Before drivingIntroduction 2Instrumentation 5Controls and features 15Seating and safety restraints 71Starting and drivingStarting 98Driving 103Roadsid
Transmission control indicator light (TCIL)The word OFF located on the endof the gearshift lever is thetransmission control indicator light(TCIL).The
Make sure the corresponding lights illuminate briefly. If a light fails toilluminate, have the vehicle serviced.• If the driver’s safety belt is faste
Using the engine block heater (if equipped)An engine block heater warms the engine coolant, which improvesstarting, warms up the engine faster and all
Important ventilating informationIf the engine is idling while the vehicle is stopped in an open area forlong periods of time, open the windows at lea
BRAKESYour service brakes are self-adjusting. Refer to the “Service Guide” forscheduled maintenance.Occasional brake noise is normal and often does no
ABS warning lampTheABSwarning lamp in the instrument cluster momentarily illuminateswhen the ignition is turned on and the engine is off. If the light
RABS warning lampTheABSwarning lamp in the instrument cluster illuminates if a RABSfault is detected. Have your vehicle serviced as soon as possible.N
•Type BApply the parking brake wheneverthe vehicle is parked. Push pedaldownward to set the parking brake.The BRAKE warning lamp in theinstrument clus
•Type BPull the release lever to release theparking brake. Driving with theparking brake on will cause thebrakes to wear out quickly andreduce fuel ec
TRACTION-LOK AXLE (IF EQUIPPED)This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under
Do not rock the vehicle for more than a few minutes. Thetransmission and tires may be damaged or the engine mayoverheat.Always set the parking brake f
High beamsIlluminates when the high beamheadlamps are turned on.Oil pressure/Engine coolantThis light will come on when thekey is in the ON position a
R (Reverse)With the gearshift in R (Reverse),the vehicle will move backward.Always come to a complete stopbefore shifting into and out of R(Reverse).N
Each time the vehicle is started, the transmission will automaticallyreturn to normal overdrive mode.Every time the vehicle is shut off and restarted,
• GCWR (Gross Combined Weight Rating) : Maximum combinedweight of towing vehicle (including passengers and cargo) and thetrailer. The GCWR indicates t
your vehicle including both Gross Vehicle Weight and Front and RearGross Axle Weight Rating limits. Under no circumstance should theselimitations be e
Trailer Towing TableGCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR-kg(lbs.)Trailer weightrange-kg(lbs.)(0-Maximum)M
Trailer Towing TableGCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR-kg(lbs.)Trailer weightrange-kg(lbs.)(0-Maximum)M
Trailer Towing TableGCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR-kg(lbs.)Trailer weightrange-kg(lbs.)(0-Maximum)M
Trailer Towing TableGCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR-kg(lbs.)Trailer weightrange-kg(lbs.)(0-Maximum)M
Trailer Towing TableGCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR-kg(lbs.)Trailer weightrange-kg(lbs.)(0-Maximum)M
Your vehicle’s load capacity is designated by weight, not by volume, soyou cannot necessarily use all available space when loading a vehicle.Distribut
GAUGESSpeedometerIndicates the current vehicle speed.Fuel gaugeDisplays approximately how muchfuel is in the fuel tank (when thekey is in the ON posit
Trailer brakesElectric brakes and manual, automatic or surge-type brakes are safe ifinstalled properly and adjusted to the manufacturer’s specificatio
OFF) on moderately steep hills, Second (2) on steep hills, and First (1)on very steep hills.Servicing after towingIf you tow a trailer for long distan
Replace the rear axle lubricant anytime the axle has been submerged inwater. Rear axle lubricant quantities are not to be checked or changedunless a l
HAZARD LIGHTS CONTROLUse only in an emergency to warn traffic of vehicle breakdown,approaching danger, etc. The hazard flashers can be operated when t
The fuel pump shut-off switch islocated in the passenger’s foot well,behind the kick panel, except forcommercial stripped chassisvehicles.Roadside eme
For commercial stripped chassisvehicles, the fuel pump shut-offswitch is located on a bracket abovethe brake pedal.FUSES AND RELAYSFusesIf electrical
Standard fuse amperage rating and colorCOLORFuseRatingMiniFusesStandardFusesMaxiFusesCartrigdeMaxiFusesFuse LinkCartridge2A Grey Grey — — —3A Violet V
