Before drivingIntroduction 2Instrumentation 4Controls and features 19Seating and safety restraints 113Starting and drivingStarting 139Driving 144Roads
Four wheel drive high (if equipped)This light momentarily illuminateswhen the ignition is turned to ON.Illuminates when four-wheel drivehigh is engage
CHILDPROOF DOOR LOCKSWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo
Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re
Auxiliary power pointThe power point is an additionalpower source for electricalaccessories.Rear console featuresThe rear console incorporates thefoll
POSITIVE RETENTION FLOOR MATTo install floor mats:1. Move the driver’s seat to the most rearward position2. Position the driver’s side floor mat with
Make sure that the liftgate door and/or window are closed toprevent exhaust fumes from being drawn into the vehicle. Thiswill also prevent passengers
2. Wrap the vinyl around the rollertube twice. Tuck the edges of thevinyl inside the end cap with eachwrap.3. Fold the edges of the vinyltowards the c
Unlocking the doorsPress this control to unlock thedriver’s door. The interior lamps willilluminate.Press the control a second timewithin five seconds
Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment.Memory
The memory feature will continue to work from the door control evenwhen deactivated at the remote entry module.Replacing the batteryThe transmitter is
Replacing lost transmittersTake all your vehicle’s transmittersto your dealer if service is required.If you purchase additionaltransmitters (up to fou
Safety belt warning chimeChimes to remind you to fasten your safety belts.For information on the safety belt warning chime, refer to the Seatingand sa
The autolock feature repeats when:• any door is opened and then closed• the brake pedal is releasedDeactivating autolockBefore following the activatio
If autolock/relock has been changed, the horn will chirp to confirmprocedure is complete.Keyless entry system (if equipped)With the keyless entry keyp
If you wish to erase your personal code, use the following instructions:Erasing personal code1. Enter the factory-set code.2. Press 1/2 within five se
SECURILOCKY PASSIVE ANTI-THEFT SYSTEMThe SecuriLocky passive anti-theft system provides an advanced level ofvehicle theft protection. Your vehicle’s e
Programming spare SecuriLockY keysSpare SecuriLocky keys can be purchased from your dealership andprogrammed to your SecuriLocky passive anti-theft sy
5. Within 10 seconds of turning the ignition to OFF, insert theunprogrammed SecuriLocky key (new key) into the ignition and turnthe ignition from OFF
SEATINGAdjustable head restraintsYour vehicle’s seats may be equipped with head restraints which arevertically adjustable. The purpose of these head r
Adjusting the front power seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the sea
Memory seats (if equipped)This system allows automaticpositioning of the driver seat tothree programmable positions.The memory seat control is located
head motion in the event of a rear collision. To properly adjust your headrestraints, lift the head restraint so that it is located directly behind yo
SpeedometerIndicates the current vehicle speed.Engine coolant temperature gaugeIndicates the temperature of theengine coolant. At normal operatingtemp
To return the seat to the uprightposition:• Press downward on the uppercorner of the seatback and hold.• Pull the release handle upward tounlatch the
All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag SRS isprovided.It is extremely
2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.The front and rear outboard safety restraints in the vehicle arecombinatio
How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt
• This seat belt system has a retractor assembly that is designed to payout webbing in a controlled manner. This feature is designed to helpreduce the
Safety belt extension assemblyIf the safety belt assembly is too short, even when fully extended, 20 cm(8 inches) can be added to the safety belt asse
Safety belt maintenanceInspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to ma
Important supplemental restraint system (SRS) precautionsThe supplemental restraint systemis designed to work with the safetybelt to help protect the
Do not attempt to service, repair, or modify the Air BagSupplemental Restraint System or its fuses. See your Ford orLincoln-Mercury dealer.Children an
The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burn
OdometerRegisters the total kilometers(miles) of the vehicle.Trip odometerRegisters the kilometers (miles) ofindividual journeys. To reset,depress the
• and the electrical wiring which connects the components.The diagnostic module monitors its own internal circuits and thesupplemental air bag electri
All occupants of the vehicle including the driver should alwayswear their safety belts even when an air bag SRS is provided.How does the side air bag
The fact that the air bags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of
Disposal of air bags and air bag equipped vehiclesFor disposal of air bags or air bag equipped vehicles, see your localdealership or qualified technic
If the shoulder belt portion of a combination lap and shoulder belt canbe positioned so it does not cross or rest in front of the child’s face orneck,
When installing a child safety seat:• Review and follow the informationpresented in the Air BagSupplemental Restraint Systemsection in this chapter.•
Installing child safety seats in combination lap and shoulder beltseating positions1. Position the child safety seat in aseat with a combination lap a
3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi
7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat.
