Before drivingIntroduction 2Instrumentation 6Controls and features 17Seating and safety restraints 84Starting and drivingStarting 122Driving 127Roadsi
Service engine soonYour vehicle is equipped with acomputer that monitors the engine’semission control system. Thissystem is commonly known as theOn Bo
the label. Also, use the safety belt extension only if the safety belt is tooshort for you when fully extended. Do not use extensions to change thefit
If... Then...The driver’s safety belt is notbuckled before the vehicle hasreached at least 5 km/h (3 mph)and 1-2 minutes have elapsedsince the ignitio
Reasons given... Consider...“Traffic is light” Nearly 1 of 2 deaths occur in single-vehiclecrashes, many when no other vehicles are around.“Belts wrin
• the ignition switch is in the OFF position• all vehicle doors are closed• the driver’s safety belt is unbuckled• the parklamps/headlamps are in OFF
Safety belt maintenanceInspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to ma
severity. This information will assist Ford in the servicing of your vehicleand may help Ford better understand real world collisions and furtherimpro
Important supplemental restraint system precautionsAir bags DO NOT inflate slowly orgently and the risk of injury from adeploying air bag is greatest
Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause thoseobjects to be propelled by the
Determining if the system is operationalThe supplemental restraint system uses a warning indicator in theinstrument cluster or a back-up tone to indic
How do the air bag supplemental restraints work?The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to noti
Light is blinking:Engine misfire is occurring which could damage your catalytic converter.You should drive in a moderate fashion (avoid heavy accelera
Side air bag system (if equipped)Do not place objects or mount equipment on or near the air bagcover on the side of the seatbacks of the front seats o
How does the side air bag system work?The side air bag system consists ofthe following:• An inflatable nylon bag (air bag)with a gas generator conceal
Several air bag systemcomponents get hot afterinflation. Do not touch them afterinflation.If the side air bag hasdeployed, the air bag willnot functio
Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.Alwa
SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully fo
• Put the safety belt in the automatic locking mode. Refer to Automaticlocking mode.Ford recommends the use of a child safety seat having a top tether
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a c
Installing child safety seats in the lap belt seating positions1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that itsbottom is pe
1. Position the child safety seat on the seat cushion.2. Route the child safety seat tether strap over the back of the seat.For vehicles with adjustab
Anti-lock brake system (ABS) (If equipped)Momentarily illuminates when theignition is turned to the ON positionto ensure the circuit is functional. If
Attaching child safety seats with LATCH attachments for child seatanchorsSome child safety seats are labeled as LATCH or LATCH-compatible childseats.
Attach the lower anchors for child seat installation or loweranchors for child seat installation-compatible child seat only tothe appropriate location
PREPARING TO START YOUR VEHICLEEngine starting is controlled by the powertrain control system. Thissystem meets all Canadian Interference-Causing Equi
3. Make sure the gearshift is in P(Park).4. Make sure the parking brake isset.5. Turn the key to 4 (ON) withoutturning the key to 5 (START).If there i
• If the driver’s safety belt is fastened, the light may not illuminate.STARTING THE ENGINENOTE: Whenever you start your vehicle, release the key as s
Cold starting performance can also be improved with the use of anengine block heater. The engine block heater is available as a Fordoption and can als
Guarding against exhaust fumesAlthough odorless and colorless, carbon monoxide is present in exhaustfumes. Take precautions to avoid its dangerous eff
BRAKESYour service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance.Occasional brake noise is normal and o
ABS warning lampABSTheABSwarning lamp in the instrument cluster momentarily illuminateswhen the ignition is turned to the ON position. If the light do
Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th
Engine oil pressureMomentarily illuminates when theignition is turned to the ON positionand the engine is off. Illuminateswhen the oil pressure falls
Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.TRACTION
