalcargo space.To lower the se
3. Lift the remote latch release onthe left side of the compartmentand fold the remaining floor paneluntil it latches. Make sure theseatback is locked
How does the personal safety system work?The Personal Safety System can adapt the deployment strategy of yourvehicle’s safety devices according to cra
safety belt pretensioner activation depending upon safety belt usage.Refer to Safety Belt section in this chapter.Front safety belt pretensionersThe s
Safety belt precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injury, mak
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
response to vehicle movement. For example, if the driver brakessuddenly or turns a corner sharply, or the vehicle receives an impact ofapproximately 8
• Grasp the shoulder portion andpull downward until the entirebelt is extracted.• Allow the belt to retract. As the belt retracts, you will hear a cli
Safety belt pretensionerYour vehicle is equipped with safety belt pretensioners at the driver andfront outboard passenger seating positions.The safety
Front safety belt height adjustmentYour vehicle has safety belt heightadjustments for the driver and frontpassenger. Adjust the height of theshoulder
If the light remains on, have your vehicle serviced at the firstavailable opportunity.Note: Thelight will illuminate if vehicle refueling is conducted
Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ
grasp the tongue so that it is parallel to the webbing and slide thetongue upward. Provide enough length so that the tongue can reach thebuckle.To fas
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war
The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra
Do not sit on top of a buckled safety belt to avoid the BeltMinder chime. Sitting on the safety belt will increase the risk ofinjury in an accident. T
4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps.5. Buckle then unbuckle the safety belt three times, ending with thesafety belt u
attaching hardware, should be inspected after a collision. Ford MotorCompany recommends that all safety belt assemblies used in vehiclesinvolved in a
HOW DO THE AIR BAG SUPPLEMENTAL RESTRAINTS WORK?The air bag supplemental restraint system consists of:• driver and passenger dual stage air bag module
National Highway Traffic Safety Administration (NHTSA)recommends a minimum distance of at least 25 cm (10 inches)between an occupant’s chest and the d
Children and air bagsFor additional important safetyinformation, read all information onsafety restraints in this guide.Children must always be proper
light will momentarily illuminate prior to reaching the START position).It also illuminates if the parking brake is engaged. If the brake systemwarnin
force, there is the risk of death or serious injuries such as fractures,facial and eye injuries or internal injuries, particularly to occupants whoare
Do not use accessory seat covers. The use of accessory seatcovers may prevent the deployment of the side air bags andincrease the risk of injury in an
How does the side air bag system work?The side air bag system consists ofthe following:• An inflatable nylon bag (air bag)with a gas generator conceal
Several air bag systemcomponents get hot afterinflation. Do not touch them afterinflation.If the side air bag has deployed, the air bag will not funct
When possible, always place children under age 12 in the rearseat of your vehicle. Accident statistics suggest that children are saferwhen properly re
Booster seats should be used until you can answer YES to ALL of thesequestions:• Can the child sit all the way backagainst the vehicle seat back withk
The shoulder belt should cross the chest, resting snugly on the center ofthe shoulder. The lap belt should rest low and snug across the hips,never up
safety seat you put in your vehicle. If you do not install and use thesafety seat properly, the child may be injured in a sudden stop orcollision.When
Installing child safety seats in combination lap and shoulder beltseating positionsAir bags can kill or injure a child in a child seat. NEVER place ar
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
Engine oil pressureIlluminates when the oil pressurefalls below the normal range. Checkthe oil level and add oil if needed.Refer to Engine oil in theM
7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat.
