Ford 2000 Excursion Manuel d'utilisateur

Before drivingIntroduction 2Instrumentation 6Controls and features 18Seating and safety restraints 74Starting and drivingStarting 108Driving 112Roadsi

government emission standards. The OBD II system also assists theservice technician in properly servicing your vehicle.The Service Engine Soon indicat

Important child restraint precautionsYou are required by law to use safety restraints for children in the U.S.and Canada. If small children ride in yo

A belt-positioning booster should be used if the shoulder belt rests infront of the child’s face or neck, or if the lap belt does not fit snugly onbot

• Keep the buckle release button pointing up and away from the safetyseat, with the tongue between the child seat and the release button,to prevent ac

Children 12 and under should be properly restrained in the rearseat whenever possible.2. Pull down on the shoulder beltand then grasp the shoulder bel

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a c

Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a

3. Locate the correct anchor for the selected seating position.• The anchors are located underthe seat frame.4. Clip the tether strap to theanchor as

5. Refer to the Installing child safety seats in combination lap andshoulder belt seating positions section of this chapter for furtherinstructions to

PREPARING TO START YOUR VEHICLEEngine starting is controlled by the powertrain control system. Thissystem meets all Canadian Interference-Causing Equi

2. Make sure the headlamps and vehicle accessories are off.3. Make sure the parking brake isset.4. Make sure the gearshift is in P(Park).3. Turn the k

Air bag readinessMomentarily illuminates when theignition is turned ON. If the lightfails to illuminate, continues to flashor remains on, have the sys

STARTING THE ENGINE1. Turn the key to 5 (START)without pressing the acceleratorpedal and release as soon as theengine starts. The key will return to4

Guarding against exhaust fumesAlthough odorless and colorless, carbon monoxide is present in exhaustfumes. Take precautions to avoid its dangerous eff

BRAKESYour service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance.Occasional brake noise is normal and o

ABS warning lampABSTheABSwarning lamp in the instrument cluster momentarily illuminateswhen the ignition is turned to the ON position. If the light do

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released.

PREPARING TO DRIVE YOUR VEHICLEUtility vehicles have a significantly higher rollover rate thanother types of vehicles.In a rollover crash, an unbelted

If you cannot move the gearshift lever out of P (Park) with ignition inthe ON position and the brake pedal depressed:1. Apply the parking brake, turn

Hold the brake pedal down while you move the gearshift leverfrom P (Park) to another position. If you do not hold the brakepedal down, your vehicle ma

The transmission control indicatorlight (TCIL) (the word OFF) on theend of the gearshift lever willilluminate.Drive – Not shown on the display. Activa

Forced DownshiftsTo gain acceleration in(Overdrive) or Drive (O/D OFF) whenpassing another vehicle, push the accelerator to the floor. Thetransmission

Anti-lock brake system (ABS)Momentarily illuminates when theignition is turned to the ONposition. If the light remains on,continues to flash or fails

If equipped with the Electronic Shift 4WD System, and theinstrument panel control is moved to 4WD Low while the vehicleis moving, the system will not

• 4x4 -momentarily illuminateswhen the vehicle is started.Illuminates when 4x4 High or 4x4LOW is engaged.• LOW RANGE –momentarilyilluminates when the

Shifting from 4x4 HIGH (4WD high) to 2WD (2WD high)Rotate the 4WD control to 2WD atany forward speed. Disengagementof the transfer case and front hubs

4. Move the 4WD control to the 4x4HIGH (4WD high) or 2WD (2WDhigh) position.5. Hold the shift command until theLOW RANGE indicator light shutsoff.6. I

Do not spin the wheels at over 56 km/h (35 mph). The tires mayfail and injure a passenger or bystander.SandWhen driving over sand, try to keep all fou

When descending a steep hill, avoid sudden braking. Shift to a lower gearwhen added engine braking is desired.When speed control is on and you are dri

• GVWR (Gross Vehicle Weight Rating): Maximum total weight ofthe base vehicle, passengers, optional equipment and cargo. TheGVWR is specific to each v

to the front of your vehicle, (potentially including weight added to thecab), the weight added should not exceed the front axle reserve capacity(FARC)

