Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 15Entertainment Systems 18AM/FM stereo 18AM/FM stereo cassette 22AM/FM stereo w
WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa
REAR SEATS2nd seat/split-folding rear seat (if equipped)One or both rear seatbacks can be folded down to provide additionalcargo space.To lower the se
3. Lift the remote latch release onthe left side of the compartmentand fold the remaining floor paneluntil it latches. Make sure theseatback is locked
How does the personal safety system work?The Personal Safety System can adapt the deployment strategy of yourvehicle’s safety devices according to cra
safety belt pretensioner activation depending upon safety belt usage.Refer to Safety Belt section in this chapter.Front safety belt pretensionersThe s
Safety belt precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce the risk of injury, mak
Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until
Vehicle sensitive modeThe vehicle sensitive mode is the normal retractor mode, allowing freeshoulder belt length adjustment to your movements and lock
• Grasp the shoulder portion andpull downward until the entirebelt is extracted.• Allow the belt to retract. As the belt retracts, you will hear a cli
Safety belt pretensionerYour vehicle is equipped with safety belt pretensioners at the driver andfront outboard passenger seating positions.The safety
Front safety belt height adjustmentYour vehicle has safety belt heightadjustments for the driver and frontpassenger. Adjust the height of theshoulder
If the light remains on, have your vehicle serviced at the firstavailable opportunity.Note: Thelight will illuminate if vehicle refueling is conducted
Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ
grasp the tongue so that it is parallel to the webbing and slide thetongue upward. Provide enough length so that the tongue can reach thebuckle.To fas
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignition switchis turned to the ON position...The safety belt wa
The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra
Reasons given... Consider...“I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to infla
To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle.1. Turn the ignition switch to the RUN (or O
Safety belt extension assemblyIf the safety belt is too short when fully extended, there is a 20 cm (8inch) safety belt extension assembly that can be
AIR BAG SUPPLEMENTAL RESTRAINT SYSTEMYour vehicle is equipped with a crash sensing and diagnostic modulewhich records information about the air bag an
The air bag supplemental restraints are an integral part of the PersonalSafety System. They are designed to be deployed in cases where thePersonal Saf
Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause thoseobjects to be propelled by the
when the ignition is moved from the ON position to START position, thelight will momentarily illuminate prior to reaching the START position).It also
How do the air bag supplemental restraints work?The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to noti
A difficulty with the system is indicated by one or more of the following:• The readiness light (same lightfor front and side air bag system)will eith
How does the side air bag system work?The side air bag system consists ofthe following:• An inflatable nylon bag (air bag)with a gas generator conceal
Several air bag systemcomponents get hot afterinflation. Do not touch them afterinflation.If the side air bag hasdeployed, the air bag willnot functio
Always follow the instructions and warnings that come with any infant orchild restraint you might use.When possible, always place children under age 1
Booster seats should be used until you can answer YES to ALL of thesequestions:• Can the child sit all the way backagainst the vehicle seat back withk
The shoulder belt should cross the chest, resting snugly on the center ofthe shoulder. The lap belt should rest low and snug across the hips,never up
When installing a child safety seat:• Review and follow the informationpresented in the Air BagSupplemental Restraint Systemsection in this chapter.•
1. Position the child safety seat in aseat with a combination lap andshoulder belt.Children 12 and under should be properly restrained in the rearseat
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
Charging systemIlluminates when the battery is notcharging properly.Engine oil pressureIlluminates when the oil pressurefalls below the normal range.
8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly tilt the seat forwardand back to m
The rear seats of your vehicle are equipped with built-in tether strapanchors located behind the seats as described below.The tether anchors in your v
5. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safetyseat may not be retained properlyin the even
Never attach two LATCH child safety seats to the same anchor.In a crash, one anchor may not be strong enough to hold twochild safety seat attachments
STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo
Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,
4. Make sure the parking brake isset.5. Turn the key to 4 (ON) withoutturning the key to 5 (START).If there is difficulty in turning thekey, firmly ro
Starting the engineNote: Whenever you start your vehicle, release the key as soon as theengine starts. Excessive cranking could damage the starter.1.