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingDescription1 20A RABS/4WABS Module2 15A Brake Warning Diode/Resistor, InstrumentCluster
Fuse/RelayLocationFuse AmpRatingDescription8 30A Radio Capacitor(s), Ignition Coil, PCMDiode, PCM Power Relay, Fuel Heater,Glow Plug Relay (Diesel Onl
Fuse/RelayLocationFuse AmpRatingDescription31 10A Right Headlamp (Low Beam), DRL32 — Not Used33 — Not Used34 10A Transmission Range (TR) Sensor35 — No
Engine coolant temperature gaugeIndicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal ar
The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingDescription1 — Not Used2 — Not Used3 — Not Used4 10A PCM Keep Alive Memory
Fuse/RelayLocationFuse AmpRatingDescription14 30A Trailer Running Lamps Relay, TrailerBackup Lamps Relay15 40A Main Light Switch16 50A RKE Module, Aux
CHANGING THE TIRESIf you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel
3. Raise the tire by turning thewrench or handle clockwise.Continue until the lift mechanism“clicks.”4. Check that the tire is tightlyseated under the
Type AType B4. Apply the parking brake and turnengine OFF.5. Block the wheel that is diagonallyopposite the tire you are changing.On E-Super Duty vehi
6. Remove the spare tire and jackfrom the storage location.7. Use the tapered end of the lugnut wrench to unscrew wheelornaments attached by retaining
• Never use the front or reardifferential as a jacking point.Rear axle jacking points:• All models except E-Super Duty• E-Super DutyRoadside emergenci
Front axle jacking points:• All modelsPlace the jack under the pin on thefront axle.3. Turn the jack handle clockwise until the wheel is completely of
• 8 lug wheelNever use wheels or lugnuts different than theoriginal equipment as this coulddamage the wheel or mountingsystem. This damage could allow
JUMP STARTING YOUR VEHICLEThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury
Battery voltage gaugeThis gauge shows the batteryvoltage when the ignition is in theON position. If the pointer movesand stays outside the normalopera
Connecting the jumper cables1. Connect the positive (+) booster cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center.It
SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a
Do not start your engine with the air cleaner removed and donot remove it while the engine is running.OPENING THE HOOD1. Inside the vehicle, pull the
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENTEngine compartment component locations1. Windshield washer fluid reservoir2. Engine oil filler cap3. A
3. Set the parking brake and ensure the gearshift is securely latched in P(Park).4. Open the hood. Protect yourself from engine heat.5. Locate and car
Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t
HEADLAMP CONTROL• Pull the headlamp control towardyou to the first position to turnon the parking lamps, tail lamps,license plate lamps and markerlamp
BRAKE FLUIDChecking and adding brake fluidBrake fluid should be checked andrefilled as needed. Refer to themaintenance guide and or serviceguide for t
WINDSHIELD WASHER FLUIDChecking and adding washer fluidCheck the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with a symbol.If
If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become empty. If this occurs, addengine coolan
4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap.Change your engine coolant a
Coolant refill capacityTo find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in the Capacities and specificatio
Continued operation will increase the engine temperature and the enginewill completely shut down, causing steering and braking effort toincrease.Once
CHECKING AND ADDING POWER STEERING FLUIDCheck the power steering fluid.Refer to the maintenance guide andor service guide for the serviceinterval sche
6. If the fluid is low, add fluid in small amounts, continuously checkingthe level until it reaches the FULL COLD range. Be sure to put thedipstick ba
operating temperature can be reached after approximately 30 km(20 miles) of driving. However, you can check the fluid without driving ifthe outside te
DRIVELINE UNIVERSAL JOINT AND SLIP YOKEYour vehicle may be equipped with universal joints that requirelubrication. Refer to the maintenance guide and
Flash to passPull toward you to activate andrelease to deactivate.PANEL DIMMER CONTROLTo adjust the brightness of theinstrument panel:• Rotateclockwis
Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lightedsubstances to come near th
If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreco
Gasoline enginesDisconnect:1. Disconnect the primary batteryground cable.2. Disconnect the auxiliary batteryframe ground.• Remove the ground bolt.• Pu
2. Reconnect the primary batteryground cable.Diesel enginesDisconnect:Secondary positive cable remains energized after disconnection.make sure the too
3. Disconnect the primary batteryground cable.4. Disconnect the primary batterypositive cable.Connect:Secondary positive cable remains energized after
WINDSHIELD WIPER BLADESCheck the wiper blades at least twice a year or when they seem lesseffective. Substances such as tree sap and some hot wax trea
INFORMATION ABOUT TIRE QUALITY GRADESNew vehicles are fitted with tiresthat have their Tire Quality Grade(described below) molded into thetire’s sidew
Temperature A B CThe temperature grades are A (the highest), B, and C, representing thetire’s resistance to the generation of heat and its ability to
• Four tire rotation• Five tire rotationMaintenance and care168
Replacing the tiresReplace the tires when the wearband is visible through the tiretreads.Failure to follow these precautions may adversely affect theh
Fan speed controlControls the volume of air circulatedin the vehicle.Temperature control knobControls the temperature of theairflow inside the vehicle
• Remove the tire chains when they are no longer needed. Do not usetire chains on dry roads.• The suspension insulation and bumpers will help prevent
• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kindcan lead to eye and respiratory tract irritation. In severe cases,excessive or p
Octane recommendationsYour vehicle is designed to use“Regular” unleaded gasoline with an(R+M)/2 octane rating of 87. We donot recommend the use of gas
• Your “Service Engine Soon” light may come on. For more informationon the “Service Engine Soon” light, refer to the Instrumentationchapter.Fuel Fille
Fuel FilterYour vehicle is equipped with a fuel filter that is mounted on theunderbody.For fuel filter replacement, see your dealer or a qualified ser
Filling the tankFor consistent results:• Use the same filling rate setting (low — medium — high) each timethe tank is filled.• Allow three automatic c
Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin
Conditions• Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed.• Carrying unnecessary weight may reduce fuel economy (a
EMISSION CONTROL SYSTEMYour vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to co
engine. This decal identifies engine displacement and gives some tune upspecifications.Please consult your “Warranty Guide” for complete emission warr
Operating tips• In humid weather, select before driving. This will help to preventyour windshield from fogging. After a few minutes, select any desire
Do not remove lamp bulbs unless they will be replaced immediately. If abulb is removed for an extended period of time, contaminants may enterthe lamp
To install the new bulb:1. With the flat side of the bulb’splastic base facing upward, insertthe glass end of the bulb into thelamp assembly. You may
High-mount brakelamp bulbsThe interior cargo lamp (if equipped) will have to be removed fromunder the high-mount brakelamp assembly located inside the
Using the right bulbsFunction Number ofbulbsTrade numberHeadlamps (low series) 2 H5054Headlamps (high series) 2 9007Park lamp and turn signal (front)
Washing your vehicleWash your vehicle regularly withcold or lukewarm water. Never usestrong detergents or soap. If yourvehicle is particularly dirty,
Cleaning the wheelsWash with the same detergent as the body of your vehicle. Do not useacid-based or alcohol-based wheel cleaners, steel wool, fuel or
Cleaning plastic exterior partsUse vinyl cleaner for routine cleaning. Clean with a tar remover ifnecessary. Do not clean plastic parts with thinners,
Cleaning and maintaining the safety beltsClean the safety belts with a mild soap solution recommended forcleaning upholstery or carpets. Do not bleach
MOTORCRAFT PART NUMBERSCom-ponent*4.2L V6engine4.6L V8engine5.4L V8engine6.8L V10engineAir filter FA-1634 FA-1634 FA-1634 FA-1634Battery(standard)BXT-
REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid HighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to line onreservoirEngineoil-
Fan speed controlControls the volume of air circulatedin the vehicle.Temperature control knobControls the temperature of theairflow inside the vehicle
Fluid Ford PartNameApplication CapacityPower steeringfluidMotorcraftMERCONt ATFAll Keep in FULLrange ondispstickRear axle Refer tofootnote 4Ford 8.8/9