3. Subtract your loaded vehicle weight from the maximum GCWR on thefollowing charts. This is the maximum trailer weight your vehicle can towand must f

4x2 w/automatic transmissionEngine Rear axleratioMaximum GCWR-kg(lbs.)Maximum trailerweight-kg (lbs.)5.4L 3.73 5 896 (13 000) 2 812 (6 200)6.8L 3.73 7

Four wheel drive lowMomentarily illuminates when theignition is turned to the STARTposition. Illuminates whenfour-wheel drive low is engaged. Ifthe li

4x4 with automatic transmissionEngine Rear axleratioMaximum GCWR-kg(lbs.)Maximum trailerweight-kg (lbs.)5.4L 4.10 6 577 (14 500) 3 265 (7 200)6.8L 3.7

Safety chainsAlways connect the trailer’s safety chains to the frame or hook retainersof the vehicle. To connect the trailer’s safety chains, cross th

• Consult your local motor vehicle speed regulations for towing a trailer.• Use a lower gear when towing up or down steep hills. This willeliminate ex

Exceeding these limits may allow water to enter critical vehiclecomponents, adversely affecting driveability, emissions and reliability.Replace front

To adjust the cross-bar position:1. Release the latch at both ends ofthe cross-bar (both cross-bars areadjustable).2. Slide cross-bar to the desiredlo

To adjust the tie-downs:Use the adjustable tie downs to secure loads to the luggage carrier.1. Loosen the slider knobs at each end of the cross rail.2

GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford offers acomplimentary roadside assistance program. This program

Roadside coverage beyond basic warrantyIn the United States, you may purchase additional roadside assistancecoverage beyond this period through the Fo

The fuel pump shut-off switch islocated in the passenger’s foot well,by the kick panel.Use the following procedure to reset the fuel pump shut-off swi

Always replace a fuse with one that has the specified amperagerating. Using a fuse with a higher amperage rating can causesevere wire damage and could

or remains on, have the system serviced. Refer to SecuriLock娂 passiveanti-theft system in the Controls and features chapter.Safety belt warning chimeS

To remove the fuse panel cover,turn the panel fastenerscounterclockwise.To remove a fuse use the fuse pullertool provided on the fuse panelcover.FUSE1

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger CompartmentFuse Panel Description1 20A Radio, Secondary Fusing for Audio Opti

Fuse/RelayLocationFuse AmpRatingPassenger CompartmentFuse Panel Description17 15A Heated Mirrors, Rear Defroster ⬙ON⬙indicator18 10A Rear Integrated C

Power distribution boxThe power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protec

The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description1 20A* Rear Wiper2 10A* Air Bag3 15A* Qu

Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description101 50A** Ignition Switch (B1 & B3)102 30A** Power Door Locks103 40A** Auxiliary

Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description208 — Wiper HI/LOW209 — Front Washer301 — Horn Relay302 — Gasoline only-A/C (CASS)Di

Location of the spare tire and toolsThe spare tire and tools for your vehicle are stowed in the followinglocations:Tool LocationSpare tire Mounted on

2. Turn engine OFF and block thediagonally opposite wheel (block notprovided).3. Remove the jack, jack handle, lugwrench and spare tire from thestowag

• Front passenger side (4x4)• Front driver side (4x4)Make sure the jack fits into thenotched area on the differentialhousing.• Rear2000 U137 (hdw)Owne

Fuel gaugeDisplays approximately how muchfuel is in the fuel tank (when thekey is in the ON position). The fuelgauge may vary slightly when thevehicle

8. Turn the jack handle clockwiseuntil the wheel is completely off theground and high enough to installthe spare tire.To lessen the risk ofpersonal in

On all two-piece flat wheel nuts,apply one drop of motor oil betweenthe flat washer and the nut. Do notapply motor oil to the wheel nutthreads or the

Preparing your vehicleWhen the battery is disconnected or a new battery is installed, thetransmission must relearn its adaptive strategy. As a result

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

Do not connect the end of the second cable to the negative (-)terminal of the battery to be jumped. A spark may cause anexplosion of the gases that su