6. Before placing the child into the child seat, forcibly tilt the child seatfrom side to side and in forward direction to make sure that the seat iss
3. Locate the correct anchor for theselected seating position.4. Open the tether anchor cover.5. Clip the tether strap to theanchor as shown.If the te
Attaching safety seats with LATCH (Lower Anchors and Tethers forChildren) attachments for child seat anchorsSome child safety seats have two rigid or
Follow the child seat manufacturer’s instructions to properly install achild seat with LATCH attachments. Two plastic LATCH guides can beobtained at n
STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
4. Make sure the parking brake isset.5. Turn the key to 4 (ON) withoutturning the key to 5 (START).Make sure the corresponding lights illuminate or il
1. Turn the key to 5 (START)without pressing the acceleratorpedal and release as soon as theengine starts. The key will return to4 (ON).2. If the temp
tank will improve cold starting performance. Your vehicle is designed tooperate on (Ed85) ethanol alone, unleaded gasoline alone, or any mixtureof the
Turn signalsIlluminates when the turn signals orthe hazard lights are turned on. Ifthe lights stay on continuously orflash faster, check for a burned-
Have the exhaust and body ventilation systems checked whenever:• the vehicle is raised for service.• the sound of the exhaust system changes.• the veh
Anti-lock brake system (ABS) (if equipped)On vehicles equipped with an anti-lock braking system (ABS), a noisefrom the hydraulic pump motor and pulsat
With the ABS light on, the anti-lockbrake system is disabled and normalbraking is still effective unless thebrake warning light also remainsilluminate
Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.Park brak
During Traction Control娂 operation,the traction control active light willilluminate, you may hear an electricmotor type of sound coming fromthe engine
AUTOMATIC TRANSMISSION OPERATIONBrake-shift interlockThis vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever fr
Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position andremove the key wheneve
Hold the brake pedal down while you move the gearshift leverfrom P (Park) to another position. If you do not hold the brakepedal down, your vehicle ma
N (Neutral)With the gearshift lever in the N(Neutral) position, the vehicle canbe started and is free to roll. Holdthe brake pedal down while in thisp
When to use D (Drive)The D (Drive) position eliminatesthe needless shifting back and forthbetween third and fourth gears thatyour vehicle may do when
Park brake warning chimeSounds when the parking brake is set, the engine is running and thetransaxle is not in P (Park) or N (Neutral). The chime will
When parking, do not use the gearshift in place of the parkingbrake. Always set the parking brake fully and make sure that thegearshift is securely la
• GAWR (Gross Axle Weight Rating): Carrying capacity for each axlesystem. The GAWR is specific to each vehicle and is listed on theSafety Certificatio
your vehicle including both gross vehicle weight and front and rear grossaxle weight rating limits. Under no circumstance should these limitationsbe e
3.0L 4-Valve Duratec EngineModel Passenger Load- #/kg (lbs.)Luggage Load -kg (lbs.)Max TrailerWt.- kg (lbs.)Sedan 5/340 (750) 0 590 (1300)2/135 (300)
Trailer brakesElectric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspeci
• The trailer tongue weight should be 10–15% of the loaded trailerweight.• After you have traveled 80 km (50 miles), thoroughly check yourhitch, elect
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford Motor Companyoffers a complimentary roadside assistance program
If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S
If your vehicle is a sedan, the fuelpump shut-off switch is located onthe right side of the trunk behindthe trunk liner.If your vehicle is a wagon, th
FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth
Fuel gaugeDisplays approximately how muchfuel is in the fuel tank. The fuelgauge may vary slightly when thevehicle is in motion or on a grade.When ref
Passenger compartment fuse panelThe fuse panel is located below and to the left of the steering wheel bythe brake pedal. Remove the panel cover to acc
Fuse/relaylocationFuse ampratingPassenger compartment fusepanel description13 20A Power point14 — Not used15 30A Front wiper motor16 15A Flasher and G
Fuse/relaylocationFuse ampratingPassenger compartment fusepanel description34 — Not used35 — Not used36 15A Turn signals, Back-up lamps37 15A Transmis
If the battery has been disconnected and reconnected, refer to theBattery section of the Maintenance and specifications chapter.The high-current fuses
Fuse/relaylocationFuse ampratingPower distribution boxdescription17 20A* Cell port18 20A* Cigar lighter19 15A* Right headlamp20 — Not used21 15 A* Lef
Temporary spare tire informationThe temporary spare tire for your vehicle is labeled as such. It is smallerthan a regular tire and is designed for eme
To prevent the vehicle from moving when you change a tire, besure the parking brake is set, then block (in both directions) thewheel that is diagonall
