Introduction 3Instrument Cluster 10Warning and control lights 10Gauges 15Entertainment Systems 19AM/FM stereo cassette with CD 19AM/FM stereo with CD
WARNING LIGHTS AND CHIMESBase instrument clusterOptional instrument clusterTurn signalsIlluminates when theturn signals or thehazard lights areturned
Reclining the seatback can cause anoccupant to slide under the seat’s safetybelt, resulting in severe personal injuries in theevent of a collision.The
outboard back of the seat. The seatback locksautomatically when returned to the normal position.The rotating boot on the front seat belt is designedto
To reduce the risk of injury, make surechildren sit where they can be properlyrestrained.Never let a passenger hold a child on his orher lap while the
Always transport children 12 years old andunder in the back seat and always properlyuse appropriate child restraints.Combination lap and shoulder belt
positions to help further reduce the risk of injuryin the event of a head-on collision.• This safety belt system has a retractor assemblythat is desig
Automatic locking modeIn this mode, the shoulder belt is automaticallypre-locked. The belt will still retract to remove anyslack in the shoulder belt.
• Grasp the shoulderportion and pulldownward until theentire belt isextracted.• Allow the belt to retract. As the belt retracts, youwill hear a clicki
BELT AND RETRACTOR ASSEMBLY MUSTBE REPLACED if the seat belt assembly“automatic locking retractor” feature or any otherseat belt function is not opera
If... Then...The driver’s safety belt is notbuckled approximately 5seconds after the safety beltwarning light has turnedoff...The BeltMinder feature i
Reasons given... Consider...“I was in a hurry” Prime time for an accident.BeltMinder reminds us to take a fewseconds to buckle up.“Seat belts don’twor
Charging systemIlluminates when thebattery is not chargingproperly.Air bag readinessIlluminates to confirmthat the air bags (frontor side) areoperatio
The BeltMinder feature can be deactivated/activatedby performing the following procedure:Before following the procedure, make sure that:• The parking
7. Confirmation of disabling BeltMinder is providedby the safety belt warning light flashing four timesper second for three seconds.8. Confirmation of
bracket assemblies (if equipped), LATCH child seattether anchors and lower anchors (if equipped), andattaching hardware, should be inspected after aco
and in helping to better understand real worldcollisions and further improve the safety of futurevehicles.Important supplemental restraint system (SRS
Steps you can take to properly position yourselfaway from the air bag:• Move your seat to the rear as far as you can whilestill reaching the pedals co
positions than in the front seating position. Failureto follow these instructions may increase the risk ofinjury in a collision.Air bags can kill or i
The air bags inflate anddeflate rapidly uponactivation. After air bagdeployment, it isnormal to notice asmoke-like, powderyresidue or smell theburnt p
system wiring, the air bag system readiness light, theair bag back up power and the air bag ignitors.Several air bag system components get hotafter in
SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how toproperly use safety restraints for children. Also seeAir bag suppleme
If the shoulder belt portion of a combination lap andshoulder belt can be positioned so it does not crossor rest in front of the child’s face or neck,
recommended octane and/or properly installing andsecurely tightening the fuel cap. After three drivingcycles without these or any other temporarymalfu
Booster seats should be used until you can answerYES to ALL of these questions:• Can the child sit allthe way back againstthe vehicle seat backwith kn
• Those with a highback.If, with a backlessbooster seat, youcannot find a seatingposition thatadequately supportsyour child’s head, ahigh back booster
SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the sizeand weight of the child. Carefully fo
• Keep the buckle release button pointing up andaway from the safety seat, with the tonguebetween the child seat and the release button, toprevent acc
Air bags can kill or injure a child in a childseat. NEVER place a rear-facing child seatin front of an active air bag. If you must use aforward-facing
4. Insert the belttongue into the properbuckle (the buckleclosest to the directionthe tongue is comingfrom) for that seatingposition until you heara s
9. Before placing thechild in the seat,forcibly move the seatforward and back tomake sure the seat issecurely held in place.To check this, grab thesea
The tether strap anchors in your vehicle are in thefollowing positions (shown from top view):Attach thetether straponly to theappropriate tetheranchor