2. Remove the jumper cable on the negative (-) connection of thebooster vehicle’s battery.3. Remove the jumper cable from the positive (+) terminal of

After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the engine computer canrelearn its i

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center.On

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a

Do not start your engine with the air cleaner removed and donot remove it while the engine is running.OPENING THE HOOD1. Inside the vehicle, pull the

Never remove the coolant reservoir cap while the engine isrunning or hot.This gauge indicates the temperature of the engine coolant, not thecoolant le

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT5.4L V8/6.8L V10 GASOLINE ENGINESRefer to the 7.3 Liter Power Stroke Direct Injection Turbo DieselOwne

1. Make sure the vehicle is on level ground.2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan.3. Set the parking brak

Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t

that does not meet Ford material and design specifications, start-upengine noises or knock may be experienced.It is recommended you use the appropriat

If you use a brake fluid that is not DOT 3, you will causepermanent damage to your brakes.Do not let the reservoir for the master cylinder run dry. Th

Brake system fluid should be replaced on a regular basis to maintainoptimum braking performance, especially under heavy-duty drivingconditions such as

A 50/50 mixture of distilled water and Ford Premium Engine Coolantprovides:• maximum cooling system efficiency.• freeze protection down to -36° C (-34

Automotive fluids are not interchangeable; do not use enginecoolant, antifreeze or windshield washer fluid outside of itsspecified function and vehicl

Plain water may be added in an emergency, but you must replace it witha 50/50 mixture of engine coolant and distilled water as soon as possible.Check

Coolant refill capacityTo find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in the Capacities and specificatio

TachometerIndicates the engine speed inrevolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the e

What you should know about fail-safe cooling (if equipped)If the engine coolant supply is depleted, this feature allows the vehicle tobe driven tempor

Never remove the coolant reservoir cap while the engine isrunning or hot.5. Re-start the engine and take your vehicle to a service facility.Driving th

3. While the engine idles, turn the steering wheel left and right severaltimes.4. Turn the engine off.5. Recheck the fluid level on the dipstick. Do n

Low fluid levelDo not drive the vehicle if the fluidlevel is at the bottom of the dipstickand the ambient temperature isabove 10°C (50°F).Correct flui

Adjusting automatic transmission fluid levelsBefore adding any fluid, make sure the correct type is used. The type offluid used is normally indicated

3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening.Use only fluid that meets Ford specifications

For longer, trouble-free operation, keep the top of the battery clean anddry. Also, make certain the battery cables are always tightly fastened tothe

1. With the vehicle at a complete stop, set the parking brake.2. Put the gearshift in P (Park), turn off all accessories and start theengine.3. Run th

Changing the air filter element1. Loosen the clamp that securesthe air filter element in place.2. Carefully separate the two halvesof the air filter h

TRACTION-LOK AXLE (IF EQUIPPED)This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under

HEADLAMP CONTROLRotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlam

Changing the wiper bladesTo replace the wiper blades:1. Pull the wiper arm away from thewindshield and lock into the serviceposition.2. Turn the blade

U.S. Department of Transportation-Tire quality grades: The U.S.Department of Transportation requires Ford to give you the followinginformation about t

The temperature grade for this tire is established for a tire thatis properly inflated and not overloaded. Excessive speed,underinflation, or excessiv

• Five tire rotationReplacing the tiresReplace the tires when the wearband is visible through the tiretreads.When replacing full size tires, never mix

Do not replace your tires with “high performance” tires or largersize tires.Failure to follow these precautions may adversely affect thehandling of th

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsDo not overfill the fuel tank. The pressure in an overfilled tankmay cause leak

• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kindcan lead to eye and respiratory tract irritation. In severe cases,excessive or p

Choosing the right fuelUse only UNLEADED FUEL. The use of leaded fuel is prohibited by lawand could damage your vehicle.Do not use fuel containing met

your fuel supplier about gasolines that meet the World-wide FuelCharter. In Canada, look for fuels that display the Automaker’s ChoiceLogo.Cleaner air

be void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used.The fuel system may be und