During Traction Controly operation,the traction control active light willilluminate, you may hear an electricmotor type of sound coming fromthe engine
• high crown in center of road• high crosswinds• wheels out of alignment• loose or worn suspension componentsAUTOMATIC TRANSAXLE OPERATIONBrake-shift
Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn off the ignition whenever you leaveyour vehicle.If the park
Hold the brake pedal down while you move the gearshift leverfrom P (Park) to another position. If you do not hold the brakepedal down, your vehicle ma
N (Neutral)With the gearshift lever in the N(Neutral) position, the vehicle canbe started and is free to roll. Holdthe brake pedal down while in thisp
When to use D (Drive)The D (Drive) position eliminatesthe needless shifting back and forthbetween third and fourth gears thatyour vehicle may do when
When parking, do not use the gearshift in place of the parkingbrake. Always set the parking brake fully and make sure that thegearshift is securely la
• Maximum Trailer Weight: Maximum weight of a trailer the loadedvehicle (including occupants and cargo) is permitted to tow. It isdetermined by subtra
Once through the water, always try the brakes. Wet brakes do not stopthe vehicle as effectively as dry brakes. Drying can be improved bymoving your ve
Key-in-ignition warning chimeSounds when the key is left in the ignition in the OFF/LOCK or ACCposition and the driver’s door is opened.Headlamps on w
3.0L 4-Valve Duratec EngineModel PassengerLoad - #/kg (lbs.)LuggageLoad - kg (lbs.)Max TrailerWt.- kg (lbs.)Sedan 5/340 (750) 0 590 (1 300)2/135 (300)
Trailer brakesElectric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspeci
• If you are driving down a long or steep hill, shift to a lower gear. Donot apply the brakes continuously, as they may overheat and becomeless effect
LUGGAGE RACK (IF EQUIPPED)The rear cross-bar can be adjusted to fit the item being carried. Thefront cross-bar does not move. Do not load more than 44
Getting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program
Roadside coverage beyond basic warrantyIn the United States, you may purchase additional roadside assistancecoverage beyond this period through the Fo
If your vehicle is a sedan, the fuelpump shut-off switch is located onthe right side of the trunk behindthe trunk liner.If your vehicle is a wagon, th
FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth
Passenger compartment fuse panelThe fuse panel is located below and to the left of the steering wheel bythe brake pedal. Remove the panel cover to acc
Fuse/RelayLocationFuse AmpRatingPassenger Compartment Fuse PanelDescription12 10A Heated Mirrors, Rear Defrost Switch13 20A Power Point14 — Not Used15
TachometerIndicates the engine speed inrevolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the e
Fuse/RelayLocationFuse AmpRatingPassenger Compartment Fuse PanelDescription35 — Not Used36 15A Turn Signals, Back-up Lamps37 15A Transmission Position
The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description1 60A** Fuse Junction Panel2 30A** PCM R
Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description21 15 A* Left Headlamp22 10A* A/C Clutch Relay, PCM Keep Alive Power23 — Starter Mot
When driving with the temporary spare tire do not:• exceed 80 km/h (50 mph) under any circumstances• load the vehicle beyond maximum vehicle load rati
• In the sedan, these are located inthe trunk cargo area storagecompartment.• In the wagon, they are stored inthe left side rear trim panel forthe tem
5. Loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground.6. Put the jack in the jack n
11. Return the flat tire, jack and lugwrench to their proper storagelocations. Make sure the jack isfastened so it does not rattle whenyou drive.12. U
3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake onboth vehicles
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable. Make th
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
OdometerRegisters the total kilometers(miles) of the vehicle.Trip odometerRegisters the kilometers (miles) ofindividual journeys. To reset,depress the
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center.It
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
Note: Do not start your engine with the air cleaner removed and do notremove it while the engine is running.OPENING THE HOOD1. Inside the vehicle, pul
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.0L V6 Vulcan engine1. Automatic transmission fluid dipstick2. Brake fluid reservoir3. Air filter ass
3.0L DOHC V6 Duratec engine1. Automatic transmission fluid dipstick2. Brake fluid reservoir3. Air filter assembly4. Battery5. Engine oil filler cap6.