3. If equipped with a wheel coverthat’s bolted on, loosen the fiveplastic nuts with the lug nutwrench.4. Remove the center ornament or wheel cover fro
10. Remove the jack and fullytighten the lug nuts in the ordershown.11. Return the flat tire, jack and lugwrench to their proper storagelocations. Mak
Preparing your vehicleWhen the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, th
Trip odometerRegisters the kilometers (miles) ofindividual journeys. To reset,depress the control.TachometerIndicates the engine speed inrevolutions p
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
4. Make the final connection of the negative (-) cable. Make theconnection to an exposed metal part of the stalled vehicle’s engine, awayfrom the batt
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center.It
GETTING THE SERVICES YOU NEEDAt homeFord Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai
Board membershipThe Board consists of:• Three consumer representatives• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa
AM/FM STEREOVolume/power controlPress the control to turn the audiosystem on or off.Turn control to raise or lowervolume.If the volume is set above a
Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral
mediation/arbitration program administered by the Canadian MotorVehicle Arbitration Plan (CAMVAP).The CAMVAP program is a straight-forward and relativ
If you are in another foreign country, contact the nearest Forddealership. If the dealership employees cannot help you, they can directyou to the near
California Civil Code Section 1793.22(b) presumes that the manufacturerhas had a reasonable number of attempts to conform the vehicle to itsapplicable
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is
• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips.• Always
• 3.0L Vulcan engine• 3.0L Duratec engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PL
WINDOWS AND WIPER BLADESThe windshield, rear window and wiper blades should be cleanedregularly. If the wiper does not wipe properly, substances on th
INTERIORFor fabric, carpets, cloth seats, safety belts and seats equipped with sideair bags:• Remove dust and loose dirt with a vacuum cleaner.• Remov
FORD, LINCOLN AND MERCURY CAR CARE PRODUCTSYour Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect i
Bass/treble adjust• The bass adjust control allowsyou to increase or decrease theaudio system’s bass output.• The treble adjust control allowsyou to i
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
Working with the engine on1. Set the parking brake and ensure the gearshift is securely latched in P(Park).2. Block the wheels to prevent the vehicle
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.0L V6 Vulcan engine1. Automatic transmission fluid dipstick2. Brake fluid reservoir3. Air filter ass
3.0L DOHC V6 Duratec engine1. Automatic transmission fluid dipstick2. Brake fluid reservoir3. Air filter assembly4. Battery5. Engine oil dipstick6. En
WINDSHIELD WASHER FLUIDCheck the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with asymbol.Add fluid to fill the reservoir if t
Checking and adding washer fluid for the liftgate (if equipped)The opening for the reservoir islocated on the passenger side underthe tail lamp. Refil
5. Locate and carefully remove theengine oil indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.• If th
Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t
that does not meet Ford material and design specifications, start-upengine noises or knock may be experienced.It is recommended you use the appropriat
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a
Locks and Security 83Keys 83Locks 83Anti-theft system 84Seating and Safety Restraints 97Seating 97Safety restraints 101Air bags 116Child restraints 12
AM/FM selectThe AM/FM select control works inradio mode. Press the AM or FMcontrol to enter radio mode.AM/FM select in radio modeThis control allows y
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “cold fill level” or within the “c
Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant couldmake it difficult to see through
For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when
Recycled engine coolantFord Motor Company recommends the use of a recycled engine coolantproduced by Ford-approved processes in vehicles originally eq
• Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may cause engine da
Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforefueling your vehicle.• Alwa
small amount of a bad tasting chemical is added to discourage beverageuse. The resulting fuel is called Ed100 meaning 100% pure ethanoldiluted by 2% t
Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1/8 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref
Your vehicle was not designed to use fuel or fuel additives with metalliccompounds, including manganese-based compounds containing MMT.Repairs to corr
To set the minute, press and holdthe minute (M) control. When thedesired minute appears, release thecontrol.Your vehicle is equipped with a special fe
It should not be necessary to add any aftermarket products to your fueltank if you continue to use high quality fuel of the recommended octanerating.