If you should experience cold weather starting problems on (Ed85)ethanol, and neither an alternative brand of (Ed85) ethanol nor anengine block heater
Have the exhaust and body ventilation systems checked whenever:• the vehicle is raised for service.• the sound of the exhaust system changes.• the veh
Check transaxleIlluminates when a transaxleproblem has been detected andshifting may be restricted. If thislamp remains on, have your vehicleserviced
Anti-lock brake system (ABS) (if equipped)On vehicles equipped with an anti-lock braking system (ABS), a noisefrom the hydraulic pump motor and pulsat
With the ABS light on, the anti-lockbrake system is disabled and normalbraking is still effective unless thebrake warning light also remainsilluminate
Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.Park brak
During Traction Controly operation,the traction control active light willilluminate, you may hear an electricmotor type of sound coming fromthe engine
• High crosswinds• Wheels out of alignment• Loose or worn suspension componentsAUTOMATIC TRANSMISSION OPERATIONBrake-shift interlockThis vehicle is eq
Do not rock the vehicle if the engine is not at normal operatingtemperature or damage to the transaxle may occur.Do not rock the vehicle for more than
If your vehicle is equipped with aconsole mounted gearshift, youmust press the thumb button on theside of the gearshift lever to movethe gearshift lev
R (Reverse)With the gearshift lever in R(Reverse), the vehicle will movebackward. You should always cometo a complete stop before shiftinginto and out
(Overdrive)The (Overdrive) position is thenormal driving position for anautomatic overdrive transaxle.When in the(Overdrive)position, the transaxle wo
1 (First)Use 1 (First) for when added enginebraking is desired when descendingsteep hills.The automatic transaxle will shift tothe proper gear to asce
Headlamps on warning chimeSounds when the headlamps or parking lamps are on, the key is removedfrom the ignition and the driver’s door is opened.Key-i
internal transmission damage. Have the fluid checked and, ifwater is found, replace the fluid.VEHICLE LOADINGBefore loading a vehicle, familiarize you
Do not exceed the GVWR or the GAWR specified on thecertification label.Do not use replacement tires with lower load carrying capacities than theorigin
The amount of weight that you can tow depends on the type of engine inyour vehicle. See the following charts:3.0L 2-Valve Vulcan EngineModel Passenger
Preparing to towUse the proper equipment for towing a trailer, and make sure it isproperly attached to your vehicle. See your dealer or a reliable tra
Driving while you towWhen towing a trailer:• Ensure that you turn off your speed control. The speed control mayshut off automatically when you are tow
RECREATIONAL TOWINGFollow these guidelines for your specific powertrain combination to towyour vehicle with all four wheels on the ground (such as beh
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will
If your vehicle is a sedan, the fuelpump shut-off switch is located onthe right side of the trunk behindthe trunk liner.If your vehicle is a wagon, th
FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth
This gauge indicates the temperature of the engine coolant, not thecoolant level. If the coolant is not at its proper level the gauge indicationwill n
Passenger compartment fuse panelThe fuse panel is located below and to the left of the steering wheel bythe brake pedal. Remove the panel cover to acc
Fuse/relaylocationFuse ampratingPassenger compartment fuse paneldescription13 20A Power point14 — Not used15 30A Front wiper motor16 15A Flasher and G
Fuse/relaylocationFuse ampratingPassenger compartment fuse paneldescription32 10A ABS, DRL relay coil, Speed controlactuator, Traction control switch,
To reduce risk of electrical shock, always replace the cover tothe Power Distribution Box before reconnecting the battery orrefilling fluid reservoirs
Fuse/relaylocationFuse ampratingPower distribution boxdescription15 20A* Anti-lock brake module valvesolenoid16 20A* Fuel pump relay17 20A* Cell port1
Temporary spare tire informationThe temporary spare tire for your vehicle is labeled as such. It is smallerthan a regular tire and is designed for eme
To prevent the vehicle from moving when you change a tire, besure the parking brake is set, then block (in both directions) thewheel that is diagonall
3. If equipped with a wheel coverthat’s bolted on, loosen the fiveplastic nuts with the lug nutwrench.4. Remove the center ornament or wheel cover fro
10. Remove the jack and fullytighten the lug nuts in the ordershown.11. Return the flat tire, jack and lugwrench to their proper storagelocations. Mak
Preparing your vehicleWhen the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, th
OdometerRegisters the total kilometers(miles) of the vehicle.Trip odometerRegisters the kilometers (miles) ofindividual journeys. To reset,depress the
2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat
4. Make the final connection of the negative (-) cable. Make theconnection to an exposed metal part of the stalled vehicle’s engine, awayfrom the batt