The provision (attaching hole) is provided in the rear edge of the frontpassenger seat cushion frame. The anchorbracket must be installed usingthe ins
Battery voltage gaugeThis gauge shows the batteryvoltage when the ignition is in theON position. If the pointer movesand stays outside the normalopera
PREPARING TO START YOUR VEHICLEEngine starting is controlled by the ignition system. This system meetsall Canadian Interference-Causing Equipment stan
If starting a vehicle with an automatic transmission:• Make sure the parking brake isset.• Make sure the gearshift is in P (Park).If starting a vehicl
Make sure the corresponding lights illuminate briefly. If a light fails toilluminate, have the vehicle serviced.• If the driver’s safety belt is faste
4. After idling for a few seconds, apply the brake and release the parkingbrake.Using the engine block heater (if equipped)An engine block heater warm
Important ventilating informationIf the engine is idling while the vehicle is stopped in an open area forlong periods of time, open the windows at lea
BRAKESYour service brakes are self-adjusting. Refer to the maintenance guideand or service guide for scheduled maintenance.Occasional brake noise is n
ABS warning lampTheABSwarning lamp in the instrument cluster momentarily illuminateswhen the ignition is turned on and the engine is off. If the light
The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released.
• underinflated tire(s) on any wheel(s)• high crown in center of road• high crosswinds• wheels out of alignment• loose or worn components in steering
TRANSMISSION OPERATIONAutomatic transmission operationBrake-shift interlockThis vehicle is equipped with a brake-shift interlock feature that prevents
MESSAGE CENTER (IF EQUIPPED)With the ignition in the ON position,the message center displaysimportant vehicle informationthrough a constant monitor of
Driving with a 4–speed automatic transmission (if equipped)Understanding gearshift positionsPull the gearshift lever towards you and downward to move
(Overdrive)The normal driving position for thebest fuel economy. Transmissionoperates in gears one through four.(Overdrive) can be deactivatedby press
1 (First)Use 1 (Low) to provide maximumengine braking on steepdowngrades. Upshifts can be madeby shifting to 2 (Second) or to(Overdrive). Selecting 1
N (Neutral)With the gearshift in N (Neutral),the vehicle can be started and isfree to roll. Hold the brake pedaldown while in this gear.(Overdrive)The
2 (Second)Use 2 (Second) to start-up onslippery roads or to provideadditional engine braking ondowngrades. Transmission operatesin third gear.1 (First
5. Release the clutch slowly while pressing gradually down on theaccelerator pedal.• Do not drive with your foot resting on the clutch pedal. Do not u
Recommended shift speedsUpshifts when accelerating (for best fuel economy)Shift from:Transfer case position (if equipped)AUTO or HIGH LOW1 - 2 14 km/h
FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED)If equipped with the Electronic Shift 4WD System, and theinstrument panel control is moved to 4WD Low wh
• The 4WD HIGH mode providesfour-wheel drive with full powerto both axles. It is only intendedfor severe winter or off-roadconditions, such as deep sn
Using the Control-Trac systemShifting between 4WD AUTO and 4WD HIGHWhen you move the control to 4WDHIGH, the indicator light willilluminate in the ins
For maximum accuracy of this display feature, the ignition should be inthe OFF position during fueling. The display FUEL LEVEL ERRORindicates a proble
Driving off-road with 4WDYour vehicle is specially equipped for driving on sand, snow, mud andrough terrain and has operating characteristics that are
Once through water, always try the brakes. Wet brakes do not stop thevehicle as effectively as dry brakes. Drying can be improved by movingyour vehicl
Driving on snow and iceA 4WD vehicle has advantages over 2WD vehicles in snow and ice butcan skid like any other vehicle.Avoid sudden applications of
You should either know the terrain or examine maps of the area beforedriving. Map out your route before driving in the area. For moreinformation on dr
If the rear axle is submerged in water, the rear axle lubricant should bechecked and changed, if necessary. The rear axle is filled with asynthetic lu
TRACTION-LOK AXLE (IF EQUIPPED)This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under
• Maximum Trailer Weight Rating : Maximum weight of a trailer thevehicle is permitted to tow. The maximum trailer weight rating isdetermined by subtra
Calculating the load your vehicle can carry/tow1. Use the appropriate maximum gross combined weight rating (GCWR)chart to find the maximum GCWR for yo
TRAILER TOWINGTrailer towing with your vehicle may require the use of a trailer towoption package.Trailer towing puts additional loads on your vehicle