5. Clip the tether strapto the anchor asshown.For Convertible only:The tether anchors onthe convertible arelocated on the lowerbackside of theseatback
6. Refer to the Installing child safety seats incombination lap and shoulder belt seatingpositions section of this chapter for furtherinstructions to
Low fuelIlluminates when thefuel level in the fueltank is at, or near,empty (refer to Fuelgauge in this chapter for more information).O/D off (if equi
STARTINGPositions of the ignition1. ACCESSORY, allowsthe electricalaccessories such as theradio to operate whilethe engine is notrunning. For manualtr
When starting a fuel-injected engine, avoid pressingthe accelerator before or during starting. Only usethe accelerator when you have difficulty starti
Before starting the vehicle:1. Make sure all vehicle occupants have buckledtheir safety belts. For more information on safetybelts and their proper us
• steering wheel is turned when getting in or out ofthe vehicleMake sure the corresponding lights illuminate orilluminate briefly. If a light fails to
Starting the engineNote: Whenever you start your vehicle, release thekey as soon as the engine starts. Excessive crankingcould damage the starter.1. T
To prevent electrical shock, do not use yourheater with ungrounded electrical systemsor two-pronged (cheater) adapters.Guarding against exhaust fumesA
Adjust the heating or air conditioning (if equipped)to bring in fresh air.Improve vehicle ventilation by keeping all air inletvents clear of snow, lea
The BRAKE warninglamp in the instrumentcluster illuminates andremains illuminated(when the ignition is turned ON) until the parkingbrake is released.A
self-check after you start the engine and begin todrive away. A brief mechanical noise may be heardduring this test. This is normal. If a malfunction
and, providing there is sufficient space, willenable you to avoid obstacles and bring thevehicle to a controlled stop.• The anti-lock system does not
illuminated and parking brake is off. Refer to Brakesin the Driving chapter for more information.Brake system warningTo confirm the brakesystem warnin
If the power steering system breaks down (or if theengine is turned off), you can steer the vehiclemanually, but it takes more effort.If the steering
During TractionControly operation,the traction controlactive light willilluminate, you may hear an electric motor type ofsound coming from the engine
AUTOMATIC TRANSMISSION OPERATION(IF EQUIPPED)Brake-shift interlockThis vehicle is equipped with a brake-shift interlockfeature that prevents the gears
Always set the parking brake fully and makesure the gearshift is latched in P (Park).Turn the ignition to the LOCK position and removethe key whenever
Driving with a 4–speed automatic transmission(if equipped)Use the followingprocedure to put yourvehicle in gear.1. Start the engine.2. Depress and hol
R (Reverse)With the gearshift leverin R (Reverse), thevehicle will movebackward. Always cometo a complete stopbefore shifting into andout of R (Revers
(Overdrive) can bedeactivated by pressingthe transmissioncontrol switch on thegearshift lever.The transmissioncontrol indicator light(TCIL) will illum
2 (Second)Use 2 (Second) tostart-up on slipperyroads or to provideadditional enginebraking on downgrades.Transmission operatesonly in Second gear.1 (F
When starting a vehicle with a manual transmission,you must:1. Make sure theparking brake is fullyset.2. Depress the clutchpedal fully.3. Put the gear
Upshift according to the following chart:Upshifts when accelerating (recommended for bestfuel economy)Shift from:1 - 2 18 km/h (11 mph)2 - 3 31 km/h (
Headlamps on warning chimeSounds when the headlamps or parking lamps areon, the key is removed from the ignition and thedriver’s door is opened.GAUGES
Do not park your vehicle in Neutral, it maymove unexpectedly and injure someone. Use1 (First) gear and set the parking brake fully.ReverseYou must be
Removing key from ignition• Turn the ignition keyto position 3 (OFF).• Push the releaselever forward androtate the keytowards you andremove.DRIVING TH
• Payload: Combined maximum allowable weight ofcargo, occupants and optional equipment. Thepayload equals the gross vehicle weight ratingminus base cu
Remember to figure in the tongue load of yourloaded trailer when figuring the total weight.Do not exceed the GVWR or the GAWRspecified on the certific
RECREATIONAL TOWING (ALL WHEELS ONTHE GROUND)Follow these guidelines for your specific powertraincombination to tow your vehicle with all four wheelso
GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicleconcern, Ford Motor Company offers acomplimentary roadside assistance program.
