Ford 2001 Excursion v.2 Manuel d'utilisateur

Before drivingIntroduction 2Instrumentation 6Controls and features 17Seating and safety restraints 85Starting and drivingStarting 121Driving 125Roadsi

Transmission control indicator light (TCIL) (if equipped)Illuminates when the TransmissionControl Switch (TCS), refer toOverdrive control in the Contr

Safety belt replacement labelThe short plastic boot on the frontsafety belt at the passengeroutboard anchor location covers a“Replace Belt” label on t

Failure to follow these instructions will affect the performance ofthe safety belts and increase the risk of personal injury.Safety belt pretensioner

Position the shoulder belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safetybelt properly could

• 2nd row center seating position (if equipped)The lap belt will adjust automatically. To fasten, grasp the tongue, andwith a continuous motion, pull

Belt minderThe Belt Minder feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders to thedriv

Reasons given... Consider...“Seat belts don’twork”Safety belts, when used properly, reduce risk ofdeath to front seat occupants by 45% in cars,and by

• the ignition switch is in the OFF position• all vehicle doors are closed• the driver’s safety belt is unbuckled• the parklamps/headlamps are in OFF

Safety belt maintenanceInspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to ma

and may help Ford better understand real world collisions and furtherimprove the safety of future vehicles.Important supplemental restraint system (SR

Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause thoseobjects to be propelled by the

Turn signalIlluminates when the left or rightturn signal or the hazard lights areturned on. If one or both of theindicators stay on continuously orfla

Air bags can kill or injure a child in a child seat. NEVER place arear-facing child seat in front of an active air bag. If you mustuse a forward-facin

force, there is the risk of death or serious injuries such as fractures,facial and eye injuries or internal injuries, particularly to occupants whoare

• The readiness light will not illuminate immediately after ignition isturned on.• A series of five beeps will be heard. The tone pattern will repeatp

Children and safety beltsIf the child is the proper size, restrain the child in a safety seat.Children who are too large for child safety seats (as sp

SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully fo

• Put the safety belt in the automatic locking mode. Refer to Automaticlocking mode (passenger side front and outboard rear seatingpositions) (if equi

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a c

Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a

3. Locate the correct anchor for the selected seating position.• The anchors are located underthe seat frame.4. Clip the tether strap to theanchor as

Door ajarIlluminates when the ignition is inthe ON position and any door isopen. It may also momentarilyilluminate after the engine is startedand all

5. Refer to the Installing child safety seats in combination lap andshoulder belt seating positions section of this chapter for furtherinstructions to

PREPARING TO START YOUR VEHICLEEngine starting is controlled by the powertrain control system. Thissystem meets all Canadian Interference-Causing Equi

2. Make sure the headlamps and vehicle accessories are off.3. Make sure the parking brake isset.4. Make sure the gearshift is in P(Park).5. Turn the k

STARTING THE ENGINENOTE: Whenever you start your vehicle, release the key as soon as theengine starts. Excessive cranking could damage the starter.1.

To prevent electrical shock, do not use your heater withungrounded electrical systems or two-pronged (cheater)adapters.Guarding against exhaust fumesA

BRAKESYour service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance.Occasional brake noise is normal and o

The Anti-Lock system does not decrease the time necessary toapply the brakes or always reduce stopping distance. Alwaysleave enough room between your

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released.

PREPARING TO DRIVE YOUR VEHICLEUtility vehicles have a significantly higher rollover rate thanother types of vehicles.In a rollover crash, an unbelted

If you cannot move the gearshift lever out of P (Park) with ignition inthe ON position and the brake pedal depressed:1. Apply the parking brake, turn

Supplemental restraint system (SRS) warning chimeFor information on the SRS warning chime, refer to the Seating andsafety restraints chapter.Key-in-ig

P (Park)Always come to a complete stopbefore shifting into P (Park). Makesure the gearshift lever is securelylatched in P (Park). This positionlocks t

Drive – Not shown on the display. Activate by pressing the transmissioncontrol switch (TCS) on the end of the gearshift lever with the gearshiftin the

Shift strategy (4R100 automatic transmission)To account for customer driving habits and conditions, your 4R100automatic transmission electronically co

• uses hub locks that can be engaged and disengaged automatically byusing a rotary control located on the instrument panel.• automatic hub locks can b