Trailer towing table (4x2 manual transmission)GCWR (Gross Combined Weight Rating)/Trailer weightsEngineRearaxleratioMaximumGCWR-kg(lbs.)Trailer weight
System checkPress the system check control todisplay the status of the followingsystems:• engine oil life left• engine oil level• voltage level• engin
Trailer towing table (4x4 manual transmission)GCWR (Gross Combined Weight Rating)/Trailer weightsEngineRearaxleratioMaximumGCWR-kg(lbs.)Trailer weight
Trailer towing table (4x2 automatic transmission)GCWR (Gross Combined Weight Rating)/Trailer weightsEngineRearaxleratioMaximumGCWR-kg(lbs.)Trailer Wei
Trailer towing table (4x4 and AWD with automatictransmission)GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR-kg(lbs.
Trailer towing table (4x4 and AWD with automatictransmission)Notes: For high altitude operation, reduce GCW by 2% per 300 meters(1 000 ft) elevation.
Safety chainsAlways connect the trailer’s safety chains to the vehicle. To connect thetrailer’s safety chains, cross the chains under the trailer tong
Driving while you towDo not drive faster than 88 km/h (55 mph) when towing a trailer.Speed control may shut off if you are towing on long, steep grade
Launching or retrieving a boatWhen backing down a ramp during boat launching or retrieval,• Do not allow the static water level to rise above the bott
LUGGAGE RACKMaximum load is 90 kg (200 lbs), evenly distributed. If it is not possibleto distribute the load, position it as far rearward as possible.
HAZARD FLASHERUse only in an emergency to warn traffic of vehicle breakdown,approaching danger, etc. The hazard flashers can be operated when theignit
The fuel pump shut-off switch islocated in the passenger’s foot well,behind the kick panel.FUSES AND RELAYSFusesIf electrical components in thevehicle
Oil change resetPress the OIL CHANGE RESETcontrol to reset the oil life feature to100% (or your personalized oil resetpercentage) (at optimal drivingc
Standard fuse amperage rating and colorCOLORFuseRatingMiniFusesStandardFusesMaxiFusesCartridgeMaxiFusesFuse LinkCartridge2A Grey Grey — — —3A Violet V
Passenger compartment fuse panelThe fuse panel is located on the lefthand side of the instrument panelfacing the driver’s side door. Pull thepanel cov
The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingDescription1 7.5A Power Mirror Switch, Power Antenna2 7.5A Blower Motor Relay, Air Bag
Fuse/RelayLocationFuse AmpRatingDescription20 7.5A RAP Module, Generic Electronic Module(GEM), Radio21 15A Flasher (Hazard)22 20A Auxiliary Power Sock
Power distribution boxThe power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protec
The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingDescription1 60A** I/P Fuse Panel2 40A** Blower Motor Relay3 50A** 4 Wheel
Fuse/RelayLocationFuse AmpRatingDescription3 30A* Heated Backlight4 15A* Fog Lamps and Daytime Running Lamps5 — Not Used6 10A* Powertrain Control Modu
CHANGING THE TIRESIf you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel
Removing the spare tire1. Insert the jack handle into therear bumper opening.The handle will stop moving andforward resistance to turning will befelt
Refer to the instruction sheet for detailed tire change instructions.1. Park on a level surface, activatehazard flashers and set the parkingbrake.2. P
HEADLAMP CONTROLRotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlam
6. Turn OFF the air suspensionswitch (if equipped). Refer to Airsuspension system in the Drivingchapter.7. Position the jack according to thefollowing
To lessen the risk ofpersonal injury, do not putany part of your body under thevehicle while changing a tire. Donot start the engine when yourvehicle
JUMP STARTING YOUR VEHICLEThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury
Connecting the jumper cables1. Connect the positive (+) booster cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
• 4.0L SOHC5. Be sure that the cables are clear of fan blades, belts and other movingparts of both engines.Jump starting1. Start the engine of the boo
Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa
2. Remove the jumper cable on the negative (-) connection of thebooster vehicle’s battery.3. Remove the jumper cable from the positive (+) terminal of
4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery.After the disabled vehicle has been started and the jumper
If equipped with air suspension, the air suspension control must beturned to the OFF position.The Ford approved towing procedure is flatbed or wheel l
ICONSIndicates a safety alert. Read thefollowing section on Warnings.Indicates vehicle information relatedto recycling and otherenvironmental concerns
Flash to passPull toward you to activate andrelease to deactivate.PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel during headl
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
• Manual transmission:1. Set the parking brake.2. Depress the clutch and place the gearshift in 1 (First).3. Turn off the engine and remove the key.4.