ENGINE OILChecking the engine oilRefer to the scheduled maintenance guide for the appropriate intervalsfor checking the engine oil.1. Make sure the ve
• If the oil level is below the add1QT or MIN mark, add enough oilto raise the level within the1QT-FULL or the MIN-MAX range(depending on application)
Engine oil and filter recommendationsLook for this certificationtrademark.SAE 5W-20 engine oil is recommended.Only use oils “Certified For Gasoline En
BRAKE FLUIDChecking and adding brake fluidBrake fluid should be checked andrefilled as needed. Refer to thescheduled maintenance guide forthe service
HEADLAMP CONTROLRotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlam
WINDSHIELD WASHER FLUIDWasher fluidCheck the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with asymbol.If the level is low, add
Checking and adding washer fluid for the liftgate (if equipped)The opening for the reservoir islocated on the passenger side underthe tail lamp. Refil
• Protection against rust and other forms of corrosion.• Enables calibrated gauges to work properly.When the engine is cold, check thelevel of the eng
Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservo
•Do not use alcohol, methanol or brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcohol andother liquids can cause e
Whenever coolant has been added, the coolant level in the coolantreservoir should be checked the next few times you drive the vehicle. Ifnecessary, ad
• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequatefreeze protection at the tempera
1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gauge indicator will benear the center
TRANSMISSION FLUIDChecking automatic transmission fluidRefer to your scheduled maintenance guide for scheduled intervals forfluid checks and changes.
Correct fluid levelThe transmission fluid should be checked at normal operatingtemperatures 66°C-77°C (150°F-170°F) on a level surface. The normaloper
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel during headlampand parklamp operation.• Rotate up to brighten.• Rotate down to
CABIN AIR FILTER (IF EQUIPPED)The particulate air filtration system is designed to reduce theconcentration of airborne particles such as dust, spores
1. Release and open the hood.2. Remove the four clips located on the cowl vent screen.Maintenance and care181
3. Remove the cowl vent screen.4. Remove the two screws retaining the cowl top inner panel shield.5. Remove the inner panel shield.Maintenance and car
6. Remove the filter from the cabin air filter housing.7. Install the new cabin air filter into the cabin air filter housing.Maintenance and care183
8. Replace the inner panel shield.9. Replace the two screws retaining the cowl top inner panel shield.10. Replace the cowl vent screen.Maintenance and
11. Replace the four clips located on the cowl vent screen.BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally doe
If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced.For longer, trouble-free operation, keep
2. Put the gearshift in P (Park), turn off all accessories and start theengine.3. Run the engine until it reaches normal operating temperature.4. Allo
Changing the wiper bladesTo replace the wiper blades:1. Pull the wiper arm away from thewindshield and lock into the serviceposition.2. Turn the blade
U.S. Department of Transportation-Tire quality grades: The U.S.Department of Transportation requires Ford to give you the followinginformation about t
The defroster turns off automatically after 10 minutes or when theignition is turned to the OFF position. To manually turn off the defrosterbefore 10
The temperature grade for this tire is established for a tire thatis properly inflated and not overloaded. Excessive speed,underinflation, or excessiv
Replacing the tiresReplace the tires when the wearband is visible through the tiretreads.When replacing full size tires, never mix radial bias-belted,
Follow these guidelines when using snow tires and chains:• Use only cable type chains offered by Ford as an accessory orequivalent. SAE class “S” or o
Fuel ethanol and gasoline may contain benzene, which is acancer-causing agent.Observe the following guidelines when handling automotive fuel:• Extingu
• FFV fuel tanks may contain zero to 85 percent ethanol. Any fuelblends containing gasoline and ethanol should be treated the same as“Fuel Ethanol (E8
The flow of fuel through a fuel pump nozzle can produce staticelectricity, which can cause a fire if fuel is pumped into anungrounded fuel container.U
The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stopsbefore completely rem
FFV engine (if equipped)Your vehicle is designed to use Fuel Ethanol(E85), “Regular” unleadedgasoline or any percentage of the two fuels combined.U.S.
your VIN or the label on the inside of your fuel filler door. Whenchecking the VIN, look for the engine type identifier (8th character). Ifyour vehicl
ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform
The following warning may be required by California law:CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain
Mode selector controlControls the direction of the airflowto the inside of the vehicle.The air conditioning compressor canoperate in all modes except.
Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in kilometers or miles).2. Each time you fill the tan
• Using the air conditioner or defroster may reduce fuel economy.• You may want to turn off the speed control in hilly terrain ifunnecessary shifting
EPA window stickerEvery new vehicle should have the EPA window sticker. Contact yourdealer if the window sticker is not supplied with your vehicle. Th
Exhaust leaks may result in entry of harmful and potentiallylethal fumes into the passenger compartment.Do not make any unauthorized changes to your v
• Tail lamps• Brakelamps• High-mount brakelamp• Turn signals• Backup lamps• License plate lampDo not remove lamp bulbs unless they will be replaced im
4. Remove the protective dust shieldfrom the housing by turning thedust shield counterclockwise (whenviewed from the rear).5. Disconnect the electrica
To install the new bulb:Handle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and donot to
Replacing front parking lamp/turn signal/cornering lamp bulbs1. Make sure the headlamp controlis in the OFF position.2. Remove the bolt from theheadla
Replacing high-mount brakelamp bulbs — Sedan only• TYPE A1. Open trunk and locate theinsulator under the rear window.Note the number of the push pinsb
Replacing high-mount brakelamp bulbs — Wagon only1. Open liftgate.2. Remove two screw covers, screwsand handle from liftgate.3. Remove two screws and
• (Floor and defrost)-Distributes outside air through the windshielddefroster ducts and the floor ducts. Heating and air conditioningcapabilities are
7. Carefully lift the lamp assemblyaway from the liftgate.8. Remove the bulb socket byrotating it counterclockwise andpulling it out from the lampasse
Sedan1. Remove two screws, grommetsand the license plate lamp assemblyfrom the trunk lid.2. Carefully pull the bulb from thesocket and push in the new
4. Remove the bulb socket byrotating it counterclockwise, thenpulling it out of the lamp assembly.5. Pull the bulb from the socket andpush in the new
Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an
AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident the alignment of yo
4. On the wall or screen you willobserve an area of high intensitylight. The top of the high intensityarea should touch the horizontalreference line,
CLEANING AND CARING FOR YOUR VEHICLERefer to the Customer Assistance chapter for a list of Ford-approvedcleaners, polishes and waxes.Washing your vehi
Use only carnauba or synthetic-based waxes. Use a cleaning fluid with aclean cloth to remove any bugs before waxing your vehicle. Use tarremover to re
Cleaning the exterior lampsWash with the same detergent as the exterior of your vehicle. Ifnecessary, use a tar remover such as Ford Extra Strength Ta
• 3.0L Vulcan engine• 3.0L Duratec engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.Ma
• Don’t put objects under the front seat that will interfere with theairflow to the back seats.• Remove any snow, ice or leavesfrom the air intake are
Cleaning the instrument panelClean with a damp cloth, then dry with a dry cloth.Avoid cleaner or polish that increases the gloss of the upper portion
Cleaning and maintaining the safety beltsClean the safety belts with a mild soap solution recommended forcleaning upholstery or carpets. Do not bleach
MOTORCRAFT PART NUMBERSComponent 3.0L V6 Vulcanengine3.0L FFV V6engine3.0L DOHC V6Duratec engineAir filterelement1FA-1683 FA-1683 FA-1683Fuel filter F
REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid MotorcraftHighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to line onreservoir
Fluid Ford PartNameApplication CapacityWindshieldwasher fluid -FrontUltra-ClearWindshieldWasherConcentrateAll 2.8L (94.7 oz.)Windshieldwasher fluid -R
ItemsFord PartName orequivalentFord PartNumberFordSpecificationConstant velocityjointsCV Joint Grease(High Temp.)E43Z-19590-A ESP-M1C207-AEngine coola