Fuel FilterFor fuel filter replacement, see your dealer or a qualified servicetechnician. Refer to the scheduled maintenance guide for the appropriate
• Always use fuel with the recommended octane rating.• Use a known quality gasoline, preferably a national brand.• Use the same side of the same pump
• Anticipate stopping; slowing down may eliminate the need to stop.• Sudden or hard accelerations may reduce fuel economy.• Slow down gradually.• Driv
• Driving on flat terrain offers improved fuel economy as compared todriving on hilly terrain.• Transmissions give their best fuel economy when operat
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
engine must warm up to its normal operating temperature. Once started,do not turn off the engine until the above driving cycle is complete.CHECKING AN
Note: The 3.0L V6 Vulcan enginemay have a different type powersteering fluid reservoir that uses adipstick to check fluid level. Withthis application,
Brake fluid is toxic. If brake fluid contacts the eyes, flush eyeswith running water for 15 minutes. Seek medical attention ifirritation persists. If
7. Remove the dipstick and inspect the fluid level. The fluid should be inthe designated areas for normal operating temperature.Low fluid levelDo not
MACH姞 AUDIO SYSTEM WITH AM/FM STEREO/CASSETTEVolume/power controlPress the control to turn the audiosystem on or off.Turn control to raise or lowervol
Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may affect transmissionoperation and re
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
• Four tire rotationReplacing the tiresReplace the tires when the wearband is visible through the tiretreads.When replacing full size tires, never mix
Tires that are larger or smaller than your vehicle’s original tires may alsoaffect the accuracy of your speedometer.SNOW TIRES AND CHAINSSnow tires mu
MOTORCRAFT PART NUMBERSComponent 3.0L V6 Vulcanengine3.0L FFV V6engine3.0L DOHC V6Duratec engineAir filterelement1FA-1683 FA-1683 FA-1683Fuel filter F
REFILL CAPACITIESFluid Ford Part Name Application CapacityBrake fluid Motorcraft HighPerformance DOT3 Motor VehicleBrake FluidAll Fill to line onreser
LUBRICANT SPECIFICATIONSItemsFord PartName orequivalentFord PartNumberFordSpecificationBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeF
ItemsFord PartName orequivalentFord PartNumberFordSpecificationPower steeringfluidMotorcraftMERCON威 ATFXT-2-QDX MERCON威Windshieldwasher fluidMotorcrar
ENGINE DATAEngine 3.0L V6 Vulcanengine3.0L FFV V6engine3.0L DOHC V6Duratec engineCubic inches 182 182 183Required fuel 87 octane 87 octane orEthanol (
52341Maintenance and Specifications229
Bass/treble adjust• The bass adjust control allowsyou to increase or decrease theaudio system’s bass output.• The treble adjust control allowsyou to i
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea
FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincol
Travel equipmentElectrochromic inside mirror with compassElectrochromic inside mirror with compass and temperatureEmergency kitFactory luggage rack ad
For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle:• When adding accessories,
AABS (see Brakes) ...141Accessory delay ...70Air bag supplemental restraintsystem ...116
Child safety seats ...126attaching with tether straps...131in front seat ...128in rear seat ...
starting after a collision ...157Engine block heater ...139Engine oil ...195checking and adding ...
IIgnition ...135, 228Infant seats(see Safety seats) ...126Inspection/maintenance (I/M)testing ...
MMirrors ...68automatic dimming rearviewmirror ...70heated ...
Scan functionThe scan function works in radio,tape or CD mode.Scan function in radio modePress the SCAN control to hear a brief sampling of all listen
Spare tire (see Changing theTire) ...165Spark plugs, specifications ...224,228Specification chart,lubricant
Radio station memory presetThe radio is equipped with six station memory preset controls. Thesecontrols can be used to select up to six preset AM stat
Tune adjust in radio mode• Pressto move to the next frequency down the band (whether ornot a listenable station is located there). Hold the control to
RewindThe rewind control works in tapeand CD modes.• In tape mode, radio play willcontinue until rewind is stopped(with the TAPE or REW control) or th
Compression adjustCompression adjust brings soft andloud CD passages together for amore consistent listening level.Press the COMP control to activate
Volume/power controlPress the control to turn the audiosystem on or off.Turn control to raise or lowervolume.If the volume is set above a certain leve
Customer Assistance 175Reporting safety defects (U.S. only) 183Cleaning 184Maintenance and Specifications 190Engine compartment 192Engine oil 195Batte
Seek functionThe seek function control works inradio or CD mode.Seek function in radio mode• Pressto find the next listenable station down the frequen
AM/FM selectThe AM/FM select control works inradio, and CD modes (if equipped).Press the AM or FM control to enterinto radio mode.AM/FM select in radi