portfolio in the glove compartment in Ford vehiclesand is mailed to you if you own a Mercury orLincoln. In Canada, the card is found in the OwnerInfor
• The hazard lightscontrol is located ontop of the steeringcolumn.• Depress hazardlights control toactivate all hazardflasherssimultaneously.• Depress
FUSES AND RELAYSFusesIf electricalcomponents in thevehicle are notworking, a fuse mayhave blown. Blownfuses are identified by a broken wire within the
To remove a fuse use the fuse puller tool providedon the fuse panel cover.The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPassenger Com
Never remove the coolant reservoir capwhile the engine is running or hot. Steamand scalding liquid from a hot cooling system canburn you badly.This ga
Fuse/RelayLocationFuse AmpRatingPassenger CompartmentFuse Panel Description16 — Not used17 15A Speed control servo, Shiftlock actuator18 15A Electroni
Fuse/RelayLocationFuse AmpRatingPassenger CompartmentFuse Panel Description39 5A GEM40 — Not used41 15A Brake lamp42 — Not used43 20A CB Power windows
The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescriptionRelay 1 — Fog lamp interruptRelay 2 — Int
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription11 30A** Rear window defrost control12 40A** Power windows, Powerlocks13 30A* MACH 10
for emergency use only. Replace this tire with afull-size tire as soon as possible.If you use the temporary spare tirecontinuously or do not follow th
If the vehicle slips off the jack, you orsomeone else could be seriously injured.1. Park on a levelsurface, activate hazardflashers and setparking bra
5. Put the jack in thejack notch next to thetire you are changing.Turn the jack handleclockwise until thewheel is completely offthe ground.Never use t
9. Remove the jack andfully tighten the lugnuts in the ordershown.10. Put flat tire, wheelornament (if equipped),jack and lug wrenchaway. Make sure ja
JUMP STARTING YOUR VEHICLEThe gases around the battery can explode ifexposed to flames, sparks, or lit cigarettes.An explosion could result in injury
Connecting the jumper cables1. Connect the positive (+) booster cable to thepositive (+) terminal of the discharged battery.Note: In the illustrations
When refueling the vehicle from empty indication,the amount of fuel that can be added will be lessthan the advertised capacity due to the reserve fuel
4. Make the final connection of the negative (-)cable to an exposed metal part of the stalledvehicle’s engine, away from the battery and thecarburetor
Removing the jumper cablesRemove the jumper cables in the reverse orderthat they were connected.1. Remove the jumper cable from the ground metalsurfac
4. Remove the jumper cable from the positive (+)terminal of the disabled vehicle’s battery.After the disabled vehicle has been started and thejumper c
WRECKER TOWINGIf you need to have your vehicle towed, contact aprofessional towing service or, if you are a member,your roadside assistance center.It
GETTING THE SERVICES YOU NEEDAt homeFord Motor Company and Ford of Canada haveauthorized dealerships to service your vehicle. It ispreferred that you
In the United States:Ford Motor CompanyCustomer Relationship Center16800 Executive Plaza DriveP.O. Box 6248Dearborn, Michigan 481211-800-392-3673 (FOR
In order to help you service your Ford or LincolnMercury vehicle, please have the followinginformation available when contacting a CustomerRelationshi
• Protection against covered repair costs after yourBumper-to-Bumper Warranty expires.You may purchase Ford ESP from any participatingFord and Lincoln
Mercury cars and Ford and Lincoln Mercury lighttrucks which are within the terms of any applicablewritten new vehicle warranty are eligible for review
Consumer candidates for Board membership arerecruited and trained by an independent consultingfirm. The dealership Board member is chosen fromFord and
• Base instrumentcluster gauge• Optional instrumentcluster gaugeTrip odometerRegisters thekilometers (miles) ofindividual journeys.Press and release t
• A description of the action you expect to resolveyour concern.You will receive a letter of explanation if yourapplication does not qualify for Board
You may also contact the North American CustomerRelationship Center at 1-800-392-3673 (Ford), TDDfor the hearing impaired: 1-800-232-5952 or bywriting
consulate. These officials can inform you of localvehicle registration regulations and where to findunleaded fuel.If you cannot find unleaded fuel or
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contactHelm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detroi
2. Four or more repair attempts are made on thesame nonconformity (a defect or condition thatsubstantially impairs the use, value or safety of thevehi
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarmwater and a neutral Ph shampoo, such as DetailWash (ZC-3–A), which is available f
PAINT CHIPSYour dealer has touch-up paint and sprays to matchyour vehicle’s color. Take your color code (printedon a sticker in the driver’s door jam)