4x4 HIGH (4WD High) – Power delivered to front and rear axles forincreased traction.4x4 LOW (4WD Low) – Power to front and rear axles at low speeds.Sh

4. Move the 4WD control to the 4x4LOW position.5. Hold the shift command until theLOW RANGE indicator lightilluminates.6. If the LOW RANGE indicator l

Drive cautiously to avoid vehicle damage from concealed objects such asrocks and stumps.You should either know the terrain or examine maps of the area

If the transmission, transfer case or front axle are submerged in water,their fluids should be checked and changed, if necessary.Water intrusion into

When driving on snow or ice with either braking system, allow morestopping distance and drive slower than usual. Consider using one of thelower gears.

• Trailer Weight Range: Specified weight range that the trailer mustfall within that ranges from zero to the maximum trailer weight rating.Remember to

SpeedometerIndicates the current vehicle speed.Engine coolant temperature gaugeIndicates the temperature of theengine coolant. At normal operatingtemp

Your vehicle has the capability to haul more cargo and people than mostpassenger cars. Depending upon the type and placement of the load,hauling cargo

TRAILER TOWINGYour vehicle may tow aConventional/Class IV trailerprovided the maximum trailerweight is less than or equal to themaximum trailer weight

Do not exceed the GVWR or the GAWR specified on thecertification label.Towing trailers beyond the maximum recommended gross trailerweight could result

Trailer brakesElectric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspeci

Servicing after towingIf you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your scheduled maint

Recreational towing (all wheels on the ground)An example of recreational towing would be towing your vehicle behinda Motorhome. Follow these guideline

To remove the cross-bar assembly from the roof rack side rails:1. Loosen the latch at both ends of the cross-bar (both cross-bars areadjustable).2. Sl

GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford offers acomplimentary roadside assistance program. This program

Roadside coverage beyond basic warrantyIn the United States, you may purchase additional roadside assistancecoverage beyond this period through the Fo

The fuel pump shut-off switch islocated in the passenger’s foot well,by the kick panel.Use the following procedure to reset the fuel pump shut-off swi

OdometerRegisters the total kilometers(miles) of the vehicle.Trip odometerRegisters the kilometers (miles) ofindividual journeys. To reset,depress the

NOTE: Always replace a fuse with one that has the specified amperagerating. Using a fuse with a higher amperage rating can cause severe wiredamage and

To remove the fuse panel cover,turn the panel fastenerscounterclockwise.To remove a fuse use the fuse pullertool provided on the fuse panelcover.FUSE1

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger CompartmentFuse Panel Description1 20A Radio, Secondary Fusing for Audio Opti

Fuse/RelayLocationFuse AmpRatingPassenger CompartmentFuse Panel Description20 15A Starter Motor Relay, GEM21 5A Radio Start Feed22 10A Blower Motor Re

Power distribution boxThe power distribution box, trailertow and electronic shift on the flyrelay blocks are located in theengine compartment near the

The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description1 20A* Rear Wiper2 — Not Used3 15A* Quar

Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description17 — Not Used18 — Not Used19 20A*(Gasolineonly)— (Dieselonly)Gasoline only-E40D/HEGO

Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description113 30A**(Gasolineonly)20A**(Diesel only)PCM Power114 — Not Used115 30A** Trailer To

CHANGING THE TIRESIf you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel

1. Park on a level surface, activatehazard flashers and set the parkingbrake.2. Turn engine OFF and block thediagonally opposite wheel (block notprovi

Battery voltage gaugeThis shows the battery voltage whenthe ignition is in the ON position. Ifthe pointer moves and stays outsidethe normal operating

6. Insert the hooked end of the jackhandle into the jack and use thehandle to slide the jack under thevehicle.7. Position the jack according to thefol

• Rear8. Turn the jack handle clockwiseuntil the wheel is completely off theground and high enough to installthe spare tire.To lessen the risk ofperso

12. Remove the jack and fullytighten the lug nuts in the ordershown.13. Stow the the flat tire, jack, jackhandle and lug wrench. Make surethe jack is

JUMP STARTING YOUR VEHICLEThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury

Connecting the jumper cables1. Connect the positive (+) booster cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex