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center.It
GETTING THE SERVICES YOU NEEDAt homeFord Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you
Ford Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf you own a Lincoln vehicle and are away f
In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or
The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedu
What the Board needsTo have your case reviewed you must complete the application in theDSB brochure and mail it to the address provided on the applica
AM/FM STEREOVolume/power controlPress the control to turn the audiosystem on or off.Turn control to raise or lowervolume.If the volume is set above a
Every effort is made to decide the case within 40 days of the date thatall requested information is received by the Board. Since the Boardgenerally me
environment. These impartial arbitrators review the positions of theparties, make decisions and, when appropriate, render awards to resolvedisputes. C
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
2. Four or more repair attempts are made on the same nonconformity (adefect or condition that substantially impairs the use, value or safety ofthe veh
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Detail Wash (ZC-3–A), which is available
PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam
• 3.0L Vulcan engine• 3.0L Duratec engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PL
WINDOWS AND WIPER BLADESThe windshield, rear window and wiper blades should be cleanedregularly. If the wiper does not wipe properly, substances on th
INTERIORFor fabric, carpets, cloth seats, safety belts and seats equipped with sideair bags:• Remove dust and loose dirt with a vacuum cleaner.• Remov
WOOD-TONE TRIM• Clean the area with a damp cloth, then dry by wiping with a dry, soft,clean cloth.• Do not use household or glass cleaners as these ma
Bass/treble adjust• The bass adjust control allowsyou to increase or decrease theaudio system’s bass output.• The treble adjust control allowsyou to i
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
Working with the engine off1. Set the parking brake, and ensure the gearshift is securely latched in(P) park.2. Turn off the engine and remove the key
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.0L V6 Vulcan engine1. Automatic transmission fluid dipstick2. Brake fluid reservoir3. Air filter ass
3.0L DOHC V6 Duratec engine1. Automatic transmission fluid dipstick2. Brake fluid reservoir3. Air filter assembly4. Battery5. Engine oil dipstick6. En
WINDSHIELD WASHER FLUIDWasher fluidCheck the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with asymbol.If the level is low, add
Checking and adding washer fluid for the liftgate (if equipped)The opening for the reservoir islocated on the passenger side underthe tail lamp. Refil
5. Locate and carefully remove theengine oil indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.• If th
Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t
that does not meet Ford material and design specifications, start-upengine noises or knock may be experienced.It is recommended you use the appropriat
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a
Seating and Safety Restraints 97Seating 97Safety restraints 101Air bags 117Child restraints 123Driving 134Starting 134Brakes 139Traction control/Advan
AM/FM selectThe AM/FM select control works inradio mode. Press the AM or FMcontrol to enter radio mode.AM/FM select in radio modeThis control allows y
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “cold fill level” or within the “c
Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant couldmake it difficult to see through
For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when
Recycled engine coolantFord Motor Company recommends the use of a recycled engine coolantproduced by Ford-approved processes in vehicles originally eq
• Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may cause engine da
Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforefueling your vehicle.• Alwa
and sugar cane. When ethanol is used in the making of motor fuels, asmall amount of a bad tasting chemical is added to discourage beverageuse. The res
• DO NOT use a device that would hold the fuel pump handle in the fillposition.Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1
Choosing the right fuelUse only UNLEADED FUEL. The use of leaded fuel is prohibited by lawand could damage your vehicle.If your vehicle is a flexible
Setting the clockTo set the hour, press and hold thehour (H) control. When the desiredhour appears, release the control.To set the minute, press and h
Fuel qualityMany of the world’s automakersissued the World-wide Fuel Charterthat recommends gasolinespecifications to provide improvedperformance and
Cleaner airFord endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality.Running out of fuelAvoid running out of fuel becaus
Filling the tankThe advertised fuel capacity of the fuel tank on your vehicle is equal tothe rated refill capacity of the fuel tank as listed in the R