Fluid Ford PartNameApplication CapacityTransmission6MotorcraftMERCONtVATFAutomatic(4R70W)13.1L(13.9 quarts)MotorcraftMERCONt ATFAutomatic(4R100)715.0L
7Ensure the correct automatic transmission fluid is used for a specificapplication. Check the container to verify the fluid is MERCONtapproved. Transm
LUBRICANT SPECIFICATIONSItem Ford partnameFord partnumberFordspecificationBrake fluid High Perfor-mance DOT 3Motor VehicleBrake FluidC6AZ-19542-AB ESA
Item Ford partnameFord partnumberFordspecificationParking brakeassembly(E-Super Duty)MotorcraftMERCONtAutomaticTransmissionFluidXT-2-QDX MERCONtFordco
ENGINE DATAEngine*4.2L V6engine4.6L V8engine5.4L V8engine6.8L V10engineCubic inches 256 281 330 415Horsepower200 @4800 rpm215 @4500 rpm235 @4450 rpm26
32145Capacities and specifications196
Cutaway/commercial stripped chassis modelsE-250 E-350 E-Super Duty(1) OverallheightRefer to Body Builder for specifications(2) Trackfront/rear1 762.8
VEHICLE IDENTIFICATION NUMBERComplete Ford built vehiclesThe vehicle identification number is attached to your vehicle in thefollowing places:• On the
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould im
ICONSIndicates a safety alert. Read thefollowing section on Warnings.Indicates vehicle information relatedto recycling and otherenvironmental concerns
Under normal conditions, your vehicle’s climate control system should beleft in any position other than MAX A/C or OFF when the vehicle isparked. This
Air bag supplemental restraintsystem ...83and child safety seats ...84description ...
bulb specifications ...183high beam ...11,15warning chime ...11Heating ...
Steering wheeltilting ...61Tires ...166,167changing ...
203
204
Recommended fuel Unleaded fuel only - 87 octaneFuel tank capacity Refer to Refill capacities in the Capacitiesand specifications chapter.Engine oilcap
• To prevent humidity buildup inside the vehicle, don’t drive with theclimate control system in the OFF position.• Don’t put objects under the front s
• To control the auxiliary fan withthis control, the rear fan switchon the front control unit must bein the rear control position.• The auxiliary unit
USING YOUR AUDIO SYSTEMAM/FM StereoAM/FM Stereo1 2 3 4 AM/FMSEEKTONECLKTUNETONE VOL12FMST DXVOLPUSHON1 2 3 4 AM/FMSEEKTONECLKTUNETONE VOL12FMST DXVOLP
Volume/power controlPress the control to turn the audiosystem on or off.Turn the control to raise or lowervolume.If the volume is set above a certain
Tune adjust in radio mode• Press to move to the nextfrequency down the band(whether or not a listenablestation is located there). Hold thecontrol to m
Bass adjustThe bass adjust control allows youto increase or decrease the audiosystem’s bass output.With the electronic stereo radio,press the TONE con
Setting the clockTo set the hour, press and hold theCLK control and press:•to decrease hours and•to increase hours.To set the minute, press and holdth
AM/FM stereo cassetteVolume/power controlPress the control to turn the audiosystem on or off.Turn the control to raise or lowervolume.If the volume is
AM/FM selectThe AM/FM select control works inradio and tape modes.AM/FM select in radio modeThis control allows you to select AM or FM frequency bands
INFORMATION ABOUT THIS GUIDEThe information found in this guide was in effect at the time of printing.Ford may change the contents without notice and
Scan functionThe scan function works in radiomode.Scan function in radio modePress the SCAN control to hear a brief sampling of all listenable station
Treble adjustThe treble adjust control allows youto increase or decrease the audiosystem’s treble output.Speaker balance adjustSpeaker sound distribut
Automatic Music SearchThe Automatic Music Search featureallows you to quickly locate thebeginning of the tape selectionbeing played or to skip to the
Eject functionPress the control to stop and eject atape.DolbyTnoise reductionDolbyt noise reduction operatesonly in tape mode. Dolbyt reducesthe amoun
To set the minute, press and holdthe CLK control and press:•to decrease minutes and•to increase minutes.Premium AM/FM Stereo/Cassette/Premium SoundYou
individual function controls will either illuminate or turn off. Thosecontrols which have a function for the specific mode of operationselected will b
• to increase volumecompensation• to decrease or shut off thevolume compensationAM/FM selectThe AM/FM select control worksin radio, tape and CD modes(
Tune adjust for CD changer• Press to select the previousdisc in the CD changer. (Play willbegin on the first track of thedisc unless the CD changer is