ENGINE DATAEngine 3.0L V6 Vulcanengine3.0L FFV V6engine3.0L DOHC V6Duratec engineCubic inches 182 182 183Required fuel 87 octane 87 octane orEthanol (
52341Capacities and specifications227
IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt
Vehicle identification numberThe vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Please not
Turning the EATC onPress AUTO, any of the override controls or the fan speed control. TheEATC will only operate when the vehicle is running.Turning th
Ford Extended Service PlanYou can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. For
taken to another dealer. If a particular dealership can not assist you,then contact the Customer Relationship Center.If you have questions or concerns
In the United States:Ford Motor CompanyCustomer Relationship Center16800 Executive Plaza DriveP.O. Box 6248Dearborn, Michigan 481211-800-521-4140(TDD
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes• avail
Board membershipThe Board consists of:• three consumer representatives• a Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa
You will receive a letter of explanation if your application does notqualify for Board review.Oral presentationsIf you would like to make an oral pres
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADAONLY)In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a
If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest F
Ford Multi-Purpose Cleaner*Motorcraft Car Wash ConcentrateMotorcraft Carlite Glass CleanerFord Spot and Stain Remover*Ford Super Premium Tire and Trim
Comfort and convenienceAir filtrationCargo netsCargo organizersCargo shades (wagon)Engine block heatersTravel equipmentElectrochromic inside mirror wi
Temperature selectionThe display window indicates theselected temperature, function(AUTO or one of the overridecontrols) and manual control of fanspee
• The Federal Communications Commission (FCC) and Canadian RadioTelecommunications Commission (CRTC) regulate the use of mobilecommunications systems
IN CALIFORNIA (U.S. ONLY)California Civil Code Section 1793.2(d) requires that, if a manufactureror its representative is unable to repair a motor veh
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould im
AAccessory delay ...63Air bag supplemental restraintsystem ...104, 106, 110and child safety seats ...
Child safety seats ...114attaching with tether straps ..118in front seat ...115in rear seat ...
idle speed control ...185lubricationspecifications ...224, 226refill capacities ...223service poin
high beam ...8, 17replacing bulbs ...204turning on and off ...17warning chime ...
Locksautolock ...78childproof ...63Lubricant specifications ...224, 226Lumbar support
Servicing your vehicle ...162Spark plugs,specifications ...222, 226Specification chart,lubricants ...
249
Temperature conversionPress MAX A/C and F at the same time (until the display changes)to switch between Fahrenheit and Celsius.Fan speed ( )When AUTO
250
251
252
253
254
Item InformationRequired fuel Refer to 9Octanerecommendations9 in theMaintenance and care chapter.Fuel tank capacity 68.1L (18 gallons)Engine oil capa
1Use either green-colored Motorcraft Premium Engine Coolant oryellow-colored Motorcraft Premium Gold Engine Coolant. DO NOT USEFord Extended Life Engi
Manual override controlsThe override controls are located at the bottom of the EATC and allowyou to determine where airflow is directed. To return to
• (Floor)-Allows for maximum heating by distributing outside airthrough the floor ducts. However, the air cannot be cooled below theoutside temperatur
Operating tips• In humid weather conditions, place the climate control system inFbefore driving. This will reduce fogging on your windshield.Once the
• Do not place objects over the defroster outlets. These objects canblock airflow and reduce your ability to see through your windshield.Avoid placing
WARNINGSWarnings provide information which may reduce the risk of personalinjury and prevent possible damage to others, your vehicle and itsequipment.