5. Follow one of the simple calculations in order to determine fueleconomy:Multiply liters used by 100, then divide by total kilometerstraveled.Divide
Maintenance• Keep tires properly inflated and use only recommended size.• Operating a vehicle with the wheels out of alignment will reduce fueleconomy
applicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproperly:• Use o
Readiness for Inspection/Maintenance (I/M) testingIn some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics sys
1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gauge indicator will benear the center
BRAKE FLUIDChecking and adding brake fluidBrake fluid should be checked andrefilled as needed. Refer to thescheduled maintenance guide forthe service
However, the fluid level should be checked if the transaxle is not workingproperly, i.e., if the transaxle slips or shifts slowly or if you notice som
MACHT AUDIO SYSTEM WITH AM/FM STEREO/CASSETTEVolume/power controlPress the control to turn the audiosystem on or off.Turn control to raise or lowervol
High fluid levelFluid levels above the safe rangemay result in transaxle failure. Anoverfill condition of transmissionfluid may cause shift and/orenga
space-saver or temporary use spare tires, tires with nominal rimdiameters of 10 to 12 inches or limited production tires as defined inTitle 49 Code of
The temperature grade for this tire is established for a tire thatis properly inflated and not overloaded. Excessive speed,underinflation, or excessiv
Replacing the tiresReplace the tires when the wearband is visible through the tiretreads.When replacing full size tires, never mix radial bias-belted,
Follow these guidelines when using snow tires and chains:• Use only cable type chains offered by Ford as an accessory orequivalent. SAE class “S” or o
3If a spark plug is to be removed for inspection, it must be reinstalled inthe same cylinder. If a spark plug needs to be replaced, use only sparkplug
Fluid Ford PartNameApplication CapacityAutomatictransaxle -4F50NMotorcraftMERCONtVATF3.0L V6 Vulcanengine12.8L (13.5quarts)3.0L V6 Duratecengine12.7L
ItemsFord PartName orequivalentFord PartNumberFordSpecificationLock cylinders Penetrating andLock LubricantMotorcraft XL-1 noneAutomatictransaxle (AX4
Some transmission fluids may be labeled as dual usage, such asMERCONt and MERCONt V. These dual usage fluids are not to be usedin an automatic transmi
52341Maintenance and Specifications229
Bass/treble adjust• The bass adjust control allowsyou to increase or decrease theaudio system’s bass output.• The treble adjust control allowsyou to i
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
Vehicle identification numberThe vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Please not
FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincol
Travel equipmentElectrochromic inside mirror with compassElectrochromic inside mirror with compass and temperatureEmergency kitFactory luggage rack ad
For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle:• When adding accessories,
AABS (see Brakes) ...140Accessory delay ...70Air bag supplemental restraintsystem ...117
attaching with tether straps ..130in front seat ...127in rear seat ...127, 130Cleaning your vehicleengine
Engine oil ...195checking and adding ...195dipstick ...195filter, specifica
IIgnition ...134, 228Infant seats(see Safety seats) ...126Inspection/maintenance (I/M)testing ...
automatic dimming rearviewmirror ...70heated ...73side view mirrors (power)
Scan functionThe scan function works in radio,tape or CD mode.Scan function in radio modePress the SCAN control to hear a brief sampling of all listen
Spark plugs,specifications ...224, 228Specification chart,lubricants ...226, 228Speed control ...
Radio station memory presetThe radio is equipped with six station memory preset controls. Thesecontrols can be used to select up to six preset AM stat
Tune adjust in radio mode• Press to move to the next frequency down the band (whether ornot a listenable station is located there). Hold the control t
RewindThe rewind control works in tapeand CD modes.• In tape mode, radio play willcontinue until rewind is stopped(with the TAPE or REW control) or th
Compression adjustCompression adjust brings soft andloud CD passages together for amore consistent listening level.Press the COMP control to activate
Volume/power controlPress the control to turn the audiosystem on or off.Turn control to raise or lowervolume.If the volume is set above a certain leve
Cleaning 184Maintenance and Specifications 190Hood 191Engine compartment 192Engine oil 195Battery 198Fuel information 205Part numbers 224Refill capaci
Seek functionThe seek function control works inradio or CD mode.Seek function in radio mode• Press to find the next listenable station down the freque
AM/FM selectThe AM/FM select control works inradio, and CD modes (if equipped).Press the AM or FM control to enterinto radio mode.AM/FM select in radi
Setting the clockTo set the hour, press and hold thehour (H) control. When the desiredhour appears, release the control.To set the minute, press and h