Scan functionThe scan function works in radio,tape or CD mode (if equipped).Scan function in radio modePress the SCAN control to hear a brief sampling
Autoset memory presetAutoset allows you to set strong radio stations without losing youroriginal manually set preset stations. This feature is helpful
Diesel-powered vehiclesRead the 7.3L Diesel Engine Owner’s Guide Supplement for informationregarding correct operation and maintenance of your diesel-
Speaker balance adjustSpeaker sound distribution can beadjusted between the right and leftspeakers.Press the BAL control. Use the SELcontrol to adjust
• In CD mode, pressing the REW control for less than three secondsresults in slow rewind. Pressing the control for more than threeseconds results in f
Compression featureCompression adjust brings soft andloud CD passages together for amore consistent listening level.Press the COMP control to activate
Premium AM/FM Stereo/Cassette/Single CD/Premium SoundVolume/power controlPress the control to turn the audiosystem on or off.Audio power can also be t
If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition
Tune adjust for CD changer (if equipped)• Press to select the previousdisc in the CD changer. (Play willbegin on the first track of thedisc unless the
Seek function for CD or CD changer• Press to seek to the previoustrack of the current disc. If aselection has been playing forthree seconds or more an
Setting memory preset stations1. Select the frequency band with the AM/FM select control.2. Select a station. Refer to Tune adjust or Seek function fo
To deactivate autoset and return to your audio system’s manually setmemory stations, press the AUTO control again.Bass adjustThe bass adjust control a
Press the BAL control then press:•to shift sound to the left and•to shift sound to the right.Speaker fade adjustSpeaker sound can be adjustedbetween t
Instrumentation5
RewindThe rewind control works in tapeand CD modes.• In tape mode, radio play willcontinue until rewind is stopped(with the TAPE control) or the begin
Dolby noise reduction manufactured under license from DolbyLaboratories Licensing Corporation. “Dolby” and the double-D symbolare trademarks of Dolby
To set the minute, press and holdthe CLK control and press TUNE:•to decrease minutes and•to increase minutes.If your vehicle has a separate clockmodul
CD changer (if equipped)The CD changer is located behind the driver’s seat in your vehicle.Slide the door to access the CDchanger magazine.Pressto eje
The magazine does not need to befull for the changer to operate.Radio power must be turned on to play the CDs in the changer. Themagazine may be store
CD and CD player care• Handle discs by their edges only. Never touch the playing surface.• Do not insert more than one disc at a time.• Do not expose
Radio reception factorsThree factors can affect radio reception:• Distance/strength. The further an FM signal travels, the weaker it is.The listenable
5. START, cranks the engine. Release the key as soon as the enginestarts.HAZARD FLASHERFor information on the hazard flasher control, refer to Hazard
To turn speed control off• Press OFF or• Turn off the vehicle ignition.Once speed control is switched off, the previously programmed set speedwill be
To set a higher set speed• Press and hold SET/SETACC/SET ACCEL. Release thecontrol when the desired vehiclespeed is reached or• Press and release SET/
010203040506070809010020 km/h406080100120140HL160MPH0000000000BRAKE188SERVICEENGINE SOONFHCEONOFFRESSETACCELCOASTInstrumentcluster(pg. 8)Driver side
To disengage speed control• Depress the brake pedal.Disengaging the speed control willnot erase the previouslyprogrammed set speed.Pressing OFF will e
TILT STEERINGPull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredpo
Push the control on the end of thestalk to activate washer. Push andhold for a longer wash cycle. Thewasher will automatically shut offafter ten secon
INTERIOR LAMPSCargo and dome lampsRear cargo lamps equipped with anON/OFF/DOOR control will lightwhen:• the doors are closed and thecontrol is in the
• Press the bottom portion of therocker switch to open.POWER DOOR LOCKS (IF EQUIPPED)Press U to unlock all doors and L tolock all doors.Memory lockIf
POWER SIDE VIEW MIRRORS (IF EQUIPPED)To adjust your mirrors:1. Selectto adjust the left mirror or to adjust the right mirror.2. Move the control in th
• Type BPress this control to unlock thedriver’s door. The interior lamps willilluminate.Press the control a second timewithin three seconds to unlock