4WD CONTROL (IF EQUIPPED)This control operates the 4WD.Refer to the Driving chapter formore information.Reverse sensing system (if equipped)The revers

empty. Empty reserve is the small amount of usable fuel remaining in thefuel tank after the fuel gauge indicates empty.The amount of empty reserve var

economy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In gene

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in your vehicle sche

converter and other emission control components continue to workproperly:• Use only the specified fuel listed.• Avoid running out of fuel.• Do not tur

Readiness for Inspection/Maintenance (I/M) testingIn some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics sys

Replacing headlamp bulbs1. Make sure that the headlamp control is in the OFF position.2. Open the hood.3. Disconnect the electricalconnector from the

3. Remove the two screws andcarefully disengage parkinglamp/turn signal assembly from thevehicle.4. Rotate bulb socketcounterclockwise about1⁄4turn an

Replacing tail lamp/turn/backup lamp bulbsThe tail lamp/turn/backup lampbulbs are located in the sameportion of the tail lamp assembly,one just below

To install the brakelamp assembly:1. Install the bulb socket into the lamp assembly and rotate 45 degrees.2. Install the lamp assembly on the vehicle

Function Number ofbulbsTrade numberHeadlamps 2 9007Park/turn lamp 2 3157Sidemarker lamp 2 194Tail/stop lamp 2 3157 KTurn lamp (rear) 2 3156KBackup lam

The following warning may be required by California law:CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain

The reverse sensing system detectsobstacles within approximately 1.8meters (5.9 ft.) of the rear bumperwith a decreased coverage area atthe outer corn

Washing your vehicleWash your vehicle regularly withcold or lukewarm water. Never usestrong detergents or soap. If yourvehicle is particularly dirty,

Repairing paint chipsMinor scratches or paint damage from road debris may be repaired withthe Ultra Touch Prep and Finishing Kit (#F7AZ-19K507–BA), La

Cleaning the exterior lampsWash with the same detergent as the exterior of your vehicle. Ifnecessary, use a tar remover such as Ford Extra Strength Ta

Cleaning the interior fabricRemove dust and loose dirt with a whisk broom or a vacuum cleaner.Remove fresh spots immediately. Do not use household or

MOTORCRAFT PART NUMBERSComponent* 5.4L V8 engine 6.8L V10 engineAir filter element FA-1634 FA-1634Fuel filter FG-986B FG-986BOil filter FL-820-S FL-82

FluidFord PartNameApplication CapacityEnginecoolant-DieselengineRefer to your 7.3L Diesel SupplementEngine oil(includes filterchange)-GasolineenginesM

Service refill capacities are determined by filling the rear axle to thebottom of the filler hole with the specified lubricant.3Use Ford Premium Engin

LUBRICANT SPECIFICATIONSItemFord partname orequivalentFord partnumberFordspecificationFront axle Motorcraft SAE75W-90Premium 4x4Front AxleLubricantXY-

ItemFord partname orequivalentFord partnumberFordspecificationHinges, latches,striker plates,fuel filler doorhinge and seattracksMulti-PurposeGreaseDO

Some transmission fluids may be labeled as dual usage, such asMERCON威 and MERCON威 V. These dual usage fluids are not to be usedin an automatic transmi

AUXILIARY POWER POINTThe power point is an additional power source for electrical accessories.Do not plug optional electrical accessories into the cig

41523Capacities and specifications210

IDENTIFYING YOUR VEHICLECERTIFICATION LABELThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification Label be affixedt

Ford Extended Service PlanYou can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. For

If you have questions or concerns, or are unsatisfied with the service youare receiving, follow these steps:1. Contact your Sales Representative or Se

If you own a Lincoln vehicle and are away from home when your vehicleneeds service, or if you need more help than the dealership couldprovide, after f

replacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure is not required prior to enforcing statecreated righ

Concerns are ineligible for review if the New Vehicle Limited Warrantyhas expired at receipt of your application and, in certain states eligibilityis

• a brief summary of the action taken by the dealer(s) and Ford MotorCompany• the names (if known) of all the people you contacted at thedealership(s)

You may also contact the North American Customer Assistance Center at1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 orby writing