Setting the clockTo set the hour, press and hold thehour (H) control. When the desiredhour appears, release the control.To set the minute, press and h
• Press the CD control again to toggle between single CD mode and CDchanger mode (if available).Do not insert any promotional (odd shaped or sized) di
CD CHANGER (IF EQUIPPED)Your CD changer is either located in the trunk, the console or the rightside cargo area storage compartment.1. Slide the door
If you pull too hard on the disc holder, the disc holder may comecompletely out of the magazine. If this happens, reinsert the disc holderback into th
ONLY use the magazine supplied with the CD changer, other types willdamage the unit.Keep the CD changer door closed. Coins and foreign objects will da
CD units are designed to play commercially pressed 12 cm (4.75 in)audio compact discs only. Due to technical incompatibility, certainrecordable and re
RADIO RECEPTION FACTORSThree factors can affect radio reception:• Distance/strength. The further an FM signal travels, the weaker it is.The listenable
MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED)Fan speed controlControls the volume of air circulatedin the vehicle.Temperature control knobC
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
The air conditioning compressor can operate in all modes exceptand . However, the air conditioning will only function if the outsidetemperature is abo
• (Defrost) – Distributes outside air through the windshielddefroster ducts. It can be used to clear ice or fog from the windshield.If the temperature
To aid in side window defogging/demisting in cold weather conditions:1. Select the position that distributes air through the Panel and Floor.2. Set th
Turning the EATC onPress AUTO, any of the override controls or the fan speed control. TheEATC will only operate when the vehicle is running.Turning th
Temperature selectionThe display window indicates theselected temperature, function(AUTO or one of the overridecontrols) and manual control of fanspee
Fan speed ( )When AUTO is pressed, fan speed isadjusted automatically for existingconditions. You can override fanspeed at any time. To control fanspe
However, the air conditioning will only function if the outsidetemperature is about 6°C (43°F) or higher.Since the air conditioner removes considerabl
• OFF-Outside air is shut out and the fan will not operate. For shortperiods of time only, use this mode to reduce undesirable odors fromentering the
• If your vehicle has been parked with the windows closed during warmweather conditions, the air conditioner will perform more efficiently incooling t
CABIN AIR FILTER (IF EQUIPPED)Your vehicle may be equipped with a cabin air filter. This particulate airfiltration system is designed to reduce the co
Fuel pump shut-off switch In the event of an accident thesafety switch will automatically cut off the fuel supply to theengine. The switch can also be
HEADLAMP CONTROLRotate the headlamp control to thefirst position to turn on the parkinglamps.Rotate to the second position toturn on the headlamps.Aut
High beamsPush the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate.Flash to passPull toward you slightly to acti
AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident the alignment of yo
To see a clearer light pattern foradjusting, you may want to blockthe light from one headlamp whileadjusting the other.5. Locate the vertical adjuster
The dome lamp will stay on if thecontrol is moved to the passengerside position. When the control is inthe middle position, the lamp willonly come on
Rear dome lamp (if equipped)The dome lamp lights when:• any door is opened with thecontrol in the middle position.• the instrument panel dimmerswitch
Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an
Replacing headlamp bulbsTo remove the headlamp bulb:1. Make sure headlamp switch is inOFF position.2. Remove the bolt from theheadlamp housing.3. At t
5. Disconnect the electricalconnector from the bulb by pullingrearward.6. Remove the bulb retaining ring byrotating it counterclockwise.7. Remove the
2. Install the bulb retaining ring over the plastic base and lock the ringby rotating clockwise until it snaps into place.3. Connect the electrical co
BREAKING-IN YOUR VEHICLEThere are no particular guidelines for breaking-in your vehicle. Duringthe first 1,600 km (1,000 miles) of driving, vary speed
5. Carefully pull bulb straight out ofthe socket and push in the newbulb.6. Install the bulb socket into thelamp assembly by rotating itclockwise.7. C
Replacing high-mount brakelamp bulbs — Wagon only1. Open liftgate.2. Remove two screw covers, screwsand handle from liftgate.3. Remove two screws and
7. Carefully lift the lamp assemblyaway from the liftgate.8. Remove the bulb socket byrotating it counterclockwise andpulling it out from the lampasse
3. On the underside of the spoiler,remove the two decorative screwcovers (on the LED module).4. Remove the two screws that areholding the LED module i
Sedan1. Make sure headlamp switch is inOFF position and remove twoscrews, grommets and the licenseplate lamp assembly from the trunklid.2. Carefully p