2. Start the engine of the disabled vehicle.3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disc

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center.On

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a

HEADLAMP CONTROLRotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlam

Do not start your engine with the air cleaner removed and donot remove it while the engine is running.OPENING THE HOOD1. Inside the vehicle, pull the

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT5.4L V8/6.8L V10 gasoline enginesRefer to the 7.3 Liter Power Stroke Direct Injection Turbo DieselOwne

1. Make sure the vehicle is on level ground.2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan.3. Set the parking brak

Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t

Ford production and aftermarket (Motorcraft) oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedtha

If you use a brake fluid that is not DOT 3, you will causepermanent damage to your brakes.Do not let the reservoir for the master cylinder run dry. Th

WINDSHIELD WASHER FLUIDWasher fluidCheck the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with asymbol.If the level is low, add

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “cold fill level” or within the “c

Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant couldmake it difficult to see through

reservoir when the engine is cool. Add the proper mixture of coolant andwater to the “cold full” level. For all other vehicles, which have a coolantde

High beamsPush forward to activate.Pull toward you to deactivate.Flash to passPull toward you to activate andrelease to deactivate.Daytime running lam

system may have a leak. Operating an engine with a low level of coolantcan result in engine overheating and possible engine damage.Recycled engine coo

If you drive in extremely hot climates:• it is still necessary to maintain the coolant concentrationabove 40%.• NEVER decrease the coolant concentrati

• the air conditioning system will be disabled.Continued operation will increase the engine temperature and the enginewill completely shut down, causi

CHECKING AND ADDING POWER STEERING FLUIDCheck the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules. If a

TRANSMISSION FLUIDChecking automatic transmission fluid (if equipped)Refer to your scheduled maintenance guide for scheduled intervals forfluid checks

Correct fluid levelThe transmission fluid should be checked at normal operatingtemperature 66°C-77°C (150°F-170°F) on a level surface. The normalopera

If necessary, add fluid in 250 ml (1/2 pint) increments through the fillertube until the level is correct.If an overfill occurs, excess fluidshould be

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How

Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lightedsubstances to come near th

6. With your foot on the brake pedal and with the A/C on, put thevehicle in D (Drive) and allow the engine to idle for at least one minute.7. Drive th

PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel during headlampand parklamp operation.• Rotate up to brighten.• Rotate down to

Changing the air filter element (gasoline engines only)1. Loosen the clamp that securesthe air filter element in place.2. Carefully separate the two h

TRACTION-LOK AXLE (IF EQUIPPED)This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under

Changing the wiper bladesTo replace the wiper blades:1. Pull the wiper arm away from thewindshield and lock into the serviceposition.2. Turn the blade

U.S. Department of Transportation-Tire quality grades: The U.S.Department of Transportation requires Ford to give you the followinginformation about t

The temperature grade for this tire is established for a tire thatis properly inflated and not overloaded. Excessive speed,underinflation, or excessiv

• Five tire rotationReplacing the tiresReplace the tires when the wearband is visible through the tiretreads.When replacing full size tires, never mix

Do not replace your tires with “high performance” tires or largersize tires.Failure to follow these precautions may adversely affect thehandling of th

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsDo not overfill the fuel tank. The pressure in an overfilled tankmay cause leak

• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kindcan lead to eye and respiratory tract irritation. In severe cases,excessive or p

Choosing the right fuelUse only UNLEADED FUEL. The use of leaded fuel is prohibited by lawand could damage your vehicle.Do not use fuel containing met

The following warning may be required by California law:CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain

REVERSE SENSING SYSTEM (IF EQUIPPED)The reverse sensing system (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when the revers

Many of the world’s automakersissued the World-wide Fuel Charterthat recommends gasolinespecifications to provide improvedperformance and emission con

If the “Service Engine Soon/Check Engine” indicator comes on and stayson after you start the engine, the fuel filler cap may not be properlyinstalled.