• To begin CD play, press the CD control. The first track of the first discwill begin playing. After that CD play will begin where it stopped last.• P
CD CHANGER (IF EQUIPPED)Your CD changer is either located in the trunk, the console or the rightside cargo area storage compartment.1. Slide the door
If you pull too hard on the disc holder, the disc holder may comecompletely out of the magazine. If this happens, reinsert the disc holderback into th
The CD magazine may be inserted or ejected with the radio power off.ONLY use the magazine supplied with the CD changer, other types willdamage the uni
CD units are designed to play commercially pressed 12 cm (4.75in) audio compact discs only. Due to technical incompatibility,certain recordable and re
RADIO RECEPTION FACTORSThree factors can affect radio reception:• Distance/strength. The further an FM signal travels, the weaker it is.The listenable
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)Fan speed controlControls the volume of air circulatedin the vehicle.Temperature control knobCo
The following warning may be required by California law:CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain
The air conditioning compressor can operate in all modes exceptand . However, the air conditioning will only function if the outsidetemperature is abo
• (Defrost) – Distributes outside air through the windshielddefroster ducts. It can be used to clear ice or fog from the windshield.If the temperature
To aid in side window defogging/demisting in cold weather conditions:1. Select the position that distributes air through the Panel and Floor.2. Set th
Turning the EATC onPress AUTO, any of the override controls or the fan speed control. TheEATC will only operate when the vehicle is running.Turning th
Temperature selectionThe display window indicates theselected temperature, function(AUTO or one of the overridecontrols) and manual control of fanspee
Fan speed ( )When AUTO is pressed, fan speed isadjusted automatically for existingconditions. You can override fanspeed at any time. To control fanspe
However, the air conditioning will only function if the outsidetemperature is about 6°C (43°F) or higher.Since the air conditioner removes considerabl
• OFF-Outside air is shut out and the fan will not operate. For shortperiods of time only, use this mode to reduce undesirable odors fromentering the
• If your vehicle has been parked with the windows closed during warmweather conditions, the air conditioner will perform more efficiently incooling t
CABIN AIR FILTER (IF EQUIPPED)Your vehicle may be equipped with a cabin air filter. This particulate airfiltration system is designed to reduce the co
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury and prevent possibledamage to others, you
HEADLAMP CONTROLRotate the headlamp control to thefirst position to turn on the parkinglamps.Rotate to the second position toturn on the headlamps.Aut
High beamsPush the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate.Flash to passPull toward you slightly to acti
AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident the alignment of yo
To see a clearer light pattern foradjusting, you may want to blockthe light from one headlamp whileadjusting the other.5. Locate the vertical adjuster
The dome lamp will stay on if thecontrol is moved to the passengerside position. When the control is inthe middle position, the lamp willonly come on
Rear dome lamp (if equipped)The dome lamp lights when:• any door is opened with thecontrol in the middle position.• the instrument panel dimmerswitch
Function Number of bulbsTrade numberFront park/turn lamp 23457 AK(amber)Headlamp 29007 QL(9007 LLoptional)Tail lamp/brake/turn lamp 2 3057KTail lamp/b
Replacing headlamp bulbsTo remove the headlamp bulb:1. Make sure headlamp switch is inOFF position.2. Remove the bolt from theheadlamp housing.3. At t
5. Disconnect the electricalconnector from the bulb by pullingrearward.6. Remove the bulb retaining ring byrotating it counterclockwise.7. Remove the
2. Install the bulb retaining ring over the plastic base and lock the ringby rotating clockwise until it snaps into place.3. Connect the electrical co
BREAKING-IN YOUR VEHICLEThere are no particular guidelines for breaking-in your vehicle. Duringthe first 1 600 km (1 000 miles) of driving, vary speed
5. Carefully pull bulb straight out ofthe socket and push in the newbulb.6. Install the bulb socket into thelamp assembly by rotating itclockwise.7. C
Replacing high-mount brakelamp bulbs — Wagon only1. Open liftgate.2. Remove two screw covers, screwsand handle from liftgate.3. Remove two screws and
7. Carefully lift the lamp assemblyaway from the liftgate.8. Remove the bulb socket byrotating it counterclockwise andpulling it out from the lampasse
3. On the underside of the spoiler,remove the two decorative screwcovers (on the LED module).4. Remove the two screws that areholding the LED module i
Sedan1. Remove two screws, grommetsand the license plate lamp assemblyfrom the trunk lid.2. Carefully pull the bulb from thesocket and push in the new