• Do not spray with cold water to avoid crackingthe engine block or other engine components.• Spray Engine Shampoo and Degreaser(F4AZ-19A536–A) on all
PLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts.These products are available from your dealer.• For routine clea
• Be certain to wash or wipe your hands clean ifyou have been in contact with certain productssuch as insect repellent and suntan lotion in orderto av
PREMIUM AM/FM STEREO/CASSETTE/SINGLECDVolume/power controlPress the control toturn the audio systemon or off.Audio power can alsobe turned on bypressi
CONVERTIBLE TOP AND PADDED MOLDINGCAREWash with Triple Clean (EOAZ-19526–AA), which isavailable from your dealer.• Do not use stiff bristle brushes or
Ford Extra Strength Upholstery Cleaner (notavailable in Canada)Ford Custom Bright Metal CleanerMotorcraft Premium Car Wash ConcentrateMotorcraft Carli
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the enginecompartment for easy location.• We provide a
3. Block the wheels to prevent the vehicle frommoving unexpectedly.• Manual transmission:1. Set the parking brake.2. Depress the clutch and place the
OPENING THE HOOD1. Inside the vehicle,pull the hood releasehandle located underthe bottom left cornerof the instrumentpanel.2. Go to the front of the
IDENTIFYING COMPONENTS IN THE ENGINECOMPARTMENT3.8L OHV V6 engine1. Engine oil filler cap2. Engine oil dipstick3. Brake fluid reservoir4. Power distri
4.6L SOHC V8 engine1. Engine oil dipstick2. Brake fluid reservoir3. Power distribution box4. Windshield washer fluid reservoir5. Battery6. Engine cool
WINDSHIELD WASHER FLUIDWasher fluidCheck the washer fluidwhenever you stop forfuel. The reservoir ishighlighted with asymbol.If the level is low, adde
4. Open the hood. Protect yourself from engine heat.5. Locate and carefully remove the engine oil levelindicator (dipstick).• 3.8L V6 engine• 4.6L SOH
• 3.8L V6 engine• 4.6L SOHC V8engine• Oil levels above the MAX mark may cause enginedamage. Some oil must be removed from theengine by a service techn
Roadside Emergencies 157Getting roadside assistance 157Hazard flasher switch 158Fuel pump shut-off switch 159Fuses and relays 160Changing tires 165Jum
Press the BASS control then press:•to decrease thebass output and•to increase thebass output.Treble adjustThe treble adjustcontrol allows you toincrea
5. Fully install the engine oil filler cap by turning thefiller cap clockwise 1/4 of a turn until three clicksare heard or until the cap is fully seat
BATTERYYour vehicle isequipped with aMotorcraftmaintenance-freebattery which normallydoes not requireadditional water duringits life of service.Howeve
Batteries normally produce explosive gaseswhich can cause personal injury. Therefore,do not allow flames, sparks or lighted substancesto come near the
3. Run the engine until it reaches normal operatingtemperature.4. Allow the engine to idle for at least one minute.5. Turn the A/C on and allow the en
ENGINE COOLANTChecking engine coolantThe concentration and level of engine coolant shouldbe checked at the mileage intervals in the scheduledmaintenan
• 4.6L SOHC V8engineWhen the engine is cold, check the level of theengine coolant in the reservoir.• The engine coolant should be at the “cold filllev
Do not put engine coolant in the windshieldwasher fluid container. If sprayed on thewindshield, engine coolant could make it difficultto see through t
water as soon as possible. Water alone (withoutengine coolant) can cause engine damage fromcorrosion, overheating or freezing.• Do not use alcohol, me
The following procedure should be used whenrefilling the cooling system of a 3.8L V6 engine afterit has been drained or become extremely low.1. Remove
Engine coolant refill procedure-4.6L V8 engineThe following procedure should be used whenrefilling the cooling system of a 4.6L V8 engine afterit has
Press the FADE control then press:•to shift thesound to the frontand•to shift the sound to the rear.Seek functionThe seek function control works in ra
enough 50/50 concentration of engine coolant anddistilled water to bring the liquid level to the properlevel.If you have to add more than 1.0 liter (1
• NEVER increase the coolant concentrationabove 60%.• Increased engine coolant concentrationsabove 60% will decrease the overheatprotection characteri
WHAT YOU SHOULD KNOW ABOUTAUTOMOTIVE FUELSImportant safety precautionsDo not overfill the fuel tank. The pressure inan overfilled tank may cause leaka
injury. If fuel is swallowed, call a physicianimmediately, even if no symptoms are immediatelyapparent. The toxic effects of fuel may not bevisible fo
Use the following guidelines to avoid static build-upwhen filling an ungrounded fuel container:• Place approved fuel container on the ground.• DO NOT
The fuel system may be under pressure. Ifthe fuel filler cap is venting vapor or if youhear a hissing sound, wait until it stops beforecompletely remo
Fuel qualityIf you are experiencing starting, rough idle orhesitation driveability problems during a cold start,try a different brand of “Regular” unl