2. Go to the front of the vehicle and release the auxiliary latch that islocated in the center between the hood and the grill.3. Lift the hood until t
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.0L OHV V6 engine1. Windshield washer fluid reservoir2. Engine oil filler cap3. Transmission fluid di
4.0L SOHC V6 engine1. Windshield washer fluid reservoir2. Automatic transmission fluid dipstick3. Engine oil filler cap4. Engine oil dipstick5. Brake
5.0L V8 engine1. Engine coolant reservoir2. Windshield washer fluid reservoir3. Engine oil filler cap4. Automatic transmission fluid dipstick5. Brake
4. Open the hood. Protect yourself from engine heat.5. Locate and carefully remove the engine oil level indicator (dipstick).• 4.0L V6 engines• 5.0L V
• If the oil level is below the ADDmark (4.0L engines) or MIN mark(5.0L engine), add enough oil toraise the level within theADD-FULL range (4.0L engin
Do not use supplemental engine oil additives, oil treatments or enginetreatments. They are unnecessary and could, under certain conditions,lead to eng
Brake fluid is toxic.If you use a brake fluid that is not DOT 3, you will causepermanent damage to your brakes.Do not let the reservoir for the master
Temperature control knobControls the temperature of theairflow inside the vehicle.Mode selector controlControls the direction of the airflowto the ins
WINDSHIELD WASHER FLUIDChecking and adding washer fluidCheck the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with a symbol.If
If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become empty. If this occurs, addengine coolan
If you must remove the coolant reservoir cap, follow these steps to avoidpersonal injury:1. Before you remove the cap, turn the engine off and let it
For vehicles with orange coolant, no recycling process has beenapproved at this time and use of such coolant may harm engine andcooling system compone
• 4.0L OHV V6 engine• 4.0L SOHC V6 engine• 5.0L V8 engineDONOTOVERFILLPOWERSTEERINGFLUIDMaintenance and care214
1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gauge indicator will benear the center
5. Remove the dipstick, wiping it clean with a clean, dry lint free rag.6. Install the dipstick making sure it is fully seated in the filler tube.7. R
Use of a non-approved automatic transmission fluid may causeinternal transmission component damage.If necessary, add fluid in 250 mL (1/2 pint) increm