Filling the tankThe advertised fuel capacity of the fuel tank on your vehicle is equal tothe rated refill capacity of the fuel tank as listed in the R

5. Follow one of the simple calculations in order to determine fueleconomy:Multiply liters used by 100, then divide by total kilometerstraveled.Divide

Maintenance• Keep tires properly inflated and use only recommended size.• Operating a vehicle with the wheels out of alignment will reduce fueleconomy

EMISSION CONTROL SYSTEMYour vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to co

Please consult your “Warranty Guide” for complete emission warrantyinformation.Readiness for Inspection/Maintenance (I/M) testingIn some localities, i

Replacing headlamp bulbs1. Make sure that the headlamp control is in the OFF position.2. Open the hood.3. Disconnect the electricalconnector from the

Replacing front parking/turn signal bulbs1. Make sure headlamp switch is in OFF position.2. Open the hood.3. Remove the two screws andcarefully diseng

Replacing foglamp bulbsThe halogen bulb contains gas under pressure. The bulb mayshatter if the glass envelope is scratched or if the bulb isdropped.

The reverse sensing system detectsobstacles within approximately 1.8meters (5.9 ft.) of the rear bumperwith a decreased coverage area atthe outer corn

2. Rotate bulb socketcounterclockwise about1⁄4turn andremove from lamp assembly.3. Carefully pull the bulb straightout of the socket and push in thene

Replacing license plate lamp bulbsThe license plate bulbs are locatedbehind the rear bumper. To changethe license plate lamp bulbs:1. Reach behind the

Function Number ofbulbsTrade numberHeadlamps 2 9007Park/turn lamp 2 3157 AKSidemarker lamp 2 194Foglamp 2 899Tail/stop lamp 2 3157 KBackup lamp 2 3156

Washing your vehicleWash your vehicle regularly withcold or lukewarm water. Never usestrong detergents or soap. If yourvehicle is particularly dirty,

Avoid getting wax on the windshield, or on any surfaces which appearcoarse or bumpy. If you have wax applied at a commercial car wash, it isrecommende

• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.Cleaning non-painted plastic exterior parts

when you rinse it with water. The windshield, rear window and wiperblades should be cleaned on a regular basis, and blades or rubberelements replaced

Cleaning leather seats (if equipped)To clean, simply use a soft cloth dampened with water and a mild soap.Wipe the leather again with a damp cloth to

MOTORCRAFT PART NUMBERSComponent* 5.4L V8 engine 6.8L V10 engineAir filter element FA-1634 FA-1634Fuel filter FG-986B FG-986BOil filter FL-820-S FL-82

FluidFord PartNameApplication CapacityEnginecoolant-DieselengineRefer to your 7.3L Diesel SupplementEngine oil(includes filterchange)-GasolineenginesM

AUXILIARY POWER POINTPower outlets are designed for accessory plugs only. Do not hangany type of accessory or accessory bracket from the plug.Improper

Service refill capacities are determined by filling the rear axle to thebottom of the filler hole with the specified lubricant.3Use Ford Premium Engin

LUBRICANT SPECIFICATIONSItemFord partname orequivalentFord partnumberFordspecificationFront axle Motorcraft SAE75W-90Premium 4x4Front AxleLubricantXY-

ItemFord partname orequivalentFord partnumberFordspecificationHinges, latches,striker plates,fuel filler doorhinge and seattracksMulti-PurposeGreaseDO

Some transmission fluids may be labeled as dual usage, such asMERCON威 and MERCON威 V. These dual usage fluids are not to be usedin an automatic transmi

41523Capacities and specifications224

IDENTIFYING YOUR VEHICLECERTIFICATION LABELThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification Label be affixedt

Ford Extended Service PlanYou can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. For

If you have questions or concerns, or are unsatisfied with the service youare receiving, follow these steps:1. Contact your Sales Representative or Se

If you own a Lincoln vehicle and are away from home when your vehicleneeds service, or if you need more help than the dealership couldprovide, after f

Warranty Act, or to the extent allowed by state law, before pursuingreplacement or repurchase remedies provided by certain state laws. Thisdispute han

• Located in the left side storagecompartment in the third rowseating position.• Located on the right trim panel inthe rear cargo area.CLIMATE CONTROL

Concerns are ineligible for review if the New Vehicle Limited Warrantyhas expired at receipt of your application and, in certain states eligibilityis

• a brief summary of the action taken by the dealer(s) and Ford MotorCompany• the names (if known) of all the people you contacted at thedealership(s)

You may also contact the North American Customer Relationship Centerat 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952or by writin

The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emission control system and may causeengine knock