If you have run out of fuel:• You may need to cycle the ignition from OFF toON several times after refueling, to allow the fuelsystem to pump the fuel
Indicated capacity is the difference in the amount offuel in a full tank and a tank when the fuel gaugeindicates empty. Empty reserve is the small amo
4. Subtract your initial odometer reading from thecurrent odometer reading.5. Follow one of the simple calculations in order todetermine fuel economy:
Scan functionThe scan functionworks in radio, tape orCD mode.Scan function in radio modePress the SCAN control to hear a brief sampling ofall listenab
• Using the air conditioner or defroster may reducefuel economy.• You may want to turn off the speed control inhilly terrain if unnecessary shifting b
• Driving on flat terrain offers improved fueleconomy as compared to driving on hilly terrain.• Transmissions give their best fuel economy whenoperate
service of components affecting emission control,such non-Ford parts should be equivalent to genuineFord Motor Company parts in performance anddurabil
If the vehicle’s powertrain system or its battery hasjust been serviced, the on-board diagnostics systemis reset to a “not ready for I/M test” conditi
2. While the engine idles, turn the steering wheelleft and right several times.3. Turn the engine off.4. Check the fluid level on the dipstick. It sho
• 3.8L OHV V6 engine• 4.6L SOHC V8engine1. Clean the reservoir cap before removal to preventdirt or water from entering the reservoir.2. Visually insp
Brake fluid is toxic. If brake fluid contactsthe eyes, flush eyes with running water for15 minutes. Seek medical attention if irritationpersists. If t
the fluid level should be checked if the transmissionis not working properly, i.e., if the transmission slipsor shifts slowly or if you notice some si
Correct fluid levelThe transmission fluid should be checked at normaloperating temperature 66°C-77°C (150°F-170°F) ona level surface. The normal opera
If an overfill occurs,excess fluid should beremoved by a qualifiedtechnician.An overfill condition of transmission fluid maycause shift and/or engagem
Radio station memory presetThe radio is equipped with six station memorypreset controls. These controls can be used to selectup to six preset AM stati
INFORMATION ABOUT UNIFORM TIRE QUALITYGRADINGNew vehicles are fittedwith tires that have arating on them calledTire Quality Grades.The Quality grades
Traction AA A B CThe traction grades, from highest to lowest are AA,A, B, and C. The grades represent the tire’s ability tostop on wet pavement as mea
SERVICING YOUR TIRESChecking the tire pressure• Use an accurate tire pressure gauge.• Check the tire pressure when tires are cold, afterthe vehicle ha
• 17 inch four tirerotationReplacing the tiresReplace the tires whenthe wear band is visiblethrough the tire treads.When replacing full size tires, ne
Make sure that all replacement tires are ofthe same size, type, load-carrying capacityand tread design (e.g., “All Terrain”, “Touring”,etc.), as origi
• Drive cautiously. If you hear the chains rub orbang against your vehicle, stop and re-tighten thechains. If this does not work, remove the chainsto
REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid MotorcraftHighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to line onreservoir
Fluid Ford PartNameApplication CapacityFuel tank N/A All 59.4L (15.7gallons)Transmissionfluid3MotorcraftMERCONtVATFAutomaticwith 3.8LOHV V6engine13.1L
4Indicates only approximate dry-fill capacity. Someapplications may vary based on cooler size and ifequipped with an in-tank cooler. The amount oftran
Item Ford partnameFord partnumberFordspecificationEnginecoolantMotorcraftPremiumEngineCoolant(green-colored)VC-4–A (US)or CXC-10(Canada)ESE-M97B44-AMo
If there are less than six strong stations available onthe frequency band, the remaining memory presetcontrols will all store the last strong stationa
Item Ford partnameFord partnumberFordspecification3.8L ManualtransmissionfluidMotorcraftMERCONtATFXT-2-QDX MERCONt4.6L ManualtransmissionfluidMotorcra
ENGINE DATAEngine 3.8L OHV V6engine4.6L SOHC V8engineCubic inches 232 281Required fuel 87 octane 87 octaneFiring order 1-4-2-5-3-6 1-3-7-2-6-5-4-8Spar
IDENTIFYING YOUR VEHICLECertification labelThe National HighwayTraffic SafetyAdministrationRegulations requirethat a Certificationlabel be affixed to
Vehicle identification numberThe vehicleidentification number isattached to a metal tagand is located on thedriver side instrumentpanel. (Please notet
FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of genuine Ford accessories areavailable for your vehicle through your local authorizedFord, Lincoln
Dash trimElectrochromic mirror with compassElectrochromic mirror with compass andtemperature displayEngine block heatersRemote keyless entry systemRem
Side air deflectorSpoilerStyled hood deflectorTonneau cover (mini, for convertible top)Universal floor matsWheels (chrome and painted)For maximum vehi
AABS (see Brakes) ... 137Air bag supplementalrestraintsystem ... 112–113and child safetyseats ... 114description ...