3. Fluid level should be at bottom ofthe opening.4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening.
3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening.Use only fluid that meets Ford specifications
• (Panel and floor)-Distributes outside air through the instrumentpanel registers and the floor ducts. Heating and air conditioningcapabilities are pr
If the electrolyte level in the battery is low, you can add plain tap waterto the battery, as long as you do not use hard water (water with a highmine
1. Set your parking brake.2. Put the gearshift in P (Park) (automatic transmission) or the neutralposition (manual transmission), turn off all accesso
Changing the wiper bladesTo replace the wiper blades:1. Pull the wiper arm away from thewindshield and lock into the serviceposition.2. Turn the blade
TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen
SERVICING YOUR TIRESChecking the tire pressure• Use an accurate tire pressure gauge.• Check the tire pressure when tires are cold, after the vehicle h
• 16’’ Five tire rotationReplacing the tiresReplace the tires when the wearband is visible through the tiretreads.When replacing full size tires, neve
Do not replace your tires with “high performance” tires or largersize tires.Failure to follow these precautions may adversely affect thehandling of th
Consult your dealer for information on other Ford approved methods oftraction control.WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety prec
• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kindcan lead to eye and respiratory tract irritation. In severe cases,excessive or p
Octane recommendationsYour vehicle is designed to use“Regular” unleaded gasoline with an(R+M)/2 octane rating of 87. We donot recommend the use of gas
• Remove any snow, ice or leavesfrom the air intake area (at thebottom of the windshield underthe hood).• If your vehicle has been parked with the win
Running out of fuelAvoid running out fuel because this situation may have an adverse affecton powertrain components.If you have run out of fuel:• You
If you do not use the proper fuel filler cap, the pressure in thefuel tank can damage the fuel system or cause it to workimproperly in a collision.Fue
Filling the tankFor consistent results:• Use the same filling rate setting (low — medium — high) each timethe tank is filled.• Allow three automatic c
Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin
Conditions• Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed.• Carrying unnecessary weight may reduce fuel economy (a
• Do not turn off the ignition while your vehicle is moving, especially athigh speeds.• Have the items listed in your Scheduled Maintenance Guide perf
Readiness for inspection/maintenance (I/M) testingIn some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostic (OBD
Replacing headlamp bulbsHandle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and donot to
To install the new bulb:1. With the flat side of the newbulb’s plastic base facing upward,insert the glass end of the bulb intothe lamp assembly. You
Replacing tail lamp/backup lamp bulbsThe tail lamp/backup lamp bulbs arelocated in the same portion of thetail lamp assembly, one just belowthe other.
Turning the EATC offPress OFF.Automatic operationPress AUTOMATIC and select the desired temperature. The selectedtemperature and the word AUTO will ap
License plate lamp bulbsTo change the license plate bulbs:1. Remove two screws and thelicense plate lamp assembly fromthe liftgate.2. Pull the bulb ou
AIMING THE HEADLAMPSThe alignment of your headlamps should be checked by a qualifiedservice technician if:• Oncoming motorists frequently signal you t
Waxing your vehicleWax when water stops beading on the surface. This could be every threeor four months, depending on operating conditions.Use only ca
• 5.0L• 4.0L SOHCMaintenance and care243
• 4.0L OHV• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.Cleaning the wheelsWash with the
Cleaning the wiper blades and windshieldIf the wiper blades do not wipe properly, clean the wiper blade rubberelement with undiluted windshield washer
Cleaning the interior fabricRemove dust and loose dirt with a whisk broom or a vacuum cleaner.Remove fresh spots immediately. Do not use household or
MOTORCRAFT PART NUMBERSComponent 4.0L OHV V6engine4.0L SOHC V6engine5.0L V8 engineAir filter FA-1658 FA-1658 FA-1658Fuel filter FG-986B FG-986B FG-986
Fluid Ford PartNameApplicationCapacityTransmissionfluidMotorcraftMERCONt ATF5-speedmanual2.6L (5.6 pints)4R70WAutomaticwith 5.0L V8engine13.1L (13.9 q
Fluid Ford PartNameApplicationCapacityRear axlelubricant2,Motorcraft SAE80W90Premium RearAxle LubricantRefer tofootnote 32.9-3.1L (5.5-5.8pints)Motorc
To control the temperature, selectany temperature between 18°C(65°F) and 29°C (85°F) by pressingthe blue (cooler) or red (warmer)buttons.For continuou
LUBRICANT SPECIFICATIONSItemFord PartName orequivalentFord PartNumberFordSpecificationBody hinges,latches, doorstriker platesand rotors, seattracks, f
ItemFord PartName orequivalentFord PartNumberFordSpecificationPower steeringfluidMotorcraftMERCON tATFXT-2-QDX MERCONtFordconventional andTraction-Lok
ENGINE DATAEngine4.0L OHV V6engine4.0L SOHC V6engine5.0L V8 engineCubic inches 245 245 302Horsepower 160 @ 4200 rpm 210 @ 5250 rpm 215 @ 4200 rpmTorqu
Dimensions 4-Door 4x2 XL Modelmm (in.)4-Door 4x4 XLTModel mm (in.)(1) Overall length 4 857 (191.2) 4 857 (191.2)(2) Overall width 1 783 (70.2) 1 783 (
IDENTIFYING YOUR VEHICLESafety compliance labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety ComplianceCertificat
Vehicle identification numberThe vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel.Engine numbe
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould im
Air bag supplemental restraintsystem ...126and child safety seats ...128description ...