Ford Deluxe Leather and Vinyl Cleaner (not available in Canada)Motorcraft Vinyl Cleaner (Canada only)Ford Extra Strength Tar and Road Oil Remover* (no

Comfort and convenienceCargo organizersCargo shadesCargo traysDash trimEngine block heatersBattery warmer/blanketCellar phone holderRear door storage

Protection and appearance equipmentAir bag anti-theft locksCarpeted cargo matDoor edge guardsTruck coversCargo liners, interiorCarpet floor matsCleane

theft alarms - that are equipped with radio transmitters. Any suchequipment installed in your vehicle should comply with FCC or CRTCregulations and sh

Obtaining a French owner’s guideFrench Owner’s Guides can be obtained from your dealer or by writing toFord Motor Company of Canada, Limited, Service

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould im

Mode selector controlControls the direction of the airflowto the inside of the vehicle.The air conditioning compressor can operate in all modes except

AAccessory delay ...63Air bag supplementalrestraint system ...107–108and child safety seats ...109descrip

engine compartment ...214exterior ...213–214exterior lamps ...215instrument cluster lens ...

lubricationspecifications ...221, 223refill capacities ...218service points ...171starting

location ...138HHazard flashers ...148Head restraints ...88Headlamps ..

low fuel ...8safety belt ...10service engine soon ...8speed contro

SSafety belts (see Safetyrestraints) ...13, 95–99, 101Safety defects, reporting ...239Safety restraints ...95–99, 101belt

Ventilating your vehicle ...124WWarning chimes ...12–13Warning lights (see Lights) ...8Washer fluid ...

Item InformationRequired fuel Unleaded fuel only - 87 octaneFuel tank capacity 166.6L (44.0 gallons)Engine oil-gasolineengines (includes filterchange)

fluid. However, these dual usage fluids may be used in transmissions thatrequire the MERCON威 V type fluid.MERCON威 and MERCON威 V type fluids are not in

• (Floor and defrost) -Distributes outside air through thewindshield defroster ducts and the floor ducts. Heating and airconditioning capabilities are

• Remove any snow, ice or leavesfrom the air intake area at thebase of the windshield.• If your vehicle has been parked with the windows closed during

Your auxiliary A/C controls arelocated in the overhead console.In order for the auxiliary A/C-heatercontrols to function, the driver’sauxiliary A/C-he

Turn the temperature control to thedesired temperature.If the front seat control panel is setto MAX A/C, only cool air will beprovided because no heat

USING YOUR AUDIO SYSTEMPremium AM/FM Stereo/Cassette/Single CDVolume/power controlPress the control to turn the audiosystem on or off.Audio power can

BREAKING-IN YOUR VEHICLEThere are no particular guidelines for breaking-in your vehicle. Duringthe first 1 600 km (1 000 miles) of driving, vary speed

If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition

• Press to select the next disc in the CD changer. Hold the controlto fast-forward through the remaining discs.Seek functionThe seek function control

Scan function in tape modePress the SCAN control to hear a short sampling of all selections on thetape. (The tape scans in a forward direction. At the

Starting autoset memory preset1. Select a frequency using the AM/FM select controls.2. Press the AUTO control.3. When the first six strong stationsare

Press the TREB control then press:•to decrease the treble outputand•to increase the treble output.Speaker balance adjustSpeaker sound distribution can

• To begin CD play (if CD(s) areloaded), press the CD control.The first track of the disc willbegin playing. If returning fromradio or tape mode, CD p

Press the EJ control to stop andeject a CD.Dolby姞 noise reductionDolby威 noise reduction operates intape mode. Dolby威 noise reductionreduces the amount

Setting the clockTo set the hour, press and hold theCLK control and press SEEK:•to decrease hours and•to increase hours.To set the minute, press and h

The CLK button will allow you toswitch between media display mode(radio station, stereo information,etc.) and clock display mode (time).When in clock

Premium AM/FM Stereo In Dash Six CD RadioVolume/power controlPress the control to turn the audiosystem on or off.Turn the control to raise or lowervol

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-

AM/FM selectThe AM/FM select control works inradio and CD modes.AM/FM select in radio modeThis control allows you to select AM or FM frequency bands.

Seek functionThe seek function works in radio or CD mode.Seek function in radio mode• Pressto find the nextlistenable station down thefrequency band.