6. Install the bulb socket into the lamp assembly by rotating it clockwise.7. Install the lamp assembly on the vehicle with three nut and washerassemb
WINDSHIELD WIPER/WASHER CONTROLSRotate the windshield wiper controlto the desired interval, low or highspeed position.The bars of varying length are f
Press the washer control to activatethe rear washer. The wiper willcome on when the washer control ispressed, if it is not already on.Windshield wiper
TILT STEERINGPull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredpo
POWER WINDOWSPress and hold the rocker switches to open and close windows.• Press the top portion of therocker switch to close.• Press the bottom port
MIDDLE EAST/NORTH AFRICA VEHICLE SPECIFIC INFORMATIONFor your particular global region, your vehicle may be equipped withfeatures and options that are
Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controlsexcept for the driver’s press
If highly magnetized items (such as magnetic mount antennas) areplaced very near the compass the display will change to “C” for 15seconds, then displa
Compass calibration adjustmentPerform this adjustment in an open area free from steel structures andhigh voltage lines.1. Start the vehicle.2. Press a
Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re
Do not use the speed control in heavy traffic or on roads thatare winding, slippery, or unpaved.To turn speed control off• Press OFF or• Turn off the
You can accelerate with the accelerator pedal at any time during speedcontrol usage. Releasing the accelerator pedal will return your vehicle tothe pr
To return to a previously set speed• Press RES. For RES to operate,the vehicle speed must be fasterthan 48 km/h (30 mph).Indicator lightThis light com
Use only soft cups in the cupholder. Hard objects can injure youin a collision.If your vehicle is equipped with the column shift and a bench seat, it
You will need a pocket adapter thatis compatible with your cellphone.The adapter will plug into thecenter console.To order your phone specific PocketA
TRUNK REMOTE CONTROL (IF EQUIPPED)Press the remote trunk releasecontrol on the instrument panel tothe left of the steering wheel.LIFTGATE (WAGON ONLY)
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
CARGO AREA FEATURESStorage compartmentYour vehicle comes equipped with astorage compartment in the floor ofthe cargo area. An additionalcompartment is
Do not place any objects on the cargo area cover. They mayobstruct your vision or strike occupants of the vehicle in thecase of a sudden stop or colli
The cover may cause injury in a sudden stop or accident if it isnot securely installed.Cargo utility hooks (Sedan)The utility hooks located in side th
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
To open the luggage compartmentdoor (lid) from within the luggagecompartment, pull the illuminated“T” shaped handle and push up onthe trunk lid. The h
The remote entry system allows you to lock or unlock all vehicle doors,trunk and liftgate without a key.The remote entry features only operate with th
Sounding a panic alarmPress this control to activate thealarm.To deactivate the alarm, press thecontrol again or turn the ignition toACC or ON.Panic a
To replace the battery:1. Twist a thin coin between the twohalves of the transmitter near thekey ring. DO NOT TAKE THEFRONT PART OF THETRANSMITTER APA
To program the transmitters yourself:• Place the key in the ignition andturn from 2 (LOCK) to 3 (OFF)and cycle between 3 (OFF) and 4(ON) eight times i
The system automatically turns off after 25 seconds or when the ignitionis turned to the ON or ACC position.The battery saver will shut off the exteri
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
Programming your own personal entry code1. Enter the factory-set code (keypad will illuminate when pressed).2. Press the 1/2 control within fivesecond
2. To unlock the passenger’s door(s)and liftgate (wagon), press the 3/4control within five seconds ofunlocking the driver’s door.3. To unlock the trun
Pressing the power door UNLOCK control button again will toggle theAutolock/Relock states.• Turn ignition to OFF to exit.SECURILOCK姟 PASSIVE ANTI-THEF
Key informationYour vehicle is supplied with two coded keys. Only a coded key willstart your vehicle. Spare coded keys can be purchased from yourdeale
Please read and understand the entire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition and turn the igni
The system is ready to arm whenever the key is removed from theignition. Any of the following actions will prearm the alarm system:• Press the remote
If the doors/hood or liftgate (wagon) are not closed and you press theremote entry transmitter twice to confirm the doors are locked, the hornwill chi
SEATINGAdjustable head restraintsYour vehicle’s seats are equipped with head restraints which arevertically adjustable. The purpose of these head rest
Adjusting the front manual seatNever adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the seatbacks to red
Adjusting the front power seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the sea
Commentaires sur ces manuels