Bulbs ... 69CCapacities forrefilling fluids ... 236Cargo net ... 77CD player ... 42–43CD-single
The DisputeSettlementBoard ... 177Utilizing theMediation/ArbitrationProgram ... 181DDaytime running lamps(see Lamps) .
The CLK control willallow you to switchbetween media displaymode (radio station,stereo information,etc.) and clock displaymode (time). When inclock mo
fuel pump shut-offswitch ... 157gauge ... 16improving fueleconomy ... 217low fuel warninglight ...
lighting up panel andinterior ... 66JJack ... 163positioning ... 163storage ... 163
lubricantspecifications ... 241reverse ... 150Mirrorsside view mirrors(power) ... 79Motorcraftparts ...
Safety seats forchildren ... 122Seat belts (see Safetyrestraints) ... 101Seats ... 98child safety
WWarning chimes ... 14–15Warning lights (seeLights) ... 10Washer fluid ... 197Water, Drivingthrough ...
256
playing. If returning from radio or tape mode, CDplay will begin where it stopped last.Press the CD control to toggle between single CDand CD changer
DolbyT noise reductionDolbyt noise reductionoperates in tape mode.Dolbyt noise reductionreduces the amount ofhiss and static during tape playback.Pres
Mute modePress the MUTEcontrol to mute theplaying media. Pressthe MUTE controlagain to return to theplaying media.MACHT MP3 MUSIC SYSTEM1. ON/OFF and
Volume/power controlPress the control toturn the audio systemon or off.Turn the control toraise or lower thevolume.If the volume is set above a certai
The following warning may be required by Californialaw:CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of itsconstituents, and certain
Speaker fade adjustSpeaker sound can beadjusted between thefront and rearspeakers.Speaker balance adjustSpeaker sounddistribution can beadjusted betwe
numbers each MP3 track on the disc (denoted bythe .mp3 file extension) from T001 to T255.• MP3 directory mode represents a directorystructure consisti
Press and hold the SEEK control to quickly seekthrough all tracks in MP3 flat file mode or all tracksin the current MP3 directory.Note: If a track has
scan function is enabled. When the end of the disc isreached, the player will continue to scan from thefirst track forward.Press SCN again to disengag
Setting memory preset stations1. Select the frequencyband with the AM/FMselect control.2. Select a station. Refer to Tune adjust or Seekfunction for m
To set the minutes, press and hold the CLK controlwhile performing the following functions:• Presson theTUNE DIR control todecrease theminutes.• Press
Playing an MP3 disc in MP3 flat file mode andMP3 directory mode• Insert an MP3 disc into the player. CD and LOADwill appear in the display. Initializa
• Press on TUNE DIR to revert to the previousdirectory on the MP3 disc. If the current directoryis the first directory on the disc, pressingwillselect
Shuffle featureThe shuffle feature works in CD mode, MP3 flat filemode and MP3 directory mode.Shuffle feature in CD modeThe shuffle feature plays all
• To select anotherrandom track on thedisc, pressor on the SEEKcontrol.• Press SCN to scanthrough randomtracks. The tracknumber will flash inthe displ
This Owner’s Guide describes every option andmodel variant available and therefore some of theitems covered may not apply to your particularvehicle. F
To shuffle tracks inanother directory,pressor on theTUNE DIR control to select the desired directory.The shuffle function still remains enabled.Press
• Rotate the volumecontrol to advanceor reverse throughthe tracks.The MP3 icon will blink in the display while theMACHt track function is enabled.When
Saving and naming MP3 files• Your MACHt MP3 music system supports discscontaining up to 255 files in 255 directories. Discscontaining more than 255 fi
MACHT 1000 SOUND SYSTEM RADIO(CD CHANGER COMPATIBLE)MACH 1000T AUDIO SYSTEMYour vehicle may be equipped with the MACH1000t audio system. This system i
at a “nominal” listening level when the ignitionswitch is turned back on.Speed sensitive volumeWith this feature, radio volume changesautomatically an
Treble adjustThe treble adjustcontrol allows you toincrease or decreasethe audio system’streble output.Press the TREB control. Use the SEL control toi
Seek function in radio mode• Press to find thenext listenablestation down thefrequency band. SEEK DOWN will display.• Pressto find the next listenable