Engine oilchecking and adding ...207dipstick ...205specifications ...205,207Exhaust fumes
speed control ...84turn signal indicator ...8Lockschildproof ...100Lumbar suppor
• Rotate the thumbwheel up for higher fan speed or down for lower fanspeed.• Press the steering wheel fan speed control up for higher fan speed ordown
Transmission ...149,215automatic operation ...149fluid, checking and adding(automatic) ...215,216flu
261
262
Item InformationRecommended fuel Unleaded fuel only - 87 octaneFuel tank capacity (2 door) 65.5L (17.3 gallons)Fuel tank capacity (4 door) 78.7L (20.8
2Ensure correct automatic transmission fluid is used for a specificapplication. Check the container to verify the fluid is MERCONt and/orMERCONt V app
• PNL•FLR-Distributes outside air through the instrument panelregisters and the floor ducts. Heating and air conditioning capabilitiesare provided in
The EATC display window will indicate REAR FAN OFF.The rear console fan will remain off until REAR FAN OFF is pressedagain.Operating tips• In humid we
Rear console climate controls (if equipped)Depending on the equipmentpackage of your vehicle, the rearconsole may be equipped with rearconsole audio/c
INFORMATION ABOUT THIS GUIDEThe information found in this guide was in effect at the time of printing.Ford may change the contents without notice and
Select for air to flow throughthese vents:REAR WINDOW DEFROSTERThe rear defroster control is locatedon the instrument panel.Press the rear defroster c
4WD CONTROL (IF EQUIPPED)This control operates the 4WD.Refer to the Driving chapter formore information.REVERSE SENSING SYSTEM (IF EQUIPPED)The revers
The reverse sensing system detectsobstacles within approximately 1.8meters (5.9 ft.) of the rear bumperwith a decreased coverage area atthe outer corn
USING YOUR AUDIO SYSTEMAM/FM stereo cassetteVolume/power controlPress the control to turn the audiosystem on or off.Turn the control to raise or lower
If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition
Seek function in radio mode• Press to find the nextlistenable station down thefrequency band.• Pressto find the nextlistenable station up thefrequency
Bass adjustThe bass adjust control allows youto increase or decrease the audiosystem’s bass output.Treble adjustThe treble adjust control allows youto
Tape select• To enter tape mode while in radiomode, press the TAPE AMScontrol.Automatic Music SearchThe Automatic Music Search featureallows you to qu
Tape direction selectPress SIDE and 1–2 at the sametime to play the alternate side of atape.Eject functionPress the control to stop and eject atape.Do
• to decrease hours and•to increase hours.To set the minute, press and holdthe CLK control and press:•to decrease minutes and•to increase minutes.SEEK
OFFRSMSETACCCOASTOFFONC0123456RPMx1000ABS!CHECKENGINEFUELRESETEFHHHSPEEDCONTO/DOFFL L 10MPH2050607030408090km/h0 0 01010012010 0 0 0 0 0406080100120
AM/FM Stereo / Single CD RadioVolume/power controlPress the control to turn the audiosystem on or off.Turn the control to raise or lowervolume.If the
AM/FM selectThe AM/FM select control works inradio and CD modes.AM/FM select in radio modeThis control allows you to select AM or FM frequency bands.