Sounding a panic alarm• Type A• Type BPress this control to activate thealarm.To deactivate the alarm, press thecontrol again or turn the ignition toA
To replace the batteries:1. Twist a thin coin between the twohalves of the transmitter near thekey ring. DO NOT TAKE THEFRONT PART OF THETRANSMITTER A
Replacement of the battery will not cause the remote transmitter tobecome deprogrammed from your vehicle. The remote transmitter shouldoperate normall
OVERDRIVE12 34 AM/FMSEEKTONECLKTUNETONE VOL12FMST DXVOLPUSHONFANLOHICOOL WARMVENTFLROFFMIXClimate controlsystems(pg. 16)Electronic soundsystem(pg. 23)
Illuminated entryThe interior lamps illuminate when the remote entry system is used tounlock the door(s) or sound the personal alarm.The system automa
SEATINGAdjusting the front manual seatNever adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the seatbacks
Adjusting the front power seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the sea
Using the manual lumbar supportTurn the lumbar support controlclockwise to increase firmness.Turn the lumbar support controlcounterclockwise to increa
Stow the tongue end of thedetachable anchor.2. Lift and rotate the LH/RH seat latch handles rearward.3. Lift the LH/RH latch rod hook ends out of the
Always latch the vehicle seat to the floor, whether the seat isoccupied or empty. If not latched, the seat may cause injuryduring a sudden stop.Quick
2. Pull the seat latch handle, thenpull the seat toward the right side ofthe vehicle to disengage four pinsfrom the floor mount.3. Remove the seat.To
Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.All
2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.The front and rear outboard safety restraints in the vehicle arecombinatio
How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt
WARNING LIGHTS AND CHIMESBrake system warningMomentarily illuminates when theignition is turned to the ON positionand the engine is off. If the brakew
The safety belt pretensioner uses the same crash sensor system as theair bag supplemental restraint system (SRS). When the safety beltpretensioner dep
Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ
Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war
AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important supplemental restraint system (SRS) precautionsThe supplemental restraint systemis designed to wo
Steps you can take to properly position yourself away from the airbag:• Move your seat to the rear as far as you can while still reaching thepedals co
How does the air bag supplemental restraint system work?The air bag SRS is designed toactivate when the vehicle sustainssufficient longitudinal decele
Several air bag system components get hot after inflation. Do nottouch them after inflation.If the air bag is deployed, the air bag will not function
Disposal of air bags and air bag equipped vehiclesFor disposal of air bags or air bag equipped vehicles, see your localdealership or qualified technic
Do not use a forward–facing safety seat or an infant seat in thelast row of a 12– or 15–passenger Club Wagon.Children and safety beltsIf the child is
SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully fo
government emission standards. The OBD II system also assists theservice technician in properly servicing your vehicle.The Service Engine Soon indicat
Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a seating position which is capableof provid
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a c
Attaching safety seats with tether strapsSome manufacturers make safety seats that include a tether strap thatgoes over the back of the vehicle seat a
1. Position the child safety seat onthe front right-hand passenger seat.2. Adjust the front right-handpassenger seat full forward.3. Route the child s
5. Rotate the tether strap as shown.6. Clip the tether strap to the seatpedestal as shown.Do not clip the tether strap to theseat pedestal as shown.If
7. Rotate the tether strap clip asshown.8. Adjust the front right-handpassenger seat to the full rearwardposition.9. Refer to the instructions in this
Rear seating positionsAttachment holes have been provided in your vehicle to attach anchorhardware, if required. Tether anchor hardware kits (Part No.
PREPARING TO START YOUR VEHICLEEngine starting is controlled by the ignition system. This system meetsall Canadian Interference-Causing Equipment stan
2. Make sure the headlamps and vehicle accessories are off.Type AType B3. Make sure the parking brake isset.4. Make sure the gearshift is in P(Park).5
Commentaires sur ces manuels