AM/FM selectThe AM/FM selectcontrol works in radioand CD modes.AM/FM select in radio modeThis control allows you to select AM or FMfrequency bands. Pr
preset stations. This feature is helpful on trips whenyou travel between cities with different radiostations.Starting autostore1. Press and momentaril
Tune adjust in radio mode• Press to move tothe next frequencydown the band(whether or not a listenable station is locatedthere). Hold the control to m
Warning symbols on your vehicleWhen you see thissymbol, it is imperativethat you consult therelevant section of thisguide before touching or attemptin
If your vehicle is equipped with a CD changer,pressing the CD control again will allow you totoggle between accessing the multi disc system andthe CD
This six disc CD player is equipped with a CDdoor. Compact discs should only be insertedinto the player after the door has been openedby the player. D
If a CD is ejected and not removed from the door ofthe CD player, the player will automatically reloadthe CD. This feature may be used when the igniti
On Premium audios,press the COMPcontrol until COMP ONis displayed.Menu modeThe MENU controlallows you to accessmany different featureswithin your audi
FIND type — Allows you to select your desired FMprogram type and search for that selection.SHOW — Allows you to select from NAME (displaysthe name of
To disengage the feature, press the MENU controluntil TRAFFIC ON displays. Press the SEL control.The display will read TRAFFIC OFF.Traffic announcemen
Digital signal processingThe digital signal processing (DSP) feature allowsyou to change the signal mode to suit your listeningtastes.Press the DSP co
MACH 1000 mode raises the bass response of thetrunk mounted subwoofers.Mute modePress the control tomute the playingmedia. Press thecontrol again to r
• The player’s internal temperature is above 60°C(140°F). Allow the player to cool down beforeoperating.• A disc with format and dimensions not within
cleaner and wipe from the center out to the edge.Do not use circular motion.CD, MP3 AND CD PLAYER CARE• Handle discs by their edges only. Never touch
SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includesBumper-to-Bumper Coverage, Safety RestraintCoverage, Corrosion Coverage, and
CLEANING CASSETTE PLAYER (IF EQUIPPED)Clean the tape player head with a cassette cleaningcartridge after 10 to 12 hours of play in order tomaintain th
RADIO RECEPTION FACTORSThree factors can affect radio reception:• Distance/strength. The further an FM signaltravels, the weaker it is. The listenable
MANUAL HEATING AND AIR CONDITIONINGSYSTEMFan speed controlControls the volume ofair circulated in thevehicle.Temperature control knobControls thetempe
• O (Off) – Outside air is shut out and the fan willnot operate. This mode may reduce undesirableodors from entering the vehicle but may increasethe p
• Under normal weather conditions, do not leaveyour vehicle in the Max A/C (if equipped),recirculation mode (if equipped) or Off modewhen turning off
HEADLAMP CONTROL• Pull the headlampcontrol toward youto the first positionto turn on theparking lamps, taillamps, license platelamps and markerlamps.•
Always remember to turn on yourheadlamps at dusk or during inclementweather. The Daytime Running Light (DRL)System does not activate your tail lamps a
AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimedat the assembly plant.If your vehicle has been in an accident the alignmentof your
4. On the wall orscreen you will observea light pattern with flatedges at the top of thebeam pattern. If theflat edges are not atthe horizontal refere
BULBSReplacing exterior bulbsCheck the operation of the following lampsfrequently:• Headlamps• Tail lamps• Brakelamps• High-mount brakelamp• Turn sign
Notice to owners of Cobra vehiclesBefore you drive your vehicle, be sure to read the“SVT Cobra Owner’s Guide Supplement.” This bookcontains important
Function Trade NumberVisor vanity lamp 74Glove compartment 194Rearview mirror map lamps 192Fog lamp 899All replacement bulbs are clear in color except
4. Disconnect theelectrical connectorfrom the bulb bypulling rearward.5. Remove the bulbretaining ring byrotating itcounterclockwise(when viewed from
4. Install the headlamp on vehicle by aligning thelamp with the rear snap retainers, push to seat andsecure with two retainer pins.5. Turn the headlam