The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emission control system and may causeengine knock

• Located on the right trim panel inthe rear cargo area.CLIMATE CONTROL SYSTEMManual heating and air conditioning systemFan speed controlControls the

Ford Deluxe Leather and Vinyl Cleaner (not available in Canada)Motorcraft Vinyl Cleaner (Canada only)Ford Extra Strength Tar and Road Oil Remover* (no

Comfort and convenienceCargo organizersCargo shadesCargo traysDash trimEngine block heatersBattery warmer/blanketCellular phone holderElectrochromatic

Protection and appearance equipmentAir bag anti-theft locksCarpeted cargo matDoor edge guardsDiamond plate splash guardsCar/truck coversCargo liners,

equipment installed in your vehicle should comply with FCC or CRTCregulations and should be installed only by a qualified servicetechnician.• Mobile c

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould im

AAccessory delay ...53Air bag supplementalrestraint system ...95and child safety seats ...97d

exterior ...201exterior lamps ...202instrument cluster lens ...202instrument panel ...

Engine block heater ...110Engine oil ...160checking and adding ...160dipstick ...

bulb specifications ...198daytime running lights ...18flash to pass ...51high beam ...

Lockschildproof ...53doors ...53Lubricant specifications ...207, 209Lumbar suppo

Since the air conditioner removes considerable moisture from the airduring operation, it is normal if clear water drips on the ground underthe air con

Seats ...74child safety seats ...101cleaning ...203SecuriLoc

Item InformationRequired fuel Unleaded fuel only - 87 octaneFuel tank capacity 166.6L (44.0 gallons)Engine oil-gasoline engines(includes filter change

fluid that indicates dual usage (MERCON威 and MERCON威 V) inan automatic transmission application requiring MERCON威 maycause transmission damage. Use of

Operating tips• In humid weather, selectbefore driving. This will reduce foggingon your windshield. After a few minutes, select any desired position.•

Your auxiliary A/C controls arelocated in the overhead console.In order for the auxiliary A/C-heatercontrols to function, the driver’sauxiliary A/C-he

Turn the fan speed control knob tothe desired speed.Turn the temperature control to thedesired temperature.If the front seat control panel is setto MA

Activating the rear window defroster will also activate the heated mirrors(if equipped). For more information refer to Heated Outside Mirrors inthis s

Turn control to raise or lowervolume.If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nomi

Tune adjust in radio mode• Pressto move to the nextfrequency down the band(whether or not a listenablestation is located there). Hold thecontrol to mo

BREAKING-IN YOUR VEHICLEThere are no particular breaking-in rules for your vehicle. During thefirst 1 600 km (1 000 miles) of driving, vary speeds fre

Seek function in radio mode• Pressto find the nextlistenable station down thefrequency band.• Pressto find the nextlistenable station up thefrequency

Scan function in tape modePress the SCAN control to hear a short sampling of all selections on thetape. (The tape scans in a forward direction. At the

Starting autoset memory preset1. Select a frequency using the AM/FM select controls.2. Press the AUTO control.3. When the first six strong stationsare

Press the TREB control then press:•to decrease the treble outputand•to increase the treble output.Speaker balance adjustSpeaker sound distribution can

Tape/CD select• To begin tape play (with a tapeloaded into the audio system)while in the radio or CD mode,press the TAPE control. Press thebutton duri

Eject functionPress the EJ control to stop andeject a tape.Press the EJ control to stop andeject a CD.Dolby姞 noise reductionDolby威 noise reduction ope

Setting the clockTo set the hour, press and hold theCLK control and press SEEK:•to decrease hours and•to increase hours.To set the minute, press and h

The CLK button will allow you toswitch between media display mode(radio station, stereo information,etc.) and clock display mode (time).When in clock

If there is a discrepancy between the rear seat and the front audiocontrols, (i.e, both trying to listen to the same playing media), the frontaudio sy

Memory preset controlPush the MEM control successivelyto allow rear seat passengers toscroll through the six memorypresets in AM, FM1, or FM2.Push the