4. Remove the bulb socket byrotating it counterclockwise, thenpulling it out of the lamp assembly.5. Pull the bulb from the socket andpush in the new
WINDSHIELD WIPER/WASHER CONTROLSRotate the windshield wiper controlto the desired interval, low or highspeed position.The bars of varying length are f
Press the washer control to activatethe rear washer. The wiper willcome on when the washer control ispressed, if it is not already on.Windshield wiper
TILT STEERINGPull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredpo
Do not plug optional electrical accessories into the cigarettelighter. Use the power point.POWER WINDOWSPress and hold the rocker switches to open and
Please read the section Air bag in the Seating and safetyrestraints chapter. Failure to follow the specific warnings andinstructions could result in p
Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controlsexcept for the driver’s press
If highly magnetized items (such as magnetic mount antennas) areplaced very near the compass the display will change to “C” for 15seconds, then displa
Compass calibration adjustmentPerform this adjustment in an open area free from steel structures andhigh voltage lines.1. Start the vehicle.2. Press a
Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re
Do not use the speed control in heavy traffic or on roads thatare winding, slippery, or unpaved.To turn speed control off• Press OFF or• Turn off the
To set a higher set speed• Press and hold SET +. Releasethe control when the desiredvehicle speed is reached or• Press and release SET + tooperate the
Pressing OFF will erase thepreviously programmed set speed.To return to a previously set speed• Press RES. For RES to operate,the vehicle speed must b
• Compact disc changer (if equipped)• Tissue holder• Rear A/C vent• Rear ashtray (see your Ford, Lincoln Mercury dealer to obtain rearashtrayUse only
You will need a pocket adapter thatis compatible with your cellphone.The adapter will plug into thecenter console.To order your phone specific PocketA
TRUNK REMOTE CONTROL (IF EQUIPPED)Press the remote trunk releasecontrol on the instrument panel tothe left of the steering wheel.LIFTGATE (WAGON ONLY)
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
CARGO AREA FEATURESStorage compartmentYour vehicle comes equipped with astorage compartment in the floor ofthe cargo area. An additionalcompartment is
Do not place any objects on the cargo area cover. They mayobstruct your vision or strike occupants of the vehicle in thecase of a sudden stop or colli
The cover may cause injury in a sudden stop or accident if it isnot securely installed.Cargo utility hooks (Sedan)The utility hooks located in side th
KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w
To open the luggage compartmentdoor (lid) from within the luggagecompartment, pull the illuminated“T” shaped handle and push up onthe trunk lid. The h
Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment.The rem
Sounding a panic alarmPress this control to activate thealarm.To deactivate the alarm, press thecontrol again or turn the ignition toACC or ON.Panic a
1. Twist a thin coin between the twohalves of the transmitter near thekey ring. DO NOT TAKE THEFRONT PART OF THETRANSMITTER APART.2. Place the positiv
• Within 20 seconds, program a remote transmitter by pressing anybutton on a transmitter. The doors will lock/unlock to confirm that theremote transmi
Deactivating/activating perimeter lampsThere are 2 methods to enable/disable this feature. One through yourdealer and the second with a power door loc
Vehicle Symbol GlossaryPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic AlarmEngine Oil Engine CoolantEn
Programming your own personal entry code1. Enter the factory-set code (keypad will illuminate when pressed).2. Press the 1/2 control within fivesecond
1. To unlock the driver’s door, enter one of the two codes. After pressingthe fifth number, the driver’s door unlocks.2. To unlock the passenger’s doo
Pressing the power door UNLOCK control button again will toggle theAutolock/Relock states.• Turn ignition to OFF to exit.SECURILOCKY PASSIVE ANTI-THEF
dealership. Your dealership can program your key or you can “do ityourself.” Refer to Programming spare keys.Certain items may cause vehicle starting
Please read and understand the entire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition and turn the igni
The system is ready to arm whenever the key is removed from theignition. Any of the following actions will prearm the alarm system:• Press the remote
If the doors/hood or liftgate (wagon) are not closed and you press theremote entry transmitter twice to confirm the doors are locked, the horn willchi
SEATINGAdjustable head restraintsYour vehicle’s seats are equipped with head restraints which arevertically adjustable. The purpose of these head rest
Adjusting the front manual seatNever adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the seatbacks to red
Adjusting the front power seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the sea
Commentaires sur ces manuels