Replacing high-mount brakelamp bulbs1. Open trunk.2. Inside trunk, locateaccess hole under therear decklid.3. Remove the bulbsocket by rotating it 45d
Replacing license plate lamp bulbs1. Open trunk andremove bulb socketfrom the trunk lid byturningcounterclockwise.2. Pull the bulb straightout of the
WINDSHIELD WIPER/WASHER CONTROLSRotate the windshieldwiper control to thedesired interval, low orhigh speed position.The bars of varyinglength are for
Changing the wiper bladesTo replace the wiper blades:1. Pull the wiper armaway from thewindshield and lockinto the serviceposition.2. Turn the blade a
OVERHEAD STORAGE NET (IF EQUIPPED)Be sure tosecure objectswhen placed in thestorage net in orderto help reduce therisk that they becomeprojectiles in
• Press the top portionof the rocker switchto close.• Press the bottomportion of the rockerswitch to open.Express downTo make the driverwindow open fu
POWER SIDE VIEW MIRRORS(IF EQUIPPED)To adjust your mirrors:1. Move the mirrorselector control all theway to the left toadjust the left mirroror all th
These are some of the symbols you may see on yourvehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-S
To turn speed control off• Press OFF or• Turn off the vehicleignition.Once speed control isswitched off, thepreviously programmedset speed will beeras
To set a higher set speed• Press and hold SETACCEL. Release thecontrol when thedesired vehiclespeed is reached or• Press and releaseSET ACCEL tooperat
To disengage speed control• Depress the brakepedal or• Depress the clutchpedal (if equipped).Disengaging the speedcontrol will not erasethe previously
OVERDRIVE CONTROL (IF EQUIPPED)Activating overdrive(Overdrive) is the normal drive position for thebest fuel economy.The overdrive function allows aut
CENTER CONSOLEYour vehicle may be equipped with a variety ofconsole features. These include:• Dual cupholders• Auxiliary power point• Coin holder slot
Lowering the convertible topThe convertible top can be lowered with the sidewindows either up or down.The convertible top will not operate unless thep
Installation of the boot1. Push boot rearwardand engage boot underthe body molding atthe rear and sides.2. Fasten snap on bootto quarter trim panelon
Raising the convertible topThe convertible top will not operate unless theparking brake is engaged. Do not raise the top whilethe vehicle is moving be
KEYSThe key operates all locks on your vehicle. In case ofloss, replacement keys are available from yourdealer.You should always carry a second key wi
To open the luggagecompartment door (lid)from the inside, pull theilluminated “T” shapedhandle and push up onthe trunk lid. Thematerial that the handl
Vehicle Symbol GlossaryInterior LuggageCompartmentRelease SymbolPanic AlarmEngine Oil Engine CoolantEngine CoolantTemperatureDo Not Open WhenHotBatter
REMOTE ENTRY SYSTEMThis device complies with part 15 of the FCC rulesand with RS-210 of Industry Canada. Operation issubject to the following two cond
Locking the doorsPress this control tolock all doors.To confirm all doorsare closed and locked,press the control asecond time withinthree seconds. The
Replacing the batteriesThe transmitter is powered by two coin typethree-volt lithium batteries. Typical operating rangewill allow you to be up to 10 m
To reprogram the transmitters yourself, place thekey in the ignition and turn from LOCK to OFF andcycle between OFF and ON eight times in rapidsuccess
systems. Use of these systems may result in vehiclestarting problems and a loss of security protection.THEFT INDICATORThe theft indicator is located o
Key informationYour vehicle is supplied with two coded keys. Onlya coded key will start your vehicle. Spare codedkeys can be purchased from your deale
Programming spare keysA maximum of eight keys can be coded to yourvehicle. Only SecuriLocky keys can be used. Toprogram a coded key yourself, you will
If successful, the new coded key(s) will start thevehicle’s engine and the theft indicator willilluminate for three seconds and then go out.If not suc
SEATINGAdjustable head restraints (if equipped)Your vehicle’s seats may be equipped with headrestraints which are vertically adjustable. Thepurpose of
Lift handle to moveseat forward orbackward.Pull lever up to adjustseatback.Using the power lumbar support (if equipped)The power lumbarcontrol is loca
Commentaires sur ces manuels