USING YOUR AUDIO SYSTEMAM/FM StereoVolume/power controlPress the control to turn the audiosystem on or off.Turn control to raise or lowervolume.Contro
If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition
Seek function in radio mode• Press to find the next listenable station down the frequency band.• Pressto find the next listenable station up the frequ
• The treble adjust control allowsyou to increase or decrease theaudio system’s treble output.Speaker balance/fade adjust• Speaker sound distribution
MACHT Audio System with AM/FM Stereo/CassetteVolume/power controlPress the control to turn the audiosystem on or off.Turn control to raise or lowervol
AM/FM selectThe AM/FM select control works inradio, tape and CD modes (ifequipped). Press the AM or FMcontrol to enter into radio mode.AM/FM select in
• Press to select the next disc in the CD changer. Hold the controlto fast-forward through the remaining discs.Seek functionThe seek function control
Scan function in CD modePress the SCAN control to hear a short sampling of all selections on theCD. (The CD scans in a forward direction, wrapping bac
• Speaker sound can be adjustedbetween the front and rearspeakers.Inserting a tapePush only slightly when inserting acassette tape (with the open edge
Fast forwardThe fast forward control works intape and CD modes.• In the tape mode, tape directionwill automatically reverse when the end of the tape i
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-
Shuffle featureThe shuffle feature operates in CDmode and plays all tracks on thecurrent disc in random order.If equipped with the CD changer, the shu
Audio System with AM/FM Stereo/Single CD PlayerVolume/power controlPress the control to turn the audiosystem on or off.Turn control to raise or lowerv
AM/FM selectThe AM/FM select control works inradio, and CD modes (if equipped).Press the AM or FM control to enterinto radio mode.AM/FM select in radi
Seek functionThe seek function control works inradio or CD mode.Seek function in radio mode• Press to find the next listenable station down the freque
Setting memory preset stations1. Select the frequency band withthe AM/FM select control.2. Select a station. Refer to Tuneadjust or Seek function for
CD select• Pressing the CD control when theignition is on will engage thesystem if a CD is present in theaudio system.• To begin CD play, press the CD
Compression adjustCompression adjust brings soft andloud CD passages together for amore consistent listening level.Press the COMP control to activate
CD changer (if equipped)Your CD changer is either located in the trunk, the console or the rightside cargo area storage compartment.1. Slide the door
If you pull too hard on the disc holder, the disc holder may comecompletely out of the magazine. If this happens, reinsert the disc holderback into th
The CD magazine may be inserted or ejected with the radio power off.ONLY use the magazine supplied with the CD changer, other types willdamage the uni
Vehicle Symbol GlossaryChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Engine OilEngine CoolantEngine CoolantTemperat
• Do not insert more than one disc into each slot of the CD changermagazine.Do not insert any promotional (odd shaped or sized) discs, ordiscs with re
• Terrain.Hills, mountains and tall buildings between your vehicle’santenna and the radio station signal can cause FM reception problems.Static can be
TRACTION CONTROLY (IF EQUIPPED)This control can be used to turn theTraction Controly on or off. Referto the Traction Controlysection ofthe Driving cha
SPEED CONTROL (IF EQUIPPED)To turn speed control on• Press ON.Vehicle speed cannot be controlleduntil the vehicle is traveling at orabove 48 km/h (30
To set a speed• Press SET+. For speed control tooperate, the speed control mustbe ON and the vehicle speedmust be greater than 48 km/h(30 mph).If you
To set a lower set speed• Press and hold CST −. Releasethe control when the desiredspeed is reached or• Press and release CST − tooperate the Tap-Down
Indicator lightThis light comes on when either theSET or RES controls are pressed. Itturns off when the speed controlOFF control is pressed, the brake
Rear window wiper and washer (wagon only)The rear wiper control is locatedunder the headlamp controls Pressthe wiper control to activate therear wiper
TILT STEERINGPull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredpo
With the control in the middle position, the dome lamp will illuminatewhenever a front door is opened. If either front door has been openedfrom the ou
Headlampcontrol(pg. 17)Instrument paneldimmer control(pg. 18)Instrument cluster(pg. 8)Driver air bag(pg. 104)Turn signal andwiper/washer control(pg. 5
ILLUMINATED VISOR MIRROR (IF EQUIPPED)To turn on the visor mirror lamps,lift the mirror cover. Adjust theamount of light by sliding thecontrol.MOON RO
You will need a Phone Adapter System (PAS) that is compatible withyour cell phone that you install into the center console. This systemincludes a Phon
To prevent damage to the antenna or your car, remove the cellular phoneantenna mast before using an automatic car wash.POWER WINDOWSPress and hold the
Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controlsexcept for the driver’s press
POWER SIDE VIEW MIRRORSTo adjust your mirrors:1. Selectto adjust the leftmirror orto adjust the rightmirror.2. Move the control in the directionyou wi