Radio station memory presetThe radio is equipped with six station memory preset controls. Thesecontrols can be used to select up to six preset AM stat

To deactivate autoset and return to your audio system’s manually setmemory stations, press the AM/FM control again.CD selectCD mode may be entered byp

Press the LOAD control. (You can choose which slot will be loaded bypressing the desired preset number. If you do not choose a slot, thesystem will ch

RewindThe rewind control works in CDmodes.Press and hold the REW controluntil the desired selection isreached. If the beginning of the disc is reached

On Audiophile audios, press the MENU control until compression statusis displayed. Press the SEL control to enable the compression featurewhen COMP OF

Menu modeThe MENU control allows you toaccess many different featureswithin your audio system. There arethree sets of menus available depending upon w

Traffic announcementsThis feature allows you to heartraffic announcements. When in thismode, traffic announcements willinterrupt radio and CD play.Whe

• Press the SEL control to engage this feature (RDS ON).RDS features:Once the RDS feature is on, press the MENU control to scroll throughthe following

Vehicle Symbol GlossaryChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Engine OilEngine CoolantEngine CoolantTemperat

• R&B• Religious• Rock• Soft• Top 40ShowThis feature allows you to select thetype of RDS broadcast informationthe radio will regularly show in the

• JAZZ CLUB—jazz club with clearly reflected sounds• HALL—rectangular concert hall capacity of about 2 000• CHURCH—church with a high vault• STADIUM—o

To turn on the rear seat controls, press the memory preset controls 3and 5 at the same time. Thewill appear in the radio display.Pressing 3 and 5 at t

Media selectPush the MEDIA control to togglebetween AM, FM1, FM2, tape, CD,or CD changer (if equipped).Memory preset controlPush the MEM control succe

• Do not insert more than one disc into each slot of the CD changermagazine.Do not insert any promotional (odd shaped or sized) discs, ordiscs with re

• Terrain. Hills, mountains and tall buildings between your vehicle’santenna and the radio station signal can cause FM reception problems.Static can b

TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.SPEED CONTROLTo turn speed control on• Press

To set a speed• Press SET ACCEL. For speedcontrol to operate, the speedcontrol must be ON and thevehicle speed must be greaterthan 48 km/h (30 mph).If

You can accelerate with the accelerator pedal at any time during speedcontrol usage. Releasing the accelerator pedal will return your vehicle tothe pr

Pressing OFF will erase thepreviously programmed set speed.To return to a previously set speed• Press RES. For RES to operate,the vehicle speed must b

0000000000MPH20km/h4060801001201401600102030405060708090100LOWFUELDOORAJARLOWRANGE4 X 4CRUISEBRAKE!ABS+ -LEFHRPM1000X0123564PRN 218C18HDFUEL FILLSER

TILT STEERING WHEELPull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the des

Push (tap) the end of the stalkbriefly for a single swipe (no wash).Push and hold for three swipes withwash. Push and hold for a longerwash (up to ten

The transmission will operate in allgears except overdrive. To return tonormal overdrive mode, press theTransmission Control Switch again.The TCIL (th

One touch down• Press AUTO completely down andrelease quickly. The driver’swindow will open fully. Depressagain to stop window operation.One touch dow

CHILDPROOF DOOR LOCKSWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo

2. Move the control in the directionyou wish to tilt the mirror.3. Return to the center position to lock mirrors in place.4. Adjust spotter mirrors (i

Signal mirrors (if equipped)When the turn signal is activated,the appropriate mirror will show ablinking red arrow.The arrow provides an additionalwar

• Place transmitter into storage compartment, control down.• Place the provided height adaptors onto the back of the storage bindoor as needed.• Press

Illuminated visor mirrorLift the mirror cover to turn on thevisor mirror lamps.TRIP COMPUTER (IF EQUIPPED)The trip computer tells you about the condit

Mode controlEach press of the MODE control willdisplay a different feature as follows:Average fuel economy. Thedisplay will indicate the vehicle’saver

4X4HIGH2WD4X4LOWOFFPOWER POINTOFFA/CMAXA/CFM 1AMCBL RF REWFFSCANBASSTREBSELBALTAPEDISCEJCDFADEAUTOCLKSIDE 1-2COMPSHUFFLEEJMUTEVOL PUSH ONSEEKTUNEAMFM1