• Press to find the next listenable station up the frequency band.Seek function in CD mode• Press to listen to the nextselection.• Press to listen to
Bass adjustThe bass adjust control allows youto increase or decrease the audiosystem’s bass output.Treble adjustThe treble adjust control allows youto
Speaker fade adjustSpeaker sound can be adjustedbetween the front and rearspeakers.CD select• To begin CD play (if CD[s] areloaded), press the CD cont
• to decrease hours and•to increase hours.To set the minute, press and holdthe CLK control and press:•to decrease minutes and•to increase minutes.SEEK
Premium AM/FM Stereo/Cassette/Single CD/Premium SoundVolume/power controlPress the control to turn the audiosystem on or off.Audio power can also be t
If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition
Tune adjust for CD changer (if equipped)• Press to select the previousdisc in the CD changer. (Play willbegin on the first track of thedisc unless the
Seek function for CD or CD changer (if equipped)• Press to seek to the previoustrack of the current disc. If aselection has been playing forthree seco
PUSHODON/OFF4WDLOWOFF ONR. WIPEFFREWSIDE1 - 2BASS TREB BAL FADETAPEAMSAMFMCDCLKVOL - PUSH ONSHUFFLECOMPCDEJCDSCANDISCSTUNESEEK321456OFFA/CMAXA/CGearsh
Setting memory preset stations1. Select the frequency band with the AM/FM select control.2. Select a station. Refer to Tune adjust or Seek function fo
These stations are temporarily stored in the memory preset controls(until deactivated) and are accessed in the same manner of your originalpresets.To
Press the BAL control then press:•to shift sound to the left and•to shift sound to the right.Speaker fade adjustSpeaker sound can be adjustedbetween t
RewindThe rewind control works in tapeand CD modes.• In tape mode, radio play willcontinue until rewind is stopped(with the TAPE control) or the begin
Dolby noise reduction manufactured under license from DolbyLaboratories Licensing Corporation. “Dolby” and the double-D symbolare trademarks of Dolby
To set the minute, press and holdthe CLK control and press TUNE:•to decrease minutes and•to increase minutes.If your vehicle has a separate clockmodul
Mute modePress the control to mute theplaying media. Press the controlagain to return to the playing media.Rear seat controls (if equipped)The Persona
To activate the Personal AudioSystem, press thespeaker/headphone control. Pressthe MODE control to change audiosources (for headphone mode only).Use t
Turning the speakers on and offPress to turn all speakers on or off.Using headphonesPlug a 3.5 mm headphone (not included) into the jack. Press thespe
Memory preset controlPush the MEMORY controlsuccessively to allow rear seatpassengers to scroll through the 6memory presets in AM, FM1 orFM2.Push the
WARNING LIGHTS AND CHIMESCheck engineYour vehicle is equipped with acomputer that monitors the engine’semission control system. Thissystem is commonly
MACHT Audio System with AM/FM Stereo/Cassette/Single CDYour audio system is equipped with selective lighting, a unique lightingstrategy. This lighting
Turn control to raise or lowervolume.If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nomi
Tune adjust in radio mode• Press to move to the nextfrequency down the band(whether or not a listenablestation is located there). Hold thecontrol to m
Seek function in tape mode• Press to listen to the previous selection on the tape.• Pressto listen to the next selection on the tape.Seek function for
Radio station memory presetThe radio is equipped with six station memory preset controls. Thesecontrols can be used to select up to six preset AM stat
Bass adjustThe bass adjust control allows youto increase or decrease the audiosystem’s bass output.Press the BASS control then press:• to decrease bas
• to shift sound to the left and•to shift sound to the right.Speaker fade adjustSpeaker sound can be adjustedbetween the front and rearspeakers.Press
RewindThe rewind control works in tapeand CD modes.• In tape mode, radio play willcontinue until rewind is stopped(with the TAPE control) or the begin
Dolby noise reduction manufactured under license from DolbyLaboratories Licensing Corporation. “Dolby” and the double-D symbolare trademarks of Dolby
To set the minute, press theclock/RDS control until SELECTMIN is displayed and press:•to decrease minutes and•to increase minutes.Radio Data System (R
3. The fuel cap may not have been properly installed and securelytightened.These temporary malfunctions can be corrected by filling the fuel tankwith
RDS traffic announcement• Press the RDS control untilTRAFFIC is displayed.• Use the SELECT control to selectON or OFF. With the feature ON,use the SEE
• Classic• Country• Info• Jazz/R&B• Religious• Rock• Soft• Top 40RDS show• With the RDS menu enabled,press the RDS control untilSHOW is displayed.