CENTER CONSOLEYour vehicle may be equipped with a variety of console features. Theseinclude:• Utility compartment• Bin mat (snap-in)• Cupholders (fron
TRUNK REMOTE CONTROLPress the remote trunk releasecontrol on the instrument panel tothe left of the steering wheel.LIFTGATE (WAGON ONLY)You can open a
CARGO AREA FEATURESStorage compartmentYour vehicle comes equipped with astorage compartment in the floor ofthe cargo area. An additionalcompartment is
To install the shade:1. Fasten the cover into themounting brackets (make sure thecover is right side up).2. Pull the end of the shade towardyou and ho
2. Wrap the vinyl around the rollertube twice. Tuck the edges of thevinyl inside the end cap with eachwrap.3. Fold the edges of the vinyltowards the c
Electronic sound system(pg. 30)Gearshift(pg. 132)Climate control system(pg. 19)Speed control*(pg. 53)Instrumentation7
Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment.The rem
Unlocking the liftgate/trunkPress the control to unlock theliftgate/trunk.Sounding a panic alarmPress this control to activate thealarm.To deactivate
Replacing lost transmittersIf a remote transmitter has been lostand you would like to remove itfrom the vehicle’s memory, or youwould like to purchase
Replacing the batteryThe remote transmitter is powered by one coin type three-volt lithiumbattery CR2032 or equivalent. Typical operating range will a
The system is ready to arm whenever the key is removed from theignition. Any of the following actions will prearm the alarm system:• Press the remote
If the doors/hood or liftgate (wagon) are not closed and you press theremote entry transmitter twice to confirm the doors are locked, the hornwill chi
Triggering the anti-theft systemThe armed system will be triggered if:• Any door, liftgate or hood is opened without using the door key or theremote e
2. Press the 1/2 control within fiveseconds of step 1.3. Enter your personal 5 digit code.Enter each digit within five secondsof the previous one.Do n
2. To unlock the passenger’s door(s)and liftgate (wagon), press the 3/4control within five seconds ofunlocking the driver’s door.3. To unlock the trun
The user should receive a horn chirp to indicate the system has beenaltered.Pressing the power door UNLOCK control button again will toggle theAutoloc
WARNING LIGHTS AND CHIMESTurn signalIlluminates when the left or rightturn signal or the hazard lights areturned on. If one or both of theindicators s
Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 3(OFF) position. TheTHEFTlight inthe instrument cluster will flash
Large metallic objects, electronicdevices on the key chain that can beused to purchase gasoline or similaritems, or a second key on the samekey ring a
Programming spare keysA maximum of eight keys can be coded to your vehicle. OnlySecuriLocky keys can be used. To program a coded key yourself, youwill
INTERIOR LUGGAGE COMPARTMENT RELEASEYour vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of esc
SEATINGAdjustable head restraintsYour vehicle’s seats are equipped with head restraints which arevertically adjustable. The purpose of these head rest
Adjusting the front manual seatNever adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the seatbacks to red
Adjusting the front power seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the sea
Using the manual lumbar support (if equipped)The lumbar control is located on thefront of the seat cushion.Turn to adjust lumbar support.REAR SEATS2nd
3rd seat (wagon only)The third seat faces the rear of the vehicle. For height and weight limits,see the label on the seat cushion. When the seat is do
SAFETY RESTRAINTSPersonal Safety SystemThe Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupant
Safety beltMomentarily illuminates when theignition is turned to the ON positionto remind you to fasten your safetybelts. For more information, refer
common, moderate-severity impacts. A higher energy level is providedfor the most severe impacts. Whether or not the air bag deploys at allcan also be
When are the front air bags and pretensioners deployed?Front air bags and pretensioners aredesigned to activate in frontal andnear-frontal collisions,
In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a seat belt.Each seating position in your vehicle has
The front and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front passenger and rear seatoutboard safety b
Vehicle sensitive modeThe vehicle sensitive mode is the normal retractor mode, allowing freeshoulder belt length adjustment to your movements and lock
• Grasp the shoulder portion andpull downward until the entirebelt is extracted.• Allow the belt to retract. As the belt retracts, you will hear a cli
Safety belt pretensionerYour vehicle is equipped with safety belt pretensioners at the driver andfront outboard passenger seating positions.The safety
Front safety belt height adjustmentYour vehicle has safety belt heightadjustments for the driver and frontpassenger. Adjust the height of theshoulder
Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ
To fasten the belt, pull the combination lap and shoulder belt from theretractor so that the shoulder belt portion of the safety belt crosses yourshou
Commentaires sur ces manuels