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-

2. Press to eject the magazine.3. Turn the magazine (A) over.4. Using the disc holder releaseknob (C), pull the disc holder (B)out of the magazine.If

5. Line up the CD with the grooveof the disc holder. Ensure that thelabel on the CD faces downwards.6. Press in on the disc holder until itlocks secur

If your changer does not work, it may be that:• A disc is already loaded where you want to insert a disc.• The disc is inserted with the label surface

Radio frequency informationThe Federal Communications Commission (FCC) and the Canadian Radioand Telecommunications Commission(CRTC) establish the fre

POSITIONS OF THE IGNITION1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, locks the

SPEED CONTROLTo turn speed control on• Press ON.Vehicle speed cannot be controlleduntil the vehicle is traveling at orabove 48 km/h (30 mph).Do not us

To set a speed• Press SET/SET ACC/SET ACCEL.For speed control to operate, thespeed control must be ON andthe vehicle speed must be greaterthan 48 km/h

You can accelerate with the accelerator pedal at any time during speedcontrol usage. Releasing the accelerator pedal will return your vehicle tothe pr

Pressing OFF will erase thepreviously programmed set speed.To return to a previously set speed• Press RES/RSM/RESUME. ForRES/RSM/RESUME to operate,the

TILT STEERING WHEELPull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the des

Vehicle Symbol GlossaryChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Engine OilEngine CoolantEngine CoolantTemperat

Push (tap) the end of the stalkbriefly for a single swipe (no wash).Push and hold for three swipes withwash. Push and hold for a longerwash (up to ten

FLASH TO PASSPull toward you to activate andrelease to deactivate.OVERDRIVE CONTROL (IF EQUIPPED)Activating overdrive(Overdrive) is the normal drive p

POWER WINDOWSPress and hold the rocker switches to open and close windows.• Press the top portion of therocker switch to close.• Press the bottom port

Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controlsexcept for the driver’s press

POWER SIDE VIEW MIRRORS (IF EQUIPPED)The ignition can be in any position to adjust the power side view mirrors.To adjust your mirrors:1. Select L to a

Fold-away mirrorsPull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.Heated outside mirrors(if equipped)B

Forward storage bin (if equipped)Press the release control to openthe storage compartment. The doorwill open slightly and can be movedto full open.The

Power quarter rear windows (if equipped)Press theportion of the VENTcontrol to open the power rearquarter windows.Press theportion of the VENTcontrol

Illuminated visor mirrorTo turn on the visor mirror lamps,lift the mirror cover.TRIP COMPUTER (IF EQUIPPED)The trip computer tells you about the condi

Mode controlEach press of the MODE control willdisplay a different feature as follows:Average fuel economy. Thedisplay will indicate the vehicle’saver

0000000000MPH20km/h4060801001201401600102030405060708090100LOWFUELDOORAJARLOWRANGE4 X 4CRUISEBRAKE!ABS+ -LEFHRPM1000X0123564PRN 218C18HDFUEL FILLSER

• if the vehicle is started while parked on an incline.• if less than 30 liters (8 gallons) of fuel is added to the fuel tank.The fuel range function

Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Locate the trip computer

Compass calibration adjustmentPerform this adjustment in an open area free from steel structures andhigh voltage lines.For optimum calibration, turn o

Rear courtesy/reading lamps• Second row courtesy/reading lamp• Third row courtesy/reading lampThe courtesy lamps light when:• any door is opened.• the

CENTER CONSOLEYour vehicle may be equipped with a variety of console features. Theseinclude:• Utility compartment• Coin holder slots• Pen holder• Comp

If there is any potential remote keyless entry problem with your vehicle,ensure ALL key fobs (remote entry transmitters) are brought to thedealership,

Sounding a panic alarmPress this control to activate thealarm.To deactivate the alarm, press thecontrol again or turn the ignition toACC or ON.This de

To replace the battery:1. Twist a thin coin between the twohalves of the transmitter near thekey ring. DO NOT TAKE THEFRONT PART OF THETRANSMITTER APA

Replacing lost transmittersIf a remote transmitter has been lostand you would like to remove itfrom the vehicle’s memory, or youwould like to purchase