Rear seat controls (if equipped)The Personal Audio System, afeature of the optional PremiumAM/FM Stereo/Cassette/SingleCD/Premium Sound and the MACHtA
Adjusting the volumePress the + control to increasevolume.Press the - control to decreasevolume.From the rear seat controls, volume control can be set
The rear speakers will cut out once the speaker on/off control is pressed.The front speaker will remain playing for the front passengers. Press thecon
• In CD mode (if equipped), use the SEEK function to access the nextor previous selection.CD changer (if equipped)The CD changer is located in one of
If you pull too hard on the disc holder, the disc holder may comecompletely out of the magazine. If this happens, reinsert the disc holderback into th
The CD magazine may be inserted or ejected with the radio power off.ONLY use the magazine supplied with the CD changer, other types willdamage the uni
Cleaning cassette player (if equipped)Clean the tape player head with a cassette cleaning cartridge after ten totwelve hours of play in order to maint
• Station overload. Weak signals are sometimes captured by strongersignals when you pass a broadcast tower. A stronger signal maytemporarily overtake
Safety beltMomentarily illuminates when theignition is turned to the ON positionto remind you to fasten your safetybelts. For more information, refer
SPEED CONTROL (IF EQUIPPED)To turn speed control on• Press ON.Vehicle speed cannot be controlleduntil the vehicle is traveling at orabove 48 km/h (30
To set a speed• Press SET/SET ACC/SET ACCEL.For speed control to operate, thespeed control must be ON andthe vehicle speed must be greaterthan 48 km/h
You can accelerate with the accelerator pedal at any time during speedcontrol usage. Releasing the accelerator pedal will return your vehicle tothe pr
To disengage speed control• Depress the brake pedal or• Depress the clutch pedal (ifequipped)Disengaging the speed control willnot erase the previousl
To return to a previously set speed• Press RES/RSM/RESUME. ForRES/RSM/RESUME to operate,the vehicle speed must be fasterthan 48 km/h (30 mph).Indicato
TILT STEERING WHEEL (IF EQUIPPED)Pull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wh
Push the control on the end of thestalk to activate washer. Push andhold for a longer wash cycle. Thewasher will automatically shut offafter ten secon
Radio control features• Press BAND/MODE to select AM,FM1, FM2, TAPE or CD (ifequipped).In Radio mode:• Press MEM/NEXT to select apreset station from m
Storage compartment (if equipped)Press the OPEN control to open thestorage compartment. The door willopen slightly and can be moved tofull open.Instal
• Press the GARAGE control toactivate the transmitter.Moon roof (if equipped)You can move the moon roof back to open the glass panel or tilt up tovent
High beamsIlluminates when the high beamheadlamps are turned on.Anti-theft system (if equipped)Refer to SecuriLocky passiveanti-theft system in the Co
Electronic compass/temperature display (if equipped)Outside air temperatureThe outside temperature display iscontained in the overhead console.The tem
Compass zone adjustment1. Determine which magnetic zoneyou are in by referring to the zonemap.2. Press and hold the MODE controluntil VAR appears in t
Compass calibration adjustmentPerform this adjustment in an openarea free from steel structures andhigh voltage lines:• Press and hold the MODE contro
Programming1. Prepare for programming theHomeLinkt Universal Transceiver byerasing the three factory defaultcodes by holding down the twooutside butto
Operating the HomeLinkT Universal TransceiverOnce programmed, the HomeLinktUniversal Transceiver can be used inplace of hand-held transmitters. Tooper
The 2nd or 3rd press from step 3 will activate the door. The HomeLinktUniversal Transceiver has now been trained to the receiver. Theremaining two but
To record a message:1. Press and release the RECbutton one time to start recording.(An audible tone will sound,confirming the onset of recording).2. P
If the DEL button is inadvertently pressed or the time allotted (5seconds) has passed, the indicator light will flash amber and an “error”tone will so
Automatic dimming rear view mirrorThe autolamp/automatic dimmingmirror is equipped with anautomatic dimming feature. Thisfeature will change from the
One touch down• Press AUTO completely down andrelease quickly. The driver’swindow will open fully. Depressagain to stop window operation.Window lockTh
Commentaires sur ces manuels