• if the vehicle is started while parked on an incline.• if less than 30 liters (8 gallons) of fuel is added to the fuel tank.The fuel range function

Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Locate the trip computer

1. Locate the trip computer located in the overhead console.2. Start the vehicle.3. Press and hold both tripcomputer controls. Afterapproximately eigh

Rear courtesy/reading lamps• Second row courtesy/reading lamp• Third row courtesy/reading lampThe courtesy lamps light when:• any door is opened.• the

CENTER CONSOLEYour vehicle may be equipped with a variety of console features. Theseinclude:• Utility compartment• Coin holder slots• Pen holderUse on

Your vehicle is equipped with a remote entry system which allows you to:• unlock the vehicle doors without a key.• lock all the vehicle doors without

Sounding a panic alarmPress this control to activate thealarm.To deactivate the alarm, press thecontrol again or turn the ignition toACC or ON.Replaci

Illuminated entryThe illuminated entry system will turn on the interior lights when theremote transmitter unlock control is pressed.The illuminated en

Programming remote transmittersIt is necessary to have all (maximum of four — original and/or new) ofyour remote transmitters available prior to begin

Programming your own personal entry codeTo program your own code:1. Enter factory set code (keypad will illuminate for five seconds when akey is press

WARNING LIGHTS AND CHIMESLow fuelIlluminates as an early reminder of alow fuel condition indicated on thefuel gauge (refer to Fuel Gauge inthis chapte

Locking the doors with the keyless entry systemIt is not necessary to first enter thefactory or personal code prior tolocking all doors. To lock all t

Key informationYour vehicle is supplied with twocoded keys. Only a coded key willstart your vehicle. Spare coded keyscan be purchased from yourdealers

The correct coded key key must be used for your vehicle. The use ofthe wrong type of coded key key may lead to a “NO-START” condition.If an unprogramm

If not successful, the new coded key(s) will not start the vehicle’s engineand the theft indicator will flash on and off and you may repeat steps 1thr

The cargo doors and liftgate should be closed before driving yourvehicle. Leaving the liftgate and/or the cargo doors open couldcause serious damage t

SEATINGFull bench seat (if equipped)• Lift the track release bar to movethe seat forward or backward.Ensure that the seat is relatchedinto place.60/40

Captain’s chair (if equipped)• Lift the track release bar to movethe seat forward or rearward.Make sure that the seat isrelatched into place.• Pull th

Press front to raise or lower thefront portion of the seat cushion.Press rear to raise or lower the rearportion of the seat cushion.Press the control

Heated seats (if equipped)To operate the heated seats:• Push control to activate.• Push again to deactivate.The indicator light on the control will il

Rear folding bench seat (if equipped)Folding down rear seats into load floorEnsure that no objects such as books, purses or briefcases are on thefloor

What you should do if the Service Engine Soon light illuminatesLight turns on solid:This means that the OBD II system has detected a malfunction.Tempo

4. Stow headrest into the green capsfound on the top of the seatcushion.5. Lift the lower seat control andflip the seatback down.Seating and safety re

6. Lift up flap on seatback to releasecloseout panel.7. Rotate panel to closeout thespace between the seatback and thefloor.Returning the seat to upri

4. Remove headrest from storage position and return to 2nd rowseatback. Push down headrest completely to secure.Reclining the seatbackLift the control

1. Rotate the upper seat controlrearward while pushing the seatbacktoward the front of the vehicle.2. Push the seatback toward thefront of the vehicle

Removing the third row seatFrom the rear of the vehicle, with the liftgate window and cargo doorsopen:1. Pull the seat release lever locatedon the low

• When the rear of the seat is 10–13 cm (4–5 in) above the rear pins,let the seat drop. This will ensure that the seat will properly latch intothe flo

Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue thatare designed to be used as

Vehicle sensitive modeThe vehicle sensitive mode is the normal retractor mode, allowing freeshoulder belt length adjustment to your movements and lock

• Grasp the shoulder portion andpull downward until the entirebelt is extracted.• Allow the belt to retract. As the belt retracts, you will hear a cli

Energy Management Feature• This vehicle has a seat belt system with an energy managementfeature at the front outboard seating position to help further