Keyless entry systemWith the keyless entry keypad, you can:• lock or unlock the vehicle doors without using the key.Your vehicle has a factory set 5 d

4X4HIGH2WD4X4LOWOFFPOWER POINTOFFA/CMAXA/CFM 1AMCBL RF REWFFSCANBASSTREBSELBALTAPEDISCEJCDFADEAUTOCLKSIDE 1-2COMPSHUFFLEEJMUTEVOL PUSH ONSEEKTUNEAMFM1

Unlocking the doors with the keyless entry systemTo unlock the driver’s door, enter either the factory-set code or personalcode (each digit pressed wi

vehicle starting problems and a loss of security protection. Large metallicobjects, a second key or electronic devices used to purchase gasoline orsim

Procedure to program spare SecuriLock姟 keys to your vehicleNew SecuriLock娂 keys must have the correct mechanical key cut foryour vehicle.Conventional

CARGO NET (IF EQUIPPED)The cargo net secures lightweightobjects in the cargo area. Attach thenet to the anchors provided. Thisnet is not designed to r

SEATINGFull bench seat (if equipped)• Lift the track release bar to movethe seat forward or backward.Ensure that the seat is relatchedinto place.60/40

Captain’s chair (if equipped)• Lift the track release bar to movethe seat forward or rearward.Make sure that the seat isrelatched into place.• Pull th

Press front to raise or lower thefront portion of the seat cushion.Press rear to raise or lower the rearportion of the seat cushion.Press the control

Heated seats (if equipped)To operate the heated seats:• Push control to activate.• Push again to deactivate.The indicator light will illuminate when a

The head restraints can be movedup and down.Rear folding bench seat(if equipped)Folding down rear seats intoload floorEnsure that no objects such asbo

2. Lift seat cushion up and rotateforward.3. The headrest must be removed inorder to fold the seatback down.Remove 2nd row seat headrest bypushing in

WARNING LIGHTS AND CHIMESLow fuelIlluminates as an early reminder of alow fuel condition indicated on thefuel gauge (refer to Fuel Gauge inthis chapte

5. Lift the lower seat control andflip the seatback down.6. Lift up flap on seatback to releasecloseout panel.7. Rotate panel to closeout thespace bet

2. Lift the lower seat control.3. Pull up on the seatback whilelifting the handle to lift the seatbackinto the upright position.4. Remove headrest fro

To reduce the risk of personal injury, the second row seat should not beleft in the forward, E-Z entry position while the vehicle is in motion.Please

REMOVING THE THIRD ROW SEATFrom the rear of the vehicle, with the liftgate window and cargo doors open:1. Pull the seat release lever locatedon the lo

2. Push up on the seat to verify that it is latched into the floor.3. Verify that the safety belts can move freely on either side of the seat.SAFETY R

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.Combination lap and shoulder bel

Automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt

• Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode.H

Safety belt replacement labelThe short plastic boot on the frontsafety belt at the passengeroutboard anchor location covers a“Replace Belt” label on t

Failure to follow these instructions will affect the performance ofthe safety belts and increase the risk of personal injury.Front and second row safe

What you should do if the Service Engine Soon light illuminatesLight turns on solid:This means that the OBD II system has detected a malfunction.Tempo

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ

Safety belt warning light and indicator chimeThe seat belt warning light illuminates in the instrument cluster and achime sounds to remind the occupan

The purpose of the Belt Minder is to remind occasional wearers to wearsafety belts all of the time.The following are reasons most often given for not

Do not sit on top a buckled safety belt to avoid the Belt Minderchime. Sitting on the safety belt will increase the risk of injury inan accident. To d

5. Buckle then unbuckle the safety belt three times, ending with thesafety belt unbuckled.• After step 5 the safety belt warning light will be turned

Refer to Cleaning and maintaining the safety belts in theMaintenance and care section.AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Your vehicle is equip

All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag SRS isprovided.Always transpor

Children and air bagsFor additional important safetyinformation, read all information onsafety restraints in this guide.Children must always be proper

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burn

• and the electrical wiring which connects the components.The diagnostic module monitors its own internal circuits and thesupplemental air bag electri